A cation exchange model to describe Cs+ sorption at high ionic strength in subsurface sediments at Hanford site, USA

A theoretical and experimental study of cation exchange in high ionic strength electrolytes was performed using pristine subsurface sediments from the U.S. Department of Energy Hanford site. These sediments are representative of the site contaminated sediments impacted by release of high level waste (HLW) solutions containing 137Cs+ in NaNO3 brine. The binary exchange behavior of Cs+-Na+, Cs+-K+, and Na+-K+ was measured over a range in electrolyte concentration. Vanselow selectivity coefficients (Kv) that were calculated from the experimental data using Pitzer model ion activity corrections for aqueous species showed monotonic increases with increasing electrolyte concentrations. The influence of electrolyte concentration was greater on the exchange of Na+-Cs+ than K+-Cs+, an observation consistent with the differences in ion hydration energy of the exchanging cations. A previously developed two-site ion exchange model [Geochimica et Cosmochimica Acta 66 (2002) 193] was modified to include solvent (water) activity changes in the exchanger phase through application of the Gibbs-Duhem equation. This water activity-corrected model well described the ionic strength effect on binary Cs+ exchange, and was extended to the ternary exchange system of Cs+-Na+-K+ on the pristine sediment. The model was also used to predict 137Cs+ distribution between sediment and aqueous phase (Kd) beneath a leaked HLW tank in Hanfordd's S-SX tank using the analytical aqueous data from the field and the binary ion exchange coefficients for the pristine sediment. The Kd predictions closely followed the trend in the field data and were improved by consideration of water activity effects that were considerable in certain regions of the vadose zone plume.     

Cesium migration in saturated silica sand and Hanford sediments as impacted by ionic strength

Large amounts of 137Cs have been accidentally released to the subsurface from the Hanford nuclear site in the state of Washington, USA. The cesium-containing liquids varied in ionic strengths, and often had high electrolyte contents, mainly in the form of NaNO3 and NaOH, reaching concentrations up to several moles per liter. In this study, we investigated the effect of ionic strengths on Cs migration through two types of porous media: silica sand and Hanford sediments. Cesium sorption and transport was studied in 1, 10, 100, and 1000 mM NaCl electrolyte solutions at pH 10. Sorption isotherms were constructed from batch equilibrium experiments and the batch-derived sorption parameters were compared with column breakthrough curves. Column transport experiments were analyzed with a two-site equilibrium-nonequilibrium model. Cesium sorption to the silica sand in batch experiments showed a linear sorption isotherm for all ionic strengths, which matched well with the results from the column experiments at 100 and 1000 mM ionic strength; however, the column experiments at 1 and 10 mM ionic strength indicated a nonlinear sorption behavior of Cs to the silica sand. Transport through silica sand occurred under one-site sorption and equilibrium conditions. Cesium sorption to Hanford sediments in both batch and column experiments was best described with a nonlinear Freundlich isotherm. The column experiments indicated that Cs transport in Hanford sediments occurred under two-site equilibrium and nonequilibrium sorption. The effect of ionic strength on Cs transport was much more pronounced in Hanford sediments than in silica sands. Effective retardation factors of Cs during transport through Hanford sediments were reduced by a factor of 10 when the ionic strength increased from 100 to 1000 mM; for silica sand, the effective retardation was reduced by a factor of 10 when ionic strength increased from 1 to 1000 mM. A two order of magnitude change in ionic strength was needed in the silica sand to observe the same change in Cs retardation as in Hanford sediments.     

A generalised sorption model for the concentration dependent uptake of caesium by argillaceous rocks

