Enhanced photocatalytic degradation of VOCs using Ln3+-TiO2 catalysts for indoor air purification

Two types of lanthanide ion-doped titanium dioxide (Ln3+-TiO2) catalysts including La3+-TiO2 and Nd3+-TiO2 were prepared by a sol-gel method. The effects of the lanthanide ion doping on the crystal structure, surface area, adsorption properties, pore size distribution, and surface chemical state of the catalysts were investigated by means of XRD, BET, and XPS. As results, the crystal size decreased significantly, while the specific surface area, t-plot total surface area, micropore volume, and the total pore volume increased owing to the lanthanide ion doping. The nitrogen adsorption-desorption isotherms of the catalysts showed that the N2 adsorption ability of the Ln3+-TiO2 catalysts was better than the TiO2 catalyst. Among them, the 0.7% Ln3+-TiO2 catalysts demonstrated the highest adsorption ability. The photocatalytic activity of the catalysts was investigated in the experiments of the photocatalytic degradation of benzene, toluene, ethylbenzene and o-xylene (BTEX) in a gaseous phase. The photocatalytic efficiency of the TiO2 catalysts with the lanthanide ion doping was remarkably enhanced by BTEX removal. The 1.2% Ln3+-TiO2 catalysts achieved the highest photocatalytic activity. The enhanced photodegradation of BTEX is possibly due to the improved adsorption ability and the enhanced electron-hole pairs separation due to the presence of Ti3+ on the surface of Ln3+-TiO2 catalysts and the electron transfer between the conduction band/defect level and lanthanide crystal field state.     

Enhanced photocatalytic activity of Bi2WO6 with PVP addition for CO2 reduction into ethanol under visible light

Environmental Science and Pollution Research - The conversion of CO2 into new carbon-based products, such as fuels and chemicals, is an attractive and promising means of mitigating global energy...     

Visible-light-induced photocatalytic reduction of Cr(VI) with coupled Bi2O3/TiO2 photocatalyst and the synergistic bisphenol A oxidation

Coupled Bi₂O₃/TiO₂ photocatalysts were fabricated by sol–gel and hydrothermal methods and characterized using various spectroscopy techniques. Photocatalytic reduction of Cr(VI) in aqueous solution, together with the synergistic effect of photodegradation of bisphenol A (BPA), was investigated using these coupled Bi₂O₃/TiO₂ under visible-light irradiation. Coupling of Bi₂O₃ inhibited the phase transformation from anatase to rutile and extended absorption region to visible light. Bi ions did not enter TiO₂ lattice and were more likely to bond with oxygen atoms to form Bi₂O₃ on the surface of TiO₂. Photovoltage signals in visible range revealed the effective interfacial charge transfer between Bi₂O₃ and TiO₂. Two percent Bi₂O₃/TiO₂ exhibited the highest photocatalytic activity of visible-light-induced reduction of Cr(VI). The addition of BPA effectively increased the photocatalytic reduction of Cr(VI). Simultaneously, the presence of Cr(VI) promoted the degradation of BPA, which was demonstrated by the investigation of TOC removal yield and generated intermediates. A possible mechanism of photocatalytic reduction of Cr(VI) and degradation of BPA in Bi₂O₃/TiO₂ system was proposed. The synergistic effect, observed between reduction of Cr(VI) and degradation of BPA, provides beneficial method for environmental remediation and purification of the complex wastewater.     

Modification of photocatalytic property of BaTiO3 perovskite structure by Fe2O3 nanoparticles for CO2 reduction in gas phase

In this work, perovskite structure of BaTiO₃ was coupled with Fe₂O₃ in different molar ratios achieving the best photocatalytic performance of CO₂ reduction in the presence of CH₄ as reducing agent; both of them are main greenhouse gases. The photocatalysts were synthesized by facile hydrothermal method. The samples were characterized by XRD, FTIR, FESEM, EDX, UV–Vis DRS, and photoluminescence (PL) analyses. The BaTiO₃ synthesized in this research showed a weak PL signal which is due to the intrinsic ferroelectric property as has been observed in previous reports. Compared to the pure BaTiO₃ and Fe₂O₃, the heterojunctions exhibited enhanced photocatalytic activity. The maximum CO₂ reduction under visible light irradiation was obtained to be 22% during 60 min process time. The enhanced photocatalytic activity could be attributed to the increased optical absorption, the good separation, and immigration of photogenerated charge carriers that decreased the recombination rate of charge carriers in the n–n heterojunction.

     

2,4-Dichlorophenoxyacetic acid (2,4-D) photodegradation on WO3-TiO2-SBA-15 nanostructured composite

Environmental Science and Pollution Research - A current environmental problem is the uncontrolled use of various pesticides that are harmful to the environment and public health. The herbicide...     

