应用表面活性剂-生物柴油微乳液去除污染土壤中多环芳烃

针对修复焦化厂高浓度多环芳烃污染土壤高成本的现实,采用以非食用性植物油、生物柴油、表面活性剂及其乳化合成的微乳液为淋洗剂,比较不同淋洗剂的淋洗效果。结果表明乳化合成的微乳液对焦化厂土壤中多环芳烃的总去除率高于单独使用表面活性剂为淋洗剂对土壤中多环芳烃的总去除率,说明生物柴油及植物油与表面活性剂乳化形成的微乳液对原污染土壤中的多环芳烃具有显著的增溶作用。1%TW-80和2.5%TW-80对土壤中多环芳烃总去除率分别为11%和14%;以2.5%TW-80为原料乳化合成的微乳液的淋洗去除率较以1%TW-80为原料乳化合成的微乳液高,总去除率分别为15%～30%和11%～18%;以生物柴油为原料乳化合成的微乳液的淋洗去除率较以植物油为原料乳化合成的微乳液高,分别为17%～30%和15%～23%,且对多环芳烃的去除率与其辛醇水分配系数(logKow)呈线性相关关系。     

工艺参数对表面活性剂洗涤修复PAHs污染土壤的影响

采用土壤洗涤(soil-washing)技术,分别用TritonX-100和Tween-80为强化洗涤剂研究了搅拌强度、洗涤时间、表面活性剂浓度、液固比、温度和间歇搅拌6个工艺参数对PAHs污染土壤洗涤效果的影响。通过一系列烧杯搅拌实验得到最佳洗涤工艺参数。TritonX-100和Tween-80的最佳洗涤时间分别是30 min和60 min,其他工艺参数最佳条件均相同。分别是搅拌强度为250 r/min,表面活性剂浓度为5 g/L,液固比为10∶1,温度为室温和连续搅拌。在此最佳工艺参数条件下,污染土中PAHs的残留率<10%,基本上满足目标污染物的修复目标。应用表面活性剂强化洗涤技术修复PAHs污染土壤是合理和可行的。     

Selection of surfactant in remediation of DDT-contaminated soil by comparison of surfactant effectiveness

With an aim to select the most appropriate surfactant for remediation of DDT-contaminated soil, the performance of nonionic surfactants Tween80, TX-100, and Brij35 and one anionic surfactant sodium dodecyl benzene sulfonate (SDBS) in enhancement of DDT water solubility and desorption of DDT from contaminated soil and their adsorption onto soil and ecotoxicities were investigated in this study. Tween80 had the highest solubilizing and soil-washing ability for DDT among the four experimental surfactants. The adsorption loss of surfactants onto soil followed the order of TX-100 > Tween80 > Brij35 > SDBS. The ecotoxicity of Tween80 to ryegrass (Lolium perenne L.) was lowest. The overall performance considering about the above four aspects suggested that Tween80 should be selected for the remediation of DDT-contaminated soil, because Tween80 had the greatest solubilizing and soil-washing ability for DDT, less adsorption loss onto soil, and the lowest ecotoxicity in this experiment.     

胶团强化超滤法(MEUF)去除废水中氯苯的研究

研究了3种单一表面活性剂十二烷基硫酸钠(SDS)、十六烷基三甲基溴化铵(CTMAB)、聚氧乙烯失水山梨脂肪酸酯醇醚(TW80)和混合表面活性剂TW80-SDS对氯苯(CB)的强化超滤,以期为有机废水胶团强化超滤技术提供参考。结果表明,进料液静置时间对去除率无显著影响,而振荡时间在1 h后对去除率影响不大。氯苯的去除率随进料液中表面活性剂浓度的增大而增大,单一的表面活性剂对氯苯的去除效果顺序为TW80CTMABSDS,且表面活性剂对氯苯的去除效果与表面活性剂的临界胶束浓度值(CMC)、亲水-亲油平衡值(HLB)呈负相关。阴-非混合表面活性剂TW80-SDS对氯苯的去除效果明显强于单一的SDS,且去除率随着非离子表面活性剂质量分数的增加而增加。渗透通量随着进料液中表面活性剂浓度的增加而下降,单一表面活性剂种类对渗透通量的影响顺序为SDSTW80CTMAB,混合表面活性剂中随着非离子表面活性剂质量分数的增加而渗透液的渗透通量越低。     