A three-site cation exchange model is proposed to describe the concentration dependent uptake of Cs on natural argillaceous rock systems. Major premises in the model are that the sorption of Cs is dominated by the illite mineral component in the rock and that there is a fixed relationship between the site capacities of the three site types denoted as frayed edge, type II and planar sites. The definition of a “reference illite” with a cation exchange capacity of 0.2 equiv. kg^-1 allows the three site capacities to be fixed in the model calculations over the weight fraction of illite in the argillaceous rocks. Up to Cs equilibrium concentrations of 10^-3 M sorption occurs predominantly on the frayed edge and type II sites (higher affinity sites), with the planar site type playing only a minor role. Competition with Cs for sorption on the former two site types arises predominantly from monovalent cations such as K, Rb and NH₄ which have low hydration energies. H and Na (except at high concentrations) are considerably less competitive and bivalent cations such as Mg, Ca and Sr are effectively non-competitive. A consistent set of selectivity coefficients for Cs with respect to K, Rb, NH₄ and Na was derived from analyses and modelling of a wide range of Cs sorption data available in the open literature on pure illites from many different sources. The model was tested against four Cs sorption isotherm data sets determined on argillaceous rocks: Boom clay, Oxford clay, Palfris marl and Opalinus clay. The water chemistries and illite contents given in these experiments allowed the Cs sorption isotherms to be predicted. It is concluded that the Cs sorption model presented here, in which there are no free parameters, can be used to predict the uptake of Cs at equilibrium concentrations below 10^-3 M to within a factor of 2 to 3 in natural argillaceous rock systems.     

Artificial acidification of a non-acidic and an acidic headwater stream in Maine, USA

Two headwater streams with low DOC and different pHs (4.5-4.8 and 5-6.5) were acidified with H2SO4 to pH 4.1 and 4.5, respectively, for 24-h periods. Neutralization of the added acid occurred by protonation of ANC (HCO3-dominated in the higher pH stream), desorption of Ca (< 15 microeq litre(-1)) and Mg (<6 microeq litre(-1)), and desorption and dissolution of AL (<250 microg litre(-1)) from the stream bed. The concentrations of dissolved organic carbon (DOC) remained constant within the experimental reaches. The concentrations of Na, K an H4SiO4 also remained constant, indicating no detectable increase in the rate of chemical weathering in the stream bed. After acid addition was stopped, concentrations of Ca, Mg and Al decreased to below background, indicating reversible ion exchange as the principal mechanism for the mobility of Ca and Mg and to a lesser extent for Al. Repeated acidifications indicated that significant regeneration of cations on the exchange surfaces of the stream substrate occurs rapidly.     

Nutrient leaching from conifer needles in relation to foliar apoplast cation exchange capacity

Limited evidence to date suggests that acidic precipitation promotes leaching of nutrient cations from conifer foliage. In order to evaluate the relative contribution of the apoplast cation exchange complex and symplast nutrient pools to the leached ions, the magnitude of foliar leaching in response to acidic solutions was compared to foliar apoplast cation exchange capacity (CEC) for two conifer tree species (Pseudotsuga menziesii and Picea engelmanii). Leaching potential was determined by immersing detached needles in acidic solutions (pH5.6, 3.1, 2.1) over a range of time intervals (1, 4, 8, 24 h) and foliar apoplast cation exchange capacity was determined by potentiometric titration. Leaching increased with decreasing pH and increasing time of immersion. At pH values 2.1 and 3.1, equivalents of H+ depleted from the acidic solutions approximated equivalents of base cations gained by the solutions. Maximum amounts leached were less than 40 microeq g(-1) dry weight of needles for the combination of calcium, magnesium and potassium. Measured foliar apoplast CEC for these species was approximately 120 microeq g(-1) dry weight of needles. These relative magnitudes indicate that the apoplast rather than the symplast provided the leached ions. Because the apoplast foliar cation exchange capacity appears to be large relative to the rates of H+ diffusion across the cuticle, it may help to insulate the symplast nutrient reservoir from exposure to the H+ of acidic solutions bathing the foliage.     

Transport of Sr2+ and SrEDTA2- in partially-saturated and heterogeneous sediments

