The estimation of N2O emissions from municipal solid waste incineration facilities: The Korea case

The greenhouse gases (GHGs) generated in municipal solid waste (MSW) incineration are carbon dioxide (CO₂), methane (CH₄), and nitrous oxide (N₂O). In South Korea case, the total of GHGs from the waste incineration facilities has been increasing at an annual rate 10%. In these view, waste incineration facilities should consider to reduce GHG emissions.This study is designed to estimate the N₂O emission factors from MSW incineration plants, and calculate the N₂O emissions based on these factors. The three MSW incinerators examined in this study were either stoker or both stoker and rotary kiln facilities. The N₂O concentrations from the MSW incinerators were measured using gas chromatography-electron capture detection (GC-ECD) equipment.The average of the N₂O emission factors for the M01 plant, M02 plant, and M03 plant are 71, 75, and 153 g-N₂O/ton-waste, respectively. These results showed a significant difference from the default values of the intergovernmental panel on climate change (IPCC), while approaching those values derived in Japan and Germany. Furthermore, comparing the results of this study to the Korea Energy Economics Institute (KEEI) (2007) data on waste incineration, N₂O emissions from MSW incineration comprised 19% of the total N₂O emissions.     

The environmental comparison of landfilling vs. incineration of MSW accounting for waste diversion

This study evaluates the environmental performance and discounted costs of the incineration and landfilling of municipal solid waste that is ready for the final disposal while accounting for existing waste diversion initiatives, using the life cycle assessment (LCA) methodology. Parameters such as changing waste generation quantities, diversion rates and waste composition were also considered. Two scenarios were assessed in this study on how to treat the waste that remains after diversion. The first scenario is the status quo, where the entire residual waste was landfilled whereas in the second scenario approximately 50% of the residual waste was incinerated while the remainder is landfilled. Electricity was produced in each scenario. Data from the City of Toronto was used to undertake this study. Results showed that the waste diversion initiatives were more effective in reducing the organic portion of the waste, in turn, reducing the net electricity production of the landfill while increasing the net electricity production of the incinerator. Therefore, the scenario that incorporated incineration performed better environmentally and contributed overall to a significant reduction in greenhouse gas emissions because of the displacement of power plant emissions; however, at a noticeably higher cost. Although landfilling proves to be the better financial option, it is for the shorter term. The landfill option would require the need of a replacement landfill much sooner. The financial and environmental effects of this expenditure have yet to be considered.     

Tools for evaluation of impact associated with MSW incineration: LCA and integrated environmental monitoring system

The identification of significant pollutants emitted from the contamination source is the first step in evaluating the impact associated with anthropic activity. Municipal solid waste (MSW) incinerators are still generally perceived as great pollutant sources, in particular due to their gaseous emissions from the stack, which constitute the major effluent from the plant. In this work a life cycle assessment and an integrated environmental monitoring system were applied together, in order to obtain complete information about the incineration process and its environmental impact. The former is a proven methodology, but its application to waste management systems constitutes a relatively new field of application with a great developmental potential. The contribution of the incineration process to the different environmental impact categories was investigated, finding many avoided impacts due to energy recovery. The latter is an innovative approach that allows a remarkable understanding of impact due to a contamination source; interesting correlations were found between heavy metals both in gas emissions and in natural matrices in the surroundings.     

Process control in municipal solid waste incinerators: survey and assessment.

As there is only rare and scattered published information about the process control in industrial incineration facilities for municipal solid waste (MSW), a survey of the literature has been supplemented by a number of waste incineration site visits in Belgium and The Netherlands, in order to make a realistic assessment of the current status of technology in the area. Owing to the commercial character, and therefore, the confidentiality restrictions imposed by plant builders and many of the operators, much of the information collected has either to be presented in a generalized manner, and in any case anonymously. The survey was focused on four major issues: process control strategy, process control systems, monitors used for process control and finally the correlation between the 850 degrees C/2 s rule in the European waste incineration directive and integrated process control. The process control strategies range from reaching good and stable emissions at the stack to stabilizing and maximizing the energy output from the process. The main indicator to be monitored, in cases in which the focus is controlling emissions, is the oxygen content in the stack. Keeping the oxygen concentration in a determined range (usually between 8 and 12 vol.%) ensures stable and tolerated concentrations of the gaseous emissions. In the case for which stabilization of energy production is the principal aim, the main controlled parameter is the steam temperature and flow-rate, which is usually related to the fuel energetic input. A lot of other parameters are used as alarm criteria, the most common of which is the carbon monoxide concentration. The process control systems used most commonly feature partially automated classical proportional integral derivative (PID) controllers. New and innovative process control systems, such as fuzzy-logic control systems, are still unknown to most plant managers while their performance is reported to be unsatisfactory in plants in which such systems have been tested or are in use. Monitoring components used in process control are still based on classical tools such as thermocouples. The use of modern and more reliable sensors is very limited due to the high initial investment cost or simply the fear of using non-standard technologies. Complying with the 850 degrees C/2 s rule in the European waste incineration directive generally is seen to be a handicap for the process control, either in terms of cost, or flexibility of reaction, or both, particularly in old incineration facilities where such restrictions were not planned in the design.     