Catalytic ozonation of 2,4-dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k(obs)) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k(obs) value increased from 19.3 to 26 M(-1) s(-1) and 67 M(-1) s(-1) when varying the alumina dose from 1 to 2 and 4 g L(-1), respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L(-1), the k(obs) values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M(-1) s(-1), respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M(-1) s(-1) were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

Catalytic ozonation of 2,4-Dichlorophenoxyacetic acid using alumina in the presence of a radical scavenger

Using a laboratory-scale mixed reactor, the performance of alumina in degrading 2,4-Dichlorophenoxyacetic acid with ozone in the presence of tert-butyl alcohol radical scavenger was studied. The operating variables investigated were the dose of alumina catalyst and solution pH. Results showed that using ozone and alumina leads to a significant increase in 2,4-D removal in comparison to non-catalytic ozonation and adsorption processes. The observed reaction rate constants (k_obs ) for 2,4-D during ozonation were found to increase linearly with increasing catalyst dose. At pH 5, the k_obs value increased from 19.3 to 26 M^?1 s^?1 and 67 M^?1 s^?1 when varying the alumina dose from 1 to 2 and 4 g L^?1, respectively. As pH was increased, higher reaction rates were observed for both non-catalytic ozonation and catalytic ozonation processes. Thus, at pH 3 and using a catalyst dose of 8 g L^?1, the k_obs values for non-catalytic ozonation and catalytic ozonation processes were 3.4 and 58.9 M^?1 s^?1, respectively, whereas at pH 5 reaction rate constants of 6.5 and 128.5 M^?1 s^?1 were observed, respectively. Analysis of total organic carbon suggested that catalytic ozonation with alumina achieved a considerable level of mineralization of 2,4-D. Adsorption of 2,4-D on alumina was found to play an important role in the catalytic ozonation process.     

The preparation of Zn2+-doped TiO(2) nanoparticles by sol-gel and solid phase reaction methods respectively and their photocatalytic activities

The photocatalytic oxidation of the organic pollutants with TiO(2) as photocatalyst has been widely studied in the world, and many achievements have been made. The degradation of pollutants is highly related to the photocatalytic activity of TiO(2). It is demonstrated that doping ions to TiO(2) is one way to enhance the photocatalytic activity of TiO(2). In this paper, Zn(2+)-doped TiO(2) nanoparticles were prepared through sol-gel and solid phase reaction methods, characterized by means of X-ray diffraction (XRD) and transmission electron microscopy (TEM). The photocatalytic activity of the elaborated powders was studied following the degradation of Rhodamine B. The results showed that the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by sol-gel method is close to that of pure TiO(2) particles, however, the photocatalytic activity of Zn(2+)-doped TiO(2) prepared by solid phase reaction method is much higher than that of pure TiO(2) particles. The most efficient degradation of Rhodamine B was found with TiO(2) particles doped with 0.5% Zn(2+) in mole and calcined at 500 degrees C. Also the reason for the enhancement of the photocatalytic activity of TiO(2) by Zn(2+) doping through solid phase reaction method was discussed.     

Degradation of 2,7-dichlorodibenzo-p-dioxin by Fe(3+)-H(2)O(2) mixed reagent

Fe(3+)-H(2)O(2) mixed reagent, but not Fe(2+)-H(2)O(2), was found to be capable of degrading 2,7-dichlorodibenzo-p-dioxin (DCDD). A reaction mixture of FeCl(3) (8 mM) and H(2)O(2) (1%) caused approximately 50% degradation within 6 h and >90% degradation within 24 h at 27 degrees C. Increasing the temperature remarkably stimulated degradation: at 70 degrees C, approximately 100% degradation was achieved within 15 min. When DCDD-treated model soil (5 micrograms/g) was conducted, approximately 100% of the DCDD was degraded within 30 min at 70 degrees C (both reagents were added every 10 min). These results suggest that Fe(3+)-H(2)O(2) mixed reagent may be a new tool for combating persistent environmental pollutants such as dioxins and polychlorinated biphenyls.     

Simultaneous photocatalytic reduction of Cr(VI) and oxidation of phenol over monoclinic BiVO4 under visible light irradiation

BiVO4 powder with monoclinic structure was prepared and used as a visible-light catalyst simultaneously for the photooxidation of phenol and the photoreduction of Cr(VI). The photocatalytic efficiency was found to be rather low for either single phenol solution or single Cr(VI) solution. However, the photocatalytic reduction of Cr(VI) and photocatalytic oxidation of phenol proceed more rapidly for the coexistence system of phenol and Cr(VI) than for the single process, showing synergetic effect between the oxidation and reduction reactions. For the simultaneous photocatalytic reduction-oxidation process, the first-order kinetic constant of phenol degradation was 0.0314 min-1, being about six times higher than that for the photocatalytic process of single phenol. This result reveals the feasibility of using Cr(VI) as the electron scavenger of mBiVO4-mediated photocatalytic process of phenol degradation, and gives us an enlightenment to employ other semiconductor with a better visible light response but with a more positive band edge to efficiently degrade organic pollutants. This is the first report for simultaneous photocatalytic reduction of Cr(VI) and removal of phenol under visible light irradiation using photocatalyst mBiVO4.     

