活性焦和活性炭负载纳米铁处理TNT红水中的二硝基甲苯磺酸钠

以活性焦和活性炭为载体,采用液相还原法制备了负载纳米铁,比较了两种负载纳米铁对TNT红水中难降解物质二硝基甲苯磺酸钠(包括2,4-DNT-3-SO3Na和2,4-DNT-5-SO3Na)的去除能力。实验结果表明,作为负载材料活性焦的相对有效比表面积与孔体积要优于活性炭,而且有利于更好地发挥出负载纳米铁的优势。单位面积活性焦负载纳米铁去除2,4-DNT-5-SO3Na的能力明显高于活性炭负载纳米铁,单位面积活性焦负载纳米铁去除2,4-DNT-3-SO3Na的能力在较小投加量条件下高于活性炭负载纳米铁,但均随投加量的增加而下降;而对于活性炭负载纳米铁,其单位面积去除能力基本不受投加量的影响,而且对二硝基甲苯磺酸钠的去除率高于活性焦负载纳米铁。耦合混凝沉淀的总去除效果表明,单位面活性焦负载纳米铁对2,4-DNT-5-SO3Na的去除能力高于活性炭负载纳米铁,而对2,4-DNT-3-SO3Na的去除能力则低于活性炭负载纳米铁。     

Optimization of nitrate reduction by EDTA catalyzed zero-valent bimetallic nanoparticles in aqueous medium

The present study aims to investigate the EDTA catalyzed reduction of nitrate (NO ₃ ^? ) by zero-valent bimetallic (Fe?CAg) nanoparticles (ZVBMNPs) in aqueous medium and to enumerate the effect of temperature, solution pH, ZVBMNPs dose and EDTA concentration on NO ₃ ^? reduction. Batch experimental data were generated using a four-factor Box?CBehnken design. Optimization modeling was performed using the response surface method for maximizing the reduction of NO ₃ ^? by ZVBMNPs. Significance of the independent variables and their interactions were tested by the analysis of variance and t test statistics. The model predicted maximum reduction capacity (340.15?mg?g^?1 NO ₃ ^? ) under the optimum conditions of temperature, 60?°C; pH?4; dose, 1.0?g?l^?1; and EDTA concentration, 2.0?mmol?l^?1 was very close to the experimental value (338.62?mg?g^?1) and about 16?% higher than the experimentally determined capacity (291.32?mg?g^?1). Study demonstrated that ZVBMNPs had higher reduction efficiency than Fe⁰ nanoparticles for NO ₃ ^? . EDTA significantly enhanced the NO ₃ ^? reduction by ZVBMNPs. The EDTA catalyzed reduction of NO ₃ ^? by ZVBMNPs can be employed for the effective decontamination of water.     

Modeling and optimization of reductive degradation of chloramphenicol in aqueous solution by zero-valent bimetallic nanoparticles

Purpose

The present study aims to investigate the individual and combined effects of temperature, pH, zero-valent bimetallic nanoparticles (ZVBMNPs) dose, and chloramphenicol (CP) concentration on the reductive degradation of CP using ZVBMNPs in aqueous medium.

Method

Iron?Csilver ZVBMNPs were synthesized. Batch experimental data were generated using a four-factor statistical experimental design. CP reduction by ZVBMNPs was optimized using the response surface modeling (RSM) and artificial neural network-genetic algorithm (ANN-GA) approaches. The RSM and ANN methodologies were also compared for their predictive and generalization abilities using the same training and validation data set. Reductive by-products of CP were identified using liquid chromatography-mass spectrometry technique.

Results

The optimized process variables (RSM and ANN-GA approaches) yielded CP reduction capacity of 57.37 and 57.10?mg?g^?1, respectively, as compared to the experimental value of 54.0?mg?g^?1 with un-optimized variables. The ANN-GA and RSM methodologies yielded comparable results and helped to achieve a higher reduction (>6%) of CP by the ZVBMNPs as compared to the experimental value. The root mean squared error, relative standard error of prediction and correlation coefficient between the measured and model-predicted values of response variable were 1.34, 3.79, and 0.964 for RSM and 0.03, 0.07, and 0.999 for ANN models for the training and 1.39, 3.47, and 0.996 for RSM and 1.25, 3.11, and 0.990 for ANN models for the validation set.