Optimal utilization of waste-to-energy in an LCA perspective

Energy production from two types of municipal solid waste was evaluated using life cycle assessment (LCA): (1) mixed high calorific waste suitable for production of solid recovered fuels (SRF) and (2) source separated organic waste. For SRF, co-combustion was compared with mass burn incineration. For organic waste, anaerobic digestion (AD) was compared with mass burn incineration. In the case of mass burn incineration, incineration with and without energy recovery was modelled. Biogas produced from anaerobic digestion was evaluated for use both as transportation fuel and for heat and power production. All relevant consequences for energy and resource consumptions, emissions to air, water and soil, upstream processes and downstream processes were included in the LCA. Energy substitutions were considered with respect to two different energy systems: a present-day Danish system based on fossil fuels and a potential future system based on 100% renewable energy. It was found that mass burn incineration of SRF with energy recovery provided savings in all impact categories, but co-combustion was better with respect to Global Warming (GW). If all heat from incineration could be utilized, however, the two alternatives were comparable for SRF. For organic waste, mass burn incineration with energy recovery was preferable over anaerobic digestion in most impact categories. Waste composition and flue gas cleaning at co-combustion plants were critical for the environmental performance of SRF treatment, while the impacts related to utilization of the digestate were significant for the outcome of organic waste treatment. The conclusions were robust in a present-day as well as in a future energy system. This indicated that mass burn incineration with efficient energy recovery is a very environmentally competitive solution overall.     

Size distribution and number concentration of particles at the stack of a municipal waste incinerator

A large number of particles and gaseous products are generated by waste combustion processes. Of particular importance are the ultrafine particles (less than 0.1 microm in aerodynamic diameter) that are emitted in large quantities from all the combustion sources. Recent findings of toxicological and epidemiological studies indicate that fine and ultrafine particles could represent health and environmental risks. Quantifying particulate emissions from combustion sources is important: (i) to examine the source status in compliance with regulations; (ii) to create inventories of such emissions at local, regional and national levels, for developing appropriate management and control strategies in relation to air quality; (iii) to predict ambient air quality in the areas involved at the source and (iv) to perform source apportionment and exposure assessment for the human populations and/or ecological systems involved. In order to control and mitigate the particles in the view of health and environmental risk reduction, a good understanding of the relative and absolute contribution from the emission sources to the airborne concentrations is necessary. For these purposes, the concentration and size distribution of particles in terms of mass and number in a waste gas of a municipal waste incineration plant were measured in the stack gas. The mass concentrations obtained are well below the imposed daily threshold value for both incineration lines and the mass size distribution is on average very stable. The total number concentrations are between 1 x 10(5) and 2 x 10(5)particles/cm(3) and are on average relatively stable from one test to another. The measured values and the comparison with other point sources show a very low total number concentration of particles at the stack gas, revealing the importance of the flue gas treatment also for ultrafine particles. Also in respect to linear sources (high and light duty vehicles), the comparison shows a negligible emission in terms of the total number of particles.     

A life cycle approach to the management of household food waste - A Swedish full-scale case study

