Polyols and Rigid Polyurethane Foams from Cashew Nut Shell Liquid

Cashew nut shell liquid (CNSL) is a natural aromatic oil consisting of a mixture of phenolic structures with a carboxyl group in ortho position and substituted in meta position with a hydrocarbon chain of 15 carbon atoms. The major component of CNSL is anacardic acid (90?%), which is easily decarboxylated to cardanol by distillation. The present work describes the synthesis of new biobased Mannich polyols for rigid polyurethane foams in two steps: synthesis of Mannich bases by reacting phenolic ring of cardanol with N-(2-hydroxyethyl)-1,3-oxazolidine followed by alkoxylation reactions. The polyols were characterized by wet methods (hydroxyl numbers, viscosity, acid value, density, water content, iodine value etc.), spectroscopic methods (FT-IR, ¹H NMR and ¹³C NMR) and by Gel Permeation Chromatography. The Mannich polyols from cardanol are excellent replacements for petrochemical derived Mannich polyols based on nonyl phenol. Cardanol-based polyols were used successfully for the preparation of rigid polyurethane foams of good physical?Cmechanical and fireproofing properties.     

Aliphatic–Aromatic Polyols by Thiol–Ene Reactions

Aliphatic–aromatic polyols were synthesized by thiol–ene reactions (photochemical or thermal) using mercaptanized starting materials from bio-based compounds: limonene dimercaptan, thioglycerol, mercaptanized castor oil and isosorbide (3-mercaptopropyl) ether. Aromatic starting materials were phenols containing double bonds; ortho-allyl phenol (OAP, petrochemical-based) and eugenol (EUG, bio-based). The phenolic hydroxyl groups were blocked by alkoxylation with propylene oxide (PO) or glycidol (GLY) prior to use in thiol–ene reaction. The aromatic rings were attached to the mercaptans by reacting thiol groups with the double bonds of alkoxylated OAP (OAP–PO and OAP–GLY) and alkoxylated EUG (EUG–PO and EUG–GLY). These synthesized aliphatic–aromatic polyols were utilized for preparation of rigid polyurethane foams whose physical–mechanical properties were superior to those made only from bio-based aliphatic polyols. These rigid PU foams can be used in a wide range of applications; such as thermal insulation of freezers, buildings, pipes and storage tanks for food and chemical industries, as wood substitute, packaging materials and flotation materials.     

Novel Renewable Polyols Based on Limonene for Rigid Polyurethane Foams

Novel renewable polyols based on limonene were synthesized using thiol-ene “click” chemistry. These limonene based polyols were structurally characterized using wet methods (hydroxyl number, acid value and viscosity), gel permeation chromatography and spectroscopic methods. The results indicated that high yield of polyols from limonene based materials can be obtained using thiol-ene reaction. These limonene based polyols were used successfully for preparation of rigid polyurethane foams. These foams had regular shape cells and uniform cell size distribution. Thermal studies on these foams indicated that foams were thermally stable up to 250 °C. The glass transition temperature of the foams was higher than 200 °C. These rigid polyurethane foams had high compressive strength and the highest compressive strength of 195 kPa was observed. These foams have good physical–mechanical characteristics and could be suitable for all the applications of rigid polyurethane foams such as thermal insulation of freezers, storage tanks for the chemical and food industries, and packing materials for food industries.     

