武汉市秋冬季室内外空气颗粒物以及有机碳、元素碳的污染特征

为了解秋冬季室内外空气颗粒物PM10、PM2.5以及其有机碳和元素碳的污染特征,于2009年10月及12月对武汉大学医学部学生宿舍室内、外PM10、PM2.5进行了两周连续采样。结果表明：秋季室内PM10和PM2.5的平均浓度分别为121.8和91.3μg/m3,室外为153.9和104.2μg/m3;冬季室内PM10...     

Radon in indoor concentrations and indoor concentrations of metal dust particles in museums and other public buildings

The aim of this study was to evaluate the public and occupational exposure to radon and metal-bearing particles in museums and public buildings located in the city of Rio de Janeiro, Brazil. For this study, four buildings were selected: two historic buildings, which currently house an art gallery and an art museum; and two modern buildings, a chapel and a club. Integrated radon concentration measurements were performed using passive radon detectors with solid state nuclear track detector-type Lexan used as nuclear track detector. Air samplers with a cyclone were used to collect the airborne particle samples that were analyzed by the particle-induced X-ray emission technique. The average unattached-radon concentrations in indoor air in the buildings were above 40 Bq/m³, with the exception of Building D as measured in 2009. The average radon concentrations in indoor air in the four buildings in 2009 were below the recommended reference level by World Health Organization (100 Bq/m³); however, in 2011, the average concentrations of radon in Buildings A and C were above this level, though lower than 300 Bq/m³. The average concentrations of unattached radon were lower than 148 Bq/m³ (4pCi/L), the USEPA level recommended to take action to reduce the concentrations of radon in indoor air. The unattached-radon average concentrations were also lower than the value recommended by the European Union for new houses. As the unattached-radon concentrations were below the international level recommended to take action to reduce the radon concentration in air, it was concluded that during the period of sampling, there was low risk to human health due to the inhalation of unattached radon in these four buildings.     

Pollution characteristics of particulate matters emitted from outdoor barbecue cooking in urban Jinan in eastern China

To understand the pollution characteristics of particulate matter emitted from outdoor barbecue cooking in eastern China, measurements of the PM_2.5 mass concentration, the number concentration of particles with a diameter of 0.01 to 1.0 μm, and the particle size distribution from 0.3 to 25 μm were carried out at seven barbecue restaurants in urban Jinan. The average PM_2.5 mass concentration and sub-micron particle number concentrations at a distance of 1 m from the grills were 250 to 1083 μg/m³ and 0.90 × 10⁵ to 2.23 × 10⁵ cm^–3, respectively, which were much higher than those in the ambient air of the urban area. Compared to the ambient atmosphere, barbecue cooking emitted very high levels of particles with a larger increase in the concentrations of super-micron particles than that of sub-micron particles. The super-micron particle number concentrations at the barbecue restaurants were 10 to 100 times higher than those observed in the ambient urban atmosphere. The barbecue smoke had a significant effect on the particle concentrations in the surrounding region. Both mass and number concentrations of particles exhibited maximum values immediately near the barbecue grills and often reached a peak at a distance of 10 to 15 m. The removal efficiency of a range hood for the cooking particles was tested in an indoor kitchen. The range hood effectively cleaned the particulate matter pollution caused by cooking with a removal efficiency larger than 80%. Therefore, the use of a range hood is recommended for outdoor barbecue restaurants coupled with a smoke purifier to clean the emitted high concentrations of particles.