Conclusion

Predictive and generalization abilities of both the RSM and ANN models were comparable. The synthesized ZVBMNPs may be used for an efficient reductive removal of CP from the water.     

Aquatic photochemistry of paracetamol in the presence of dissolved organic chromophoric material and nitrate

Purpose

This study contains some new findings connected to the photolysis of the drug paracetamol (hereinafter APAP) especially in light of estimating natural conditions, and it will offer information to better evaluate environmental problems connected with this widely used analgesic agent. Only a few studies, so far, have focussed on the photodegradation process of APAP in the natural environment, and the question about the role of the colored/chromophoric dissolved organic matter (CDOM) and nitrate (NO ₃ ^? ) as photoinductors is almost open.

Methods

APAP dissolved in freshwater and pure laboratory water in the presence and absence of CDOM and NO ₃ ^? ions was irradiated using weak-energy photon energies simulating natural conditions.

Results

CDOM and NO ₃ ^? as photoinductors produced only the slow phototransformation of APAP under weak energy radiation, and APAP seemed to be practically resistant to direct photolysis under weak radiant energies available in natural conditions. The estimated reaction efficiencies, in addition to half-lives, speak for that NO ₃ ^? and CDOM do not act as quite independent photoinductors but their effect in conjunction (CDOM?CNO ₃ ^? ?Cwater) is stronger than the separate ones. The principal phototransformation intermediates of APAP were mono-hydroxy derivatives, depending on available photon energies formed via ortho- or meta-hydroxylation, possessing substantial power of resistance to further specific transformation reactions.

Conclusions

The estimated half-life of the phototransformation of APAP in the natural aqueous environment and in the presence of suitable photoinductors will be about 30?days or more.     

Removal of faecal indicator pathogens from waters and wastewaters by photoelectrocatalytic oxidation on TiO2/Ti films under simulated solar radiation

Purpose

The disinfection efficiency of water and secondary treated wastewater by means of photoelectrocatalytic oxidation (PEC) using reference strains of Enterococcus faecalis and Escherichia coli as faecal indicators was evaluated. Operating parameters such as applied potential (2?C10?V), initial bacterial concentration (10³?C10⁷?CFU/mL), treatment time (up to 90?min) and aqueous matrix (pure water and treated effluent) were assessed concerning their impact on disinfection.

Methods

PEC experiments were carried out using a TiO₂/Ti film anode and a zirconium cathode in the presence of simulated solar radiation. Bacterial inactivation was monitored by the culture method and real-time SYBR green PCR.

Results

A 6.2 log reduction in E. faecalis population was achieved after 15?min of PEC treatment in water at 10?V of applied potential and an initial concentration of 10⁷?CFU/mL; pure photocatalysis (PC) led to only about 4.3 log reduction, whilst negligible inactivation was recorded when the respective electrochemical oxidation process was applied (i.e. without radiation). PEC efficiency was generally improved increasing the applied potential and decreasing initial bacterial concentration. Regarding real wastewater, E. coli was more susceptible than E. faecalis during treatment at a potential of 5?V. Wastewater disinfection was affected by its complex composition and the contained mixed bacterial populations, yielding lower inactivation rates compared to water treatment. Screening the results obtained from both applied techniques (culture method and real-time PCR), there was a discrepancy regarding the recorded time periods of total bacterial inactivation, with qPCR revealing longer periods for complete bacterial reduction.

Conclusions

PEC is superior to PC in terms of E. faecalis inactivation presumably due to a more efficient separation and utilization of the photogenerated charge carriers, and it is mainly affected by the applied potential, initial bacterial concentration and the aqueous matrix.     

Characterization of PM10 atmospheric aerosol at urban and urban background sites in Fuzhou city, China

Background

PM₁₀ aerosol samples were simultaneously collected at two urban and one urban background sites in Fuzhou city during two sampling campaigns in summer and winter. PM₁₀ mass concentrations and chemical compositions were determined.

Methods

Water-soluble inorganic ions (Cl^?, NO ₃ ^? , SO ₄ ^2? , NH ₄ ⁺ , K⁺, Na⁺, Ca²⁺, and Mg²⁺), carbonaceous species (elemental carbon and organic carbon), and elements (Al, Si, Mg, K, Ca, Ti, V, Cr, Mn, Fe, Ni, Cu, Zn, As, Se, Br, and Pb) were detected using ion chromatography, thermal/optical reflectance, and proton-induced X-ray emission methods, respectively.

