Power requirements and environmental impact of a pedelec. A case study based on real-life applications

This paper describes the methodologies to appraise the power requests and environmental analysis of an electrically assisted bicycle under real driving conditions, also containing regulations and technical-science-related aspects. For this purpose, in this study, the on-road test program of an electrically assisted bicycle was executed in the urban area of Naples on different test tracks, so a general assessment about its driving behavior under several driving conditions was performed. The power requirements in different typical riding situations were estimated by a procedure based on the experimental kinematic parameters that characterize the driving dynamics collected during the real-life applications. An environmental analysis was also performed, with a methodology that takes into account the environmental assessment of a moped by measuring the experimental moped exhaust emissions of the regulated pollutants. Starting from the results acquired during the different test samples, besides, an assessment of the electric traction offered by this pedelec on the driving comfort was evaluated for different riding situations.     

Trends in exhaust emissions from in-use Mexico City vehicles, 2000–2006. A remote sensing study

A remote sensing study was conducted in year 2006 in four locations of the Metropolitan Area of Mexico City (MAMC). Two of the sites were the same studied back by us in year 2000 and by others in year 1994. A database was compiled containing 11,289 valid measurements for the carbon monoxide (CO), total hydrocarbons (THC), and nitric oxide (NO) exhaust vehicles emissions. Valid measurements were binned for each pollutant by the vehicle specific power (between −5 and 20 kW tonne⁻¹) for the 2000 and 2006 databases. The mean average CO, THC, and NO emissions for year 2006 were determined to be 1.10 ± 0.18 vol.%, 299 ± 88.4 ppm, and 610 ± 115.0 ppm, respectively. Matching the vehicle driving patterns of the fleet measured in year 2000 with the emissions factors obtained in this work, allows estimating the trends in the exhaust emissions of vehicles in the MAMC. The adjusted results of the remote sensing study performed in year 2006 shows that the fleet has decrease 22% in CO and 17% in NO emissions, with small change in total hydrocarbons emissions. The improvements could be related with the introduction in year 2001 of vehicles that met tighter emissions standards, particularly for nitrogen oxides.     

Assessment of New Vehicles Emissions Certification Standards in the Metropolitan Area of Mexico City

Light duty gasoline vehicles account for most of CO hydrocarbons and NOx emissions at the Metropolitan Area of Mexico City (MAMC). In order to ameliorate air pollution from the beginning of 2001, Tier 1 emission standards became mandatory for all new model year sold in the country. Car manufacturers in Mexico do not guarantee the performance of their exhaust emissions systems for a given mileage. The purpose of this study was to assess whether the Tier 1 vehicles will stand the certification values for at least 162000 km with the regular fuel available at the MAMC. Mileage accumulation and deterioration show that certified carbon monoxide emissions will stand for the useful life of the vehicles but in the case of non-methane hydrocarbons will be shorter by 40%, and nitrogen oxides emissions above the standard will be reached at one third of the accumulated kilometers. The effect of gasoline sulfur content, on the current in use Tier 1 vehicles of the MAMC and the impact on the emissions inventory in year 2010 showed that 31000 extra tons of NOx could be added to the inventory caused by the failure of the vehicles to control this pollutant at the useful life of vehicles.     

Emissions of VOCs at Urban Petrol Retail Distribution Centres in India (Delhi and Mumbai)

Air pollution has assumed gigantic proportion killing almost half a million Asians every year. Urban pollution mainly comprises of emissions from buses, trucks, motorcycle other forms of motorized transport and its supporting activities. As Asia's cities continue to expand the number of vehicles have risen resulting in greater pollution. Fugitive emissions from retail distribution center in urban area constitute a major source. Petrol vapours escape during refueling adding pollutants like benzene, toluene, ethylbenzene and xylene to ambient air. This paper discusses a study on fugitive emissions of Volatile Organic Compounds (VOC) at some refueling station in two metropolitan cities of India, i.e., Mumbai and Delhi. Concentration of VOCs in ambient air at petrol retail distribution center is estimated by using TO-17 method. Concentration of benzene in ambient air in Delhi clearly shows the effect of intervention in use of petroleum and diesel fuel and shift to CNG. Chemical Mass Balance (CMB) model is used to estimate source contributions. At Delhi besides diesel combustion engines, refueling emissions are also major sources. At Mumbai evaporative emissions are found to contribute maximum to Total VOC (TVOC) concentration in ambient air.     