Open image in new window

     

Particle size distributions, PM2.5 concentrations and water-soluble inorganic ions in different public indoor environments: a case study in Jinan, China

In this study, we collected particles with aerodynamic diameter ?2.5 μm (PM_2.5) from three different public indoor places (a supermarket, a commercial office, and a university dining hall) in Jinan, a medium-sized city located in northern China. Water-soluble inorganic ions of PM_2.5 and particle size distributions were also measured. Both indoor and outdoor PM_2.5 levels (102.3–143.8 μg·m^?3 and 160.2–301.3 μg·m^?3, respectively) were substantially higher than the value recommended by the World Health Organization (25 μg·m^?3), and outdoor sources were found to be the major contributors to indoor pollutants. Diurnal particle number size distributions were different, while the maximum volume concentrations all appeared to be approximately 300 nm in the three indoor locations. Concentrations of indoor and outdoor PM_2.5 were shown to exhibit the same variation trends for the supermarket and dining hall. For the office, PM_2.5 concentrations during nighttime were observed to decrease sharply. Among others, SO ₄ ^2? , NH ₄ ⁺ and NO ₃ ^? were found to be the dominant water-soluble ions of both indoor and outdoor particles. Concentrations of NO ₃ ^? in the supermarket and office during the daytime were observed to decrease sharply, which might be attributed to the fact that the indoor temperature was much higher than the outdoor temperature. In addition, domestic activities such as cleaning, water usage, cooking, and smoking also played roles in degraded indoor air quality. However, the results obtained here might be negatively impacted by the small number of samples and short sampling durations.     

Seasonal concentrations of lead in outdoor and indoor dust and blood of children in Riyadh,Saudi Arabia

Because detrimental effects of exposure to lead (Pb) on human health have been observed, we previously investigated concentrations of Pb in water supplies and blood of adult residents of Riyadh, Saudi Arabia. The objectives of the present study were to: (1) examine seasonal rates of deposition of Pb in dust in several areas of Riyadh city, (2) measure concentrations of Pb in both outdoor and indoor dust, (3) compare concentrations of Pb in dust in Riyadh with those reported for other cities, and (4) quantify Pb in blood of children living in Riyadh. Mean, monthly deposition of PB in outdoor dust was 4.7 × 10¹ ± 3.6 tons km^?2, with a mean Pb concentration of 2.4 × 10² ± 4.4 × 10¹ μg/g. Mean, monthly deposition of Pb in indoor dust was 2.7 ± 0.70 tons km^?2, with a mean concentration of 2.9 × 10¹ ± 1.5 × 10¹ μg Pb/g. There was a significant (P < 0.01) correlation between concentrations of Pb in outdoor and indoor dust. There was no correlation between concentrations of Pb in indoor dust and that in blood of children of Riyadh, whereas there was a weakly significant (P < 0.05) correlation between concentrations of Pb in outdoor dust and that in blood of children. The mean (±SD) concentration of Pb in blood of children in Riyadh was 5.2 ± 1.7, with a range of 1.7–1.6 × 10¹ μg/dl. Concentrations of Pb in blood of 17.8 % of children in Riyadh were greater than 10 μg/dl, which is the CDC’s level of concern.     

Suspension and resuspension of dry soil indoors following track-in on footwear

Contamination of the indoor environment by tracked-in outdoor soil has the potential to pose a significant human health threat through exposure to hazardous soil constituents. The indoor distribution of (contaminated) soil following ingress is important when evaluating exposure risk. Here, the time evolution of size-resolved airborne particulate matter aerosolized as a result of mechanical (i.e., footfall or step-on) impacts on a floor surface with a layer of dry soil was investigated using laser particle counters. Suspended particle levels were recorded after step-on impacts that aerosolized soil particles at a single contact point by the action of a human tester who followed a pre-determined walking pattern. The experimental design presumed that the floor area immediately upon entrance indoors is the location of maximum deposition of outdoor soil transferred on footwear. The suspension of soil resulting from the first step-on floor contact and the subsequent resuspension of soil resulting from additional step-on events were quantified by various arrangements of four laser particle counters. Step-on impacts produced a transient increase in particle levels at various lateral distances and heights from the contact point. Also, with increasing distance and height from the step-on contact point, the level of suspended particles after successive step-on events decreased markedly. The results suggested that a lateral component of the dispersion process was more significant than a vertical one under these experimental conditions. A wall jet effect created by the impact of the footfalls on the floor surface was considered responsible for the apparent greater lateral dispersion of the soil particles.     