Results

PM₁₀ mass concentrations, as well as most of the chemical components, were significantly increased from urban background to urban sites, which were due to enhanced anthropogenic activities in urban areas. Elements, carbonaceous species, and most of the ions were more uniformly distributed at different types of sites in winter, whereas secondary ion SO ₄ ^2? , NO ₃ ^? , and NH ₄ ⁺ showed more evident urban-background contrast in this season. The chemical mass closure indicated that mineral dust, organic matters, and sulfate were the most abundant components in PM₁₀. The sum of individually measured components accounted for 86.9?C97.7% of the total measured PM₁₀ concentration, and the discrepancy was larger in urban area than in urban background area.

Conclusion

According to the principal component analysis?Cmultivariate linear regression model, mineral dust, secondary inorganic ions, sea salt, and motor vehicle were mainly responsible for the PM₁₀ particles in Fuzhou atmosphere, and contributed 19.9%, 53.3%, 21.3%, and 5.5% of PM₁₀, respectively.     

Lead concentration increase in the hepatic and gill soluble fractions of European chub (Squalius cephalus)—an indicator of increased Pb exposure from the river water

Purpose

To examine if chronic exposure of feral fish to elevated Pb concentrations in the river water (up to 1???g?L^?1), which are still lower than European recommendations for dissolved Pb in surface waters (7.2???g?L^?1; EPCEU (Official J L 348:84, 2008)), would result in Pb accumulation in selected fish tissues.

Methods

Lead concentrations were determined by use of HR ICP-MS in the gill and hepatic soluble fractions of European chub (Squalius cephalus) caught in the Sutla River (Croatia?CSlovenia).

Results

At the site with increased dissolved Pb in the river water, soluble gill Pb levels (17.3???g?L^?1) were approximately 20 times higher compared to uncontaminated sites (0.85???g?L^?1), whereas the ratio between contaminated (18.1???g?L^?1) and uncontaminated sites (1.17???g?L^?1) was lower for liver (15.5). Physiological variability of basal Pb concentrations in soluble gill and hepatic fractions associated to fish size, condition, sex, or age was not observed, excluding the possibility that Pb increase in chub tissues at contaminated site could be the consequence of studied biotic parameters. However, in both tissues of Pb-exposed specimens, females accumulated somewhat more Pb than males, making female chubs potentially more susceptible to possible toxic effects.

Conclusions

The fact that Pb increase in gill and hepatic soluble fractions of the European chub was not caused by biotic factors and was spatially restricted to one site with increased dissolved Pb concentration in the river water points to the applicability of this parameter as early indicator of Pb exposure in monitoring of natural waters.     

Characteristics of precipitation chemistry at Lushan Mountain, East China: 1992–2009

Introduction

Trends in precipitation pH and conductivity during 1992?C2009, and in ionic compositions from January 2007 to June 2009, are reported from Lushan Mountain, one of the highest mountains in mid-east China. Annual mean pH was in the range of 4.35?C5.01 and showed a statistically very significant (P?P?Results and discussions Over the period of study, Lushan Mountain received more rainfall in spring and summer. The pH values varied seasonally with winter minima. The winter multiyear seasonal mean pH was 4.35. The corresponding summer value was 4.88. SO ₄ ^2? and NO ₃ ^? were the main anions, and NH ₄ ⁺ and Ca²⁺ the main cations. The anion to cation ratio was 0.8?C1.0, and that of [SO ₄ ^2? ] to [NO ₃ ^? ] was 2.4-3.0, much lower than that of the 1980s. However, sulfuric acid was still the main acid present. The ratio of [NH ₄ ⁺ ] to [Ca²⁺] was about 1.0, suggesting that these two alkaline substances provided close acid neutralizing capacity. The ratio of [Cl^?] to [Na⁺] was about 0.67, somewhat lower than that of natural precipitation.