Combined effect of nonionic surfactant Tween 80 and DOM on the behaviors of PAHs in soil--water system

Batch experiments were performed to examine the desorption behavior of phenanthrene and pyrene in soil–water system in the presence of nonionic surfactant Tween 80 and dissolved organic matter (DOM) derived from pig manure or pig manure compost. Addition of 150 mg l⁻¹ Tween 80 desorbed 5.8% and 2.1% of phenanthrene and pyrene from soil into aqueous phase, respectively, while the addition of both Tween 80 and DOM derived from pig manure compost and pig manure could further enhance the desorption of phenanthrene to 15.8% and 16.2%, respectively, and 6.4% and 10.9%, respectively, for pyrene. In addition, our finding also suggested that subsequent addition of Tween 80 into the soil–water system could further enhance PAHs desorption. The enhancement effect of the co-existence of Tween 80 and DOM was more than the additive effect of the Tween 80 and DOM individually. It is likely that the formation of DOM–surfactant complex in the soil–water system may be a possible reason to explain such desorption enhancement phenomenon. Therefore, it is anticipated that the coexistence of both Tween 80 and DOM derived from pig manure or pig manure compost in soil environment will enhance the bioavailability of PAHs as well as other hydrophobic organic contaminants (HOCs) by enhancing the desorption during remediation process.     

Environmental features of two commercial surfactants widely used in soil remediation

One of the main limitations for a wider application of surfactants in soil remediation is the lack of knowledge about environmental fate and toxicity of surfactant itself especially for in situ application. Sorption behaviour, biodegradability, toxicity of parent compound and its metabolites are important processes that affect environmental fate of surfactants in site remediation applications. Tween 80 (poly(oxyethylene)(20)-sorbitane monooleate) and Aerosol MA+80 (dihexyl sodium sulfosuccinate) are surfactants that have been tested in laboratory and field scale remediation of soil and groundwater. In this work, the sorption and biodegradability of these surfactants were assessed to provide conditions and limitations for their use. The soil used in this experimentation was analysed for organic carbon content, soil bacteria, and size fraction and resulted to be a good model because is characterised by mean values for almost all considered parameters. Tween 80 showed high degree of biodegradability but a high affinity for soil matrix. Results suggest that Tween 80 could find its best application in ex situ solid phase remediation like ex situ bioremediation; its high affinity to soil could limit in situ applications. Biodegradation tests for Aerosol MA+80 show low degree of biodegradability and mineralisation. Biodegradation experiments, coupled with analysis of toxicity, could support the hypothesis that degradation of Aerosol MA+80 is not complete and leads to an accumulation of intermediates with at least the same toxicity of the parental compound. Therefore, aquifer remediation application with Aerosol MA+80 has to be conducted with necessary precautions to avoid product loss and excess surfactant should be flushed from the soil.     

Oxidation of a PAH polluted soil using modified Fenton reaction in unsaturated condition affects biological and physico-chemical properties

A batch experiment was conducted to assess the impact of chemical oxidation using modified Fenton reaction on PAH content and on physico-chemical and biological parameters of an industrial PAH contaminated soil in unsaturated condition. Two levels of oxidant (H₂O₂, 6 and 65 g kg⁻¹) and FeSO₄ were applied. Agronomic parameters, bacterial and fungal density, microbial activity, seed germination and ryegrass growth were assessed. Partial removal of PAHs (14% and 22%) was obtained with the addition of oxidant. The impact of chemical oxidation on PAH removal and soil physico-chemical and biological parameters differed depending on the level of reagent. The treatment with the highest concentration of oxidant decreased soil pH, cation exchange capacity and extractable phosphorus content. Bacterial, fungal, and PAH degrading bacteria densities were also lower in oxidized soil. However a rebound of microbial populations and an increased microbial activity in oxidized soil were measured after 5 weeks of incubation. Plant growth on soil treated by the highest level of oxidant was negatively affected.     