Evidence of new particle formation during post monsoon season over a high-altitude site of the Western Ghats,India

The formation of ultrafine particles, their growth, and associated characteristic features has been studied during new particle formation events over a high-altitude station of the Western Ghats during the 2014 post-monsoon season. Most of the events were observed during noon time where particle bursts in the nucleation-mode size range from 5 to 25 nm followed by sustained growth in size. This phenomenon persists for ～4–8 h with a growth rate of 1–2 nm h^–1. Peak concentrations of nucleation-mode particles during the event generally vary from 2300 to 5000 cm^–3. The mean growth rate is 1.4 ± 0.42 nm h^–1, particle formation rate is 1.14 ± 0.22 cm^–3 s^–1, coagulation sink is 0.35 ± 0.22 cm^–3 s^–1, and condensational sink is 15.4 ± 2.6?×?10^–3 s^–1. All these values are comparable with earlier results from Indian region. Comparison of size-segregated particle number concentration during days of new particle formation events and those without new particle formation were carried out showing a distinct variation in nucleation and Aitken mode with least variability associated with the accumulation mode.     

Trace element concentration in fine particulate matter (PM<Subscript>2.5</Subscript>) and their bioavailability in different microenvironments in Agra,India: a case study

Exposure to airborne particulate matter results in the deposition of millions of particle in the lung; consequently, there is need for monitoring them particularly in indoor environments. Case study was conducted in three different microenvironments, i.e., urban, rural and roadside to examine the elemental bioavailability in fine particulate matter and its potential health risk. The samples were collected on polytetrafluoroethylene filter paper with the help of fine particulate sampler during August–September, 2012. The average mass concentration of PM_2.5 was 71.23 µg m^?3 (rural), 45.33 µg m^?3 (urban) and 36.71 µg m^?3 (roadside). Elements in PM_2.5 were analyzed by inductively coupled plasma atomic emission spectroscopy. Percentage bioavailability was determined to know the amount of soluble fraction that is actually taken across the cell membrane through inhalation pathway. Cadmium and lead were found to have cancer risk in a risk evaluation using an Integrated Risk Information system.     

北京市区域城市化程度与颗粒物污染的相关性分析

城市化程度的提升带来严重的资源环境问题,尤其是空气污染问题,严重影响了人类的健康。大气中的PM2.5等颗粒物已经成为影响我国城市空气质量的主要污染物。现有研究多数是对于多年来多地区的宏观研究,缺乏对于典型地区的具体数据报道。通过分析北京市PM2.5和PM10的质量浓度与不同城市化程度地区的相关关系,探索城市化程度对PM2.5等颗粒物浓度的影响。选取北京市7处具有代表性空气质量监测点,于2013年7月至10月对PM2.5和PM10的质量浓度进行连续4个月的实时监测,结合《北京市区域统计年鉴》中的城市化指标数据,包括常住人口密度、地区生产总值和林木覆盖率,对数据进行变化趋势分析、Pearson相关分析和回归分析。研究结论表明：由于北京市不同区域城市化程度不同导致颗粒物污染状况不同,每个区域的PM2.5与PM10的质量浓度虽有差异但均显著相关,PM2.5的质量浓度约占PM10的质量浓度的60%,PM2.5是PM10的主要组成成分。城市化程度与PM2.5等颗粒物浓度有明显的关系,PM2.5等颗粒物浓度与地区生产总值和林木覆盖率显著相关,与地区生产总值呈正相关,与林木覆盖率呈负相关;与常住人口密度呈正相关趋势但并不显著相关。其中,PM2.5的质量浓度与地区生产总值的相关系数为0.875,与林木覆盖率的相关系数为-0.838;PM10的质量浓度与地区生产总值相关系数为0.947,与林木覆盖率相关系数为-0.775。总体来看,PM2.5等颗粒物浓度随城市化程度的提高而增加,北京市区域城市化程度与颗粒物污染情况关系明显。我国在快速发展城市化的同时,应关注环境与经济相协调。调整产业结构,增加植被绿化,控制污染源将有助于减少北京市大气中颗粒物的污染程度,为我国的城市化进程提供相应的支持和保障。     

