Total and partial digestion of sediments for the evaluation of trace element environmental pollution

Four different sample treatment methods for the determination of trace elements have been compared: a total digestion with HNO3-H2O2-HF using microwave, and three different standardized methods of fractionation: BCR three-steps sequential extraction, USEPA standard 3050B and ISO standard 11466. The four treatment methods were applied to the determination of Cu and Ni in four samples collected in different areas of Cienfuegos Bay (Cuba). The location of samples and the analytes were selected on the basis of results obtained by previous studies. Analyses following total digestion and BCR three-steps procedure were performed by inductively coupled plasma mass spectroscopy whereas analyses following EPA and ISO procedures were performed by flame atomic absorption spectroscopy. The results obtained have been compared with an estimated anthropic fraction evaluated in each sampling point as the difference between the total concentration and an estimated background concentration level. The BCR three-steps provided the best approximation of the estimated anthropic fraction and was therefore applied also in the determination of Pb and Cd for further consideration.     

Impacts on effluent contaminants from mine sites: risk assessment,fate, and distribution of pollution at basin scale

The environmental implications of mining activities are of worldwide concern. An environmental evaluation at the basin level was conducted because of widespread mining in Cajamarca in Northern Peru. A sediment monitoring program was developed at the Jequetepeque basin, located in Cajamarca. A total of 16 sites were monitored at three different times between June 2009 and July 2010, and a total of 42 samples were collected. All samples were analyzed by microwave digestion and by a sequential extraction scheme following the three-stage European Community Bureau of Reference (three-stage BCR) protocol. Trace element mobilization from the sediments to the water column was assessed by the risk assessment code (RAC). Spatial and temporal distribution of trace elements was evaluated by principal component analysis and hierarchical cluster analysis. Cd, Zn, As, and Pb showed the highest concentrations independent of season. Notably, Cu concentration and mobility increased during the wet season for all samples. Additionally, Hg concentration and mobility increased during the wet season near the mine sites. According to the enrichment factor, the highest enrichments of Cd, Zn, Pb, and As were related to mine runoff. The effect of trace elements near the mine sites at the Jequetepeque basin was considered a significant threat to the environment due to Cd, Zn, Pb, and As, and the concentrations of Cu and Hg were also considered a concern. This work establishes a baseline for the environmental quality status of the Jequetepeque basin that may support water quality management in Peru.     

Sequential extraction combined with isotope analysis as a tool for the investigation of lead mobilisation in soils: application to organic-rich soils in an upland catchment in Scotland

Sequential extraction (modified BCR procedure) combined with isotope analysis has been investigated as a tool for assessing mobilisation of lead into streams at an upland catchment in NE Scotland. The maximum lead concentrations (up to 110 mg kg(-1) in air-dried soil) occurred not at the surface but at about 10 cm depth. The lowest (206)Pb/(207)Pb ratios in any profile occurred, with one exception, at 2.5-5 cm depth. In the one exception, closest to the only road in the area, significantly lower (206)Pb/(207)Pb ratios in the surface soil together with much increased chloride concentrations (in comparison to other surface waters) indicated the possible mobilisation of roadside lead and transfer to the stream. The (206)Pb/(207)Pb ratios in extractable fractions tended at depth towards the ratio measured in the residual phase but the ratios in the oxidizable fraction increased to a value higher than that of the residual phase.     

Stormwater runoff quality from different surfaces in an urban catchment in Beijing, China