Profile of PAH in the Exhaust of Gasoline Driven Vehicles in Delhi

A preliminary study to determine the profile of PAHs in the exhaust of gasoline vehicles in Delhi was conducted. Three different types of vehicles (cars, autorickshaws and scooters) were selected with different age groups for sampling purpose. The concentration of Total PAHs (Σ₁₂PAHs) was found to be 27.27 ± 2.27, 28.61 ± 3.70 and 29.81 ± 3.57 mg/g in the exhaust of cars, auto- rickshaws (three wheelers) and two wheelers, respectively. The levels of PAHs were found to be high in scooter exhaust as compared to that of cars and autorickshaws. The total PAHs concentration in the present study was found to be higher as compared to other studies. Such a high concentration could be attributed to different parameters like the age of the vehicles, driving conditions, the fuel quality and the emission standards.     

Modelling of Motor Vehicle Fuel Consumption and Emissions Using a Power-Based Model

The performance of a power based fuel consumption and exhaust emissions model for spark ignition vehicles has been evaluated using a large Australian database derived from testing a wide range of in-use cars on a chassis dynamometer. It was also applied to results of on-road fuel consumption measurement using a "floating" car which was driven back and forth on hilly roadways in Sydney with a length of 8.6 km. The model is found to predict the fuel consumption well over the standard drive cycles and also for the floating car. Average exhaust emissions were also well predicted, but, as would be expected, vehicle-to-vehicle correlation is impossible due to the well-known high variability of emissions between nominally identical vehicles.     

Profile of PAHs in the Diesel Vehicle Exhaust in Delhi

A preliminary study to determine the profile of PAHs in the exhaust of diesel vehicles plying on Delhi roads was conducted. Two different types of diesel vehicles (buses and trucks) with different age groups were selected for sampling purpose. The concentration of Total PAHs (₁₂PAHs) was found to be 50.76 ± 6.62 and 57.72 ± 4.15 mg/g in the exhaust of buses and trucks, respectively. The levels of PAHs were found to be high in trucks as compared to that of buses. The total PAHs concentration in the present study was found to be higher as compared to other studies. Such a high concentration could be attributed to different parameters like the age of the vehicles, driving conditions, the fuel quality and the emission standards.     

Diurnal models of traffic-generated CO for Penang,Malaysia

Georgetown of Penang, an old city, is noted for its narrow streets. The existing traffic dispersal system is utterly inadequate to cope with the ever increasing number of cars and motorcycles on the road. The principal objective of this study is to build prediction models of CO to be employed as one of the planning tools in the future design of Penang urban traffic dispersal system. This study involves the monitoring of kerbside CO levels at selected sites and the fitting of hourly-averaged CO data to linear regression models incorporating the residual effect of CO emission due to traffic in the earlier periods and also different categories of vehicles. The best overall regression model appears to be the one based upon the total traffic count of motorcycles. This can be accounted for by the fact that the traffic counts of motorcycles and cars are highly correlated in most cases and that the emissions of CO from motorcycles are more readily detected as they travel closer to the kerb. The inclusion of residual CO in the models significantly improves the correlation coefficient from about 0.4 to about 0.7.     

