首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 109 毫秒
1.
不同态二氧化钛处理模拟印染废水的研究   总被引:3,自引:2,他引:1  
以普通载玻片为基底材料,负载态和悬浮态的纳米二氧化钛/普通二氧化钛被用于处理甲基红模拟印染废水,实验结果表明:纳米二氧化钛的脱色效果明显优于普通的二氧化钛,适当增加负载量和处理时间,负载态的处理效果与悬浮态相当。首次提出了由光源决定的纳米光催化活性激发理论,解释了不同光源辐照时脱色率变化曲线差异的问题,并发现纳米TiO2光催化氧化模拟印染废水的脱色反应,主要由吸附过程控制的表面反应机理;150 mL模拟印染废水中,加入3块纳米TiO2负载量1 mg/cm2的普通载玻片,3~5 mL ClO2或H2O2,紫外光照60 min后,脱色率达到99.2%。  相似文献   

2.
利用无机溶液对废液晶显示屏的玻璃基板回收工艺作了初步的探索,根据回收处理的难易,简单地将废弃液晶显示屏分为3类:含树脂黑色矩阵膜的上层玻璃基板可以采用氢氧化钠直接浸泡处理、含铬黑矩阵膜的上层玻璃基板和下层玻璃基板可以先用氢氧化钠溶液浸泡去除偏光片,再用氢氟酸溶液浸泡处理。结果表明,利用无机溶液处理可以较快得到干净的玻璃基板,而且工艺简单、成本低。  相似文献   

3.
以光催化降解苯酚为探针反应,通过正交实验,系统研究了胶液配比、涂覆次数和焙烧温度等条件对以溶胶-凝胶法分别在普通钠钙玻璃和磨砂玻璃上制备TiO2光催化性能的影响,并利用环境扫描电镜(ESEM)对TiO2催化膜形貌进行了分析。研究表明,在普通钠钙玻璃片上负载TiO2催化膜的影响因素主次顺序为:硝酸体积〉涂覆次数〉焙烧温度〉V乙醇∶V酞酸丁酯,在选定实验条件下的最优条件为:涂覆次数为4次;焙烧温度=450℃;V乙醇∶V酞酸丁酯∶V硝酸(1∶4):V水=400∶40∶1∶4。在磨砂玻璃片上负载TiO2催化膜的的影响因素主次顺序为:涂覆次数〉硝酸体积〉焙烧温度〉V乙醇:V酞酸丁酯,在选定实验条件下的最优条件为:涂覆次数为4次;焙烧温度=500℃;V乙醇∶V酞酸丁酯∶V硝酸(1∶4)∶V水=400∶40∶2∶4。通过扫描电镜可以观察到在普通钠钙玻璃片和磨砂玻璃片表面均附着一层白色的TiO2薄膜,颗粒粒径在100 nm左右。磨砂玻璃比普通钠钙玻璃负载更多的催化剂,磨砂玻璃基TiO2活性更高。磨砂玻璃是一种非常有前景的TiO2催化剂载体材料。  相似文献   

4.
The performance of Teflon-coated glass fiber filter media (Pallflex Emfab TX40) is evaluated for particulate matter (PM) sampling of residential wood heating devices in a dilution tunnel. Thirty samples of varying duration and PM loading and concentration were collected from an U.S. Environmental Protection Agency (EPA) Method 28 dilution tunnel using dual Method 5G sample trains with untreated glass fiber and Emfab filters. Filters were weighed soon after the end of sampling and again the next day after equilibration at 35% relative humidity (RH). PM concentrations from both types of filters agreed very well with 1-day equilibration, demonstrating that Emfab filters are appropriate for use in measuring PM from residential wood burning appliances in a dilution tunnel and have performance equal to or better than the glass fiber filter media. Agreement between filter media without equilibration was erratic, with PM from glass fiber filter samples varying from slightly less than the Emfab samples to as much as 2.8 times higher. Some of the glass fiber filters lost substantial mass with equilibration, with the highest percent loss at lower filter mass loadings. Mass loss for Emfab samples was a small percentage of the mass and very consistent across the range of mass loadings. Taken together, these results may indicate water uptake on the glass fiber media that is readily removed with 1-day equilibration at moderate RH conditions.

