冷冻固定化硝化菌去除废水中氨氮的研究

采用聚乙烯醇(PVA)循环冷冻法制备固定化硝化菌颗粒,经活化后在颗粒填充率为9％的三相流化床中进行氨氮废水处理试验。处理低浓度氨氮有机废水(NH3-N质量浓度为75mg／L．COD约为400mg／L,水力停留时间为4h)时,NH3-N去除率约为90％,COD、TIN的去除率可达82％和60％左右;处理高浓度氨氮废水(NH3-N质量浓度450～500mg／L,水力停留时间为20h)时,NH3-N去除率在98％以上,氨氧化产物中NO2^--N质量分数在95％以上,为亚硝酸盐反硝化提供了有利条件。用该法制成的硝化菌颗粒寿命在3个月以上。     

Fenton氧化-生物接触氧化工艺处理甲醛和乌洛托品废水

采用Fenton氧化一生物接触氧化工艺处理含甲醛和乌洛托品的模拟废水（简称废水）,在H2O2（体积分数30％）加入量2．5g／L、H2O2与Fe^2＋质量浓度比3．75、反应时间3h、不调节废水初始pH的Fenton氧化预处理最佳操作条件下,废水COD从1000mg／L左右降至300mg／L,COD去除率达72％。原废水完全无法直接进行生化处理,经Fenton氧化预处理后其BOD,／COD约为0．5,易于生化处理。Fenton氧化一生物接触氧化工艺处理废水,生物接触氧化停留时间为12h时,废水COD去除率高达94％,处理后出水COD小于70mg／L,处理效果很好。     

混凝-催化氧化法预处理氨基C酸生产废水

采用混凝-催化氧化组合工艺预处理氨基C酸生产废水,考察了混凝剂加入量、废水pH、氧化剂加入量、反应时间和催化剂的重复使用次数等因素对废水处理效果的影响。混凝-催化氧化法预处理氨基C酸生产废水的最佳工艺条件为：质量分数为10％的FeSO4溶液作混凝剂,加入量为250InL／L;质量分数为1％的ClO2溶液作氧化剂,加入量为75mL／L;Ni／AC作催化剂,加入量为40g/L;废水pH为3．2;催化氧化反应时间为60min。在该条件下,废水的COD去除率可达78．4％,BOD,／COD由原来的0．076提高到0．292,可生化性得到明显改善。Ni／AC催化剂连续使用7次后仍保持稳定的催化活性。经济性初步分析表明,1t废水的处理成本约为16元。     

混凝-间歇式活性污泥法处理炼油废水

采用混凝-间歇式活性污泥（SBR）法处理炼油废水,考察了混凝、SBR法对炼油废水的处理效果。实验结果表明：在硫酸铝、聚丙烯酰胺、CaCl2加入量分别为50,3,100mg／L的条件下,油去除率为82．7％,COD去除率为57．1％,BOD,／COD为0．24,混凝处理出水具有一定的可生化性;对混凝处理出水用SBR法进行厌氧水解2h、好氧曝气9h的生物处理后,出水COD低于150mg／L,COD去除率在80％左右。     

活性炭/H2O2催化氧化-絮凝法预处理化工有机废水

用活性炭作催化剂、H2O2作氧化剂催化氧化预处理高浓度化工有机废水,考察了各种因素对COD去除率的影响。实验结果表明,在H2O2加入量为0．8mL／L、活性炭与H2O2质量比为0．7、废水pH为4的条件下,反应120min后,调废水pH至8,加入絮凝剂聚合氯化铝进行絮凝沉淀,废水COD去除率达70％以上,色度去除率达80％以上。通过色谱-质谱仪对处理前后废水中的有机物进行分析,初步探讨了活性炭／H2O2催化氧化-絮凝法预处理化工有机废水的作用机理。     

用水解酸化池-膜生物反应器处理活性艳红X-3B废水

采用水解酸化池-膜生物反应器处理含活性艳红X-3B的模拟废水,研究了水力停留时间（HRT）对水解酸化池废水处理效果的影响,考察了水解酸化池-膜生物反应器对废水的处理效果及膜生物反应器中污泥沉降性能对膜污染的影响。实验结果表明：水解酸化池HRT为16h时,废水的可生化性最好,挥发性脂肪酸质量浓度与COD比值为0．5;HRT为17h时,废水脱色率达69％,而COD的去除率受HRT影响较小;膜生物反应器主要起去除废水中COD的作用;水解酸化池-膜生物反应器处理后废水的脱色率和COD去除率分别为83％和97％;膜生物反应器中活性污泥沉降性能的变化直接影响膜污染的速率。     