The contribution of evaporative emissions from gasoline vehicles to the volatile organic compound inventory in Mexico City

The strategy for decreasing volatile organic compound emissions in Mexico has been focused much more on tailpipe emissions than on evaporative emissions, so there is very little information on the contribution of evaporative emissions to the total volatile organic compound inventory. We examined the magnitudes of exhaust and evaporative volatile organic compound emissions, and the species emitted, in a representative fleet of light-duty gasoline vehicles in the Metropolitan Area of Mexico City. The US “FTP-75” test protocol was used to estimate volatile organic compound emissions associated with diurnal evaporative losses, and when the engine is started and a journey begins. The amount and nature of the volatile organic compounds emitted under these conditions have not previously been accounted in the official inventory of the area. Evaporative emissions from light-duty vehicles in the Metropolitan Area of Mexico City were estimated to be 39 % of the total annual amount of hydrocarbons emitted. Vehicles built before 1992 (16 % of the fleet) were found to be responsible for 43 % of the total hydrocarbon emissions from exhausts and 31 % of the evaporative emissions of organic compounds. The relatively high amounts of volatile organic compounds emitted from older vehicles found in this study show that strong emission controls need to be implemented in order to decrease the contribution of evaporative emissions of this fraction of the fleet.     

Ecotoxicity and genotoxicity assessment of exhaust particulates from diesel-powered buses

Diesel exhaust is one of the major sources of fine and ultra-fine particulate matter in urban air. Toxicity of diesel-powered engine emissions has been quite widely assessed; however, much less information is available on their ecotoxicity. In our study, the kinetic version of the Vibrio fischeri bioluminescence inhibition bioassay based on the ISO 21338:2010 standard was used to characterise the ecotoxicity of diesel-powered buses. It is a direct contact test in which solid samples are tested in suspension and test organisms are in direct contact with toxic particles. The age of the selected buses fell into a wide range; the oldest one was produced in 1987. Diesel engines of different emission standards (Euro0–Euro4) were included. Measured EC₅₀ values of Euro0–Euro1 engine emissions fell into the same range, 1.24–0.96 μg ml^?1, respectively. On the contrary, emission of Euro4 vehicle proved to be non-toxic. Genotoxic potential of the samples was also estimated, using the colorimetric SOS-chromotest?. Genotoxicity was detected also for Euro0 and Euro1 buses, showing correlation with the ecotoxic potential. The fact that the particulates from Euro4 vehicles did not show ecotoxic/genotoxic effect implies that replacing old Euro1 and Euro2 buses can be a highly effective solution for reducing environmental hazard of automotive emissions. The whole-aerosol testing method is a cheap alternative that can be used in engine developments and emission control.     

Assessment of Mexico��s program to use ethanol as transportation fuel: impact of 6% ethanol-blended fuel on emissions of light-duty gasoline vehicles

Recently, the Mexican government launched a national program encouraging the blending of renewable fuels in engine fuel. To aid the assessment of the environmental consequences of this move, the effect of gasoline fuel additives, ethanol and methyl tert-butyl ether, on the tailpipe and the evaporative emissions of Mexico sold cars was investigated. Regulated exhaust and evaporative emissions, such as carbon monoxide, non-methane hydrocarbons, and nitrogen oxides, and 15 unregulated emissions were measured under various conditions on a set of 2005?C2008 model light-duty vehicles selected based on sales statistics for the Mexico City metropolitan area provided by car manufacturers. The selected car brands are also frequent in Canada, the USA, and other parts of the world. This paper provides details and results of the experiment that are essential for evaluation of changes in the emission inventory, originating in the low-blend ethanol addition in light vehicle fuel.     

简易瞬态工况法排气检测防舞弊措施探讨

介绍了简易瞬态工况法相对于双怠速法的技术优势,分析了该方法排气检测过程中的常见问题与作弊手段。提出以质量控制为基础,采取检测全过程防舞弊措施;与机动车排放监督管理系统建设相结合,对检测设备软件版本实施统一监控;通过实时数据分析,建立检测工位前端防舞弊控制机制;对检测数据分类统计与分析,促进检测工作公正与规范;借助视频监控手段,实现对检测过程的实时监管;加强日常巡查,促进监管工作体系持续完善等建议。     