Conclusions

Ionic composition varied seasonally and was closely correlated to the amounts of rainfall and pollution. Trajectory analyses showed that the trajectories to Lushan Mountain could be classified in six clusters and trajectories originating from the South Sea and the areas surrounding Lushan Mountain had the greatest impacts on precipitation chemistry.     

Microbial structure and chemical components of aerosols caused by rotating brushes in a wastewater treatment plant

Purpose

Bacterial community structure and the chemical components in aerosols caused by rotating brushes in an Orbal oxidation ditch were assessed in a Beijing municipal wastewater treatment plant.

Methods

Air samples were collected at different distances from the aerosol-generating rotating brushes. Molecular culture-independent methods were used to characterize the community structure of the airborne bacteria in each sample regardless of cell culturability. A clone library of 16S rDNA directly amplified from air DNA of each sample was constructed and sequenced to analyze the community composition and diversity. Insoluble particles and water-soluble ions emitted with microorganisms in aerosols were analysis by a scanning electron microscope together with energy dispersive X-ray spectroscopy and ion chromatogram analyzer.

Results

In total, most of the identified bacteria were Proteobacteria. The majority of sequences near the rotating brushes (the main source of the bioaerosols) were Proteobacteria (62.97 %) with ??-(18.52 %) and ??-(44.45?%) subgroups and Bacteroidetes (29.63 %). Complex patterns were observed for each sampling location, suggesting a highly diverse community structure, comparable to that found in water in the Orbal oxidation ditch. Accompany with microorganisms, 46.36???g/m³ of SO ₄ ^2? , 29.35???g/m³ of Cl^?, 21.51???g/m³ of NO ₃ ^? , 19.76???g/m³ of NH ₄ ⁺ , 11.42???g/m³ of PO ₄ ^3? , 6.18???g/m³ of NO ₂ ^? , and elements of Mg, Cl, K, Na, Fe, S, and P were detected from the air near the aerosols source.

Conclusions

Differences in the structure of the bacterial communities and chemical components in the aerosols observed between sampling sites indicated important site-related variability. The composition of microorganisms in water was one of the most important sources of bacterial communities in bioaerosols. Chemical components in bioaerosols may provide a media for airborne microorganism attachment, as well as a suitable microenvironment for their growth and survival in the air. This study will be benefit for the formulation of pollution standards, especially for aerosols, that take into account plant workers?? health.     

Degradation and mineralization of sulcotrione and mesotrione in aqueous medium by the electro-Fenton process: a kinetic study

Introduction

The degradation and mineralization of two triketone (TRK) herbicides, including sulcotrione and mesotrione, by the electro-Fenton process (electro-Fenton using Pt anode (EF-Pt), electro-Fenton with BDD anode (EF-BDD) and anodic oxidation with BDD anode) were investigated in acidic aqueous medium.

Methods

The reactivity of both herbicides toward hydroxyl radicals was found to depend on the electron-withdrawing effect of the aromatic chlorine or nitro substituents. The degradation of sulcotrione and mesotrione obeyed apparent first-order reaction kinetics, and their absolute rate constants with hydroxyl radicals at pH?3.0 were determined by the competitive kinetics method.

Results and discussion

The hydroxylation absolute rate constant (k _abs) values of both TRK herbicides ranged from 8.20?×?10⁸ (sulcotrione) to 1.01?×?10⁹ (mesotrione) L?mol^?1?s^?1, whereas those of the TRK main cyclic or aromatic by-products, namely cyclohexane 1,3-dione , (2-chloro-4-methylsulphonyl) benzoic acid and 4-(methylsulphonyl)-2-nitrobenzoic acid, comprised between 5.90?×?10⁸ and 3.29?×?10⁹?L?mol^?1?s^?1. The efficiency of mineralization of aqueous solutions of both TRK herbicides was evaluated in terms of total organic carbon removal. Mineralization yields of about 97?C98% were reached in optimal conditions for a 6-h electro-Fenton treatment time.

Conclusions

The mineralization process steps involved the oxidative opening of the aromatic or cyclic TRK by-products, leading to the formation of short-chain carboxylic acids, and, then, of carbon dioxide and inorganic ions.     

Copper chitosan nanocomposite: synthesis, characterization, and application in removal of organophosphorous pesticide from agricultural runoff

Purpose

Removal of malathion from agricultural runoff was studied using novel copper-coated chitosan nanocomposite (CuCH)??a biopolymeric waste obtained from marine industry.