One-Pot Reaction of Waste PET to Flame Retardant Polyurethane Foam,via Deep Eutectic Solvents-Based Conversion Technology

Depolymerization of polyethylene terephthalate (PET) is a promising technology for producing recycled monomers. Using a deep eutectic solvent (DES)-based catalyst, the PET glycolysis process produces bis-(2-hydroxyethylene terephthalate) (BHET). This recycled monomer reacts with isocyanate and forms polyurethane foam (PUF). The DES-based one-pot reaction is advantageous because it is a low-energy process that requires relatively lower temperatures and reduced reaction times. In this study, choline chloride/urea, zinc chloride/urea, and zinc acetate/urea based DESs were adopted as DES catalysts for glycolysis. Subsequently, the conversion of PET, BHET yield, and OH values were evaluated. Both filtered and unfiltered reaction mixtures were used as polyols for PUF polymerization after characterization of the acid and hydroxyl values of the polyols, as well as the NCO (–N=C=O) value of isocyanate. In the case of unfiltered reaction mixtures, PUF was obtained via a one-pot reaction, which exhibited higher thermal stability than PUF made from the filtered polyols. This outcome indicated that oligomeric BHET containing many aromatic moieties in unfiltered polyols contributes to the thermal stability of PUF. This environmentally friendly and relatively simple process is an economical approach for upcycling waste PET.

     

Scaled-up and economic assessment approach of the split-phase glycolysis process for the recycling of flexible polyurethane foam wastes

The economic viability of the split-phase glycolysis process for the recycling of any kind of flexible polyurethane foam waste employing crude glycerol as cleavage agent has been demonstrated. First, experiments at pilot plant scale were carried out to check that the process can be extrapolated to larger scales. With the goal of scaling-up the process from laboratory scale to pilot plant, geometric similarity criteria were applied together with dynamic similarity for laminar flow in agitated tank reactors. Hence, a pilot plant installation was designed with geometrically similar equipment to those used for lab scale, obtaining analogous results in terms of recovered polyol properties. Then, the basic design of a split-phase glycolysis industrial plant with a capacity for treating 270 Tm per year of flexible PU foams scraps was proposed. Finally, the economic feasibility of such recycling process was confirmed because of the obtention of a Net Present Value (NPV) of 1,464,555€, with an Internal Rate of Return (IRR) of 27.99%, and a payback time between 4 and 5 years.

     

Synthesis and Characterization of Low Volatile Content Polyurethane Dispersion from Depolymerised Polyethylene Terphthalate

In the past few decades, governments and international agencies have been placing more emphasis on the improvement of production technique, working conditions and reduction of the toxic emission to the atmosphere. In this context aqueous polyurethane dispersion was synthesized from depolymerised polyethylene terphthalate (PET) waste. 1,4-Butanediol was used in PET depolymerisation. Polyurethane dispersion films were characterized using differential scanning calorimeter, Fourier transform infrared spectroscopy, gel permeable chromatography, etc. Incorporation of PET waste in polyurethane dispersion was an added advantage in waste management and produced better quality polyurethane dispersion.     

Aminolysis and aminoglycolysis of waste poly(ethylene terephthalate)

This paper describes the chemical degradation of waste poly(ethylene terephthalate) (PET) with polyamines or triethanolamine, the characteristics of the products, and a search for ways to use these products. Solvolysis of the polymer ester bonds was caused by diethylenetriamine, triethylenetetramine, and their mixtures, as well as mixtures of triethylenetetramine and p-phenylenediamine or triethanolamine. Products of aminolysis or aminoglycolysis of PET obtained in reactions performed at 200–210°C (with a molar ratio of the recurrent polymer unit to amine of 1 : 2) have been characterized using nuclear magnetic resonance (NMR). Viscosity and hydroxyl number measurements have been done for PET/triethanolamine products. Substances from aminolytical reactions with polyamines were tested as hardeners for liquid epoxy resins, and the product of polymer aminoglycolysis with triethanolamine was tested as an epoxy resin hardener, e.g., for water-borne paints, and a polyol component for rigid polyurethane foams. The compositions of epoxy resin hardeners have been characterized using DSC and rheometry. Comparative analyses of the hardened epoxy materials have been done on the basis of glass temperature and mechanical properties data, as well as some specific properties of the coating materials and rigid polyurethane foams. Received: September 15, 2000 / Accepted: September 21, 2000     