广州夏季办公室内细颗粒中多环芳烃污染特征研究

大部分的都市办公人群每天在办公室至少度过8 h。而室外环境的渗透、办公室内吸烟、办公设备使用和中央通风系统均可能导致细颗粒物及多环芳烃(PAHs)在室内积聚而造成微环境污染。2015年5—6月,在广州市3种不同功能区(商住区、高新产业区、工业区)共选取了14间不同类型的办公室,对其室内外PM_(2.5)和多环芳烃进行同步监测。结果表明,(1)14间中有12间办公室内的PM_(2.5)浓度水平高于世界卫生组织(WHO)的推荐值25μg·m-3;(2)与国内外类似研究相比,办公室内外∑16PAHs及Ba P-eq的监测浓度水平均较低,并呈现一致规律:文印>室外>吸烟>多人>单人>无窗(无人),其中Ba P-eq低于欧盟规定的安全限值1 ng·m-3;(3)文印工作和吸烟行为与室内PM_(2.5)和PAHs浓度升高有密切关系,分别对5环和4环PAHs贡献明显;(4)其他无明显内源的办公室的细颗粒中PAHs污染在监测期间主要来源于室外贡献。     

Geologic materials and gamma radiation in the built environment

Human exposure to natural ionizing radiation is due to both internal sources such as ingestion and inhalation of radioactive isotopes, and external sources from cosmic radiation and primordial radionuclides present in the Earth crust. Primordial radionuclides are ⁴⁰K and radioisotopes of the decay series of ²³⁸U and ²³²Th, which emit gamma radiation at low doses. Gamma emission can occur both in outdoor, due to background geologic radiation, and in indoor spaces, due to the use of geologic materials in dwellings. This radiation has received less attention than man-made sources because it contributes less to the total doses that affect humans, on the average. However, there are geographical areas and rocks used as building materials that contain high concentrations of radionuclides, thus being a source of relatively high gamma dose exposures. Assessing exposure is difficult, especially in indoor situations where there are marked variations regarding materials application. Nonetheless, some measures and regulations to control such dose exposures on building materials have been suggested. This article reviews gamma radiation in geologic materials used for buildings. We discuss: (1) procedures that relate radionuclide contents in building materials to external gamma radiation, considering namely indoor applications and that are used for establishing restrictions on building materials commerce; (2) relation of rock radionuclide contents with their geologic history that can lead to listing of some geologic materials as potentially hazardous in terms of gamma radiation; and (3) the implications for the European regulation, which has an universal criteria that might be excessively restrictive for the commerce of geologic materials used in small amounts, and does not have provisions regarding existing structures where geologic materials are used in extended amounts.     

The evolution of pollution profile and health risk assessment for three groups SVOCs pollutants along with Beijiang River,China

Three important groups of semi-volatile organic compounds (SVOCs), polycyclic aromatic hydrocarbons (PAHs), organic chlorinated pesticides (OCPs) and phthalate esters (PAEs), were produced by various human activities and entered the water body. In this study, the pollution profiles of three species including 16 PAHs, 20 OCPs and 15 PAEs in water along the Beijiang River, China were investigated. The concentrations of Σ₁₆PAHs in the dissolved and particulate phases were obtained as 69–1.5 × 10² ng L^?1 and 2.3 × 10³–8.6 × 10⁴ ng g^?1, respectively. The levels of Σ₂₀OCPs were 23–66 ng L^?1 (dissolved phase) and 19–1.7 × 10³ ng g^?1 (particulate phase). Nevertheless, higher levels of PAEs were found both in the dissolved and particulate phases due to abuse use of plastic products. Furthermore, non-cancer and cancer risks caused by these SVOCs through the ingestion absorption and dermal absorption were also assessed. There was no non-cancer risk existed through two kinds of exposure of them at current levels, whereas certain cancer risk existed through dermal absorption of PAHs in the particulate phase in some sampling sites. The results will show scientific insights into the evaluation of the status of combined pollution in river basins, and the determination of strategies for incident control and pollutant remediation.     