Methods

Synthesis and characterization of the adsorbent using different spectral techniques like Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer, Emmett, and Teller surface analyzer have been carried out. Equilibrium studies have been carried out to optimize the dose rate, pH, and the reaction time. Parathion and methyl parathion removal were also evaluated by CuCH in the batch mode. Using gas chromatography?Cmass spectrometry (GC?CMS) and FTIR studies suitable mechanism for adsorption has been suggested.

Results

The particle size of the adsorbent ranged from 700 to 750?nm. The surface area was found to be 20?m²?g^-1 with a pore volume of 0.11?cc?g^-1. The maximum adsorption capacity of malathion by CuCH was found to be 322.6?±?3.5?mg?g^-1 at an optimum pH of 2.0. Presence of copper ions enhanced the adsorption capacity of the adsorbent. The reaction was found to follow pseudo second-order kinetics with a rate constant of 0.53?g?mg^-1?min^-1. Evidence from FTIR indicated that copper ions form a dithionate complex with malathion during the adsorption stage. The adsorbent was found to remove malathion completely from spiked concentration of 2?mg?l^-1 in the agricultural run-off samples. It was also found that CuCH removed other organophospurous pesticides like methyl parathion and parathion under prevailing conditions.

Conclusions

The results indicated that CuCH could be applied for the removal of organophosphorous pesticides.     

Performance evaluation of a tailor-made passive sampler for monitoring of tropospheric ozone

Introduction

This study presents the performance evaluation of a tailor-made passive sampler developed for the monitoring of tropospheric ozone.

Methods

The performance of the passive sampler was tested in the field conditions in terms of accuracy, precision, blank values, detection limit, effects of some parameters such as sampling site characteristics and sampling period on the field blanks, self-consistency, experimental and theoretical uptake rates, shelf life and comparison with commercial passive samplers.

Results

There was an agreement (R ²?=?0.84) between the responses of passive sampler and the continuous automatic analyser. The accuracy of the sampler, expressed as percent relative error, was obtained lower than 15%. Method precision in terms of coefficient of variance for three simultaneously applied passive samplers was 12%. Sampler detection limit was 2.42???g?m^?3 for an exposure period of 1?week, and the sampler can be stored safely for a period of up to 8?weeks before exposure. Satisfactory self-consistency results showed that extended periods gave the same integrated response as a series of short-term samplers run side by side. The uptake rate of ozone was found to be 10.21?mL?min^?1 in a very good agreement with the theoretical uptake rate (10.32?mL?min^?1). The results of the comparison study conducted against a commercially available diffusion tube (Gradko diffusion tube) showed a good linear relationship (R ²?=?0.93) between two passive samplers.

Conclusions

The sampler seems suitable to be used in large-scale measurements of ozone where no data are available or the number of existing automated monitors is not sufficient.     

Enhancement of natural radioactivity in fertilized soil of Faisalabad, Pakistan

Background, goal, and scope

Natural radioactivity in phosphate rock (PR) is transferred to phosphate fertilizer (PF) during the manufacturing process of the PF. The continuous addition of the PF to the cultivated soil accumulates the radionuclides in the land and increases the level of radioactivity in the soil. The purpose of the present study was to investigate the enhanced level of accumulated radioactivity due to the continuous addition of the PF in the farmlands of Nuclear Institute of Agriculture and Biology (NIAB) at Faisalabad in Pakistan. The selected study area consisted of the highly fertilized farmlands and an unfertilized barren land of the NIAB.

Introduction

The understudy area is very fertile for the growth of various types of crops; therefore, four agricultural research institutes have been established at Faisalabad and NIAB is one of those. The NIAB has developed various research farmlands at different places in Pakistan. The crop yield has been increased by adding various fertilizers in the farmlands. The addition of the PF accompanied with the radionuclides enhances radioactivity in the fields. Human being is exposed directly or indirectly to this radiological hazard. A prolong exposure may become a cause of health risk.

