流化床O2/CO2气氛下添加SiO2对燃煤PM2.5的控制

采用小型流化床研究了在O2/CO2气氛下添加SiO2对PM2.5(空气动力学直径小于2.5 μm的颗粒物)的控制,试验在1123 K、O2/CO2气氛下进行,并采用荷电低压撞击器(ELPI)采集和分析燃烧后的PM2.5.结果表明,添加SiO2是燃烧过程中影响PM2.5生成的重要因素.添加SiO2后,生成PM1的质量浓度均降低,而PM1-2.5的质量浓度均略有增加;PM2.5质量粒径分布均呈双峰分布,峰值分别出现在0.2 μm和2.0μm左右.随着SiO2添加量的增加,PM2.5中的S、K、Na、Cu和Pb元素的含量呈减少的趋势;随着颗粒粒径减小,S、K、Na、Cu和Pb元素的含量有增高的趋势.     

CH4/H2O/H2辅助热催化CO2转化机制

随着热化学技术及相关反应机制认知的不断进步，二氧化碳回收转化为高附加值燃料或其他化工产品的清洁能源技术正逐步走向成熟。同时，因社会工业进步及人类生产活动急剧增加了大气中的二氧化碳浓度，且已远超地球正常发展的浓度阈值，这使得基于二氧化碳转化的零碳高效可再生清洁能源技术成为世界各国为应对全球能源与环境问题亟待实现的关键技术。鉴于二氧化碳热催化转化的基本原理、关键材料和反应系统的相关研究对于推动该技术的工业化进程有着至关重要的作用，本文报道了二氧化碳热催化转化机制相关的最新进展，重点阐述了对热催化过程具有辅助作用的活性气体(包括H₂O、CH₄和H₂)在实现高水平二氧化碳回收转换与高效合成气生产方面的催化机制，其核心体现在优化的反应动力学与温和条件下的热力学优势。     

UV/H2O2/

以     

Unraveling SO2-tolerant mechanism over Fe2（SO4）3/TiO2 catalysts for NOx reduction

Developing low-temperature SO₂-tolerant catalysts for the selective catalytic reduction of NO_x is still a challenging task. The sulfation of active metal oxides and deposition of ammonium bisulfate deactivate catalysts, due to the difficult decomposition of the as-formed sulfate species at low temperatures（<300 °C）. In recent years, metal sulfate catalysts have attracted increasing attention owing to their good catalytic activity and strong SO₂ tolerance at hi...     

SO2对掺杂KMnO4的K2CO3/Al2O3吸附剂脱碳性能影响

针对SO₂对吸附剂CO₂吸附性能的影响，该文采用溶胶-凝胶法制备氧化铝气凝胶载体，浸渍法制备吸附剂，通过固定床实验系统进行N₂低温吸附-脱附实验，研究了掺杂KMnO₄的K₂CO₃/Al₂O₃吸附剂CO₂吸附性能以及SO₂对吸附剂吸附性能的影响。利用Avrami模型计算吸附动力学，并结合吸附剂的孔隙和晶相结构变化分析吸附机理。结果表明：吸附实验最佳反应温度60℃，掺杂KMnO₄提高了K₂CO₃/Al₂O₃的CO₂吸附性能，吸附量提高0.13 mmol/g。在CO₂吸附实验中加入微量SO₂，掺杂KMnO₄后会减小烟气中SO₂对CO₂吸附...     

污泥与煤在CO2/O2及N2/O2气氛条件下的混燃特性分析

采集了广州具有代表性的市政污泥,利用热重法对单一污泥、煤及其混合样品在CO_2/O_2及N_2/O_2气氛条件下进行了TG(热重)实验,同时计算了污泥和煤的4个燃烧特性指数,获得了燃烧的动力学参数.实验结果表明,污泥燃烧有4个燃烧阶段,包括水分析出、挥发分析出与燃烧、固定碳的燃烧和无机盐类挥发分解,其中,挥发分析出与燃烧是污泥燃烧的主要阶段;煤掺烧污泥可以提高煤的着火性能.在CO_2/O_2及N_2/O_2燃烧气氛下,增加O_2浓度,污泥与煤混合样的热重曲线整体向低温区移动,微商热重曲线峰值增大,峰宽变小,燃烧性能增强.在CO_2/O_2气氛下,O_2浓度从30%增加到60%时,污泥的挥发分释放特性指数D、可燃性指数C、燃尽指数Cb、综合燃烧特性指数S分别增加了45%、12%、18%、6%.相同O_2浓度条件下,污泥与煤在CO_2/O_2气氛下的着火性能较N_2/O_2气氛滞后,最大峰值变小,高浓度的CO_2抑制其混合样的燃烧.采用Coats-Redfern方程计算得到3个燃烧阶段反应的动力学参数,其中,增加O_2浓度,污泥与煤混合样品的质量平均表观反应活化能Em减小,并且O_2浓度越高越有利于燃烧反应的进行.污泥与煤混合燃烧取n=2可以对挥发分燃烧与固定碳燃尽峰峰前与峰后的反应模型进行描述.     