钙镁离子及重碳酸盐对零价铁还原对氯硝基苯的影响

通过间歇式实验,考察了地下水中常见硬度离子Ca2＋、Mg2＋及HCO3-的独立作用和联合作用对零价铁还原对氯硝基苯的影响。实验结果表明,Ca2＋、Mg2＋对零价铁还原对氯硝基苯反应的促进作用不明显。HCO3-浓度为0～100mg/L时可显著提高零价铁还原对氯硝基苯的速率,反应2 h后对氯硝基苯转化率由44.1%升至84...     

Reduction of ferrate(VI) and oxidation of cyanate in a Fe(VI)-TiO2-UV-NCO- system

The aqueous photocatalytic degradation of cyanate (NCO(-)), which is a long-lived neurotoxin formed during the remediation of cyanide in industrial waste streams, was studied in the ferrate(VI)-UV-TiO2-NCO(-) system. Kinetics measurements of the photocatalytic reduction of ferrate(VI) were carried out as a function of [NCO(-)], [ferrate(VI)], [O(2)], light intensity (I(o)), and amount of TiO2 in suspensions at pH 9.0. The photocatalytic reduction rate of ferrate(VI) in the studied system can be expressed as -d[Fe(VI)]/dt=kI(o)(0.5) [NCO(-)] [TiO2]. The rate of photocatalytic oxidation of cyanate with ferrate(VI) was greater than the rate in the analogous system without ferrate(VI). The possibility of involvement of reactive ferrate(V) species for this enhancement was determined by studying the reactivity of ferrate(V) with NCO(-) in a homogeneous solution using a premix pulse radiolysis technique. The rate constant for the reaction of ferrate(V) and NCO(-) in alkaline medium was estimated to be (9.60+/-0.07) x 10(2) M(-1) s(-1), which is much slower than the ferrate(VI) self-decomposition reaction (k approximately 10(7) M(-1) s(-1)). An analysis of the kinetic data in the Fe(VI)-UV-TiO2-NCO(-) system suggests that ferrate(V) is not directly participating in the oxidation of cyanate. Possible reactions in the system are presented to explain results of ferrate(VI) reduction and oxidation of cyanate.     

Co-exposure of Bi2O3 nanoparticles and bezo[a]pyrene-enhanced in vitro cytotoxicity of mouse spermatogonia cells

Environmental Science and Pollution Research - Recent attention has been focused on reproductive toxicity of nanoscale materials in combination with pre-existing environmental pollutants. Due to...     

Effects of acid treatments of activated carbon on its physiochemical structure as a support for copper oxide in DeSO(2) reaction catalysts

To enhance the dispersion of active sites, modification of the AC supports with different acid solution might result in various surface oxygen groups which act as anchoring sites for metallic precursor to stay and improve the reactivity between AC supports and copper precursor. In the present work, the AC support is tailored with HCl and HNO(3), respectively. The pore structure, surface oxygen groups of the AC support and catalysts as well as catalyst dispersion before and after acid treatments are systematically studied by BET, pH(slurry), TPD, and XRPD analyses. It is found that the order of activity in DeSO(2) reaction is as follows: Cu/AC-HCl>Cu/AC>Cu/AC-HNO(3). The same sequence is also observed for the pore structure of AC supports, the catalyst dispersion, but not for the amounts of CO(2) evolving during TPD experiments of supports. The key role of acid treatment on carbon surface chemistry and pore structure, which are closely related to catalyst dispersion and adsorption capacity, is examined to rationalize these findings. Furthermore, under the NO/NH(3)=1 the NO could be selective catalytic reduction with NH(3) in the presence of O(2), which catalyzed by fresh and spent AC-supported catalyst.     

The separation of catalyst after photocatalytic reactions conducted in the presence of TiO2/FeCl3/UV

One of the problems connected with wastewater treatment by the photocatalytic method in the presence of TiO2 suspension is necessity of the later catalyst separation. The method proposed by us for this purpose, consists in the usage of coagulation of TiO2 suspension with the aid of FeCl3, particularly in the cases when addition of the salt is used in order to intensification of the photocatalytic process. The effects of the TiO2 separation were studied from the mixtures, after photocatalytic Acid Orange 7 degradation, with dosage of FeCl3 at different stages of the process. The coagulation was carried out at different pH values as well as different FeCl3 concentrations. It was stated that nearly 100% of separation and simultaneously, nearly 100% of decolouration of the examined Acid Orange 7 solutions after their illumination in the presence of TiO2/FeCl3 and coagulation which was produced only by increasing of pH of the obtained mixtures, were nearly possible.     