Materials and methods

The area of study consisted of three types of lands: the land under cultivation for the last 40 and 30?years called Site 1 and Site 2, respectively, and the barren land was called Site 3. A total of 75 soil samples were collected within the crop rooting zone (up to 25?cm deep) of the soil of the NIAB farms. The samples were dried, pulverized to powder, sealed in plastic containers, and stored to achieve equilibrium between ²²⁶Ra and ²²²Rn. Activity concentrations of the radionuclides ²³⁸U (²²⁶Ra), ²³²Th, and ⁴⁰K in soil samples were determined by using a high resolution gamma ray spectrometry system, consisting of an high purity germanium detector coupled through a spectroscopy amplifier with a PC based MCA installed with Geni-2000 software.

Results

The measured activity concentration levels of ⁴⁰K were 662?±?15, 615?±?17, and 458?±?20?Bq?kg^?1, ²²⁶Ra were 48?±?6, 43?±?5, and 26?±?4?Bq?kg^?1, and that of ²³²Th were 39?±?5, 37?±?5, 35?±?5?Bq?kg^?1, respectively, in the soil of the Sites 1, 2, and 3. Gamma dose rate 1?m above the soil surface was 55, 51, and 40?nGy?h^?1 from Sites 1, 2, and 3, respectively. External dose rates in the rooms constructed of the bricks made of the soil from Sites 1, 2, and 3 were 161, 149, and 114?nGyh^?1, respectively.

Discussions

Activity concentration values of ⁴⁰K and ²²⁶Ra in the soil of Sites 1 and 2 were higher than that in the soil of Site 3. The relative rise of ⁴⁰K was 43?% and 34?% and that of ²²⁶Ra was 85?% and 65?% respectively in these sites. Activity concentrations of ²³²Th in all these sites were in the background range. Gamma dose rate 1?m above soil surface of Sites 1 and 2 was 40?% and 30?% respectively higher than that from the soil of Site 3. The rise in activity of ⁴⁰K and ²²⁶Ra and gamma dose from the Site 1 was greater than that from the Site 2. The least activity and dose were observed from the Site 3. Gamma dose in the dwellings made of fertilized soil bricks of Site 1 and Site 2 were respectively calculated to be 41?% and 32?% higher than that in the abodes made of unfertilized soil bricks of Site 3.

Conclusions

Activity concentrations of ²²⁶Ra and ⁴⁰K were observed to be enhanced in the fertilized farmlands of the NIAB. Outdoor and indoor gamma dose as radiological hazard were found to be increasing with the continuous addition of PF in the understudy farmlands.

Recommendations

It is recommended that naturally occurring radioactive metal should be removed during the process of manufacturing of the PF from the PR.

Prospective

The rise in radioactivity in the farmlands due to the addition of the PF can be a source of direct or indirect exposure to radiation that may enhance cancer risk of the exposed individuals.     

Concentration of organic micropollutants in the atmosphere of Trieste, Italy

Purpose

PCDD/Fs, PCBs, and PAHs, ubiquitous environmental pollutants which are part of the POPs, are mainly produced by anthropogenic activities as well as by natural processes. Occurrences of these pollutants in different sites in Trieste are presented. PCDD/Fs distribution and their possible emission sources are discussed.

Methods

Air samples were collected in different sites near the industrial area, in the city center, and in a background area, using a high-volume sampler equipped with a quartz fiber filter and a PUF. Each sampling lasted a week.

Results

The concentrations of the organochlorinated pollutants are consistent with literature data (??PCDD/Fs and ??dl-PCBs were 5?C38?fg TEQ/Nm³ and 4?C31?fg TEQ/Nm³, respectively), and an apparent seasonal trend was found with slightly higher concentrations in the winter and lower levels in both summer campaigns. Moreover, the isomer profile of each sampling campaign was compared to the fingerprint of a sintering plant, a cement plant, and an incinerator, the main industrial activities in Trieste.

Conclusions

The organic micropollutants were detected in levels consistent with literature data. The results show that the pollutants are uniformally distributed in the atmosphere of Trieste. PCDD/F fingerprints in each site remained almost identical during summer and winter, confirming the yearly prevalence of the emissions from the nearby sintering plant.     

Highly efficient degradation of ofloxacin by UV/Oxone/Co2+ oxidation process

Introduction

In this study, UV/Oxone/Co²⁺ oxidation process was applied to degradation of ofloxacin (OFL) in the presence of Co²⁺ as the catalytic and Oxone as the oxidant. The operation parameters including pH, temperature, dosages of reagents, and reaction time were studied in detail.