Dissolution and removal of PAHs from a contaminated soil using sunflower oil

This study reports on the feasibility of remediation of polycyclic aromatic hydrocarbon (PAH) contaminated soils using sunflower oil, an environmentally-friendly solvent. Batch experiments were performed to test the influence of oil/soil ratio on the remediation of PAH contaminated soil, and to test the mass transfer behaviors of PAHs from soil to oil. An empirical model was employed to describe the kinetics of PAH dissolution and to predict equilibrium concentrations of PAHs in oil. PAH containing oil was regenerated using active carbon. Results show that dissolution of PAHs from a Manufactured Gas Plant (MGP) soil at oil/soil ratios of one or two were almost the same. Nearly all PAHs (81-100%) could be removed by sunflower oil dissolution. Mass transfer coefficients for low molecular PAHs namely fluoranthene, phenanthrene and anthracene were one or two orders of magnitude higher than those for high molecular PAHs with 4-6 rings. Ninety milliliters of PAH containing oil could be regenerated by 10 g active carbon in a batch reactor. Such a remediation procedure indicates that sunflower oil is a promising agent for the removal of PAHs from MGP soils. However, further research is required before the method can be used for in situ remediation of contaminated sites.     

PAH removal from spiked municipal wastewater sewage sludge using biological, chemical and electrochemical treatments

Polycyclic aromatic hydrocarbons (PAHs) have been widely studied due to their presence in all the environmental media and toxicity to life. These molecules are strongly adsorbed on the particulate matters of soils, sludges or sediments because of their strong hydrophobicity which makes them less bioavailability, thus limiting their bioremediation. Different sludge treatment processes were tested to evaluate their performances for PAH removal from sludge prealably doped with 11 PAHs (5.5mg each PAH kg(-1) of dry matter (DM)): two biological processes (mesophilic aerobic digestion (MAD) and simultaneous sewage sludge digestion and metal leaching (METIX-BS)) were tested to evaluate PAH biodegradation in sewage sludge. In parallel, two chemical processes (quite similar Fenton processes: chemical metal leaching (METIX-AC) and chemical stabilization (STABIOX)) and one electrochemical process (electrochemical stabilization (ELECSTAB)) were tested to measure PAH removal by these oxidative processes. Moreover, PAH solubilisation from sludge by addition of a nonionic surfactant Tween 80 (Tw80) was also tested. The best yields of PAH removal were obtained by MAD and METIX-BS with more than 95% 3-ring PAH removal after a 21-day treatment period. Tw80 addition during MAD treatment increased 4-ring PAHs removal rate. In addition, more than 45% of 3-ring PAHs were removed from sludge by METIX-AC and during ELECSTAB process were quiet good with approximately 62% of 3-ring PAHs removal. However, little weaker removal of 3-ring PAHs (<35%) by STABIOX. None of the tested processes were efficient for the elimination of high molecular weight (> or = 5-ring) PAHs from sludge.     