Implications: EPA regulations now allow the use of either glass fiber or Teflon filter media for wood appliance PM emission testing. Teflon filter media minimizes the potential for acid-gas PM artifacts on glass fiber filters; this is important as EPA moves toward the use of locally sourced cordwood for testing that may have higher sulfur content. This work demonstrates that the use of Teflon-coated glass fiber filters can give similar PM measurement results to glass fiber filters after 1 day of equilibration. With no equilibration, measured PM from glass fiber filters was usually higher than from Teflon-coated glass fiber filters.  相似文献   


5.
Photocatalytic activity of TiO2 films grown on different substrates   总被引:8,自引:0,他引:8  
Ma Y  Qiu JB  Cao YA  Guan ZS  Yao JN 《Chemosphere》2001,44(5):1087-1092
Titanium dioxide films were prepared on glass, indium-tin oxide (ITO) glass and p-type monocrystalline silicon and studied for the photocatalytic degradation of rhodamine B in an aqueous medium. Raman, AFM, and XPS spectroscopic investigations of these films indicated that microstructure of titanium oxide films were greatly affected by the substrate materials. Rutile was confirmed to be easily formed on the surface of ITO glass, and TiO2 tended to grow as closely packed particles that were elongated strips with an average size of 20 nm, and had lovely contrast with the perfectly round particles grown on p-type monocrystalline silicon. Charge transfer between the film and silicon substrate was verified by surface photovoltage spectra. This may be the real reason why the films grown on ITO glass and silicon substrates exhibit higher photocatalytic reactivity than the film on glass substrate. Moreover, the different surface properties also seem to be responsible for the different activity.  相似文献   

6.
Glass ceramics were prepared from mixtures of wastes generated from refining of waste glass and semiconductor industrial wastewater sludge. The aim is then indeed to study the possible use and effects of integrating calcium fluoride (CaF2) as present in semiconductor wastewater sludge in the silica (glass) melts. CaF2 sludge was blended with a conditioner according to characteristics of the target. Calcium oxide-silicon dioxide-aluminum oxide system glass ceramics have relatively high melting points. Addition of CaF2 sludge to fluxes can significantly reduce the melting point and hence improve the kinetics of the reactions. CaF2 sludge and waste glass were co-melted in various ratios to elucidate their interactions at various heating temperatures. The results indicate that the lowest melting temperature was 1163 degrees C, obtained for the CaF2 sludge-waste glass mixture at a ratio 6:4 (wt:wt), which is significantly lower than that of CaF2 sludge (1378 degrees C). The benefits of using melting to dispose of sludge are the reduction of waste and the fixation of heavy metals. Heat treatment was used to convert the obtained glass into glass ceramics. Heavy metal leaching tests revealed that melting conditions lowered the heavy metal concentrations in the leachate to an order of magnitude lower than that in the sludge. Consequently, industrial sludge can be safely used as a fine aggregate material for a potentially wide range of construction applications.  相似文献   

7.
以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3+作为掺杂改性离子,形成了负载TiO2/Fe^3+的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365-250 W光源照射下,pH为3-5,O2通入量1.0 L/(min.L),反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。  相似文献   

8.
以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3+作为掺杂改性离子,形成了负载TiO2/Fe3+的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365~250 W光源照射下,pH为3~5,O2通入量1.0 L/(min.L),反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。  相似文献   

9.
在自行设计制备的真空热解炉中进行了废印制线路板的热解实验,得到固体、液体和气体产物。着重研究了热解固体渣中金属铜和非金属玻璃纤维的物理分选、热解固体渣分析及有氧煅烧对玻璃纤维纯度的影响。结果表明,物理分选效率很高,金属铜的回收率和纯度接近100%;热解固体渣含30.35%的铜、56.21%的玻璃纤维和13.45%的炭黑;有氧煅烧去除炭黑可得到高纯度的玻璃纤维。  相似文献   