Enhanced growth and reproduction of Caenorhabditis elegans (Nematoda) in the presence of 4-nonylphenol

The nematode Caenorhabditis elegans was exposed over a whole fife-cycle (72 h) to several concentrations of 4-nonylphenol (NP; nominal concentrations: 0-350 microg/l). Growth and reproduction of C. elegans were enhanced at NP concentrations of 66 and 40 microg/l, respectively, with effects showing dose-response relationships. These stimulatory effects might be of ecological relevance in benthic habitats, where organisms can be exposed to high concentrations of NP.     

Enhanced deodorization and sludge reduction in situ by a humus soil cooperated anaerobic/anoxic/oxic (A2O) wastewater treatment system

Simultaneous sludge reduction and malodor abatement in humus soil cooperated an anaerobic/anoxic/oxic (A2O) wastewater treatment were investigated in this study. The HSR-A2O was composed of a humus soil reactor (HSR) and a conventional A2O (designated as C-A2O).The results showed that adding HSR did not deteriorate the chemical oxygen demand (COD) removal, while total phosphorus (TP) removal efficiency in HSR-A2O was improved by 18 % in comparison with that in the C-A2O. Both processes had good performance on total nitrogen (TN) removal, and there was no significant difference between them (76.8 and 77.1 %, respectively). However, NH₄ ⁺–N and NO₃ ^?–N were reduced to 0.3 and 6.7 mg/L in HSR-A2O compared to 1.5 and 4.5 mg/L. Moreover, adding HSR induced the sludge reduction, and the sludge production rate was lower than that in the C-A2O. The observed sludge yield was estimated to be 0.32 kg MLSS/day in HSR-A2O, which represent a 33.5 % reduction compared to a C-A2O process. Activated sludge underwent humification and produced more humic acid in HSR-A2O, which is beneficial to sludge reduction. Odor abatement was achieved in HSR-A2O, ammonium (NH₃), and sulfuretted hydrogen (H₂S) emission decreased from 1.34 and 1.33 to 0.06 mg/m³, 0.025 mg/m³ in anaerobic area, with the corresponding reduction efficiency of 95.5 and 98.1 %. Microbial community analysis revealed that the relevant microorganism enrichment explained the reduction effect of humus soil on NH₃ and H₂S emission. The whole study demonstrated that humus soil enhanced odor abatement and sludge reduction in situ.     

The enhanced PC and PEC oxidation of formic acid in aqueous solution using a Cu-TiO2/ITO film

The photocatalytic (PC) and photoelectrocatalytic (PEC) activity of Cu-TiO2/ITO films for degrading formic acid in aqueous solution was investigated in this study. Compared with a TiO2/ITO film, the degradation efficiency of formic acid on the Cu-TiO2 films increased markedly in both the PC and PEC oxidation processes. However, it was found that the photodeposited Cu metal on the Cu-TiO2 films could electrochemically dissolute during the PEC reaction, while an electrical bias with the voltage higher than 1.48 V was applied. It is believed this is a common problem occurred for several metals deposition on the TiO2 films, which results in a poor stability of the metal-deposited TiO2 electrode in PEC processes. To improve the stability of the Cu-TiO2 electrode, an alternative process between PC and PEC reactions was investigated. It was found that the dissolute Cu metal during the PEC process was re-deposited on the Cu-TiO2 film again during the PC process. The experiments with repeated runs demonstrated that this alternative process could not only overcome the loss of Cu, but also enhance the PEC oxidation efficiency of the Cu-TiO2 films.     

Toxicity of lead on Ceriodaphnia dubia in the presence of nano-CeO(2) and nano-TiO(2)

Although engineered nanoparticles (NPs) could negatively impact environmental organisms, the synergistic effect of NPs and other toxic substances, which could be more significant than that of NP alone, have seldom been examined. The effect of two common NPs, nano-CeO₂ and nano-TiO₂, on the toxicity of Pb was evaluated using Ceriodaphnia dubia (C. dubia) as the model organism. Standard EPA procedures were followed in the toxicity evaluation. The toxicity of bare NPs (without Pb) was first evaluated and safe doses (levels without causing lethal effect) of NPs were used in the synergistic studies. It was found that the overall toxicity of Pb in the system containing NPs was greater than that of Pb alone, as indicted by the reduced median lethal concentration (LC₅₀) of soluble Pb. The sorption of Pb onto the NP, and the uptake of NPs in the gastrointestinal tract of C. dubia were validated. Therefore, the uptake of Pb-loaded NPs increased the exposure of C. dubia to Pb, resulting in the enhanced toxicity. Reducing the solution pH could shift Pb speciation and enhance the overall toxicity of Pb, with or without the presence of NPs.