Urban stormwater runoff quality, widely investigated around the world, has been monitored less in Beijing, China, which impedes the municipal government to use best management practices to protect surface water. In this study, rainwater and stormwater runoff samples from roofs, roads, and a lawn on the campus of the Research Center for Eco-Environmental Sciences (RCEES) (Beijing, China) and from a ring road, with heavy traffic, have been sampled and analyzed for 31 storm events from June 2004 to August 2005. Total suspended solids (TSS), chemical oxygen demand (COD), 5-day biochemical oxygen demand (BOD5), total nitrogen, and total phosphorus concentrations in rainwater and runoff ranged over 2 or more orders of magnitude, meaning that the highest concentration of a certain pollutant did not always occur in a certain kind of runoff. Runoff contained significantly higher concentrations of pollutants than rainwater. On the campus of RCEES, TSS and total phosphorus in runoff samples from the lawn and roads were significantly higher than those from roofs, while the COD, BOD5, and total nitrogen concentrations were not significantly different in runoff among surfaces. Compared with runoff from the roads on campus, runoff from the ring road contained more COD and total nitrogen, but less TSS, BOD5, and total phosphorus. All pollutants measured in runoff from roofs on campus and from the ring road showed a peak concentration in starting runoff, which then decreased sharply. The peak concentrations of COD, BOD5, total nitrogen, and total phosphorus in the roof runoff increased with the increase in time of the antecedent dry period. Thus, urban stormwater pollution control, especially for first-flush control, is of great importance for the full use of rainwater and prevention of water pollution.     

An ultrasonic assisted extraction method to release heavy metals from untreated sewage sludge samples

A rapid ultrasound accelerated sequential extraction procedure has been used to develop sequential extraction proposed by BCR protocol (the community Bureau of Reference now the European Union "Measurement and Testing Programme"). The effects of the ultrasonic treatment on the extraction of Cu, Cd, Cr, Pb, Ni and Zn from untreated sewage sludge collected from industrial site of Hyderabad city (Pakistan) were compared with those obtained from conventional sequentional extraction procedure of modified BCR protocol. In BCR method, each extraction steps takes 10h, where as with the use of compromise sonication conditions in ultrasonic bath, steps 1-3 of the sequential extraction (excluding the hydrogen peroxide digestion in step 3, which was not performed with sonication) could be completed in 30, 30 and 30 min, respectively. Extractable Cd, Cr, Pb and Ni contents were obtained by both comparable methodologies were measured by electrothermal atomic absorption spectrometry (ETAAS), while for Cu and Zn Flame atomic absorption spectrometry (FAAS) was used. The validations of both methods were compared by the analysis of certified reference material of soil amended with sewage sludge (BCR 483). According to statistical evaluation of the results, the proposed accelerated extraction method is valid alternative to conventional shaking with much shorter extraction time with p value <0.05. The overall metal recoveries in steps 1-3 (excluding residual step) were 95-100% of those obtained with the conventional BCR protocol, except for Cu extracted (91.6%) as related to indicative values of Cu in BCR 483 obtained in 1-3 steps. The results of the partitioning study of untreated industrial waste water sewage sludge, indicate that more easily mobilized forms (acid exchangeable) were predominant for Cd and Zn, in contrast, the largest amount of Pb and Cr was associated with the iron/manganese oxide and organic matter/sulphide fractions.     

Evaluation of non-methane hydrocarbon (NMHC) emissions based on an ambient air measurement in Tokyo area,Japan

Non-methane hydrocarbons (NMHCs) are known to have an important role on air quality due to their high reactivity. NMHC analysis has been performed on 148 ambient air samples collected at five different sites in the Kanto area (Tokyo metropolitan area and surrounding six prefectures) of Japan in summer and winter of 2008, and fifty NMHCs have been determined and quantified. A field measurement campaign has been conducted at one of the busiest intersections in Tokyo metropolitan area in winter of 2008. NMHC emissions are evaluated through comparison of distributions of individual NMHCs emitted from motor vehicles, which are estimated from the measurements, with those determined from the current emissions inventory. The comparison revealed that the measured distributions of acetylene, ethylene and toluene showed a good agreement with those estimated from the emissions inventory (the values estimated from the measurements are a factor of 1.5, 0.56 and 2.3 larger than the emissions inventory in median, respectively), however, propane and isobutane are found to be significantly underestimated in the emissions inventory (the measured values were a factor of 18 and 5.1 larger than the emissions inventory, respectively). The significant underestimate of propane can be explained by that the current emissions inventory does not consider emissions from liquefied propane gas (LPG) fueled vehicles. However, for isobutane, reasons for the underestimate are still unclear. Another field measurement has been conducted in summer of 2008, where the air samples have been collected at three different sites on the ground and by a helicopter as well. Remarkable high concentrations of 1-butene and cis- and trans-2-butenes have been sporadically observed in the samples collected at Urayasu in the coastal area of Tokyo bay. Calculated propylene equivalent (PE) concentrations of butenes revealed that those have a significantly important role in ozone formation when the air plume is affected by emissions from their emission sources. The PE concentrations of butenes varied from 0.1 to 39 ppbC, and accounted for 1.5–75% of total PE concentrations at Urayasu. Most of the continuous air quality monitoring stations does not record concentrations of individual hydrocarbons, therefore, the importance of reactive and low concentration hydrocarbon such as butenes might be overlooked in the current emissions inventory and/or air quality model. In this paper, the reliability of NMHC emissions is evaluated based on the field measurements. Their possible impacts on air quality in the Kanto area are discussed as well, based on the calculated propylene equivalent concentrations.     