Environmental impacts from incineration, decentralised composting and centralised anaerobic digestion of solid organic household waste are compared using the EASEWASTE LCA-tool. The comparison is based on a full scale case study in southern Sweden and used input-data related to aspects such as source-separation behaviour, transport distances, etc. are site-specific. Results show that biological treatment methods - both anaerobic and aerobic, result in net avoidance of GHG-emissions, but give a larger contribution both to nutrient enrichment and acidification when compared to incineration. Results are to a high degree dependent on energy substitution and emissions during biological processes. It was seen that if it is assumed that produced biogas substitute electricity based on Danish coal power, this is preferable before use of biogas as car fuel. Use of biogas for Danish electricity substitution was also determined to be more beneficial compared to incineration of organic household waste. This is a result mainly of the use of plastic bags in the incineration alternative (compared to paper bags in the anaerobic) and the use of biofertiliser (digestate) from anaerobic treatment as substitution of chemical fertilisers used in an incineration alternative. Net impact related to GWP from the management chain varies from a contribution of 2.6 kg CO₂-eq/household and year if incineration is utilised, to an avoidance of 5.6 kg CO₂-eq/household and year if choosing anaerobic digestion and using produced biogas as car fuel. Impacts are often dependent on processes allocated far from the control of local decision-makers, indicating the importance of a holistic approach and extended collaboration between agents in the waste management chain.     

Environmental impact assessment of the incineration of municipal solid waste with auxiliary coal in China

The environmental impacts of waste incineration with auxiliary coal were investigated using the life-cycle-based software, EASEWASTE, based on the municipal solid waste (MSW) management system in Shuozhou City. In the current system, MSW is collected, transported, and incinerated with 250kg of coal per ton of waste. Based on observed environmental impacts of incineration, fossil CO(2) and heavy metals were primary contributors to global warming and ecotoxicity in soil, respectively. Compared with incinerators using excess coal, incineration with adequate coal presents significant benefits in mitigating global warming, whereas incineration with a mass of coal can avoid more impacts to acidification, photochemical ozone and nutrient enrichment because of increased electricity substitution and reduced emission from coal power plants. The "Emission standard of air pollutants for thermal power plants (GB13223-2011)" implemented in 2012 introduced stricter policies on controlling SO(2) and NO(x) emissions from coal power plants. Thus, increased use of auxiliary coal during incineration yields fewer avoided impacts on acidification and nutrient enrichment. When two-thirds of ash is source-separated and landfilled, the incineration of rest-waste presents better results on global warming, acidification, nutrient enrichment, and even ecotoxicity in soil. This process is considered a promising solution for MSW management in Shuozhou City. Weighted normalized environmental impacts were assessed based on Chinese political reduction targets. Results indicate that heavy metal and acidic gas emissions should be given more attention in waste incineration. This study provides scientific support for the management of MSW systems dominated by incineration with auxiliary coal in China.     

Quantifying capital goods for waste incineration

Materials and energy used for the construction of modern waste incineration plants were quantified. The data was collected from five incineration plants (72,000–240,000 tonnes per year) built in Scandinavia (Norway, Finland and Denmark) between 2006 and 2012. Concrete for the buildings was the main material used amounting to 19,000–26,000 tonnes per plant. The quantification further included six main materials, electronic systems, cables and all transportation. The energy used for the actual on-site construction of the incinerators was in the range 4000–5000 MW h. In terms of the environmental burden of producing the materials used in the construction, steel for the building and the machinery contributed the most. The material and energy used for the construction corresponded to the emission of 7–14 kg CO₂ per tonne of waste combusted throughout the lifetime of the incineration plant. The assessment showed that, compared to data reported in the literature on direct emissions from the operation of incinerators, the environmental impacts caused by the construction of buildings and machinery (capital goods) could amount to 2–3% with respect to kg CO₂ per tonne of waste combusted.     

Home composting as an alternative treatment option for organic household waste in Denmark: An environmental assessment using life cycle assessment-modelling

An environmental assessment of the management of organic household waste (OHW) was performed from a life cycle perspective by means of the waste-life cycle assessment (LCA) model EASEWASTE. The focus was on home composting of OHW in Denmark and six different home composting units (with different input and different mixing frequencies) were modelled. In addition, incineration and landfilling was modelled as alternatives to home composting. The most important processes contributing to the environmental impact of home composting were identified as greenhouse gas (GHG) emissions (load) and the avoided emissions in relation to the substitution of fertiliser and peat when compost was used in hobby gardening (saving). The replacement of fertiliser and peat was also identified as one of the most sensible parameters, which could potentially have a significant environmental benefit. Many of the impact categories (especially human toxicity via water (HTw) and soil (HTs)) were affected by the heavy metal contents of the incoming OHW. The concentrations of heavy metals in the compost were below the threshold values for compost used on land and were thus not considered to constitute a problem. The GHG emissions were, on the other hand, dependent on the management of the composting units. The frequently mixed composting units had the highest GHG emissions. The environmental profiles of the home composting scenarios were in the order of −2 to 16 milli person equivalents (mPE) Mg⁻¹ wet waste (ww) for the non-toxic categories and −0.9 to 28 mPE Mg⁻¹ ww for the toxic categories. Home composting performed better than or as good as incineration and landfilling in several of the potential impact categories. One exception was the global warming (GW) category, in which incineration performed better due to the substitution of heat and electricity based on fossil fuels.     