O3、O3/H2O2、O3/H2O2/UV工艺降解炸药工业废水中RDX的试验研究

为了研究高级氧化技术对含黑索今(RDX)的炸药工业废水的处理效果,本文采用O3、O3/H2O2、O3/H2O2/UV 3种氧化工艺分别对废水中的RDX进行了降解试验,并对比分析了3种工艺的处理效果和机制。结果表明:O3/H2O2、O3/H2O2/UV工艺对RDX的去除率明显优于O3工艺;提高体系的pH值将有利于RDX的降解;随着RDX初始浓度的增加,RDX的去除率呈现下降趋势;投加H2O2和UV照射可提高臭氧的利用率,且O3/H2O2/UV工艺催化臭氧分解的能力比O3/H2O2工艺强。     

The selective catalytic reduction of NO over Ce0.3TiOx-supported metal oxide catalysts

A Ce_(0.3)TiO_xoxide carrier was synthesized via a sol–gel process,and Ce_(0.3)TiO_xsupported metal(M=Cd,Mn,Fe,W,Mo)oxide catalysts were prepared by the method of incipient-wetness impregnation.The catalysts were characterized by means of X-ray diffraction(XRD),Brunauer–Emmett–Teller(BET)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),Fourier transform infrared(FT–IR)spectroscopy,UV–Visdiffusereflectancespectroscopy(UV–VisDRS),and Temperature-programmed reduction with H_2(H_2-TPR).The catalytic activities for de-NO_(x )were evaluated by the NH_3-SCR reaction.Among all the catalysts tested,the 2 wt.%Cd/Ce_(0.3)TiO_xcatalyst exhibited the best NH_3-SCR performance,with a wide temperature window of 250–450°C for NO conversion above 90%.Moreover,the catalyst showed N_2 selectivity greater than 99%from 200 to 450°C.     

Synergistic effect of N- and F-codoping on the structure and photocatalytic performance of TiO2

Three types of TiO₂ nanostructures were synthesized via a facile hydrolysis method at 195 °C. Effects of the preparation method and doping with N and F on the crystal structure and photocatalytic performance of TiO₂ were investigated. The nanomaterials were characterized by X-ray diffraction, transmission electron microscopy, X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller porosimetry, ultraviolet–visible diffuse reflectance spectroscopy and fluorescent emission spectra. Their photo-catalytic activity was examined by the photodegradation of methylene blue in aqueous solution under both ultra-violet and visible light irradiation. The results show that nitrogen and fluorine co-doped anatase TiO₂ had the characteristics of a smaller crystalline size, broader light absorption spectrum and lower charge recombination than pure TiO₂. Most importantly, more efficient photocatalytic activity under both ultra-violet and visible light was observed. The obtained N–F-TiO₂ nanomaterial shows considerable potential for water treatment under sunlight irradiation.     

Visible light responsive N-F-codoped TiO2 photocatalysts for the degradation of 4-chlorophenol

Visible light responsive N-F-codoped TiO₂ photocatalysts exhibit a higher catalytic activity than N-doped TiO₂ for the degradation of 4-chlorophenol due to the synergistic effect of nonmetal elements.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

Triton X-100 induced cuboid-like BiVO4 microsphere with high photocatalytic performance

A highly active visible light-induced BiVO₄ photocatalyst was prepared by a simple co-precipitation method using ammonia solution as a pH adjustor and Triton X-100 (TX100) as a structure directing agent. The physical properties of the prepared BiVO₄ photocatalyst were investigated by several techniques such as X-ray diffractometer (XRD), Brunauer–Emmett–Teller (BET) surface area measurement, scanning electron microscopy (SEM), energy dispersive analysis (EDS), Fourier-transformed infrared spectroscopy (FT-IR), photoluminescence (PL), and UV–Vis diffused reflectance spectroscopy (DRS). XRD results revealed the existence of a monoclinic scheelite structure in both the unmodified and the modified samples. The TX100 played a crucial role to control the cuboid-like shape morphology of BiVO₄. The DRS results showed that the as-prepared cuboid BiVO₄ possessed enhanced visible light absorption range compared with that of the unmodified BiVO₄. The photocatalytic activity was evaluated via indigo carmine (IC) degradation under visible light irradiation. The modified BiVO₄ showed higher photocatalytic efficiency than the unmodified BiVO₄ and the commercial P25-TiO₂ which could be ascribed to the better charge separation efficiency.     