对苯二甲酸降解菌固定化生物流化床处理精对苯二甲酸废水

采用微生物筛选、纯化技术,获得了降解对苯二甲酸（TA）的YPC—TA1,YPC—TA2,YPC-TA3,YPC—TA44株菌株。将筛选出的TA降解菌固定化,处理初始TA质量浓度为2650mg／L的模拟废水,降解36h后TA去除率达100％。用TA降解芮在生物流化床反应器中处理PTA废水,最佳容积负荷为6.7kg／（m^3·d）。生物流化床反应器可在容积负荷为6．0～6．5kg／（m^3·d）的较佳条件下长周期稳定运行,COD去除率保持在91％左右,TA去除率保持在94％左右。低pH废水冲击和高容积负荷废水冲击时COD,TA去除率均明显下降,恢复正常讲水后3～4d,COD,TA去除率均恢复正常。     

电凝聚-气浮法处理印染废水

采用电凝聚-气浮法处理模拟印染废水（简称废水）,考察了废水pH、电解电流、电解时间对废水COD去除率的影响。实验结果表明,当废水pH=6．5、电解电流为1．0A、电解时间为25min时,废水COD去除率可达90％以上。该方法具有较宽的操作范围,电解电流为1．0～1．9A,废水COD去除率相差不大;废水pH为3.45～11.46,废水COD去除率均可达80％以上。电凝聚-气浮法处理印染废水无需外加药剂,无二次污染。     

多相催化湿式氧化法处理高浓度难降解有机废水的研究

在高压反应釜内，采用自制颗粒贵金属催化剂催化湿式氧化法处理高浓度饲料抗氧化剂合成废水，探讨了温度、压力、进水pH等反应条件对废水处理效果的影响。在温度为220℃、总压为8MPa条件下，COD，TOC，TN和色度的去除率分别达到77．0％，66．1％，70．2％，91％；处理后的废水pH很低，催化剂显示出较好的耐酸性；随进水pH的增加，COD的去除率逐渐降低，出水pH增加。     

有机磷阻燃剂生产废水预处理工艺研究

采用液膜萃取—酸析沉降—络合萃取组合工艺对有机磷阻燃剂生产废水进行预处理.最佳工艺条件为:液膜萃取时,液膜油相(表面活性剂与煤油的混合液)与内水相(H2SO4溶液)的体积比2∶1、乳化液膜与废水的体积比1∶8、废水pH 13.0,硫酸体积分数10％、煤油中表面活性剂质量浓度30 g/L、液膜萃取时间 15 min;酸析沉降时,废水pH l.0,酸析沉降时间30 min;络合萃取时,络合萃取剂(烷基叔胺N235与煤油的混合液)中烷基叔胺N235体积分数30％,络合萃取剂与废水的体积比1∶4,废水pH l.0,络合萃取时间30 min.在此最佳处理条件下,废水COD总去除率可达93％,吡啶去除率达99.9％以上,总磷去除率可达97％,BOD5/COD提高至0.32,有利于后续生化处理.     

Distribution of Cd,Ck, Pb and Zn in Soil and Vegetation Compartments in Stands of Five Boreal Tree Species in N.E. Sweden

Concentrations and total quantity of cadmium (Cd), cupper (Cu),lead (Pb) and zink (Zn) were determined in biomass and soil compartments in a replicated tree species experiment with 27-yr-old stands growing on former farmland in N.E. Sweden. Sequentialextractions of soil samples were performed in order to estimate the exchangeable and an organically bound fraction of each element. The tree species included were Picea abies (L.)H. Karst., Pinus sylvestris L., Pinus contorta Dougl., Larix sibirica Ledeb., and Betula pendula Roth.Tree species influenced the rate of removal of Cu, Pb and Zn incase of stemwood harvesting, and of Cd, Cu and Zn in the case ofwhole-tree harvesting. B. pendula and P. abies had higher quantities and average concentrations of Zn in the biomass. For all species, >50% of the Zn in the stems was found in the bark. P. abies and L. sibirica had higher quantities of Cu in the biomass than the other species.P. abies and P. contorta had high quantities of Cd inthe biomass in relation to the other species. Branches and stembark contained high concentrations of Cd and Pb in relation to foliage and stemwood. Dead branches had especially high concentrations of Pb. The high accumulation rate of Zn in thebiomass of B. pendula was related to a low exchangeable amount of Zn in the A horizon. In the superficial centimeters ofthe A horizon, a depletion similar to that found for Zn was detected for Cu, whereas for Cd and Pb, no correlations were found between quantities of elements in the trees and element pools in the soil.     

