上海市生活垃圾综合处理工艺研究

针对城市垃圾含水率高、成分复杂的特点,采用静置沥水5天后再筛分处理的措施,垃圾的含水率可去除10％～15％,增强了机械分选效果。对筛下物进行生物堆肥处理,两次发酵约35天后,产品基本达到无害化、稳定化的要求。同时,对筛上物进行了卫生填埋,渗滤液经过沉淀和UASB工艺预处理后与邻近污水厂污水合并处理,臭气经生物滤池后也得到有效控制。     

Composting and compost application in China

The current situation of municipal solid waste (MSW) and sewage sludge production (in terms of volume as well as composition) in China is introduced. Composting and compost application in China are reviewed. In China, the production of municipal solid waste and sewage sludge is changing rapidly along with economic development. Composting is mainly applied for treating MSW, about 20% of the total amount of MSW being disposed. MSW composting is mainly co-composted with night soil or sewage sludge. Compost is used in agriculture, forestry and horticulture. Compost application is the key factor influencing the composting development in China. To promote composting and compost application in China, a state-wide survey on the production, composition and physical and chemical properties of MSW and sewage sludge should be carried out. More effort should be made to develop low cost and high efficient composting technologies according to China's conditions. The environmental impact of compost application should also be given more attention.     

Optimizing the treatment and disposal of municipal solid wastes using mathematical programming—A case study in a Greek region

Goal of the work is to present a simplified methodology to optimize an integrated solid waste management system. The methodology performs two optimizations, namely: (i) minimization of the total cost of the MSW system and (ii) minimization of the equivalent carbon dioxide emissions (CO_2e) generated by the whole system. The methodology is modeled via non-linear mathematical equations, uses 32 decision variables and does not require complex LCA databases. The proposed model optimally allocates eight MSW components (paper, cardboard, plastics, metals, glass, food wastes, yard wastes and other wastes) to four MSW management technologies (incineration, composting, anaerobic digestion, and landfilling) after source separation of recyclables has taken place. The Region of East-Macedonia and Thrace in Greece was selected as a case study. Results showed that there is a trade off between cost and CO_2e emissions. Incineration and composting were favored as the principal treatment technologies, while landfilling was always the least desirable management technology under both objective functions. The recycling participation rate significantly affected all optimum scenarios.     

Does municipal solid waste composting make economic sense?

Currently there is widespread interest on the part of local Governments in incorporating municipal solid waste (MSW) composting into their integrated solid waste management systems. However, there is little information on the costs of MSW composting and how those costs compare with the costs of alternative forms of waste disposal (especially traditional land disposal). This article begins to fill this information gap by reporting the results of a survey of 19 MSW composting facilities around the United States. Results indicate that MSW composting generally costs around $50 per ton, and that very few facilities receive any revenues from the sale of compost to offset operating costs. Additional economic analysis indicates that, at present, MSW composting cannot be justified on financial grounds in most parts of the US, but may be competitive with land disposal where the cost of landfilling is high (such as the north-east).1998 Academic Press     

Management of urban solid waste: Vermicomposting a sustainable option

Solid waste management is a worldwide problem and it is becoming more and more complicated day by day due to rise in population, industrialization as well as changes in our life style. Presently most of the waste generated is either disposed of in an open dump in developing countries or in landfills in the developed ones. Landfilling as well as open dumping requires lot of land mass and could also result in several environmental problems. Land application of urban/municipal solid waste (MSW) can be carried out as it is rich in organic matter and contains significant amount of recyclable plant nutrients. The presence of heavy metals and different toxics substances restricts its land use without processing. Vermicomposting of MSW, prior to land application may be a sustainable waste management option, as the vermicast obtained at the end of vermicomposting process is rich in plant nutrients and is devoid of pathogenic organism. Utilization of vermicast produced from urban/municipal solid waste in agriculture will facilitate in growth of countries economy by lowering the consumption of inorganic fertilizer and avoiding land degradation problem. Vermicomposting of urban/MSW can be an excellent practice, as it will be helpful in recycling valuable plant nutrients. This review deals with various aspects of vermicomposting of MSW.     