10.
This work discusses the preparation and characterizations of glass hollow fiber membranes prepared using zeolite-5A as a starting material. Zeolite was formed into a hollow fiber configuration using the phase inversion technique. It was later sintered at high temperatures to burn off organic materials and change the zeolite into glass membrane. A preliminary study, that used thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared (FTIR), confirmed that zeolite used in this study changed to glass at temperatures above 1000 °C. The glass hollow fiber membranes prepared using the phase inversion technique has three different microstructures, namely (i) sandwich-like structure that originates from inner layer, (ii) sandwich-like that originates from outer layer, and (iii) symmetric sponge like. These variations were influenced by zeolite weight loading and the flow rate of water used to form the lumen. The separation performances of the glass hollow fiber membrane were studied using the pure water permeability and the rejection test of bovine serum albumin (BSA). The glass hollow fiber membrane prepared from using 48 wt% zeolite loading and bore fluid with 9 mL min?1 flow rate has the highest BSA rejection of 85% with the water permeability of 0.7 L m?2 h?1 bar?1. The results showed that the separation performance of glass hollow fiber membranes was in the ultrafiltration range, enabled the retention of solutes with molecular sizes larger than 67 kDa such as milk proteins, endotoxin pyrogen, virus, and colloidal silica.  相似文献   

11.
机械活化对CRT锥玻璃浸出动力学的影响   总被引:1,自引:0,他引:1  
通过研究CRT锥玻璃经机械活化后在硝酸溶液体系中浸出反应动力学规律,考察了机械球磨转速、浸出温度以及硝酸初始浓度对锥玻璃中铅的浸出效果影响。研究结果表明,锥玻璃经机械活化预处理后,反应活性显著增强,锥玻璃中铅浸出率大幅度提高。浸出反应的表观活化能和反应级数由109.4 kJ/mol和0.79降至54.3 kJ/mol和0.51。  相似文献   

12.
利用废CRT屏玻璃为原料制备泡沫玻璃   总被引:3,自引:1,他引:2  
以废阴极射线管(CRT)屏玻璃为主要原料,碳黑为起泡剂,采用粉末烧结法制备了低密度保温泡沫玻璃。通过扫描电镜(SEM)、导热系数测定仪等分析手段,研究了起泡剂的用量、发泡温度和发泡时间对泡沫玻璃泡径、密度、热学性能以及机械力学性能的影响。结果表明,在相同烧制工艺条件下,随起泡剂掺加量增加,烧制所得的泡沫玻璃密度成"V"型变化;当其掺加量为0.20%时,泡沫玻璃在密度、孔径分布以及力学性能上均达到最佳。随着发泡温度的提高和发泡时间的延长,密度会逐渐减小,泡沫玻璃的气泡会逐渐增大,以致产生连通现象。当发泡温度为820℃、发泡时间为30min时烧制的泡沫玻璃密度为0.180 g/cm3,导热系数为0.0695 W/(m.K)。  相似文献   