Relation between heavy metal concentrations in salt marsh plants and soil

The aim of the research reported here was to investigate the relation between heavy metal concentrations in salt marsh plants, extractability of the metals from soil and some soil characteristics. In April 1987, Spartina anglica and Aster tripolium plants and soil were collected from four salt marshes along the Dutch coast. The redox potential of the soil between the roots of the plants and at bare sites was measured. Soil samples were oven-dried and analyzed for chloride concentration, pH, fraction of soil particles smaller than 63 microm (f < 63 microm), loss on ignition (LOI) and ammonium acetate and hydrochloric acid extractable Cd, Cu and Zn concentrations. The roots and shoots of the plants were analyzed for Cd, Cu and Zn. Because drying of the soil prior to chemical analysis might have changed the chemical speciation of the metals, and therefore the outcome of the ammonium acetate extraction, a second survey was performed in October 1990. In this survey A. tripolium plants and soil were collected from two salt marshes. Fresh and matched oven-dried soil samples were analyzed for water, ammonium acetate and diethylene triaminepentaacetic acid (DTPA) extractable Cd, Cu and Zn concentrations. The soil samples were also analyzed for f < 63 microm, LOI and total (HNO(3)/HCl digestion) metal concentrations. Soil metal concentrations were correlated with LOI. Drying prior to analysis of the soil had a significant effect on the extractability of the metals with water, ammonium acetate or DTPA. Plant metal concentrations significantly correlated only with some extractable metal concentrations determined in dried soil samples. However, these correlations were not consistently better than with total metal concentrations in the soil. It was concluded that extractions of metals from soil with water, ammonium acetate or DTPA are not better predictors for metal concentrations in salt marsh plants than total metal concentrations, and that a major part of the variation in metal concentrations in the plants cannot be explained by variation in soil composition.     

Monitoring of the booster biocide dichlofluanid in water and marine sediment of Greek marinas

Dichlofluanid (N-dichlorofluoromethylthio-N'-dimethyl-N-phenylsulphamide) is used as booster biocide in antifouling paints. The occurrence of dichlofluanid and its metabolite DMSA (N'-dimethyl-N-phenyl-sulphamide) was monitored in seawater and marine sediment from three Greek marinas. Seawater and sediment samples were collected at three representative positions and one suspected hotspot in each marina and shipped to the laboratory for chemical analysis. As part of the project, an analytical method had been developed and validated. Furthermore, some additional experiments were carried out to investigate the potential contribution of paint particle bound dichlofluanid on the total concentration in the sediment. As expected, given its known high hydrolytic degradation rate, no detectable concentrations of dichlofluanid were measured in any of the seawater samples. DMSA was detected in seawater samples at very low concentrations varying from <3 ng l(-1) (LOD) to 36 ng l(-1). During method validation, it had already been demonstrated that dichlofluanid is unstable in sediment and can therefore only be determined as its metabolite DMSA. In a separate experiment, in which marine sediment was spiked with artificial paint particles containing dichlofluanid and then analysed according to the validated method, it was demonstrated that if there is any dichlofluanid originating from paint particles, this would be determined as DMSA. No DMSA was detected in any of the sediment samples. It could therefore be concluded that there were no significant concentrations of dichlofluanid in the sediment samples.     