Effects of Wood Fiber and Microclay on the Performance of Soy Based Polyurethane Foams

Various polyurethane (PU) foams were prepared by in situ reaction of isocyanate and soy-based polyol. The effects of wood fiber and microclay on the foam morphologies, mechanical properties and thermal behaviors of PU foams were investigated. NCO index had fundamental impacts on the influences of wood fiber and microclay on the performance of PU foams. The reinforcement behavior of flexible foams was different to that of both semi-rigid and rigid foams. Both fiber and microclay improved the compressive strength at a high NCO index of 140–250, and contributed to relative high decomposition temperatures. Unlike the compressive strength, the tensile strength was decreased due to the amount of hard polyurea formation from secondary reactions at the highest NCO level. In addition, wood fiber had different reinforcement mechanism from microclay. Wood fiber desired to form chemical bonds during foaming while microclay had potential to form physical insertions. This difference was expressed by the change of their thermal degradation temperature.     

Novel polyol initiator from polyurethane recycling residue

Flexible polyurethane foams can be advantageously treated by two-phase glycolysis in order to recover polyols with improved quality. The bottom phase obtained, which contains highly toxic reaction by-products and the excess glycol, presents an environmental and economic problem which should be solved. The main purpose of this work is the development of process for the valorization of these by-products, converting them in non-dangerous and profitable substances. For this process, most of the glycol can be recovered by means of vacuum distillation in order to reuse it in the glycolysis. On the other hand, the vacuum residue, containing the isocyanate part of the glycolysis by-products, was assayed as initiator in the synthesis of new polyols. Propoxylation of the initiator was carried out in different experimental conditions to obtain several polyether-polyols. Rigid polyurethane foams with suitable technical properties were synthesized with those polyols synthesized with the dangerous glycolysis by-products.     

Structure,Mechanical, Thermal and Fire Behavior Assessments of Environmentally Friendly Crude Glycerol-Based Rigid Polyisocyanurate Foams

In this work, rigid polyisocyanurate foams were prepared at partial substitution (0–70 wt%) of commercially available petrochemical polyol, with previously synthesized biopolyol based on crude glycerol and castor oil. Influence of the biopolyol content on morphology, chemical structure, static and dynamic mechanical properties, thermal insulation properties, thermal stability and flammability was investigated. Incorporation of 35 wt% of crude glycerol-based polyol had reduced average cell size by more than 30% and slightly increased closed cell content, simultaneously reducing thermal conductivity coefficient of foam by 12% and inhibiting their thermal aging. Applied modifications showed also positive impact on the mechanical performance of rigid foams. Increase of crosslink density resulted in enhancement of compressive strength by more than 100%. Incorporation of prepared biopolyol resulted in enhancement of thermal stability and changes in degradation pathway. Up to 35 wt% share of crude glycerol-based polyol, foams showed similar flammability as reference sample, which can be considered very beneficial from the environmental point of view.     

Biobased Polyurethanes from Rapeseed Oil Polyols: Structure, Mechanical and Thermal Properties

Biobased polyols were synthesized from rapeseed oil (RO) with diethanolamine (DEA), triethanolamine (TEA) and glycerol (GL) at different molar ratios. The structures of the synthesized polyols were analyzed using FTIR-ATR spectroscopy. Polyurethane (PU) networks from RO/DEA polyols and polymeric MDI showed higher tensile strength, modulus and hardness, but their elongation at break decreased, compared to the case of the PU obtained from RO/TEA and RO/GL polyols. The tensile strength and modulus of PU networks increased with increasing PU cohesion energy density (CED) and decreasing molecular weight between crosslinks M _c . From the thermogravimetric analysis and its derivative thermograms, at the first stage of destruction (below 5 % weight loss) in the air and inert atmosphere, the PU obtained from RO polyols were ranked in the following order: PU RO/GL > PU RO/TEA > PU RO/DEA, and their thermostability was higher than that of the PU based on propylene oxide.     