Exposure assessment of particulate matter and blood chromium levels in people living near a cement plant

This study evaluates the effect of air pollution caused by cement plants on nearby residential areas and performs an exposure assessment of particulate matter (PM) and total Cr, Cr⁶⁺, Pb, and Al. Further, the blood Cr levels of residents exposed to PM released by cement plants are also assessed. Nine buildings (eight residential and one elementary school building) close to cement plants were selected for this study, which were located in Pyeongtaek port, in west of Gyeonggi Province, South Korea. A total of 51 suspended particulate samples were collected at a flow rate of 2.0 L/min. Total Cr was more widely detected in residents’ houses and elementary schools. PM levels were higher at distances of 4.1 and 4.8 km than those at closer distances of 2.7 km. This was due to the influence of wind direction. The estimated mean blood level of Cr for the study participants was 3.80 μg/L, which is higher than levels estimated by other studies on Cr blood levels. Therefore, cement plants could cause an increase in total Cr and blood Cr levels in residential areas, and more continuous monitoring is necessary to better understand their impacts.     

World air particulate matter: sources,distribution and health effects

Particulate matter (PM) is both a major driver of climate change and a source of toxicity for health. In the upper atmosphere, particulate matter modifies the earth radiation budget, cloud formation and acts as a reaction center for air pollutants. In the lower atmosphere, particulate matter changes atmospheric visibility and alters biogeochemical cycles and meteorology. Most critical effects are observed in ambient air, where particulate matter degrades human health. Here we review the sources, spatial and temporal variability, and toxicity of PM₁₀, the particulate matter having particle sizes 10 micrometers or less in diameter, in world regions. For that we analyzed information from the world wide web and databases from government organizations after the year 2000. Findings show that PM₁₀ is a major risk in both developed and developing countries. This risk is more severe in Asian countries compared to Europe and USA, where decreasing trends are recorded during the last two decades. Meteorological factors modify particulate matter variations at local and regional levels. PM_2.5/PM₁₀ ratio provides information of particulate matter sources under different environment conditions. Crustal matter, road traffic and combustion of fuels are major sources of particulate matter pollution. Health studies indicate that long-term exposure to particulate matter has multiple health effects in people from all age groups. Identification of possible sources and their control with regular epidemiological monitoring could decrease the impact of particulate matter pollution.     

Identify the contribution of vehicle non-exhaust emissions: a single particle aerosol mass spectrometer test case at typical road environment

● A single particle observation was conducted in a high traffic flow road environment. ● Major particle types were vehicle exhausts, coal burning, and biomass burning. ● Contribution of non-exhaust emissions was calculated via PMF. ● Proportion of non-exhaust emissions can reach 10.1 % at road environment. A single particle aerosol mass spectrometer (SPAMS) was used to accurately quantify the contribution of vehicle non-exhaust emissions to particulate matter at typical road environment. The PM_2.5, black carbon, meteorological parameters and traffic flow were recorded during the test period. The daily trend for traffic flow and speed on TEDA Street showed obvious “M” and “W” characteristics. 6.3 million particles were captured via the SPAMS, including 1.3 million particles with positive and negative spectral map information. Heavy Metal, High molecular Organic Carbon, Organic Carbon, Mixed Carbon, Elemental Carbon, Rich Potassium, Levo-rotation Glucose, Rich Na, SiO₃ and other categories were analyzed. The particle number concentration measured by SPAMS showed a good linear correlation with the mass concentrations of PM_2.5 and BC, which indicates that the particulate matter captured by the SPAMS reflects the pollution level of fine particulate matter. EC, ECOC, OC, HM and crustal dust components were found to show high values from 7:00–9:00 AM, showing that these chemical components are directly or indirectly related to vehicle emissions. Based on the PMF model, 7 major factors are resolved. The relative contributions of each factor were determined: vehicle exhaust emission (44.8 %), coal-fired source (14.5 %), biomass combustion (12.2 %), crustal dust (9.4 %), ship emission (9.0 %), tires wear (6.6 %) and brake pads wear (3.5 %). The results show that the contribution of vehicle non-exhaust to particulate matter at roadside environment is approximately 10.1 %. Vehicle non-exhaust emissions are the focus of future research in the vehicle pollutant emission control field.     