Results

The results showed that the optimum conditions for the UV/Oxone/Co²⁺ processes were determined as follows: temperature?=?25°C, pH?=?5.0, [Oxone]?=?0.6?mmol/L, [Oxone]/[Co²⁺]?=?1,000, and reaction time?=?60?min. Under these conditions, 100% of the OFL degraded. The kinetics was also studied, and degradation of OFL by the UV/Oxone/Co²⁺ process could be described by first-order kinetics.

Conclusions

Mineralization of the process was investigated by measuring the total organic carbon (TOC), and the TOC decreased by 87.0% after 60?min. This process could be used as a pretreatment method for wastewater containing ofloxacin.     

Identification of cadmium-excluding welsh onion (Allium fistulosum L.) cultivars and their mechanisms of low cadmium accumulation

Purpose

Screening out cadmium (Cd) excluding cultivars of a crop in agricultural production is an effective way to prohibit Cd entering into food chain.

Methods

A judging criterion for Cd-excluding cultivars based on food safety was suggested and used in the identification of Cd-excluding welsh onion (Allium fistulosum L.) cultivars. A pot culture experiment was carried out to screen out Cd-excluding cultivars, of which the results were confirmed by plot experiments. The relevant factors of Cd accumulation in the pseudostem were analyzed and used in the correlation analysis aiming to study the low Cd accumulation mechanisms.

Results

The concentration of Cd in the pseudostem of welsh onions was 0.08?C0.20, 0.18?C0.41, and 0.26?C0.61?mg/kg fresh weight (FW) under three treatments (1.0, 2.5, and 5.0?mg/kg), respectively. The significant (p? ₃ ^? ?CN, and eight other elements in the tested welsh onion cultivars. Two cultivars were identified as Cd-excluding cultivars, mainly because the accumulation of Cd in their pseudostem was only 0.041?±?0.003 and 0.046?±?0.002?mg/kg FW, and 0.054?±?0.001 and 0.066?±?0.011?mg/kg FW, when growing in plots with Cd concentration of 0.49 and 0.99?mg/kg, respectively.

Conclusions

Ribentiegancongwang and Wuyeqi could be identified as Cd-excluding cultivars. Low bioaccumulation factor of the roots was the main mechanism of Cd-excluding welsh onion cultivars.     

Cloud point extraction for the preconcentration of palladium and lead in environmental samples and determination by flow injection flame atomic absorption spectrometry

Purpose

An online cloud-point extraction (CPE) coupled with flow injection method is developed for the separation and preconcentration of palladium and lead from various matrices using flame atomic absorption spectrometry (FAAS).

Method

The method employs the formation of complexes of the metallic species with dimethylglyoxime, which are subsequently entrapped in the micelles of the surfactant Triton X-114, upon increase of the solution temperature to 60°C and loaded into the flow injection system at a flow rate of 4.6?mL?min^?1. The surfactant rich-phase was retained in a minicolumn packed with animal wool at pH?6 and eluted with 1.0?mol?L^?1 nitric acid in methanol at a flow rate of 1.1?mL?min^?1 directly into the nebulizer of the FAAS. The CPE variables and flow injection conditions affecting the analytical performance of the combined methodology was studied and optimized.

Results

Under the optimized conditions for 25?mL of preconcentrated solution, the enrichment factors were 51 and 44, and the limit of detections were 1.0 and 1.4?ng?mL^?1 for palladium and lead, respectively. Finally, the developed method was applied for the determination of palladium and lead in street dust, soil, radiology waste, catalytic converter, and urban aerosol samples.

Conclusions

Cloud-point extraction coupled with flow injection-FAAS was proposed as an effective preconcentration and separation method for Pd and Pb determination in radiology waste, road dust, soil, and urban aerosol samples. The most favorable feature of this method is its much higher selectivity, sensitivity, rapidity, good extraction efficiency, and employs the green chemistry concept, as it does not require the addition of toxic chemicals. In addition, this proposed method gives very low detection limits and good relative standard.     