新车免检新政实施后对高污染车的管理思路与对策的探讨

2014年9月1日起,国家试行6年以内的非营运轿车等车辆免检制度。大多数城市根据此规定,对于车辆的排放定期检验也同步实施6年免检。随着汽车保有量的快速增长,车辆尾气排放对大气环境的影响不容忽视。因此,地方环保部门应针对机动车污染排放的管理重点,从管理手段、管理体制机制、管理对策等方面进一步加强对高污染车辆的监管。     

Assessment of environmentally friendly fuel emissions from in-use vehicle exhaust: low-blend iso-stoichiometric GEM mixture as example

Gasoline–ethanol–methanol fuel blends were formulated with the same stoichiometric air-to-fuel ratio and volumetric energy concentration as any binary ethanol–gasoline blend. When the stoichiometric blends operated in a vehicle, the time period, injector voltage, and pressure for each fuel injection event in the engine corresponded to a given stoichiometric air-to-fuel ratio, and the load was essentially constant. Three low oxygen content iso-stoichiometric ternary gasoline–ethanol–methanol fuel blends were prepared, and the properties were compared with regular-type fuel without added oxygen. One of the ternary fuels was tested using a fleet of in-use vehicles for15 weeks and compared to neat gasoline without oxygenated compounds as a reference. Only a small number of publications have compared these ternary fuels in the same engine, and little data exist on the performance and emissions of in-use spark-ignition engines. The total hydrocarbon emissions observed was similar in both fuels, in addition to the calculated ozone forming potential of the tailpipe and evaporative emissions. In ozone non-attainment areas, the original purpose for oxygenate gasolines was to decrease carbon monoxide emissions. The results suggest that the strategy is less effective than expected because there still exist a great number of vehicles that have suffered the progressive deterioration of emissions and do not react to oxygenation, while new vehicles are equipped with sophisticated air/fuel control systems, and oxygenation does not improve combustion because the systems adjust the stoichiometric point, making it insensitive to the origin of the added excess oxygen (fuel or excess air).

Open image in new window

Graphical abstract Low level ternary blend of gasoline–ethanol–methanol were prepared with the same stoichiometric air–fuel ratio and volumetric energy concentration, based on the volumetric energy density of the pre-blended components. Exhaust and evaporative emissions was compared with a blend having no oxygen in a fleet of 12 in-use vehicles. Vehicles that had suffer a normal deterioration of emissions and do not react to oxygenation, and new vehicles with more sophisticated air/fuel control systems do not improve combustion

     

不同类型机动车尾气挥发性有机化合物排放特征研究

机动车尾气主要成分包括一氧化碳、氮氧化物、碳氢化合物、铅及苯并[a]芘等.其中,挥发性有机化合物由于其对光化学烟雾的贡献及对人体健康的影响而成为近年来大气化学研究的热点.文章首次对北京市9种车辆、5种燃料在不同工况下排放挥发性有机化合物特征进行了定量研究.结果表明,车型、燃料、净化器及工况等因素对排放量产生影响,电喷车比化油器车排放低,其中,夏利比富康与奥迪排放量高;LPG与汽油车排放量最高,柴油车与CNG车排放最低.其中,-10#柴油车比0#柴油车排放更低;使用净化器可以降低挥发性有机化合物排放量;不同工况对排放量的影响随车型、燃料类型的不同而不同.因此,使用清洁燃料、安装净化器和使用电喷装置,可减少尾气中挥发性有机化合物含量.     