Programs assessing implementation and effectiveness of state forest practice rules and BMPs in the West

The major forest nonpoint source control programs in the West are largely regulatory, either under forest practices acts (California, Idaho, New Mexico, Nevada, Oregon, and Washington) or a streamside management act (Montana). These programs and the specific rules they enforce continue to undergo intensive scrutiny. Still, the questions are the same for these regulatory programs as for states that base nonpoint source control on voluntary BMPs (Arizona, Colorado, Utah, Wyoming). Are the rules or BMPs being applied, and are they effective in reducing nonpoint source pollution to levels that protect beneficial uses of water? The level of debate about forestry in the West has resulted in detailed monitoring and research to answer these questions. In the past, state agencies have assumed levels of BMP compliance based on the percent of operations without enforcement actions. These estimates are being replaced by statistically valid and reproducible monitoring of forest practices rules and BMP compliance levels. BMP effectiveness is being assessed using both qualitative and quantitative methods. This can involve field assessments, process-based research, and control watershed studies. Some trend monitoring is also beginning. With the regional implementation rate for forestry BMPs at about 94% and rising, it is likely that effectiveness testing will continue to be a priority and consume the majority of assessment resources for this region.     

High Immobilization of NH4+ in Danish Heath Soil Related to Succession,Soil and Nutrients: Implications for Critical Loads of N

During recent decades heathlands havechanged into grasslands in regions with high atmosphericnitrogen deposition. In regions with intermediatedeposition level (e.g., Denmark) changes have been lesspronounced which may be due to delay or decrease inresponse of the ecosystem. The mor layer (O horizon) mayplay an important role for this delay due to high sinkstrength for N. In this study, the capacity for netNH₄ ⁺ immobilization and mineralization wasstudied during short- and long-term incubations (2–36 days)of mor samples from Danish dry inland heaths. High short-term capacity for net NH₄ ⁺ immobilization wasfound to be a general characteristic of Danish heath morlayers both under heather (Calluna vulgaris) andcrowberry (Empetrum nigrum ssp nigrum), the latterdominating late stages in heathland succession. The netNH₄ ⁺ immobilization was higher under youngcompared to old or dead vegetation, and higher on lessnutrient poor soils than on extremely nutrient poor soils.The addition of N, P and C stimulated CO₂ productionand net NH₄ ⁺ immobilization, but not net Nmineralization. The immobilization of ¹⁵NH₄ ⁺caused release of dissolved organic N, increased N anddecreased C/N ratio in the microbial biomass, and indicatedgrowth of microorganisms with other metabolic abilitiesthan the indigenous population. No evidence was obtained ofstabilization of immobilized ¹⁵NH₄ ⁺ intosoil organic matter during the experiment. On background ofthe results and current knowledge it was concluded that therecognition of the high capacity for net NH₄ ⁺immobilization in mor layers does not allow for a raiseof critical loads for N for northern dry inland heaths.     

Starch-plastic materials—Preparation,physical properties,and biodegradability (a review of recent USDA research)

Recent starch-plastic research at the National Center for Agricultural Utilization Research is reviewed and related worldwide efforts are noted. Properties of starch that influence its formulation and performance in plastics are discussed. Methods are given for preparation of starch-poly(methyl acrylate) graft copolymer, starch-poly(ethylene-co-acrylic acid), and starch-poly(ethylene-co-acrylic acid)-polyethylene plastics. Their physical properties are discussed, as is degradability by enzymes or amylolytic organisms from soil, ponds, and streams.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Application of Cellulose Microfibrils in Polymer Nanocomposites

Cellulose microfibrils obtained by the acid hydrolysis of cellulose fibers were added at low concentrations (2–10% w/w) to polymer gels and films as reinforcing agents. Significant changes in mechanical properties, especially maximum load and tensile strength, were obtained for fibrils derived from several cellulosic sources, including cotton, softwood, and bacterial cellulose. For extruded starch plastics, the addition of cotton-derived microfibrils at 10.3% (w/w) concentration increased Young’s modulus by 5-fold relative to a control sample with no cellulose reinforcement. Preliminary data suggests that shear alignment significantly improves tensile strength. Addition of microfibrils does not always change mechanical properties in a predictable direction. Whereas tensile strength and modulus were shown to increase during addition of microfibrils to an extruded starch thermoplastic and a cast latex film, these parameters decreased when microfibrils were added to a starch–pectin blend, implying that complex interactions are involved in the application of these reinforcing agents.     