One-Component Spray Polyurethane Foam from Liquefied Pinewood Polyols: Pursuing Eco-Friendly Materials

The use of petroleum-derived products should be avoided regarding the principles of green and sustainable chemistry. The work reported herein, is aimed at the liquefaction of pine shavings for the production of an environmentally-friendly polyol suitable to be used in the formulations of sprayable polyurethane foams. The biopolyols were obtained in high yield and were used to replace those derived from fossil sources, to produce more “greener” polyurethane foams and therefore, less dependent on petroleum sources, since the polyol component was substituted by products resulting from biomass liquefaction. The partial and fully exchange of the polyols was accomplished, and the results compared with a reference foam. The foams were afterward, chemical, physical, morphological, and mechanically characterized. The complete replacement of polyether polyol and polyol polyester has presented some similar characteristics as that used as a reference, validating that the path chosen for the development of more sustainable materials is on the right track for the contribution to a cleaner world.     

Biocompatible Polyurethane Scaffolds Prepared from Glycerol Monostearate-Derived Polyester Polyol

Biodegradable polyester polyol was synthesized from oleochemical glycerol monostearate (GMS) and glutaric acid under a non-catalyzed and solvent-free polycondensation method. The chemical structure of GMS-derived polyester polyol (GPP) was elucidated by FTIR, ¹H and ¹³C NMR, and molecular weight of GPP was characterized by GPC. The synthesized GPP with acid value of 3.03 mg KOH/g sample, hydroxyl value of 115.72 mg KOH/g sample and M_n of 1345 g/mol was incorporated with polyethylene glycol (PEG) and polycaprolactone diol (PCL diol) to produce a water-blown porous polyurethane system via one-shot foaming method. The polyurethanes were optimized by evaluating glycerol as a crosslinker, silicone surfactant and water blowing agent on tensile properties of polyurethanes. All polyurethanes underwent structural change, and crystalline hard segments of polyurethanes were shifted to higher temperature suggested that hard segments undergone re-ordering process during enzymatic treatment. In terms of biocompatibility, polyurethane scaffold produced by reacting 100% w/w of GPP with isophorone diisocyanate and additives showed the highest cells viability of 3T3 mouse fibroblast (94%, day 1), and MG63 human osteosarcoma (107%, day 1) and better cell adhesion as compared to reference polyurethane produced by only PEG and PCL diol (3T3 cell viability: 8%; MG63 cell viability: 2%). The current work demonstrated GPP synthesized from renewable and environmental friendly resources produced polyurethanes that allows improvement in physico-chemical, mechanical and biocompatibility properties. By blending with increasing content of GPP, the water-blown porous polyurethane scaffold has shown great potential as biomaterial for soft and hard tissue engineering.     

Polyacetal Polyols for Polyurethanes

The synthesis of telechelic polyacetals with terminal hydroxyl groups (polyacetal polyols), by the reaction of triethylene glycol divinyl ether with dipropylene glycol in the presence of trimethylolpropane or other triols or diols as starters, in acidic catalysis, has been studied. The synthesized liquid polyacetal triols and polyacetal diols were characterized by hydroxyl number, viscosity, acidity, number average molecular weight (M_n), weight average molecular weight (M_w), molecular weight distribution (M_w/M_n), FT-IR spectra. The obtained polyacetals were transformed in cast elastomers by the reaction with the isocyanate Mondur CD (modified diphenyl methane diisocyanate) with properties very close to the elastic polyurethanes obtained by using conventional polyether triols, copolymers propylene oxide–ethylene oxide. The polyacetal polyols are suitable for the synthesis of elastic polyurethanes (polyurethane elastomers, flexible polyurethane foams). Polyacetals are well known biodegradable polymers. Therefore, the polyurethanes based on polyacetal polyols are expected to be biodegradable.     