Genotoxic effect of ciprofloxacin during photolytic decomposition monitored by the in vitro micronucleus test (MNvit) in HepG2 cells

Purpose

Ciprofloxacin (CIP), a broad-spectrum, second-generation fluoroquinolone, has frequently been found in hospital wastewaters and effluents of sewage treatment plants. CIP is scarcely biodegradable, has toxic effects on microorganisms and is photosensitive. The aim of this study was to assess the genotoxic potential of CIP in human HepG2 liver cells during photolysis.

Methods

Photolysis of CIP was performed in aqueous solution by irradiation with an Hg lamp, and transformation products were monitored by HPLC-MS/MS and by the determination of dissolved organic carbon (DOC). The cytotoxicity and genotoxicity of CIP and of the irradiated samples were determined after 24?h of exposure using the WST-1 assay and the in vitro micronucleus (MN) test in HepG2 cells.

Results

The concentration of CIP decreased during photolysis, whereas the content of DOC remained unchanged. CIP and its transformation products were not cytotoxic towards HepG2 cells. A concentration-dependent increase of MN frequencies was observed for the parent compound CIP (lowest observed effect level, 1.2???mol?L^?1). Furthermore, CIP and the irradiated samples were found to be genotoxic with a significant increase relative to the parent compound after 32?min (P?P?Conclusions Photolytic decomposition of aqueous CIP leads to genotoxic transformation products. This proves that irradiated samples of CIP are able to exert heritable genotoxic effects on human liver cells in vitro. Therefore, photolysis as a technique for wastewater treatment needs to be evaluated in detail in further studies, not only for CIP but in general.     

Use of inorganic wastes as immobilizing agents for soluble P in green waste-based composts

Purpose

The study examines the effectiveness of red mud, blast furnace (BF) slag, and alum-derived water treatment sludge as immobilizing agents for excessive soluble P that had accumulated in three green waste-based composts.

Methods

The three wastes were applied at 0%, 5%, 10%, and 20% w/w to three different composts, all containing extremely high concentrations of extractable P, and were incubated for 60?days. Water-soluble P was measured regularly throughout the incubation period, and at the end, P extractable with resin, 0.05?M NaHCO₃, and 0.005?M H₂SO₄ were also measured.

Results

In the water extracts, inorganic P made up more than 85% of the total P present. All three materials had the ability to adsorb P and thus lowered water-soluble P concentrations. Water treatment sludge was clearly the most effective material, and this was attributed to its amorphous nature (thus, large Brunauer?CEmmett?CTeller surface area) and its acid pH (6.8) compared with the alkaline pH (10?C11) of the other two materials. Water treatment sludge was also the most effective at lowering resin- and NaHCO₃-extractable P. When H₂SO₄ was used as the extractant, BF slag tended to be the most effective material at lowering extractable P, followed by water treatment sludge, and red mud. That is, the P immobilized by water treatment sludge was extractable with acid but not with water, resin, or NaHCO₃.

Conclusions

Water treatment sludge has the potential to be used as an effective immobilizing agent for soluble P in composts, and it should be trialed under field conditions.     

Improvement of biodegradability of PVA-containing wastewater by ionizing radiation pretreatment

Background

Polyvinyl alcohol (PVA) has been widely used as sizing agents in textile and manufacturing industry, and it is a refractory compound with low biodegradability.

Objective

The objective of this paper was to treat the PVA-containing wastewater using gamma irradiation as a pretreatment strategy to improve its biodegradability and to determine the roles of different kinds of radical species played during pretreatment.

Methods

Gamma radiation was carried out in a ⁶⁰Cobalt source station, PVA concentration was analyzed by using a visible spectrophotometer and specific oxygen uptake rate (SOUR, milligram of O₂ per gram of mixed liquor volatile suspended solids (MLVSS) per hour) was measured by a microrespirometer.

Results

The results showed that the biodegradability of PVA-containing wastewater with low initial concentration (e.g., 327.8?mg/l) could be improved greatly with increasing irradiation dose. However, PVA gel formation was observed at higher initial PVA concentration (e.g., 3,341.6?mg/l) and higher irradiation dose, which inhibited PVA degradation by aerobic microorganisms. However, the formed gel could be separated by microfiltration, which led to more than 90% total organic carbon (TOC) removal.

Conclusion

Ionizing radiation could be used as a pretreatment technology for PVA-containing wastewater, and its combination with biological process is feasible.