四氮唑废水处理工艺设计

高浓度、高盐分的四氮唑生产废水通过三效蒸发浓缩,馏出液经铁炭氧微电解和混凝预处理,再采用水解酸化一接触氧化一反应二沉主体组合工艺进行处理。研究了该工艺所需构筑物和设备的设计与选型。该工艺在正常运行条件下,处理后出水pH6～9,COD 302mg／L,BOD5 108mg／L,SS30mg／L,色度36倍,水质达到GB8978--1996（污水综合排放标准》三级标准。     

Hysteresis in Reversal of Central European Mountain Lakes from Atmospheric Acidification

Extremely high emissions of S and N compounds in Central Europe (both 280 mmol m^-2 yr^-1) declined by 70and 35%, respectively, during the last decade. Decreaseddeposition rates of SO₄ ^-2, NO₃ ^-, and NH₄ ⁺ in the region paralleled emission declines. The reduction in atmospheric inputs of S and N to mountain ecosystemshas resulted in a pronounced reversal of acidification in the Tatra Mountains and Bohemian Forest lakes. Between the 1987–1990and 1997–1999 periods, concentrations of SO₄ ^-2 and NO₃ ^- decreased (average ± standard deviation) by 22±7 and 12±7 mol L^-1, respectively, in theTatra Mountains, and by 19±7 and 15±10 mol L^-1, respectively, in the Bohemian Forest. Their decrease was compensated in part (1) by a decrease in Ca²⁺ + Mg²⁺ (17±7 mol L^-1) and H⁺ (4±6 mol L^-1), and an increase in HCO₃ ^-(10±10 mol L^-1) in the Tatra Mountains lakes, and (2) by a decrease in Al (7±4 mol L^-1), Ca²⁺ + Mg²⁺ (9±6 mol L^-1), and H⁺ (6±5 mol L^-1), in Bohemian Forest lakes. Despite the rapid decline in lake water concentrations of SO₄ ^-2 and NO₃ ^- in response to reduced S and N emissions, their present concentrations in some lakes are higher than predictionsbased on observed concentrations at comparable emission rates during development of acidification. This hysteresis in chemical reversal from acidification has delayed biological recovery of the lakes. The only unequivocal sign of biological recovery hasbeen observed in erné Lake (Bohemian Forest) where a cladoceran species Ceriodaphnia quadrangular has recentlyreached its pre-acidification abundance.     

Reconstruction of Long-Term Changes in Lake water Chemistry,Zooplankton and Benthos of a Small,Acidified High-Mountain Lake: Magic Modelling and Palaeolimnogical Analysis

Starolesnianske pleso is a small and shallow acid lake in the High Tatra Mountains, situated at 2000 m above sea level, on granitic bedrock, with sparse and thin soil cover. When detailed measurements began in the 1980s Starolesnianske pleso had pH below 5 and only one species of cladoceran zooplankton, the ubiquitous Chydorus sphaericusPalaeolimnological investigations show changes in cladoceran zooplankton and chironomid zoobenthic assemblages since about 1920 and a major change in 1970–1980. The dynamic acidification model MAGIC was used to reconstruct changes in water chemistry over the past 150 years. The results from MAGIC agree well with the sediment record; pH levels gradually decreased from 6.5 in the mid-1800s to about 5.6 in 1920 (first response in biota) to below 5.0 by 1970, and concentrations of inorganic aluminium rose dramatically beginning about 1960. In the 1990s the lake water chemistry showed clear signs of reversal in acidification brought about by a major decline in S deposition.     

Does Soil Acidification Affect Spruce Needle Chemical Composition and Tree Growth?

In 1994, a large survey of soil chemistry was undertaken in thecounty of Värmland in central Sweden (Lundström et al., 1998).The southern part of the county was affected by soilacidification whereas there were no such indications in thenorthern part. To investigate the influence of soil chemistryon the trees at the specific sites, the survey was continued byan analysis of needle chemistry (Norway spruce) which wasundertaken at 150 of the 180 sites, and of tree growth at 65 ofthe 180 sites. Growth was expressed as a ratio between expectedgrowth, estimated with a national, empirical growth model, andthe growth observed in the field. In statistical analyses,using rank correlation, PCA and PLS, there were only weakindications of an influence of soil chemistry on needlechemistry and on tree growth. A moderate correlation betweennitrogen and sulphur in needles was found, which wasinterpreted as an effect of deposition and of processes in thetree canopy. No obvious regional pattern of the growth ratiowas found, in contrast to the clear pattern of soilacidification. The statistical analysis could not with anycertainty point out any of the soil chemistry variables asespecially important for the tree growth ratio.     

Heavy Metals Removal by Biosorption and Flotation

The removal of a mixture of heavy (toxic) metal cations (copper, nickeland zinc) from liquid effluents was investigated in this study at pilotscale, using counter-current contact mode. The innovative processinvolved the abstraction of metal ions onto fungal biosorbents, followedby the application of flotation for the subsequent solid/liquid separationof biomass particles. The ability of microorganisms to remove metal ionsfrom aqueous solutions is a well-known phenomenon. Nevertheless,engineering considerations are very important in decisions, concerningthe commercial future of biosorption and practical solutions are neededfor certain problems, such as the efficient post-separation ofmetal-loaded biomass. The two processes (flotation and biosorption) caneffectively operate in combination, in what it was termed biosorptiveflotation process. The sorbents may be recycled, after appropriate elutionof metals, as well as the treated (clean) water.