13.
Background, aim, and scope  The first step in the restoration of a medieval stained glass window is the evaluation of its degree of degradation. This implies the study of the chemical composition of the stained glass as well as the new mineral phases developed on its surface (patinas). Patinas are clearly related to glass composition, time, environmental conditions, microenvironments developed in local zones, bioactivity, physical and chemical factors, etc. This study was carried out on patinas developed in selected Na-rich stained glass of the Santa Maria de Pedralbes Monastery (Barcelona, Spain). The location of this monument in the city (about 5 km from the shoreline and close to the Collserola hill flank) helped to determine the environmental conditions in which patinas developed. The aim of our study was to characterize the patinas formed on the surface of the selected glass of this monastery in order to understand the role of the chemical composition of the original glass (Na-rich) as well as the environmental conditions in which they developed. Materials and methods  Powdered samples of two different color-type patinas (ochre-orange and brownish) were collected in the external and internal parts of the stained glass windows of the Prebystery and Chapter House of the Pedralbes Monastery by using a precision (odontological) drill. These patinas were subsequently analyzed by X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). Results  XRD analyses evidenced the presence of sulfates (gypsum and thenardite), calcite, Ca-oxalates (whewellite and weddellite), and quartz forming part of the patinas. Although these mineral phases can be found in both color-type patinas, whewellite and thenardite are more common in the ochre-orange patinas. The results obtained were validated by the FTIR measurements. It has been observed, when thenardite is present, that gypsum occurs as traces. Thenardite is in most of the cases associated with whewellite and mainly occurs in the internal parts of the glass. In contrast, weddellite is limited to the absence of thenardite and whewellite and to the external parts of the stained glass. Quartz is present in all the patinas independent of their location and color. Calcite also occurs in many samples. It appears in both color-type patinas and, in some cases, is associated to the presence of weddellite but not to whewellite and/or thenardite. Discussion  Glass composition together with environmental conditions and location of the patinas (internal or external parts of the stained glass window), as well as the provenance of the glass within the monastery, are the main factors that define the development of the new mineral phases. Moreover, the action of microorganisms, when present, can also strongly influence the development of some mineral phases. For example, the formation of calcite in the external parts of the stained glass (associated with the presence of oxalates) is related to the action of microorganisms. When calcite is formed in the internal parts of the glass and it is not associated with the presence of Ca-oxalates, an inorganic origin can be invoked. The presence of weddellite requires a very humid microenvironment with very little exposure to sunlight. In fact, this mineral phase has only been observed in the external parts of some glass located in the humid and shady side of the monastery. Whewellite (which only appears in the internal parts) needs a low degree of relative humidity. It has been observed that sulfur precipitating in basically one mineral phase (thenardite or gypsum) depends on the microenvironmental conditions of the moment and the glass composition. When thenardite occurs, it can be maintained that the original glass is of Na composition. The occurrence of quartz in all samples is interpreted as being due to the deposition of atmospheric particulate matter. The color of the patinas can be originated by different processes (presence of carotenes, organic pigmentation, atmospheric contamination, etc.). Conclusions  In the case of moderately weathered stained glass windows, the combination of XRD and FTIR techniques is very useful to obtain a fast preliminary evaluation of the degree of weathering of a stained glass window. The presence of specific mineral phases in the patina (e.g., thenardite) confirms the Na composition of the original stained glass. This is important since Na-rich glass underwent a lesser degree of weathering than K- or K-Ca-rich glass. However, their absence cannot preclude other possibilities. It has been extensively evidenced through time that environmental conditions play an important role on the formation of the different mineral phases which form part of the patinas. Recommendations and perspectives  The first step in the restoration of a stained glass window is the evaluation of the degree of deterioration of the glass. This evaluation includes a chemical analysis of the glass as well as a characterization of the patinas developed on their surfaces. The obtained results will be essential in order to define the best restoration practices to be followed.  相似文献   

14.
废弃等离子显示屏玻璃中重金属化学形态分布   总被引:1,自引:0,他引:1  
通过BCR3步和BCR4步连续提取法,对等离子体显示屏玻璃中重金属的化学形态进行研究。结果表明,BCR3步连续提取法对废弃等离子体显示屏玻璃中重金属的提取比BCR4步连续提取法更稳定。废弃等离子体显示屏玻璃中Zn、Cu和Ag化学形态分布存在差异。BCR3步和BCR4步连续提取法均认为Ag以残渣态为主要赋存形态,对环境影响比较小;Cu的可交换与弱酸可溶态或交换态和碳酸盐结合态含量较少,潜在的环境风险也比较小;BCR3步和BCR4步连续提取法对Zn的形态分布结果评价不一致,BCR3步连续提取法表明Zn主要以可交换与弱酸可溶态为主,对环境影响较大,而BCR4步连续提取法结果认为Zn是以铁锰氧化态为主要存在形态。  相似文献   

15.
Photodegradation of alphacypermethrin ((RS)-alpha cyano-3-phenoxy benzyl (1RS) cis-3-(2,2,dichlorovinyl)-2,2-dimethyl cyclopropane carboxylate) was studied as a thin film on glass surface and on black and red soil surfaces. A number of photoproducts from glass surfaces have been isolated, characterized and identified by gas chromatography-mass spectroscopy (GC-MS). However, only two of them viz. 3-phenoxy benzyl alcohol and [2,2-dichlorovinyl-3(2,2,dimethyl) cyclopropane carboxylate] could be identified from both the soil. Rate of photodegradation on glass and soil surface under UV and sunlight followed first order kinetics with significant correlation coefficients. The rate of photodegradation was greater on black than on red soil.  相似文献   