Environmental assessment of two home composts with high and low gaseous emissions of the composting process

A Life Cycle Assessment (LCA) of two home composts with low and high gaseous emissions of the composting process is presented. The study focused on the gaseous emissions of the composting process. Gaseous emissions of methane, nitrous oxides, ammonia and volatic organic compounds of the composting process were experimentally measured in field real trials. The results showed that the differences in gaseous emissions between the two home composts were 4.5, 5.8 and 52 for methane, nitrous oxides and ammonia, respectively. Higher emissions of nitrous oxides and methane affected significantly the category of global warming potential, while higher emissions of ammonia affected mainly the categories of acidification potential, eutrophication potential and photochemical oxidation. The differences found in the compost emissions were attributable to the composting production management (quality and composition of waste stream, frequency mixing of waste, humidity and temperature monitoring, among others) as well as weather conditions (temperature and humidity).     

城市垃圾和污水脱水污泥、排水管污泥混合堆肥工艺研究

城市垃圾和污水脱水污染、排水管污泥已成为现代城市污染的主要总是。由于这些废弃物中有机物质的含量较高,因此可以利用堆肥的方法来进行处理,使其转化为农田的有机肥料,本文用城市生活垃圾和污水处理厂污泥、排水管污泥混合进行堆肥的研究。     

Municipal solid waste production and composition in Finland—Changes in the period 1960–2002 and prospects until 2020

Waste reduction was recognised as the main goal of waste management policy in the EU in the 1990s. Although knowledge of past waste generation is essential for effective waste reduction policy there are no comprehensive statistics on the past development of municipal solid waste (MSW) production. MSW management is currently under turmoil in many EU countries as the requirements of the EC landfill directive (1999/31/EC) are set into force. In this study, the production and composition of MSW in Finland between 1960 and 2002 is presented using historical data. The impact of population, affluence and technology on MSW production are analysed using the IPAT equation and three scenarios are constructed until year 2020. The results are compared with national future targets on MSW production. Production of MSW increased in Finland until 1990, declined to year 1997, increased to 2000 and then declined again. The share of organic and plastic waste increased over the study period while the share of paper and cardboard declined. The results suggest that so far national targets on MSW reduction have been set fairly low. Moreover, our scenarios depict a wide range of future MSW production, even though the time horizon is not longer than 15 years into the future. In order to narrow this range, continuous improvement of the statistics of MSW is essential.     

城市垃圾填埋场渗滤液处理工艺综述

城市垃圾对环境的影响越来越严重，垃圾填埋导致垃圾渗滤液的大量产生，渗滤液中含有大量的有机物、大量的病菌、病毒、寄生虫等以及一些有毒有害的物质，若渗滤液不加以妥善处理、肆意排放，必将对地下水、地表水构成严重威胁，因此垃圾渗滤液的有效处理就成为一个亟待解决的问题。本文对城市垃圾填埋场渗滤液的处理工艺进行了分析和探讨，介绍了国内外垃圾渗滤液处理的主要技术，包括土地处理法、生物法和物化法，并对电解法处理垃圾渗滤液进行了详细的介绍。     

Performance assessment for municipal solid waste collection in Taiwan

Collecting municipal solid waste (MSW) is a major and expensive task for local waste management authorities, thus efficient MSW collection is a necessity. This study presents a procedure for developing an aggregate indicator (AI) to assess MSW collection efficiency based on multiple factors. The applicabilities of various key performance indicators (KPIs) are evaluated based on five selection criteria, and five KPIs are chosen to form the AI. The relative efficiencies of local MSW collection services are analyzed by the data envelopment analysis (DEA) method. A set of common weights for all five KPIs is then generated based on DEA results and four selection rules by modifying a previous approach. Finally, the proposed AI is applied to assess the MSW collection services provided by 307 local governments in Taiwan, and associated results are compared and discussed.     