Strontium-90 has migrated deep into the unsaturated subsurface beneath leaking storage tanks in the Waste Management Areas (WMA) at the U.S. Department of Energy's (DOE) Hanford Reservation. Faster than expected transport of contaminants in the vadose zone is typically attributed to either physical hydrologic processes such as development of preferential flow pathways, or to geochemical processes such as the formation of stable, anionic complexes with organic chelates, e.g., ethylenediaminetetraacetic acid (EDTA). The goal of this paper is to determine whether hydrological processes in the Hanford sediments can influence the geochemistry of the system and hence control transport of Sr(2+) and SrEDTA(2-). The study used batch isotherms, saturated packed column experiments, and an unsaturated transport experiment in an undisturbed core. Isotherms and repacked column experiments suggested that the SrEDTA(2-) complex was unstable in the presence of Hanford sediments, resulting in dissociation and transport of Sr(2+) as a divalent cation. A decrease in sorption with increasing solid:solution ratio for Sr(2+) and SrEDTA(2-) suggested mineral dissolution resulted in competition for sorption sites and the formation of stable aqueous complexes. This was confirmed by detection of MgEDTA(2-), MnEDTA(2-), PbEDTA(2-), and unidentified Sr and Ca complexes. Displacement of Sr(2+) through a partially-saturated undisturbed core resulted in less retardation and more irreversible sorption than was observed in the saturated repacked columns, and model results suggested a significant reservoir (49%) of immobile water was present during transport through the heterogeneous layered sediments. The undisturbed core was subsequently disassembled along distinct bedding planes and subjected to sequential extractions. Strontium was unequally distributed between carbonates (49%), ion exchange sites (37%), and the oxide (14%) fraction. An inverse relationship between mass wetness and Sr suggested that sandy sediments of low water content constituted the immobile flow regime. Our results suggested that the sequestration of Sr(2+) in partially-saturated, heterogeneous sediments was most likely due to the formation of immobile water in drier regions having low hydraulic conductivities.     

Reactive transport modeling of column experiments on the evolution of saline-alkaline waste solutions

Leakage of saline-alkaline tank waste solutions often creates a serious environmental contamination problem. To better understand the mechanisms controlling the fate of such waste solutions in the Hanford vadose zone, we simulated reactive transport in columns designed to represent local site conditions. The Pitzer ion interaction module was used, with principal geochemical processes considered in the simulation including quartz dissolution, precipitation of brucite, calcite, and portlandite, multi-component cation exchange, and aqueous complexation reactions. Good matches were observed between the simulated and measured column data at ambient temperature ( approximately 21 degrees C). Relatively good agreement was also obtained at high temperature ( approximately 70 degrees C). The decrease of pH at the plume front is examined through formation of secondary mineral phases and/or quartz dissolution. Substantial formation of secondary mineral phases resulting from multi-component cation exchange suggests that these phases are responsible for a decrease in pH within the plume front. In addition, a sensitivity analysis was conducted with respect to cation exchange capacity, selectivity coefficient, mineral assemblage, temperature, and ionic strength. This study could serve as a useful guide to subsequent experimental work, to thermodynamic models developed for the concentrated solutions at high ionic strength and to other types of waste plume studies.     

A field experiment on cation exchange-affected multicomponent solute transport in a sandy aquifer

A field experiment was performed in an aquifer in order to study multicomponent cation-exchange processes under natural flow conditions. The aquifer is a glacial outwash plain with sandy aquifer material having a cation-exchange capacity (CEC) of 1.0 meg/100 g. A continuous injection of groundwater spiked with sodium and potassium as chlorides was accomplished over 37 days to resemble leachate contamination from landfills. The plume was monitored by sampling in a dense spatial network (length 100 m, width 20 m) over a period of 2.5 years in order to obtain breakthrough curves and spatial contour maps of the chemical compounds. Na and especially K showed a substantial retardation caused by cation-exchange processes despite the low CEC of the aquifer material. The average velocity of K⁺ was only 10% of the velocity of chloride (0.7 m day⁻¹). The relative migration velocity of Na⁺ was not a constant in the plume, but apparently influenced by dilution. Ca²⁺ and Mg²⁺ were expelled from the cation-exchange sites of the aquifer material and subsequently transported with the same velocity as chloride. The breakthrough curves of the various compounds showed multiple peaks and low concentration zones. It was concluded by calculations with PHREEQE that changes in calcite equilibrium may occur in the lower part of the aquifer, while complexation processes seem to be of no importance. Cation exchange is then the most important process in this field experiment, and further evaluation of the data by a geochemical transport model including cation exchange is recommended.     