Remediation of PAH contaminated soils: application of a solid-liquid two-phase partitioning bioreactor

The feasibility of a two-step treatment process has been assessed at laboratory scale for the remediation of soil contaminated with a model mixture of polycyclic aromatic hydrocarbons (PAHs) (phenanthrene, pyrene, and fluoranthene). The initial step of the process involved contacting contaminated soil with thermoplastic, polymeric pellets (polyurethane). The ability of three different mobilizing agents (water, surfactant (Biosolve) and isopropyl alcohol) to enhance recovery of PAHs from soil was investigated and the results were compared to the recovery of PAHs from dry soil. The presence of isopropyl alcohol had the greatest impact on PAH recovery with approximately 80% of the original mass of PAHs in the soil being absorbed by the polymer pellets in 48 h. The second stage of the suggested treatment involved regeneration of the PAH loaded polymers via PAH biodegradation, which was carried out in a solid-liquid two-phase partitioning bioreactor. In addition to the PAH containing polymer pellets, the bioreactor contained a microbial consortium that was pre-selected for its ability to degrade the model PAHs and after a 14 d period approximately 78%, 62% and 36% of phenanthrene, pyrene, and fluoranthene, respectively, had been desorbed from the polymer and degraded. The rate of phenanthrene degradation was shown to be limited by mass transfer of phenanthrene from the polymer pellets. In case of pyrene and fluoranthene a combination of mass transfer and biodegradation rate might have been limiting.     

Remediation of phenanthrene-contaminated soil by simultaneous persulfate chemical oxidation and biodegradation processes

Polycyclic aromatic hydrocarbons (PAHs) are ubiquitous compounds with carcinogenic and/or mutagenic potential. To address the limitations of individual remediation techniques and to achieve better PAH removal efficiencies, the combination of chemical and biological treatments can be used. The degradation of phenanthrene (chosen as a model of PAH) by persulfate in freshly contaminated soil microcosms was studied to assess its impact on the biodegradation process and on soil properties. Soil microcosms contaminated with 140 mg/kg_{DRY SOIL} of phenanthrene were treated with different persulfate (PS) concentrations 0.86–41.7 g/kg_{DRY SOIL} and incubated for 28 days. Analyses of phenanthrene and persulfate concentrations and soil pH were performed. Cultivable heterotrophic bacterial count was carried out after 28 days of treatment. Genetic diversity analysis of the soil microcosm bacterial community was performed by PCR amplification of bacterial 16S rDNA fragments followed by denaturing gradient gel electrophoresis (DGGE). The addition of PS in low concentrations could be an interesting biostimulatory strategy that managed to shorten the lag phase of the phenanthrene biological elimination, without negative effects on the physicochemical and biological soil properties, improving the remediation treatment.     

Remediation of a biodiesel blend-contaminated soil by using a modified Fenton process

A soil contaminated with a B20 biodiesel blend (20 % biodiesel, 80 % diesel) has been treated by modified Fenton process with or without chelant addition. All experiments were conducted without pH adjustment. The reagents used were as follows: hydrogen peroxide as oxidant (400–4,000 mmol L^?1), ferric ion as catalyst (5–20 mmol L^?1), and trisodium citrate (50 mmol L^?1) as chelating agent. Soil was spiked at two different pollutant concentrations (1,000–10,000 mg diesel kg^?1 soil). Higher total petroleum hydrocarbon (TPH) removal efficiencies were obtained (up to 75 %) after the treatment in the absence of the chelant due to the low pH obtained in this case. In the presence of chelant, the TPH conversion obtained was lower because both higher pH is obtained and chelant competes with diesel for the oxidant. On the other hand, at neutral pH, the lifetime of the oxidant was increased. Fatty acid methyl esters (FAMEs) are easier to remove than diesel aliphatic hydrocarbons from the blend. An important decrease of the aqueous phase toxicity was observed after the modified Fenton reaction, supporting that nontoxic by-products were released to the aqueous phase during the treatment.     