浅论城市生活垃圾的资源化系统

现在社会产生越来越多,组份越来越复杂的生活垃圾,已成为严重的环境和社会问题。本文通过对垃圾成份和数量的分析,结果国内外垃圾处理的发展现状,针对四川省省情,提出了加强垃圾分类收集、分选回收,以堆肥、焚烧、再生等手段实现垃圾的资源化系统。并且,对目前的垃圾处理所涉及到的政府职能和社会意识等软环境作了简单描述。     

Exploring full cost accounting approach to evaluate cost of MSW services in India

Municipal solid waste (MSW) services of developing countries often suffer due to the lack of financial and operational autonomy, scientific approach, and adequate levels of resources. The solid waste management (SWM) practices of developed countries are benefited in cost and efficiency due to the participation of private players and sound financial management. However, developing economies depend on local municipalities to own and operate SWM services amidst structural and financial inefficiency. With the demands of augmenting efficient and cost-effective SWM services to the expanding population of cities and towns of newly industrialized nations on the rise, the municipalities in these countries are under pressure to adopt ways and means that can support efficient utilization of resources and improved decision-making capabilities. This research article reflects the current state of the MSW services in India and explores full cost accounting (FCA) framework in its ability to generate information on cost-related aspects and sustainable deployment of resources. Lastly, the extensibility of FCA is tested by integrating externalities of MSW services.     

Regionalization of Municipal Solid Waste Management in Japan: Balancing the Proximity Principle with Economic Efficiency

The proximity principle—disposing of waste close to its origin—has been a central value in municipal solid waste (MSW) management in Japan for the last 30 years and its widespread adoption has helped resolve numerous “Not in My Backyard” issues related to MSW management. However, MSW management costs have soared, in large part because of aggressive recycling efforts and because most MSW is incinerated in a country that has scarce landfill capacity. In addition, smaller, less sophisticated incinerators have been closed because of high dioxin emissions. Rising costs combined with the closure of smaller incinerators have shifted MSW management policy toward regionalization, which is the sharing of waste management facilities across municipalities. Despite the increased use of regionalized MSW facilities, the proximity principle remains the central value in Japanese MSW management. Municipal solid waste management has become increasingly regionalized in the United States, too, but different driving forces are at work in these two countries. The transition to regionalized MSW management in Japan results from strong governmental control at all levels, with the central government providing funds and policy direction and prefectures and municipalities being the primary implementing authorities. By contrast, market forces are a much stronger force with US MSW management, where local governments—with state government oversight—have primary responsibility for MSW management. We describe recent changes in Japan’s MSW programs. We examine the connections between MSW facility regionalization, on the one hand, and, on the other hand, the proximity principle, coordination among local governments, central government control, and financing mechanisms.     

Urban air pollution from the open burning of municipal solid waste

This study estimates the contribution from the open burning of municipal wastes in some of Nigeria's major cities to atmospheric levels of air pollutants. Information obtained on open burning emission factors and municipal solid waste (MSW) generation estimates was combined to estimate annual levels of the pollutants from the open burning of MSW. Per capita distributions of pollutants were calculated on the basis of cities’ populations. The estimates of inorganic emissions across the cities studied were from 913.73 to 81,600 tons per year (TPY) of particulate matter; 4,797 to 428,400 TPY of oxides of nitrogen; 342.65 to 30,600; and 57 to 5,100 TPY of sulfur dioxide, while the estimates for methane ranged from 742 to 66,300 TPY and for other nonmethane organic compounds ranged from 1,713 to 153,000 TPY. Given the composition of MSW in these cities, the nonmethane organic compounds are likely to be composed of polycyclic aromatic hydrocarbons and volatile organic compounds. Given the wide varieties of both inorganic and organic air pollutants released during the open burning of MSW and the associated human health and environmental impacts, it is high time that stakeholders at all levels of government came up with policies and regulatory measures for the management of MSW in the country.     