Life cycle assessment of solid refuse fuel production from MSW in Korea

Solid refuse fuel (SRF) produced from waste materials is a promising fuel that can be utilized for energy recovery in industries. This study considered both characterization and weighting modeling as life cycle assessment (LCA) results. This study aimed to analyze the flows of materials and energy and to evaluate the environmental impact of SRF plants using LCA and compared them with an incineration plant. Based on the results of material and energy flow analysis, SRF products had various energy potentials depending on the treatment method of municipal solid waste (MSW) and replaced the current fossil fuels by SRF combustion. Global impacts were mainly influenced by energy consumption, especially drying methods in the production of SRF, and affected the results of the weighting analysis. The SRF plant with a bio-drying option was evaluated as the best effective practice in the weighting analysis. The LCA results in this study indicated 0.021–9.88 points according to drying methods for SRF production and 1.38 points for incineration. In the sensitivity analysis, the environmental impact of SRF production was found to be significantly affected by the drying methods for MSW and the utilization of fossil energy. Thus, improvement of the drying options could significantly reduce the environmental impact.     

Mitigation of global greenhouse gas emissions from waste: conclusions and strategies from the Intergovernmental Panel on Climate Change (IPCC) Fourth Assessment Report. Working Group III (Mitigation).

Greenhouse gas (GHG) emissions from post-consumer waste and wastewater are a small contributor (about 3%) to total global anthropogenic GHG emissions. Emissions for 2004-2005 totalled 1.4 Gt CO2-eq year(-1) relative to total emissions from all sectors of 49 Gt CO2-eq year(-1) [including carbon dioxide (CO2), methane (CH4), nitrous oxide (N2O), and F-gases normalized according to their 100-year global warming potentials (GWP)]. The CH4 from landfills and wastewater collectively accounted for about 90% of waste sector emissions, or about 18% of global anthropogenic methane emissions (which were about 14% of the global total in 2004). Wastewater N2O and CO2 from the incineration of waste containing fossil carbon (plastics; synthetic textiles) are minor sources. Due to the wide range of mature technologies that can mitigate GHG emissions from waste and provide public health, environmental protection, and sustainable development co-benefits, existing waste management practices can provide effective mitigation of GHG emissions from this sector. Current mitigation technologies include landfill gas recovery, improved landfill practices, and engineered wastewater management. In addition, significant GHG generation is avoided through controlled composting, state-of-the-art incineration, and expanded sanitation coverage. Reduced waste generation and the exploitation of energy from waste (landfill gas, incineration, anaerobic digester biogas) produce an indirect reduction of GHG emissions through the conservation of raw materials, improved energy and resource efficiency, and fossil fuel avoidance. Flexible strategies and financial incentives can expand waste management options to achieve GHG mitigation goals; local technology decisions are influenced by a variety of factors such as waste quantity and characteristics, cost and financing issues, infrastructure requirements including available land area, collection and transport considerations, and regulatory constraints. Existing studies on mitigation potentials and costs for the waste sector tend to focus on landfill CH4 as the baseline. The commercial recovery of landfill CH4 as a source of renewable energy has been practised at full scale since 1975 and currently exceeds 105 Mt CO2-eq year(-1). Although landfill CH4 emissions from developed countries have been largely stabilized, emissions from developing countries are increasing as more controlled (anaerobic) landfilling practices are implemented; these emissions could be reduced by accelerating the introduction of engineered gas recovery, increasing rates of waste minimization and recycling, and implementing alternative waste management strategies provided they are affordable, effective, and sustainable. Aided by Kyoto mechanisms such as the Clean Development Mechanism (CDM) and Joint Implementation (JI), the total global economic mitigation potential for reducing waste sector emissions in 2030 is estimated to be > 1000 Mt CO2-eq (or 70% of estimated emissions) at costs below 100 US$ t(-1) CO2-eq year(-1). An estimated 20-30% of projected emissions for 2030 can be reduced at negative cost and 30-50% at costs < 20 US$ t(-) CO2-eq year(-1). As landfills produce CH4 for several decades, incineration and composting are complementary mitigation measures to landfill gas recovery in the short- to medium-term--at the present time, there are > 130 Mt waste year(-1) incinerated at more than 600 plants. Current uncertainties with respect to emissions and mitigation potentials could be reduced by more consistent national definitions, coordinated international data collection, standardized data analysis, field validation of models, and consistent application of life-cycle assessment tools inclusive of fossil fuel offsets.     