Degradation of PAHs in soil by Lasiodiplodia theobromae and enhanced benzo[a]pyrene degradation by the addition of Tween-80

Benzo[a]pyrene (BaP), a five-ring polycyclic aromatic hydrocarbon (PAH), which has carcinogenic potency, is highly recalcitrant and resistant to microbial degradation. A novel fungus, Lasiodiplodia theobromae (L. theobromae), which can degrade BaP as a sole carbon source in liquid, was isolated in our laboratory. To prompt the further application of L. theobromae in remediation of sites polluted by BaP and other PAHs, the present study was targeted toward the removal of BaP and PAHs from soil by L. theobromae. The degradation of BaP by L. theobromae was studied using a soil spiked with 50 mg/kg BaP. L. theobromae could remove 32.1 % of the BaP after 35 days of cultivation. Phenanthrene (PHE) inhibited BaP degradation as a competitive substrate. The tested surfactants enhanced BaP degradation in soil by different extents, and a removal rate of 92.1 % was achieved at a Tween-80 (TW-80) concentration of 5 g/kg. It was revealed that TW-80 could not only enhance BaP bioavailability by increasing its aqueous solubility and decreasing the size of its colloid particles but also increase enzyme secretion from L. theobromae and the population of L. theobromae. Moreover, ergosterol content together with the biomass C indicated the increase in L. theobromae biomass during the BaP biodegradation process in soils. Finally, a soil from a historically PAH-contaminated field at Beijing Coking Plant in China was tested to assess the feasibility of applying L. theobromae in the remediation of polluted sites. The total removal rate of PAHs by L. theobromae was 53.3 %, which is 13.1 % higher than that by Phanerochaete chrysosporium (P. chrysosporium), an effective PAH degrader. The addition of TW-80 to the field soil further enhanced PAH degradation to 73.2 %. Hence, L. theobromae is a promising novel strain to be implemented in the remediation of soil polluted by PAHs.     

Effect of a cationic surfactant on the volatilization of PAHs from soil

Purpose

Cationic surfactants are common in soils because of their use in daily cosmetic and cleaning products, and their use as a soil amendment for the mitigation and remediation of organic contaminated soils has been proposed. Such surfactant may affect the transfer and fate of organic contaminants in the environment. This study investigated the effect of a cationic surfactant, dodecylpyridinium bromide (DDPB), on the volatilization of polycyclic aromatic hydrocarbons (PAHs) from a paddy soil.

Materials and methods

The volatilization of PAHs from moist soil amended with different concentrations of DDPB was tested in an open system. The specific effects of DDPB on the liquid?Cvapor and solid?Cvapor equilibriums of PAHs were separately investigated in closed systems by headspace analysis.

Results and discussion

DDPB affects both liquid?Cvapor and solid?Cvapor processes of PAHs in soil. At DDPB concentrations below the critical micelle concentration (CMC), movement of PAHs from the bulk solution to the gas?Cliquid interface appeared to be facilitated by interaction between PAHs and the surfactant monomers adsorbed at the gas?Cliquid interface, promoting the volatilization of PAHs from solution. However, when DDPB was greater than the CMC, volatilization was inhibited due to the solubilization of PAHs by micelles. On the other hand, the formation of sorbed surfactant significantly inhibited the solid?Cvapor volatilization of PAHs.

Conclusions

The overall effect of the two simultaneous effects of DDPB on liquid?Cvapor and solid?Cvapor processes was a decreased volatilization loss of PAHs from soil. Inhibition of PAH volatilization was more significant for the soil with a lower moisture content.     

A multi-process phytoremediation system for removal of polycyclic aromatic hydrocarbons from contaminated soils

To improve phytoremediation processes, multiple techniques that comprise different aspects of contaminant removal from soils have been combined. Using creosote as a test contaminant, a multi-process phytoremediation system composed of physical (volatilization), photochemical (photooxidation) and microbial remediation, and phytoremediation (plant-assisted remediation) processes was developed. The techniques applied to realize these processes were land-farming (aeration and light exposure), introduction of contaminant degrading bacteria, plant growth promoting rhizobacteria (PGPR), and plant growth of contaminant-tolerant tall fescue (Festuca arundinacea). Over a 4-month period, the average efficiency of removal of 16 priority PAHs by the multi-process remediation system was twice that of land-farming, 50% more than bioremediation alone, and 45% more than phytoremediation by itself. Importantly, the multi-process system was capable of removing most of the highly hydrophobic, soil-bound PAHs from soil. The key elements for successful phytoremediation were the use of plant species that have the ability to proliferate in the presence of high levels of contaminants and strains of PGPR that increase plant tolerance to contaminants and accelerate plant growth in heavily contaminated soils. The synergistic use of these approaches resulted in rapid and massive biomass accumulation of plant tissue in contaminated soil, putatively providing more active metabolic processes, leading to more rapid and more complete removal of PAHs.     