Photocatalytic parameters and kinetic study for degradation of dichlorophenol-indophenol (DCPIP) dye using highly active mesoporous TiO2 nanoparticles

Highly active mesoporous TiO_2 of about 6 nm crystal size and 280.7 m~2/g specific surface areas has been successfully synthesized via controlled hydrolysis of titanium butoxide at acidic medium. It was characterized by means of XRD(X-ray diffraction), SEM(scanning electron microscopy), TEM(transmission electron microscopy), FT-IR(Fourier transform infrared spectroscopy), TGA(thermogravimetric analysis), DSC(differential scanning calorimetry) and BET(Brunauer–Emmett–Teller) surface area. The degradation of dichlorophenol-indophenol(DCPIP) under ultraviolet(UV) light was studied to evaluate the photocatalytic activity of samples. The effects of different parameters and kinetics were investigated. Accordingly, a complete degradation of DCPIP dye was achieved by applying the optimal operational conditions of 1 g/L of catalyst, 10 mg/L of DCPIP, pH of 3 and the temperature at 25 ± 3°C after 3 min under UV irradiation. Meanwhile, the Langmuir–Hinshelwood kinetic model described the variations in pure photocatalytic branch in consistent with a first order power law model.The results proved that the prepared TiO_2 nanoparticle has a photocatalytic activity significantly better than Degussa P-25.     

Synthesis, characterization, and photocatalytic activity of porous La–N–co-doped TiO2 nanotubes for gaseous chlorobenzene oxidation

The photocatalytic oxidation of gaseous chlorobenzene(CB) by the 365 nm-induced photocatalyst La/N–Ti O2, synthesized via a sol–gel and hydrothermal method, was evaluated. Response surface methodology(RSM) was used to model and optimize the conditions for synthesis of the photocatalyst. The optimal photocatalyst was 1.2La/0.5N–Ti O2(0.5) and the effects of La/N on crystalline structure, particle morphology, surface element content, and other structural characteristics were investigated by XRD(X-ray diffraction), TEM(Transmission Electron Microscopy), FTIR(Fourier transform infrared spectroscopy), UV–vis(Ultraviolet–visible spectroscopy), and BET(Brunauer Emmett Teller). Greater surface area and smaller particle size were produced with the co-doped Ti O2 nanotubes than with reference Ti O2. The removal of CB was effective when performed using the synthesized photocatalyst,though it was less efficient at higher initial CB concentrations. Various modified Langmuir-Hinshelwood kinetic models involving the adsorption of chlorobenzene and water on different active sites were evaluated. Fitting results suggested that competitive adsorption caused by water molecules could not be neglected, especially for environments with high relative humidity. The reaction intermediates found after GC–MS(Gas chromatography–mass spectrometry) analysis indicated that most were soluble, low-toxicity, or both. The results demonstrated that the prepared photocatalyst had high activity for VOC(volatile organic compounds) conversion and may be used as a pretreatment prior to biopurification.     

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

Simulated-sunlight-activated photocatalysis of Methylene Blue using cerium-doped SiO2/TiO2 nanostructured fibers

Cerium-doped SiO₂/TiO₂ nanostructured fibers were fabricated by electrospinning technology. The prepared fibers were characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). Using the fibers as catalysts, photocatalytic degradation of Methylene Blue (MB) aqueous solution was carried out under simulated sunlight. The 0.2% Ce doping proved to be the optimal concentration for the doping of TiO₂/SiO₂, compared to other Ce-doped molar concentrations. The 0.2% Ce-doped SiO₂/TiO₂ fibers exhibited higher photocatalytic activity than industrial Degussa P25 and the samples doped with only Ce or SiO₂. The reasons for improving the photocatalytic activity were also discussed. Several operational parameters were studied, which showed that the photocatalytic efficiency of MB was influenced by parameters such as the initial dye concentration, the initial pH, inorganic anions, and so on. In addition, the influences of an electron acceptor and a radical scavenger suggested that OH was the dominant photooxidant during the photocatalytic process. The reuse evaluation of the fibers indicated that their photocatalytic activity had good stability.     

Synthesis,crystal structure,photodegradation kinetics and photocatalytic activity of novel photocatalyst ZnBiYO4

ZnBiYO₄ was synthesized by a solid-state reaction method for the first time. The structural and photocatalytic properties of ZnBiYO₄ were characterized by X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV–Vis diffuse reflectance. ZnBiYO₄ crystallized with a tetragonal spinel structure with space group I41/A. The lattice parameters for ZnBiYO₄ were a = b = 11.176479 Å and c = 10.014323 Å. The band gap of ZnBiYO₄ was estimated to be 1.58 eV. The photocatalytic activity of ZnBiYO₄ was assessed by photodegradation of methyl orange under visible light irradiation. The results showed that ZnBiYO₄ had higher catalytic activity compared with N-doped TiO₂ under the same experimental conditions using visible light irradiation. The photocatalytic degradation of methyl orange with ZnBiYO₄ or N-doped TiO₂ as catalyst followed first-order reaction kinetics, and the first-order rate constant was 0.01575 and 0.00416 min^− 1 for ZnBiYO₄ and N-doped TiO₂, respectively. After visible light irradiation for 220 min with ZnBiYO₄ as catalyst, complete removal and mineralization of methyl orange were observed. The reduction of total organic carbon, formation of inorganic products, SO₄^2 − and NO₃⁻, and evolution of CO₂ revealed the continuous mineralization of methyl orange during the photocatalytic process. The intermediate products were identified using liquid chromatography–mass spectrometry. The ZnBiYO₄/(visible light) photocatalysis system was found to be suitable for textile industry wastewater treatment and could be used to solve other environmental chemical pollution problems.