U(VI) adsorption on aquifer sediments at the Hanford Site

Aquifer sediments collected via split-spoon sampling in two new groundwater wells in the 200-UP-1 operable unit at the Hanford Site were characterized and showed typical Ringold Unit E Formation properties dominated by gravel and sand. High iron-oxide content in Fe oxide/clay coatings caused the highest U(VI) adsorption as quantified by batch K(d) values, indicating iron oxides are the key solid adsorbent in the 200-UP-1 sediments that affect U(VI) fate and mobility. Even though U(VI) adsorption on the gravel-sized fraction of the sediments is considered to be negligible, careful characterization should be conducted to determine U(VI) adsorption on gravel, because of presence of Fe oxides coatings and diffusion-controlled adsorption into the gravel particles' interior surfaces. A linear adsorption isotherm was observed up to 10(-6) M (238 microg/L) of total U(VI) concentration in batch U(VI) adsorption tests with varying total U(VI) concentrations in spiked groundwater. U(VI) adsorption decreased with increasing concentrations of dissolved carbonate, because strong anionic aqueous uranium-carbonate complexes formed at high pH and high alkalinity conditions. Noticeable uranium desorption hysteresis was observed in a flow-through column experiment, suggesting that desorption K(d) values for aged uranium-contaminated sediments at the Hanford Site can be larger than adsorption K(d) values determined in short-term laboratory experiments and slow uranium release from contaminated sediments into the groundwater is expected.     

Cadmium adsorption and desorption behaviour on goethite at low equilibrium concentrations: effects of pH and index cations

The transport and bioavailability of cadmium is governed mainly by its adsorption-desorption reactions with minerals such as goethite--a common iron oxide mineral in variable charged and highly weathered tropical soils. Soil factors such as pH, temperature, solution Cd concentration, ionic strength and ageing affect Cd adsorption on goethite. The desorption behaviour of Cd from goethite at low concentrations is not fully understood. This study investigates the adsorption-desorption of Cd at low Cd concentrations (Cd adsorbed on goethite from 20 to 300 microM Cd solutions) in Na and Ca nitrate solutions of 0.03 M nominal ionic strengths. Synthetic goethite prepared by ageing a ferric hydroxide gel at high pH and room temperature was used for Cd adsorption and desorption studies. For desorption experiment 10 successive desorptions were made for the whole range of initial Cd concentrations (20-300 microM) in the presence of 0.01 M Ca(NO3)2 or 0.03 M NaNO3 solutions. Cadmium adsorption was found to be higher in Na+ than Ca2+ probably due to the competition of Ca2+ ions with Cd2+ ions for adsorption sites on the surfaces of goethite. The effect of index cation on Cd adsorption diminished with increase in pH from 5.0 to 6.0. Cadmium desorption decreased with increase in pH from 5.0 to 6.0 in both Na and Ca systems. After 10 successive desorptions with 0.03 M NaNO3 at the lowest initially adsorbed Cd approximately 45%, 20% and 7% of the adsorbed Cd was desorbed at pH 5.0, 5.5 and 6.0, respectively. The corresponding desorptions in the presence of 0.01 M Ca(NO3)2 were 49%, 22% and 8%, respectively. The Freundlich parameter, k, based on each progressive step of desorption at different adsorbed concentration increased with increasing desorption step, which may indicates that a fraction of Cd was resistant to desorption. Low Cd desorbability from goethite may be due to its specific adsorption and/or possibly as a result of Cd entrapment in the cracks or defects in goethite structure.     

Comparative kinetic desorption of 60Co, 85Sr and 134Cs from a contaminated natural silica sand column: influence of varying physicochemical conditions and dissolved organic matter

In order to determine the mechanisms of the retention of 60Co, 85Sr and 134Cs in natural silica sand columns, desorption experiments were performed by changes of pH and ionic strength and by injection of natural organic matter (NOM). Injection of KCl (0.1 M) resulted in a high release of 60Co (60-100%) and 85Sr (72-100%) but a smaller release of 134Cs (31-66%). Only limited release of 60Co (66%) and 85Sr (71%) and no release of 134Cs were observed by injection of NOM. The different percentages of desorption were related to the chemical characteristics of the organic colloids previously retained in columns before the desorption step. The results evidenced different sorption processes on energetically heterogeneous surface sites. According to the initial conditions, the binding of the radionuclides to the solid phase resulted from weak and easily reversible sorption processes to strong association probably by inner sphere complexes. The rather weak release of 134Cs by KCl was attributed to the strong retention of 134Cs by clay coatings on the natural silica sand surfaces.     