Concentration changes of PCDDs, PCDFs, and dioxin-like PCBs in human breast milk samples as shown by a follow-up survey

Breast milk is known to discharge dioxins from the human body. However, to date, no direct comparison has been made of the concentrations of dioxin analogues in breast milk obtained from identical population after successive deliveries. We present here follow-up survey results of PCDDs, PCDFs, and dioxin-like PCBs concentrations in human breast milk samples from 35 women living in Tokyo from whom samples had been obtained and analyzed to determine the corresponding concentrations in the past. The average concentrations of total PCDDs, PCDFs, dioxin-like PCBs were 8.5, 5.5, 11 TEQ pg/g fat for the first samples and 5.4, 4.0, 6.6 TEQ pg/g fat for the second samples, respectively. The degrees of reduction of total PCDDs and total dioxin-like PCBs were higher than that of total PCDFs because 1,2,3,7,8-PeCDD, 2,3,4,7,8-PeCDF and 3,3',4,4',5-PeCB (#126), which were the predominant congeners among PCDDs, PCDFs, and dioxin-like PCBs, respectively, had different degrees of reduction. Moreover we observed a significant increase of the concentrations of PCDDs, PCDFs, and dioxin-like PCBs in samples from three women in this follow-up survey, and the patterns of increased isomers differed among the three samples. It was conjectured that the increase of the concentrations was due mainly to dietary intake between deliveries. It is important for pregnant women to have a balanced diet to mitigate the exposure of infants to these chemicals.     

Cyanide generation during preservation of chlorinated wastewater effluent samples for total cyanide analysis.

Dechlorinating agents and pH adjustment are often used to preserve wastewater samples for cyanide analysis. The effects of four approved preservation protocols on the results of the total cyanide analysis of effluents from four water reclamation plants were examined. The results differed widely, and a clear pattern emerged. Immediate analysis without pH adjustment generally gave total cyanide concentrations below the reporting limit of 5 microg/L, irrespective of the dechlorinating agents used. When the pH was adjusted to > or =12, a slight increase in the measured total cyanide concentration was observed when thiosulfate was used to dechlorinate the samples, and a significant increase (>10 microg/L) was observed when arsenite was used as the dechlorinating agent. These results provide evidence that approved preservation protocols may give rise to cyanide formation in chlorinated wastewater effluent matrices.     

Mercury concentration in black flies Simulium spp. (Diptera, Simuliidae) from soft-water streams in Ontario, Canada

Total Hg in Simulium spp. (Diptera, Simuliidae) was measured in 17 soft-water streams in the District of Muskoka and Haliburton County (Ontario, Canada) during 2003 and 2004. Black flies contained 0.07-0.64 microg/g total Hg (dry weight). The methylmercury concentration was measured in 6 samples of the 17, and ranged from 58% to 93% of total Hg. The concentration of total Hg is much higher than has been found in other filter feeding insects, and represents a significant potential source of Hg to fish. Mercury concentrations in Simulium spp. at different sites were strongly positively correlated with dissolved organic carbon, and the proportion of land within each catchment that was wetland. There was also a strong negative correlation with pH. By examining Hg concentration in filter feeding insects we have found a significant entry point for Hg and MeHg into the food web.     

A study of metal and metalloid contaminant availability in Antarctic marine sediments

Previous studies of impacted sites near Casey Station, Antarctica, have revealed elevated concentrations of metals and metalloids, particularly Cd, Cu, Fe, Pb, Sn and Zn in marine sediments. However, attempts to understand the availability and mobility of contaminant elements have not provided a true understanding of speciation. The current work shows, for the first time, that sediments in Brown Bay, an embayment adjacent to the Thala Valley waste disposal site, have elevated concentrations of sulfide, well in excess of that required to bind contaminant metals such as Cd, Cu, Pb and Zn. Furthermore, sediment characterisation using the BCR sequential extraction scheme has shown metal partitioning consistent with sulfides being the controlling factor in metal availability, thus explaining the low porewater concentrations of these metals. The speciation of Sn in Brown Bay, however, is still unclear with the BCR sequential extraction scheme partitioning Sn predominantly into the residual fraction despite Sn being readily extracted by dilute HCl.     