Municipal solid waste generation in Kathmandu, Nepal

Waste stream characteristics must be understood to tackle waste management problems in Kathmandu Metropolitan City (KMC), Nepal. Three-stage stratified cluster sampling was used to evaluate solid waste data collected from 336 households in KMC. This information was combined with data collected regarding waste from restaurants, hotels, schools and streets. The study found that 497.3 g capita(-1) day(-1) of solid waste was generated from households and 48.5, 113.3 and 26.1 kg facility(-1) day(-1) of waste was generated from restaurants, hotels and schools, respectively. Street litter measured 69.3 metric tons day(-1). The average municipal solid waste generation rate was 523.8 metric tons day(-1) or 0.66 kg capita(-1) day(-1) as compared to the 320 metric tons day(-1) reported by the city. The coefficient of correlation between the number of people and the amount of waste produced was 0.94. Key household waste constituents included 71% organic wastes, 12% plastics, 7.5% paper and paper products, 5% dirt and construction debris and 1% hazardous wastes. Although the waste composition varied depending on the source, the composition analysis of waste from restaurants, hotels, schools and streets showed a high percentage of organic wastes. These numbers suggest a greater potential for recovery of organic wastes via composting and there is an opportunity for recycling. Because there is no previous inquiry of this scale in reporting comprehensive municipal solid waste generation in Nepal, this study can be treated as a baseline for other Nepalese municipalities.     

Evaluation of extracted organic carbon and microbial biomass as stability parameters in ligno-cellulosic waste composts

Extracted organic C and microbial biomass were evaluated as stability parameters in 3 different ligno-cellulosic waste composts. Organic C was extracted by both water and alkali and further separated in humic-like carbon (HLC) and nonhumic carbon (NHC). Conventional humification parameters, such as humification index and degree of humification were calculated from NHC and HLC. Microbial biomass carbon (B(C)) was determined as an indicator of the degree of biochemical transformation, whereas ninhydrin reactive N (B(NIN)) was measured to obtain the stability parameter B(NIN)/N(TOT) (N(TOT), total N). The water-extracted organic C did not provide reliable information on the transformations underwent by the ligno-cellulosic wastes during composting, since its content remained almost unaltered during the whole process. In contrast, parameters based on the alkali-extracted organic C and microbial biomass clearly reflected organic matter (OM) changes during the process. There was an increase in the net amount of HLC in the alkali extracts throughout composting, especially in the first 7 to 12 wk of the process, as well as a relative enrichment of HLC with respect to NHC. Values of humification index and degree of humification in end products were consistent with an adequate level of compost stability. The stability parameter B(NIN)/N(TOT) showed to be a reliable indicator of stability in ligno-cellulosic wastes. Parameters based on the alkali-extracted C and microbial biomass clearly reflected the transformation of the OM during composting and can be used as stability parameters in ligno-cellulosic waste composts.     

A simple numerical model for predicting organic matter decomposition in a fed-batch composting operation

Using dog food as a model of the organic waste that comprises composting raw material, the degradation pattern of organic materials was examined by continuously measuring the quantity of CO2 evolved during the composting process in both batch and fed-batch operations. A simple numerical model was made on the basis of three suppositions for describing the organic matter decomposition in the batch operation. First, a certain quantity of carbon in the dog food was assumed to be recalcitrant to degradation in the composting reactor within the retention time allowed. Second, it was assumed that the decomposition rate of carbon is proportional to the quantity of easily degradable carbon, that is, the carbon recalcitrant to degradation was subtracted from the total carbon remaining in the dog food. Third, a certain lag time is assumed to occur before the start of active decomposition of organic matter in the dog food; this lag corresponds to the time required for microorganisms to proliferate and become active. It was then ascertained that the decomposition pattern for the organic matter in the dog food during the fed-batch operation could be predicted by the numerical model with the parameters obtained from the batch operation. This numerical model was modified so that the change in dry weight of composting materials could be obtained. The modified model was found suitable for describing the organic matter decomposition pattern in an actual fed-batch composting operation of the garbage obtained from a restaurant, approximately 10 kg d(-1) loading for 60 d.     