Acid rain and nitrogen deposition in a sub-tropical watershed (Piracicaba): ecosystem consequences

High levels of wet N and acidic deposition were measured in southeast Brazil. In this study we addressed the sensitivity of water bodies and soils to acidification and N deposition in the Piracicaba River basin (12,400 km2). Average acid neutralization capacity (ANC) at 23 river sampling sites varied from 350 to 1800 microeq l(-1). Therefore, rivers and streams in the Piracicaba basin are well buffered, if the lower limit of 200 microeq l(-1) is assumed as an indication of poorly buffered waters. ANC is increased by untreated wastewaters discarded into rivers and streams of the region. Average NO3 concentrations varied from 20 to 70 microeq l(-1). At the most polluted river sites, NO3 concentration is not highest, however, probably due to NO3 reduction and denitrification. Most of the nitrogen in streams is also provided by wastewaters and not by wet deposition. The majority of the soils in the basin, however, are acidic with a low base cation content and high aluminum concentration. Therefore, soils in this basin are poorly buffered and, in areas of forest over sandy soils, acidification may be a problem.     

The MAGIC simulation of surface water acidification at, and first year results from, the Bear Brook Watershed Manipulation, Maine, USA

The catchments of East and West Bear Brooks, Maine, USA, have been hydrologically and chemically monitored for 3.5 years. Stream chemistries and hydrographs are similar. These clear water streams are low in ANC (0-70 microeq litre(-1)), with variations caused by changing concentrations of base cations, SO4, NO3 and Cl. The latter range between 90-120, 0-40 and 65-75 microeq litre(-1), respectively. The West Bear catchment is being treated with six applications per year of dry (NH4)2SO4 at 1800 eq ha(-1) year(-1). After one year of treatment, the response of the stream chemistry and the response modelled by MAGIC are similar. Retentions of NH4 and SO4 are nearly 100% and greater than 80%, respectively. The additional flux of SO4 is compensated principally by an increased Ca concentration. Episodes of high discharge in the treated catchment are now characterized by lower ANC and pH, and higher Al than prior to the manipulation. Concentrations of NO3 have increased about 10 microeq litre(-1) during the dormant season, presumably due to additional nitrification of N from NH4. Discharge-chemistry relationships indicate that changes in stream chemistry, except for NO3, are dominated by ion exchange reactions in the upper part of the soil profile.     

Experimental study and modeling of the transfer of zinc in a low reactive sand column in the presence of acetate

Nowadays, it is necessary to understand and identify the reactions governing the fate of heavy metals introduced into the environment with low complexing organic compounds, particularly when they are transferred through soils in urban areas. In this work the concomitant influence of pH and acetate on the fate of zinc on siliceous sand was studied in batch and non-saturated column experiments. Total zinc concentrations varied between 2 and 20 mg/l, and total acetate concentrations were fixed at 22, 72, 132, and 223 mM to obtain solution pHs of 4, 5, 6 and 7, respectively. Natural sand (diameter, 0.3-2 mm), mainly constituted of silica, was used. In batch adsorption experiments, zinc adsorption is insignificant at pH 4, low and linear at pH 5, and increasingly nonlinear, of the Langmuir type, at pH 6 and 7 indicating near-saturation conditions of surface sites at these high pH values. In column experiments, Zn retardation increases and the maximum outlet concentration of Zn decreases with rising pH and acetate concentrations. Previous column tracer experiments revealed the occurrence of regionalized water transport in the column. Modeling these data was based on a non-electrostatic approach. Batch and column data modeling was based on the PHREEQC code that allows concomitant resolution of chemical speciation and regionalized water transport. The speciation calculation indicates that the ZnAcetate+ species is the dominant Zn species in the solutions used. Batch experimental curves are correctly modeled assuming the formation of the three surface species triple bond SiOZn+, triple bond SiOH-Zn Acetate+ and triple bond SiO-Zn(Acetate)2-. The column data could be adequately modeled assuming a two-region water transport and the formation of the same three species with the same thermodynamic constants determined in the batch experiments. The hypothesis of the modeling leads to a slight overestimation of the quantities of zinc eluted (10%) at pH 6 and 7, mostly in the desorption phase. These results show that the methodology used facilitates the correct modeling of both batch and transport experiments and formulation of the hypothesis on the interactions between the low reactive sand and a complex solution.     