Characterization of gas/particle concentrations and partitioning of polychlorinated biphenyls (PCBs) measured in an urban site of Turkey

Air concentrations of polychlorinated biphenyls (PCBs) in both gas and particle phases were measured in an urban site (BUTAL-Merinos) of the city of Bursa, Turkey between August 2004 and May 2005. The mean of total (particle+gas) PCB concentrations was about 491.8+/-189.4pg/m(3). The main contributors for PCBs in the sampling site were the local sources and long-range atmospheric transport supported by back trajectory analysis. Lower molecular weight PCB congeners generally dominated in the samples. The particle phase of the measured PCBs accounted for 15% of the total PCB concentrations. Gas/particle distribution was investigated using different approaches such as log K(P)-log P(L)(o), log K(P)-log K(OA) and the Junge-Pankow model. Regression analysis among log K(P), log P(L)(o) and log K(OA) exhibited significant correlation at p<0.05. Correlation between PCB homologs and meteorological parameters was formed to investigate the possible relationships.     

Comparison of GC and LC determinations of hexabromocyclododecane in biological samples - results from two interlaboratory comparison studies

In order to assess the quality and comparability of results from determinations of 1,2,5,6,9,10-hexabromocyclododecane (HBCD) in biological samples, two interlaboratory comparison studies have been organized. Up to 13 laboratories determined either the total HBCD concentration, or concentrations of alpha-, beta- and gamma-HBCD, or both in cod liver oil, herring filet, salmon filet, butter and chicken meat. The laboratories were able to determine total HBCD concentrations in the marine samples with satisfying quality (RSD <35%). However, the analysis of samples with low HBCD contamination (相似文献   

Aerosol organic nitrogen over the remote Atlantic Ocean

Water soluble organic nitrogen (WSON) has been measured in aerosols collected on three research cruises on the Atlantic Ocean from approximately 55°N to 45°S. Results are interpreted using air mass back trajectories and results for other aerosol components. WSON concentrations range from <1 to ～40 (median 5.6) nmol m^?3 with significant WSON concentrations in both fine (<1 μm) and coarse mode (>1 μm) aerosol. Concentrations of WSON were highest in samples containing Saharan dust, suggesting a locally significant source associated with soil dust. More generally WSON concentrations were highest in air which had recently crossed continental areas. In the whole data set, WSON is well correlated to total soluble nitrogen and represents approximately 25% of total nitrogen. This correlation implies a significant anthropogenic contribution to the organic nitrogen.     

Mold infestation of wet spray-applied cellulose insulation

Mold investigations were conducted in four buildings that had been insulated with wet spray-applied cellulose insulation (WSACI). Bulk WSACI samples were collected and analyzed by quantitative polymerase chain reaction (QPCR) methods. Airborne mold was evaluated using both Burkard total mold spore and Andersen culturable/viable sampling methods. Although reportedly treated with biocidal borates, QPCR analyses indicated that elevated concentrations of mold cells (reported as spore equivalents per gram) may be present in WSACI. QPCR analyses showed the following: (1) very high concentrations of Penicillium chrysogenum in samples from two of four buildings; (2) very high concentrations of Stachybotrys chartarum in samples from one building and a more moderate presence in a second; (3) moderately high concentrations of Aspergillus versicolor in samples from one building and more moderate concentrations in a second; (4) the presence of the opportunistic pathogen, Aspergillus fumigatus, in samples from three of the four buildings, and (5) the presence of 22 of 23 target mold species. Elevated airborne total mold spore concentrations were observed in all four of the buildings investigated. Culturable/viable airborne mold concentrations were moderately elevated in three of the four buildings. Mold genera/types present were relatively consistent among airborne mold samples collected by both methods and bulk sample analyses. Results of this study suggest that WSACI has the potential to cause elevated airborne mold levels in buildings where it has been applied and pose significant mold exposure and public health risks.     