Solid Waste Treatment as a High-Priority and Low- Cost Alternative for Greenhouse Gas Mitigation

The increased concern about environmental problems caused by inadequate waste management, as well as the concern about global warming, promotes actions toward a sustainable management of the organic fraction of the waste. Landfills, the most common means to dispose of municipal solid waste (MSW), lead to the conversion of the organic waste to biogas, containing about 50% methane, a very active greenhouse gas (GHG). One unit of methane has a global warming potential of 21 computed for a 100-year horizon or 56 computed for 20 years. The waste sector in Israel contributes 13% of total greenhouse gases (GHG) emissions for a time horizon of 100 years (for a time horizon of 20 years, the waste sector contribution equals to more than 25% of total GHG emissions). The ultimate goal is to minimize the amount of methane (CH₄) by converting it to CO₂. This can be achieved by physicochemical means (e.g., landfill gas flare, incineration) or by biological processes (e.g., composting, anaerobic digestion). Since the waste in Israel has a high organic material content, it was found that the most cost-effective means to treat the degradable organic components is by aerobic composting (investment of less than US$ 10 to reduce emission of one ton CO₂ equivalent per year). Another benefit of this technology is the ability to implement it within a short period. The suggested approach, which should be implemented especially in developing countries, could reduce a significant amount of GHG at relatively low cost and short time. The development of a national policy for proper waste treatment can be a significant means to abate GHG emissions in the short term, enabling a gain in time to develop other means for the long run. In addition, the use of CO₂ quotas will credit the waste sector and will promote profitable proper waste management.     

Comparison of heavy metals content in compost against vermicompost of organic solid waste: Past and present

Disposal of the municipal organic solid waste is a serious problem worldwide. Composting is one of the most preferred methods of solid waste management practice, principally due to the high percentage of organic material in the waste composition. Composting has advantages over land-filling and incineration in Mauritius because of lower operational costs, less environmental pollution, beneficial use of the end product, high humidity and organic content of household waste. Vermicomposting is a comparatively enhanced method in composting, and involves the stabilization of organic solid waste through earthworm consumption that converts the waste into earthworm castings. In both composting and vermicomposting processes, the presence of heavy metals and different toxics substances limits its land use without processing. The production and application of compost potentially contaminate the environment with heavy metals. There is a high-degree of consensus in the past and present literatures that composting increases metal concentrations but whether similar changes in metal concentration and availability occur during vermicomposting has not been fully resolved. This review deals with various total metal contents present in composting compared to that present in vermicomposting of organic solid wastes from past and present years.     

Environmental and economic aspects of production and utilization of RDF as alternative fuel in cement plants: A case study of Metro Vancouver Waste Management

Municipal solid waste (MSW) disposal and management is one of the most significant challenges faced by urban communities around the world. Municipal solid waste management (MSWM) over the years has utilized many sophisticated technologies and smart strategies. Municipalities worldwide have pursued numerous initiatives to reduce the environmental burden of the MSW treatment strategies. One of the most beneficial MSWM strategies is the thermal treatment or energy recovery to obtain cleaner renewable energy from waste. Among many waste-to-energy strategies, refuse-derived fuel (RDF) is a solid recovered fuel that can be used as a substitute for conventional fossil fuel. The scope of this study is to investigate the feasibility of RDF production with MSW generated in Metro Vancouver, for co-processing in two cement kilns in the region. This study investigates environmental impacts and benefits and economic costs and profits of RDF production. In addition, RDF utilization as an alternative fuel in cement kilns has been assessed. Cement manufacturing has been selected as one of the most environmentally challenged industries and as a potential destination for RDF to replace a portion of conventional fossil fuels with less energy-intensive fuel. A comprehensive environmental assessment is conducted using a life cycle assessment (LCA) approach. In addition, cost–benefit analysis (CBA) has been carried out to study the economic factors. This research confirmed that RDF production and use in cement kilns can be environmentally and economically viable solution for Metro Vancouver.