Electrokinetic remediation of a Cu contaminated red soil by conditioning catholyte pH with different enhancing chemical reagents

The effect of enhancement reagents on the efficiency of electrokinetic remediation of Cu contaminated red soil is evaluated. The enhancement agents were a mix of organic acids, including lactic acid+NaOH, HAc-NaAc and HAc-NaAc+EDTA. The soil was prepared to an initial Cu concentration of 438 mgkg(-1) by incubating the soil with CuSO4 solution in a flooded condition for 1 month. Sequential extraction showed that Cu was partitioned in the soil as follows: 195 mgkg(-1) as water soluble and exchangeable, 71 mgkg(-1) as carbonate bound and 105 mgkg(-1) as Fe and Mn oxides. The results indicate that neutralizing the catholyte pH maintains a lower soil pH compared to that without electrokinetic treatment. The electric currents varied depending upon the conditioning solutions and increased with an increasing applied voltage potential. The electroosmotic flow rate changed significantly when different conditioning enhancing reagents were used. It was observed that lactic acid+NaOH treatments resulted in higher soil electric conductivities than HAc-NaAc and HAc-NaAc+EDTA treatments. Ultimately, enhancement by lactic acid+NaOH resulted in highest removal efficiency (81% Cu removal) from the red soil. The presence of EDTA did not enhance Cu removal efficiencies from the red soil, because EDTA complexed with Cu to form negatively charge complexes, which slowly migrated toward the anode chamber retarding Cu2+ transport towards the cathode.     

植物混种原位修复多环芳烃污染农田土壤

通过比较实验前后土壤微生物主要类群数量、PAHs降解菌数量、土壤PAHs含量和植物不同部位PAHs含量变化,评价植物单种和混种野外原位修复多环芳烃(PAHs)污染农田土壤的效果。结果显示,150 d天生长期内,黑麦草/小麦混种及黑麦草/蚕豆混种修复效果最好,对土壤PAHs总量的降解率分别达到了59.4%和64.8%。同时,这2个混种处理土壤细菌、真菌和PAHs降解菌数量分别显著高于相应的小麦、蚕豆和黑麦草单种处理。植物不同部位PAHs含量高低次序为根部>茎叶≈籽粒。混种模式下,蚕豆和小麦不同部位PAHs含量比单种模式的不同程度降低,特别是籽粒部。植物混种模式不仅显著提高了土壤PAHs的降解率,还降低了农作物体内PAHs含量,实现了边生产边修复,在污染农田土壤修复领域有着广阔的应用前景。     

Lability of polycyclic aromatic hydrocarbons in the rhizosphere

Remediation of soils containing high concentrations of polycyclic aromatic hydrocarbons (PAHs) seldom results in complete removal of contaminants, but residual toxicity often is reduced. In this study, soil from a former manufactured gas plant site was treated for 12 months by phytoremediation and then tested for total PAHs, Tenax-TA extractable ("labile") PAHs, aqueous soluble PAHs (PAH(wp)) , and biotoxicity assessed by earthworms survival, nematode mortality, emergence of lettuce seedlings, and microbial respiration. Prior to phytoremediation, the soil had toxic impacts on all bioassays (except the nematodes), and 12 months of remediation decreased this response. Change in labile PAHs was a predictor for change in total PAH for 3- and 4-ring compounds but not for the 5- and 6-ring. Decreases in labile PAHs were correlated (r(2)>or=0.80) with toxicity in the bioassays except microbial respiration. PAH(wp) was correlated only with nematode toxicity prior to remediation but with none of the tests after remediation. Total PAHs were not correlated with any of the bioassay tests. Tenax-TA appears to have potential for predicting residual toxicity in remediated soils and is superior to total concentrations for that application.     