Economic assessment and energy model scenarios of municipal solid waste incineration and gas turbine hybrid dual-fueled cycles in Thailand

Finding environmentally benign methods related to sound municipal solid waste (MSW) management is of highest priority in Southeast Asia. It is very important to study new approaches which can reduce waste generation and simultaneously enhance energy recovery. One concrete example of particular significance is the concept of hybrid dual-fuel power plants featuring MSW and another high-quality fuel like natural gas. The hybrid dual-fuel cycles provide significantly higher electrical efficiencies than a composite of separate single-fuel power plant (standalone gas turbine combined cycle and MSW incineration). Although hybrid versions are of great importance for energy conversion from MSW, an economic assessment of these systems must be addressed for a realistic appraisal of these technologies. This paper aims to further examine an economic assessment and energy model analysis of different conversion technologies. Energy models are developed to further refine the expected potential of MSW incineration with regards to energy recovery and environmental issues. Results show that MSW incineration can play role for greenhouse gas reduction, energy recovery and waste management. In Bangkok, the electric power production via conventional incineration and hybrid power plants can cover 2.5% and 8% of total electricity consumption, respectively. The hybrid power plants have a relative short payback period (5 years) and can further reduce the CO₂ levels by 3% in comparison with current thermal power plants.     

Change in MSW characteristics under recent management strategies in Taiwan

Reduction and recycling initiatives such as producer responsibility and pay-as-you-throw are being implemented in Taiwan. This paper presents a study assessing the impact of recently implemented municipal solid waste (MSW) reduction and recycling management strategies on the characteristics of waste feedstock for incineration in Taiwan. Through the periodic sampling of two typical MSW incineration plants, proximate and ultimate analyses were conducted according to standard methods to explore the influence of MSW reduction and recycling management strategies on incineration feed waste characteristics. It was observed that the annual amount of MSW generated in 2005 decreased by about 10% compared to 2003 and that the characteristics of MSW have changed significantly due to recent management strategies. The heating value of the MSW generated in Taiwan increased yearly by about 5% after program implementation. A comparison of the monthly variations in chemical concentrations indicated that the chlorine content in MSW has changed. This change results from usage reduction of PVC plastic due to the recycling fund management (RFM) program, and the food waste as well as salt content reduction due to the total recycling for kitchen garbage program. This achievement will improve the reduction of dioxin emissions from MSW incineration. In summary, management strategies must be conducted in tandem with the global trend to achieve a zero-waste-discharge country. When implementing these strategies and planning for future MSW management systems, it is important to consider the changes that may occur in the composition and characteristics of MSW over time.     

Nitrous oxide (N2O) emissions from waste and biomass to energy plants.

Following the Kyoto protocol with respect to reducing emissions of greenhouse gases emissions, and EU energy policy and sustainability in waste management, there has been an increased interest in the reduction of emissions from waste disposal operations. From the point of view of nitrous oxide (N2O) emissions, waste incineration and waste co-combustion are very acceptable methods for waste disposal. In order to achieve very low N2O emissions from waste incineration, particularly for waste with higher nitrogen content (e.g. sewage sludge), two factors are important: temperature of incineration over 900 degrees C and avoiding the selective non-catalytic reduction (SNCR) de-NO(X) method based on urea or ammonia treatments. The more modern selective catalytic reduction (SCR) systems for de-NO(X) give rise to negligible sources of N2O.     

Life-cycle-assessment of the historical development of air pollution control and energy recovery in waste incineration

Incineration of municipal solid waste is a debated waste management technology. In some countries it is the main waste management option whereas in other countries it has been disregarded. The main discussion point on waste incineration is the release of air emissions from the combustion of the waste, but also the energy recovery efficiency has a large importance.The historical development of air pollution control in waste incineration was studied through life-cycle-assessment modelling of eight different air pollution control technologies. The results showed a drastic reduction in the release of air emissions and consequently a significant reduction in the potential environmental impacts of waste incineration. Improvements of a factor 0.85–174 were obtained in the different impact potentials as technology developed from no emission control at all, to the best available emission control technologies of today (2010).The importance of efficient energy recovery was studied through seven different combinations of heat and electricity recovery, which were modelled to substitute energy produced from either coal or natural gas. The best air pollution control technology was used at the incinerator. It was found that when substituting coal based energy production total net savings were obtained in both the standard and toxic impact categories. However, if the substituted energy production was based on natural gas, only the most efficient recovery options yielded net savings with respect to the standard impacts. With regards to the toxic impact categories, emissions from the waste incineration process were always larger than those from the avoided energy production based on natural gas. The results shows that the potential environmental impacts from air emissions have decreased drastically during the last 35 years and that these impacts can be partly or fully offset by recovering energy which otherwise should have been produced from fossil fuels like coal or natural gas.     