Exposure of motorcycle,car and bus commuters to carbon monoxide on a main road in the Tel Aviv metropolitan area,Israel

Short-term personal exposure of passengers in different types of motor vehicles to carbon monoxide was investigated in an intensively used main road in Israel’s Tel Aviv metropolitan area. According to monitoring stations of the Ministry for Environmental Protection (MEP), concentrations of carbon monoxide (CO) along the road, at a height of 3 m above pedestrian level, in the Tel Aviv metropolitan area, are currently very low. However, these measurements do not reflect the actual exposure of commuters, which were the main objective of this study. Four vehicle types/travel modes were investigated: private cars with closed windows, private cars with open windows, motorcycles, and buses. The commuter CO average exposure was the accumulative exposure divided by the duration of the sampling taken along the route, for each type of vehicles. The results showed that commuters in cars with closed windows were exposed to the highest mean CO level, 27.2 ppm, for a period of 38 min; those in a car with open windows, to 19.7 ppm for 38 min; motorcycle riders, to 12.8 ppm, for 17 min; and bus users were exposed to the lowest mean pollution level, of only 3.6 ppm, for 25 min. Thus, CO values of 1 to 3 ppm, as measured at an MEP adjacent monitoring station, may indicate the exposure to CO pollution of area residents, but do not represent the actual exposure of commuters on the congested main road.     

2020年江苏省机动车排放污染分布特征及与大气质量耦合性研究

依据生态环境部2021年6月发布的《排放源统计调查产排污核算方法和系数手册》,结合本地实测数据,在对汽油车颗粒物(PM)排放系数进行测算的基础上,核算了2020年江苏省机动车PM、氮氧化物(NO_(X))、挥发性有机物(VOC_(S))的排放总量,分析了机动车排放污染分布特征及与大气质量的耦合关系。结果表明:2020年江苏省机动车PM、NO_(X)、VOC_(S)排放量分别为0.5×10^(4),3.71×10^(5),1.17×10^(5) t。从区域分布来看,苏州、南京、无锡3市的3项污染物排放总量及NO_(X)、VOC_(S)排放量均位列前3位,PM排放量位列前3位的是苏州、徐州、无锡。从车型、燃料类型和排放阶段来看,国Ⅳ及以下排放标准的汽油小型客车是机动车VOC_(S)排放控制的重点,国Ⅲ排放标准的重型柴油货车是机动车PM和NO_(X)排放控制的重点。分析区域机动车PM排放量与大气中PM_(2.5)来源解析结果的耦合关系,其间存在不同程度的正相关性,控制机动车污染对改善大气环境会产生积极成效,南京、徐州和盐城3市的成效会尤为明显。     

深圳市机动车年检站环保行为剖析

通过对深圳市机动车年检站的社会定位和排气检测现状的描述,分析了各年检站对排气检测这一环保项目的经营态度以及与政府各相关部门及车属单位等的相互关系,提出了对年检站从事机动车排气检测工作,其环保行为应加强监督管理的思路     

Application of CMB model for source apportionment of polycyclic aromatic hydrocarbons (PAHs) in coastal surface sediments from Rizhao offshore area, China

Polycyclic aromatic hydrocarbons (PAHs) in coastal surface sediments from Rizhao offshore area were analyzed by gas chromatography–mass spectrometry. A chemical mass balance (CMB) model developed by the U.S. Environmental Protection Agency (EPA), CMB8.2, was used to apportion sources of PAHs. Seven possible sources, including coal residential, coal power plant, diesel engines exhaust, gasoline engines exhaust, coke oven, diesel oil leaks, and wood burning, were chosen as the major contributors for PAHs in coastal surface sediments. To establish the fingerprints of the seven sources, source profiles were collected from literatures. After including degradation factors, the modified model results indicate that diesel oil leaks, diesel engines exhaust, and coal burning were the three major sources of PAHs. The source contributions estimated by the EPA’s CMB8.2 model were 9.25%, 15.05%, and 75.70% for diesel oil leaks, diesel engines exhaust, and coal burning, respectively.     

以电子环保标志为载体构建机动车污染控制物联网体系

以南京为例,探讨以电子环保标志为载体,以射频识别技术构建机动车污染控制物联网体系,通过绿色智能交通系统、公交优先通行系统、高污染车限行执法系统、不同排放标准车辆的通行控制系统、机动车环保远程核查系统、交通污染智能监测在线调控系统、机动车污染联防联控系统、职能部门信息共享系统的建立,达到控制机动车污染、改善交通拥堵、提高...