Source extraction information from air quality data monitored in an Argentinean steel mill

A statistical analysis of a series of ambient air concentrations of suspended particulate matter (SPM) and NO2 is presented. Measurements were taken at four sites that belong to an Argentinean steel mill and in another site located in its vicinity. The air pollutants were measured during a three-week exploratory sampling. The monitoring sites were selected on the basis of relevant characteristics of the emission sources and the corresponding climatological statistics of the last decade. Suspended particulate matter with aerodynamic diameter of less than 10 microm (PM10) and NO2 were continuously measured at only one site, while 1-hr samples of NO2 and 24-hr samples of total SPM and SO2 were collected at the other sites. The registered concentrations show that SPM was the pollutant of major concern. A first estimate about the nature of the contribution of the different sources of particles and NO2 present in the area was obtained through the statistical analysis of measured concentration data coupled with prevalent meteorological variables.     

Air and soil dioxin levels at three sites in Italy in proximity to MSW incineration plants

Levels of polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF) in both air and soil samples were measured at three different sites in Italy, in proximity to three municipal solid waste incinerators (MSWIs) to determine baseline contamination and the contributory role of incinerator emissions. At the first site, located in an agricultural, cattle-breeding, typically flattish area of the Po Valley, the dioxin concentrations had already been measured before the start-up of the new MSWI. These dioxin concentrations were then again measured after two years of continual operation of the incinerator. Despite the presence of the plant, the PCDD/Fs concentrations appear not to have been affected and were found to be in a range of 22-125 fg I-TEQ m(-3) in the air samples and 0.7-1.5 pg I-TEQ g(-1) in the soil samples. The second site is located in an industrial district of the Veneto Region, in the surroundings of an old MSWI that is not equipped with Best Available Technology (BAT) dioxin removal system. The PCDD/Fs concentrations in the air samples were between 144 and 337 fg I-TEQ m(-3). This is a typical range of values for industrial areas, while the soil samples showed contamination levels between 1.1 and 1.4 pg I-TEQ g(-1). The third site lies in the Adige Valley, near a MSWI that has been equipped with BAT for flue gas cleaning. The observed values ranged from 10 to 67 fg I-TEQ m(-3) for the air samples and 0.08-1.2 pg I-TEQ g(-1) for the soil samples. The contributory factors of the varying characteristics of the different areas together with the types of technology adopted at each MSWI plant are discussed. The PCDD/Fs levels are subsequently compared with established values from previous studies.     

Assessment of sediment contamination in Casco Bay, Maine, USA

The current status of contaminant concentrations in Casco Bay, decadal trends of these contaminants and changes in their geographical distribution are assessed using sediment samples collected approximately 10 years apart. In general, regulated contaminants appeared to be decreasing in concentration. Total PAH and dioxins/furans concentrations did not significantly change over this period. Total organochlorine pesticides, 4,4-DDE, 4,4-DDD, total DDT, PCB, tributyltin and total butyltin decreased in concentration. Trace element concentrations in sediments decreased at the majority of the sampling sites for chromium, nickel, and selenium while arsenic, cadmium, copper, lead, mercury, silver, and zinc remained relatively constant. None of the contaminants measured has increased by more than a factor of 2. Selected sites located in the Inner Bay, where concentrations are higher and new inputs were more likely, showed increased concentrations of contaminants. Most contaminants were not found at concentrations expected to adversely affect sediment biota based on ERL/ERM guidelines.     

Sequential extraction of heavy metals in river sediments of an abandoned pyrite mining area: pollution detection and affinity series

In this paper heavy metal pollution at an abandoned Italian pyrite mine has been investigated by comparing total concentrations and speciation of heavy metals (Fe, Cu, Mn, Zn, Pb and As) in a red mud sample and a river sediment. Acid digestions show that all the investigated heavy metals present larger concentrations in the sediment than in the tailing. A modified Tessier's procedure has been used to discriminate heavy metal bound to organic fraction from those originally present in the mineral sulphide matrix and to detect a possible trend of metal mobilisation from red mud to river sediment. Sequential extractions on bulk and size fractionated samples denote that sediment samples present larger percent concentrations of the investigated heavy metals in the first extractive steps (I-IV) especially in lower dimension size fractionated samples suggesting that heavy metals in the sediment are significantly bound by superficial adsorption mechanisms.