Reactive barriers for 137Cs retention

137Cs was dispersed globally by cold war activities and, more recently, by the Chernobyl accident. Engineered extraction of 137Cs from soils and groundwaters is exceedingly difficult. Because the half-life of 137Cs is only 30.2 years, remediation might be more effective (and less costly) if 137Cs bioavailability could be demonstrably limited for even a few decades by use of a reactive barrier. Essentially permanent isolation must be demonstrated in those few settings where high nuclear level wastes contaminated the environment with 135Cs (half-life 2.3 x 10(6) years) in addition to 137Cs. Clays are potentially a low-cost barrier to Cs movement, though their long-term effectiveness remains untested. To identify optimal clays for Cs retention, Cs desorption was measured for five common clays: Wyoming Montmorillonite (SWy-1), Georgia Kaolinites (KGa-1 and KGa-2), Fithian Illite (F-Ill), and K-Metabentonite (K-Mbt). Exchange sites were pre-saturated with 0.16 M CsCl for 14 days and readily exchangeable Cs was removed by a series of LiNO3 and LiCl washes. Washed clays were then placed into dialysis bags and the Cs release to the deionized water outside the bags measured. Release rates from 75 to 139 days for SWy-1, K-Mbt and F-Ill were similar; 0.017% to 0.021% sorbed Cs released per day. Both kaolinites released Cs more rapidly (0.12% to 0.05% of the sorbed Cs per day). In a second set of experiments, clays were Cs-doped for 110 days and subjected to an extreme and prolonged rinsing process. All the clays exhibited some capacity for irreversible Cs uptake. However, the residual loading was greatest on K-Mbt (approximately 0.33 wt.% Cs). Thus, this clay would be the optimal material for constructing artifical reactive barriers.     

Accelerated transport of (90)Sr following a release of high ionic strength solution in vadose zone sediments

Numerical simulation of cation exchange and mineral precipitation/dissolution reactions using the multiphase reactive geochemical transport code TOUGHREACT has provided important insight into the distribution of (90)Sr among layers of geologic strata in a complex vadose zone at the U. S. Department of Energy's Idaho National Laboratory. During a transfer operation in November 1972, 70.4 m(3) of acidic, high ionic strength liquid containing 15,900 Ci of (90)Sr was released over five days into alluvial gravels 137 m above the Snake River Plain Aquifer. Sampling data from perched water zones 33 m below the release contain very high levels of (90)Sr as do soil samples obtained nearer the point of release. Use of traditional simulation approaches using laboratory-measured constant partitioning coefficients (K(d)) cannot simultaneously explain perched water and soil concentrations. To address the discrepancy, a reactive transport approach was adopted to include competitive cation exchange, dissolution/precipitation of calcite, carbon dioxide gas production and transport, and gibbsite precipitation. Simulation results using this model suggest that some of the (90)Sr could have been transported very rapidly immediately after the release with the acceleration facilitated by competition for cation exchange sites with high sodium concentrations in the released liquid and calcium dissolved from calcite, and to a lesser extent by formation of aqueous complexes with nitrate. Once the leading edge of the liquid assemblage was flushed from the alluvium, the mobility of the remaining (90)Sr decreased significantly in the absence of the competing cations. Calculations indicate that there should be a net increase in calcite, suggesting that (90)Sr could be entrained in the mineral lattice, but insufficient field data exist for confirmation. Sensitivity studies show that the cation exchange selectivity coefficients were the most sensitive individual parameters determining the (90)Sr distribution. However, the most sensitive overall quantity was the total ion exchange capacity which is a function of the moles of exchange sites per volume of pore water, the cation exchange capacity, and the total volume wetted by the infiltrating solution. In contrast, the future mobility of (90)Sr was found to be relatively insensitive to the normal range in the composition of influxing precipitation and anthropogenic waters.     