Greenhouse gas emissions from biogenic waste treatment: options and uncertainty

A simplified life cycle assessment was conducted to estimate greenhouse gas (GHG) emissions and energy production from each component of biogenic waste treated in an open dumping site, and by composting, anaerobic digestion, and incineration employed with additional options. The impact of uncertainties and sensitivities of the parameters in the treatment methods were investigated. We conducted a sensitivity analysis to identify the most sensitive parameters, and we discussed the relationship between uncertainty and sensitivity. Our results revealed that the moisture content of food waste and the biomass-derived carbon and methane concentration of the landfill gas of biogenic waste subjected to open dumping are the most sensitive parameters across all the treatment methods. The net GHG emissions from food waste treated in an open dumping site ranged over ten times (0.30 ? 3.67 Gg CO₂ eq/Gg). In addition, by employing additional options for the open dumping site, including soil cover, a landfill gas collection system, shifting to a semi-aerobic condition, and energy conservation by using a gas engine, we found that the net GHG emissions could be reduced by 10, 27.9, 37.4 %, and up to 56.7 %, respectively. Shifting to a semi-aerobic system is the most effective method for reducing GHG emissions, followed by landfill gas collection.     

生活垃圾焚烧发电厂二恶英对人体健康的风险评价

介绍了生活垃圾焚烧过程中二恶英的产生机理、对人体的危害及控制措施,以某生活垃圾焚烧发电厂环境影响评价为例,提出了二恶英对人体健康风险评价方法,同类项目环境影响评价提供借鉴。     

Towards a coherent European approach for taxation of combustible waste

Although intra-European trade of combustible waste has grown strongly in the last decade, incineration and landfill taxes remain disparate within Europe. The paper proposes a more coherent taxation approach for Europe that is based on the principle of Pigovian taxation, i.e. the internalization of environmental damage costs. The approach aims to create a level playing field between European regions while reinforcing incentives for sustainable management of combustible waste. Three important policy recommendations emerge. First, integrating waste incineration into the European Emissions Trading System for greenhouse gases (EU ETS) reduces the risk of tax competition between regions. Second, because taxation of every single air pollutant from waste incineration is cumbersome, a differentiated waste incineration tax based on NO_x emissions can serve as a second-best instrument. Finally, in order to strengthen incentives for ash treatment, a landfill tax should apply for landfilled incineration residues. An example illustrates the coherence of the policy recommendations for incineration technologies with diverse environmental effects.     

Thermal conversion of municipal solid waste via hydrothermal carbonization: comparison of carbonization products to products from current waste management techniques

Hydrothermal carbonization (HTC) is a novel thermal conversion process that may be a viable means for managing solid waste streams while minimizing greenhouse gas production and producing residual material with intrinsic value. HTC is a wet, relatively low temperature (180-350 °C) thermal conversion process that has been shown to convert biomass to a carbonaceous residue referred to as hydrochar. Results from batch experiments indicate HTC of representative waste materials is feasible, and results in the majority of carbon (45-75% of the initially present carbon) remaining within the hydrochar. Gas production during the batch experiments suggests that longer reaction periods may be desirable to maximize the production of energy-favorable products. If using the hydrochar for applications in which the carbon will remain stored, results suggest that the gaseous products from HTC result in fewer g CO(2)-equivalent emissions than the gases associated with landfilling, composting, and incineration. When considering the use of hydrochar as a solid fuel, more energy can be derived from the hydrochar than from the gases resulting from waste degradation during landfilling and anaerobic digestion, and from incineration of food waste. Carbon emissions resulting from the use of the hydrochar as a fuel source are smaller than those associated with incineration, suggesting HTC may serve as an environmentally beneficial alternative to incineration. The type and extent of environmental benefits derived from HTC will be dependent on hydrochar use/the purpose for HTC (e.g., energy generation or carbon storage).