Trace metal content in inhalable particulate matter (PM<Subscript>2.5–10</Subscript> and PM<Subscript>2.5</Subscript>) collected from historical mine waste deposits using a laboratory-based approach

Mine wastes and tailings are considered hazardous to human health because of their potential to generate large quantities of highly toxic emissions of particulate matter (PM). Human exposure to As and other trace metals in PM may occur via inhalation of airborne particulates or through ingestion of contaminated dust. This study describes a laboratory-based method for extracting PM_2.5–10 (coarse) and PM_2.5 (fine) particles from As-rich mine waste samples collected from an historical gold mining region in regional, Victoria, Australia. We also report on the trace metal and metalloid content of the coarse and fine fraction, with an emphasis on As as an element of potential concern. Laser diffraction analysis showed that the proportions of coarse and fine particles in the bulk samples ranged between 3.4–26.6 and 0.6–7.6 %, respectively. Arsenic concentrations were greater in the fine fraction (1680–26,100 mg kg^?1) compared with the coarse fraction (1210–22,000 mg kg^?1), and Co, Fe, Mn, Ni, Sb and Zn were found to be present in the fine fraction at levels around twice those occurring in the coarse. These results are of particular concern given that fine particles can accumulate in the human respiratory system. Our study demonstrates that mine wastes may be an important source of metal-enriched PM for mining communities.     

Risk remaining from fine particle contaminants after vacuum cleaning of hard floor surfaces

In the indoor environment, settled surface dust often functions as a reservoir of hazardous particulate contaminants. In many circumstances, a major contributing source to the dust pool is exterior soil. Young children are particularly susceptible to exposure to both outdoor derived soil and indoor derived dust present in the indoor dust pool. This is because early in life the exploratory activities of the infant are dominated by touching and mouthing behavior. Inadvertent exposure to dust through mouth contact and hand-to-mouth activity is an inevitable consequence of infant development. Clean-up of indoor dust is, in many circumstances, critically important in efforts to minimize pediatric exposure. In this study, we examine the efficiency of vacuum cleaner removal of footwear-deposited soil on vinyl floor tiles. The study utilized a 5 × 10 foot (c. 152.5 × 305 cm) test surface composed of 1-foot-square (c. 30.5 × 30.5 cm) vinyl floor tiles. A composite test soil with moderately elevated levels of certain elements (e.g., Pb) was repeatedly introduced onto the floor surface by footwear track-on. The deposited soil was subsequently periodically removed from randomly selected tiles using a domestic vacuum cleaner. The mass and loading of soil elements on the tiles following vacuuming were determined both by wet wipe collection and by subsequent chemical analysis. It was found that vacuum cleaner removal eliminated much of the soil mass from the floor tiles. However, a small percentage of the mass was not removed and a portion of this residual mass could be picked up by moistened hand-lifts. Furthermore, although the post-vacuuming tile soil mass was sizably reduced, for some elements (notably Pb) the concentration in the residual soil was increased. We interpret this increased metal concentration to be a particle size effect with smaller particles (with a proportionately higher metal content) remaining in situ after vacuuming.     