16.
To prevent the soiling of glass window used in the built environment, the use TiO2 coated products appears an important application matter. To test the cleaning efficiency and the sustainability of self-cleaning glass, a field experiment was conducted under real life condition, on a site representative of the background urban pollution. Samples of float glass, used as reference, and commercialized TiO2 coated glasses were exposed to dry and wet atmospheric deposition during two years. The crossed optical, chemical and microscopic evaluations performed, after withdrawal, allowed highlighting a sensible difference between the reference and the self-cleaning substrate in terms of accumulation, nature, abundance and geometry of the deposit. This experiment conducted in real site emphasized on the efficacy of self-cleaning glass to reduce the maintenance cost.  相似文献   

17.
Previous attempts to measure heavy metals in air are discussed with particular reference to lead. A polarographic method was developed for lead in air samples taken on glass fiber sheet. Using this method, the distribution of lead across the glass fiber sheet was investigated, and within experimental error, found to be uniform. Air samples from 18 Ontario cities, previously analyzed for benzo [a]pyrene content were analyzed.  相似文献   

18.

The environmental impact of waste glass (WG) is one of the major challenges crippling sustainable waste management and mitigation. Reclamation of recycled materials from waste glass remains a tedious task amidst complex technological approaches. The challenge as seen in the global containment measures increase the proportion of waste glass and minimize the existing capacity of landfill space. In many works, findings have shown how best to minimize the impact of waste glass as evidenced in their inclusion as building materials such as cement, mortars, concretes and blocks. The concept of this paper is to appraise previous studies carried out on the use of waste glass as key contributing factor in structural building. The scope of this paper will be broaden to include various successes recorded in the evolution of concrete mixtures containing different proportion of recycle glass. Part of the setbacks noted in the inclusion of these recycled materials as matrix, filler or fibre are also reported in this paper. Also discussed is the durability of glass materials in varying conglomerate involving cement in reinforcement of building and structures. Thermal insulating properties of recycled glass are also considered in this work where considerable energy is saved due to their low thermal conductivity. Based on the analysis of various studies and other factors considered in this paper, it is established that recycled glass materials can be accommodated in structural buildings, while continuous research is necessary to adapt waste glass to high pH value of Portland cement.

  相似文献   

19.
In the 1970s, a large ambulatory of the National Tile Museum, Lisbon, was closed with glass panes on both ground and first floor. Although this design was meant to protect the museum collection from ambient air pollutants, small openings between the glass panes remain, creating a semi-enclosed corridor. The effects of the glass panes on the indoor air quality were evaluated in a comparative study by monitoring the airborne particle concentration and the extent of particle deposition at the enclosed corridor as well as inside the museum building. Comparison of the indoor/outdoor ratio of airborne particle concentration demonstrated a high natural ventilation rate in the enclosed corridor as well as inside the museum building. PM10 deposition velocities on vertical surfaces were estimated in the order of 3?×?10?4 m s?1 for both indoor locations. Also, the deposition rates of dark-coloured and black particles in specific were very similar at both indoor locations, causing visual degradation. The effectiveness of the glass panes in protecting the museum collection is discussed.  相似文献   

20.

Photodegradation of alphacypermethrin ((RS)-α cyano-3-phenoxy benzyl (1RS) cis-3-(2,2,dichlorovinyl)-2,2-dimethyl cyclopropane carboxylate) was studied as a thin film on glass surface and on black and red soil surfaces. A number of photoproducts from glass surfaces have been isolated, characterized and identified by gas chromatography-mass spectroscopy (GC-MS). However, only two of them viz. 3-phenoxy benzyl alcohol and [2,2-dichlorovinyl-3(2,2,dimethyl) cyclopropane carboxylate] could be identified from both the soil. Rate of photodegradation on glass and soil surface under UV and sunlight followed first order kinetics with significant correlation coefficients. The rate of photodegradation was greater on black than on red soil.

  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号