Effect of pH control at the anode for the electrokinetic removal of phenanthrene from kaolin soil

Polycyclic aromatic hydrocarbon (PAH)-contaminated soils exist at numerous sites, and these sites may threaten public health and the environment because many PAH compounds are toxic, mutagenic, and/or carcinogenic. PAHs are also hydrophobic and persistent, so conventional remediation methods are often costly or inefficient, especially when the contaminants are present in low permeability and/or organic soils. An innovative technique, electrokinetically enhanced in situ flushing, has the potential to increase soil-solution-contaminant interaction and PAH removal efficiency for low permeability soils; however, the electrolysis reaction at the anode may adversely affect the remediation of low acid buffering capacity soils, such as kaolin. Therefore, the objective of this study was to improve the remediation of low acid buffering soils by controlling the pH at the anode to counteract the electrolysis reaction. Six bench-scale electrokinetic experiments were conducted, where each test employed one of three different flushing solutions, deionized water, a surfactant, or a cosolvent. For each of these solutions, tests were performed with and without a 0.01 M NaOH solution at the anode to control the pH. The test using deionized water with pH control generated a higher electroosmotic flow than the equivalent test performed without pH control, but the electroosmotic flow difference between the surfactant and cosolvent tests with and without pH control was minor compared to that observed with the deionized water tests. Controlling the pH was beneficial for increasing contaminant solubilization and migration from the soil region adjacent to the anode, but the high contaminant concentrations that resulted in the middle or cathode soil regions indicates that subsequent changes in the soil and/or solution chemistry caused contaminant deposition and low overall contaminant removal efficiency.     

Removal of PCBs in contaminated soils by means of chemical reduction and advanced oxidation processes

Although the chemical reduction and advanced oxidation processes have been widely used individually, very few studies have assessed the combined reduction/oxidation approach for soil remediation. In the present study, experiments were performed in spiked sand and historically contaminated soil by using four synthetic nanoparticles (Fe⁰, Fe/Ni, Fe₃O₄, Fe_3???x Ni _x O₄). These nanoparticles were tested firstly for reductive transformation of polychlorinated biphenyls (PCBs) and then employed as catalysts to promote chemical oxidation reactions (H₂O₂ or persulfate). Obtained results indicated that bimetallic nanoparticles Fe/Ni showed the highest efficiency in reduction of PCB28 and PCB118 in spiked sand (97 and 79 %, respectively), whereas magnetite (Fe₃O₄) exhibited a high catalytic stability during the combined reduction/oxidation approach. In chemical oxidation, persulfate showed higher PCB degradation extent than hydrogen peroxide. As expected, the degradation efficiency was found to be limited in historically contaminated soil, where only Fe⁰ and Fe/Ni particles exhibited reductive capability towards PCBs (13 and 18 %). In oxidation step, the highest degradation extents were obtained in presence of Fe⁰ and Fe/Ni (18–19 %). The increase in particle and oxidant doses improved the efficiency of treatment, but overall degradation extents did not exceed 30 %, suggesting that only a small part of PCBs in soil was available for reaction with catalyst and/or oxidant. The use of organic solvent or cyclodextrin to improve the PCB availability in soil did not enhance degradation efficiency, underscoring the strong impact of soil matrix. Moreover, a better PCB degradation was observed in sand spiked with extractable organic matter separated from contaminated soil. In contrast to fractions with higher particle size (250–500 and <500 μm), no PCB degradation was observed in the finest fraction (≤250 μm) having higher organic matter content. These findings may have important practical implications to promote successively reduction and oxidation reactions in soils and understand the impact of soil properties on remediation performance.