Exposure assessment,chemical characterization and source identification of PM2.5 for school children and industrial downwind residents in Guangzhou,China

To assess the exposure doses of PM_2.5 and to investigate its chemical components for the subpopulation (i.e., school children and industrial downwind residents), simultaneous sampling of indoor and outdoor PM_2.5 was conducted at an elementary school close to traffic arteries and a residence located in the downwind area of a steel plant in metropolitan Guangzhou in 2010. Chemical components, i.e., organic carbon, elemental carbon and 6 water soluble ions were analyzed in PM_2.5. A survey was also conducted to investigate the time-activity patterns of the school children and the industrial downwind residents. Indoor and outdoor PM_2.5 were 63.2 ± 20.1 and (76.7 ± 35.8) μg/m³ at the school, and 118.8 ± 44.7 and 125.7 ± 57.1 μg/m³ in the community, respectively. Indoor PM_2.5 was found to be highly related to outdoor sources, and stationary sources were the significant contributors to PM_2.5 at both sites. The daily average doses of PM_2.5 for the school children at the school (D _children) and the industrial downwind residents in the community (D _residents) were (7.6 ± 1.9) and (36.1 ± 36.8) μg/kg-day, respectively. The daily average doses of particulate organic mass and SO₄ ^2? were the two most abundant chemical components in PM_2.5. PM_2.5 exposure for the school children was contributed by indoor and outdoor environments by 48.8 and 51.2 %, respectively; for the industrial downwind residents, the contributions were 66.0 and 34.0 %, respectively. Age and body weight were significantly and negatively correlated with D _children, while age, body weight and education level were significantly and negatively correlated with D _residents; gender was not a significant factor at both cases.     

Indoor and outdoor radon measurements at lung cancer patients’ homes in the dwellings of Rize Province in Turkey

In this study, indoor and outdoor radon (²²²Rn) surveys were carried out in the summer and winter seasons in homes of one hundred lung cancer patients in the year 2013–2014. The aim was to investigate the relationship between radon and cancer patients. Lung cancer patients completed a questionnaire concerning their living environment, various physical parameters and living habits. Pearson correlation and t tests revealed no meaningful results between radon concentrations, on one hand, and environmental and personal living habits, on the other hand. Consequently, the BEIR VI model was adapted and ²²²Rn exposure was estimated to be responsible for about 12% of the lung cancer incidences in the winter season and around 5% in the summer season in the Rize Province. However, due to the limited number of data and numerous parameters that could lead to lung cancer, the estimations done with the model should be taken very lightly. The annual effective doses due to inhalation of indoor and outdoor ²²²Rn were estimated to be, respectively, 1.43 and 0.94 mSv y^?1. The indoor and outdoor annual effective doses were, respectively, close and below the world annual effective dose (1.3 mSv y^?1). At the district level, the indoor annual effective dose equivalent in the ?yidere district was 4.52 mSv y^?1, which was 3.5 times greater than the world average. The number of patients in the majority of the houses in this district was more than one.     

Air pollution below WHO levels decreases by 40 % the links of terrestrial microbial networks

Air pollution has a deleterious impact on public health and the environment. There is few knowledge on the effect of air pollution on terrestrial microbial communities, despite the major role of microbes in ecosystems. Here, we designed an in situ trial ecosystem to assess the impact of moderate atmospheric pollution, below World Health Organization (WHO) thresholds, on an indigenous microbial communities, including bacteria, fungi, ciliates, algae, cyanobacteria, testate amoebae, rotifers and nematodes, extracted from terrestrial bryophytes. These micro-ecosystems were placed at a rural, an urban and an industrial site in France and were thus exposed to various levels of nitrogen dioxide (NO₂), from 6.6–67.9 μg·m^?3, and particulate matter, from 0.7–7.9 μg·m^?3. Microbial analysis was performed by microscopy. We determined atmospheric temperature, relative humidity and particulate matter with diameter lower than 10 µm (PM₁₀), Cu, Cr, Fe, Ni, Pb, Zn in PM₁₀, and (NO₂). Results show a significant impact of chronic moderate exposure to NO₂ and copper Cu-associated particulate matter on the global microbial network complexity. This is evidenced by a loss of about 40 % of microbial co-occurrence links during incubation. Most lost microbial links are ecologically positive links. Moreover, most changes in community co-occurrence networks are related to testate amoebae, a major top predator of microbes. Overall, our findings demonstrate that air pollution can have strong deleterious effects on microbial interactions, even at levels below WHO thresholds.