Caesium selectivity and fixation by vermiculite in the presence of various competing cations

Caesium selectivity coefficients (k(G)) that were determined with respect to Na-, Mg-, Ca-, Sr- and Ba-ions, for Kent and Libby vermiculites,ranged from 4.8 to 11 (litres/mol) [Formula: see text], much higher than those with respect to K- and NH(4)-ions (0.01 to 0.06), indicating the high affinity of vermiculite for the weakly hydrated cations. Higher K(G) values were also found for low and extremely low Cs concentrations. Vermiculite samples were very effective in removing (137)Cs from solutions containing traces of (137)Cs (4 ng litre(-1)) and extremely higher quantities of K-, NH(4)-, Na-, Mg- and Ca-ions (500 mg litre(-1)). 0.5N chloride solutions of H, NH(4), K, Na, Mg and Ca were unable to remove Cs from Cs-saturated v vermiculite samples which had undergone heating at 110 degrees C. Significant quantities (50-65%) of fixed Cs were removed from these samples only after treatment with strong acids. The high preference and fixing ability of vermiculite for Cs suggests the use of this mineral as a radioactive Cs decontaminating agent.     

The occurrence and bioavailability of radioactive 137Cs in small forest lakes in Southern Finland

Following the Chernobyl accident in late April 1986, central Finland was subjected to considerable radioactive fallout. The radioactive isotope of caesium, (137)Cs, was potentially the most harmful isotope in the fallout because of its long half-life (30 years). (137)Cs activities remained unexpectedly low within the biota (algae, zooplankton, aquatic moss, fish) of some humic forest lakes in southern Finland compared to the clear water lakes within the same district. This observation suggested that humic substances, by binding (137)Cs chemically, may reduce its bioavailability in lake water. Our laboratory experiments (throughflow systems; gel chromatography) demonstrated that binding of (137)Cs by humic substances was negligible in untreated lake waters; only when most of the alkali metals had been removed with an ion exchange resin was any binding of (137)Cs by low molecular humic fractions apparent. Instead, the concentrations of cations (especially potassium) were of overwhelming importance for the bioavailability of (137)Cs within the lacustrine ecosystems. The concentrations of (137)Cs within food chains are expected to stay at a high level for many years especially in lakes with long water renewal times.     

Reactive barriers for Cs retention

¹³⁷Cs was dispersed globally by cold war activities and, more recently, by the Chernobyl accident. Engineered extraction of ¹³⁷Cs from soils and groundwaters is exceedingly difficult. Because the half-life of ¹³⁷Cs is only 30.2 years, remediation might be more effective (and less costly) if ¹³⁷Cs bioavailability could be demonstrably limited for even a few decades by use of a reactive barrier. Essentially permanent isolation must be demonstrated in those few settings where high nuclear level wastes contaminated the environment with ¹³⁵Cs (half-life 2.3×10⁶ years) in addition to ¹³⁷Cs. Clays are potentially a low-cost barrier to Cs movement, though their long-term effectiveness remains untested. To identify optimal clays for Cs retention, Cs desorption was measured for five common clays: Wyoming Montmorillonite (SWy-1), Georgia Kaolinites (KGa-1 and KGa-2), Fithian Illite (F-Ill), and K-Metabentonite (K-Mbt). Exchange sites were pre-saturated with 0.16 M CsCl for 14 days and readily exchangeable Cs was removed by a series of LiNO₃ and LiCl washes. Washed clays were then placed into dialysis bags and the Cs release to the deionized water outside the bags measured. Release rates from 75 to 139 days for SWy-1, K-Mbt and F-Ill were similar; 0.017% to 0.021% sorbed Cs released per day. Both kaolinites released Cs more rapidly (0.12% to 0.05% of the sorbed Cs per day). In a second set of experiments, clays were Cs-doped for 110 days and subjected to an extreme and prolonged rinsing process. All the clays exhibited some capacity for irreversible Cs uptake. However, the residual loading was greatest on K-Mbt (0.33 wt.% Cs). Thus, this clay would be the optimal material for constructing artifical reactive barriers.