Alkyd-amino resins based on waste PET for coating applications

Waste polyethylene terephthalate (PET) flakes were depolymerized by using propylene glycol (PG) in the presence of zinc acetate as catalyst. Glycolysis reaction products of waste PET obtained by using PET/glycol molar ratio 1/2. Two short oil alkyd resins of high acid values (30-40mgKOH/g) were prepared from phthalic anhydride (PA), glycerin (G), coconut oil fatty acids (COFA) and glycolyzed products of waste PET (PET-based alkyd resins) or glycols (PG) (reference alkyd resins). These alkyd resins were blended with 30%, 40%, and 50% of a commercial urea-formaldehyde, melamine-formaldehyde and urea-formaldehyde/melamine-formaldehyde mixture (1/1 weight ratio) and heated at 140 degrees C. The physical and chemical properties such as drying time, hardness, abrasion resistance, adhesion strength, water resistance, alkaline resistance, acid resistance, gelation time, and thermal oxidative degradation resistance (with thermogravimetric analysis, TGA) of these alkyd-amino resins were investigated. The properties of the waste PET-based resins were found to be compatible with the properties of the reference resins.     

Development of Lignin and Nanocellulose Enhanced Bio PU Foams for Automotive Parts

The green rigid polyurethane (PU) foam has been developed with 100 % soy polyol after optimization of formulation ingredients and lignin has been introduced and isocyanate content reduced in the green rigid PU foam. The cellulosic nanofibers have also been successfully incorporated and dispersed in green rigid PU foam to improve the rigidity. The influence of nano cellulose fiber modification (enzymatic treatment, hydrophobic modification with latex) on the foam density, open cell content, foam raise height, water vapor, and mechanical properties of rigid PU foam were studied. The foamed structures were examined using scanning electron microscopy to determine the cell size and shape due to the addition of cellulosic nanofibers. The odor test were performed to evaluate the odor concentration 100 % soyol based PU foam including lignin and nanofiber and compared to 100 % synthetic based polyol PU foam. The experimental results indicated that the compression and impact properties improved due to the modification of nano cellulosic fibers. The odor concentration level of nanofiber reinforced rigid PU foam reduced significantly compared to 100 % PU foam due to the replacing of isocyanate content. It can be said that with an appropriate combination of replacing isocyanate by lignin and addition of nanofiber, rigid PU foam properties could be improved.     

Environmentally Friendly Polyurethane Composites: Preparation, Characterization and Mechanical Properties

The waterborne polyurethane (PU) prepolymer was prepared based on isophorone diisocyanate (IPDI), polyester polyol (N220), dimethylol propionic acid (DMPA) and hydroxyethyl methyl acrylate (HEMA). The modified waterborne polyurethane–acrylate (PUA) emulsions were obtained with different proportions of acrylate (butyl acrylate and methyl methacrylate) and initiating agent by in situ dispersion technique. The structures and thermal properties of prepared PU and PUA were analyzed and characterized with FT-IR, UV–Vis spectroscopy and DSC. The PUA hybrid samples had lower glass transition temperature of hard segment and higher decomposition temperatures than PU sample. Performances of the emulsion and film were studied by means of apparent viscidity, particle size and polydispersity, surface tension and mechanical properties. The results indicated that the particle sizes of the PUA dispersions were larger than those of the pure PU and the solvent resistance, mechanical properties of PUA films was improved compare with the unmodified polyurethane film. The film had the biggest hardness and the least water absorption when the BA/MMA mass ratio 5:5 modified PU. The obtained PUA have great potential application such as coatings, leather finishing, adhesives, sealants, plastic coatings and wood finishes.     

Water-Blown Castor Oil-Based Polyurethane Foams with Soy Protein as a Reactive Reinforcing Filler

To decrease the usage of petroleum based materials, a kind of bio-resource based composite foams were developed with soy protein isolate (SPI) as reactive reinforcing filler in castor oil based polyurethane foams (PUF) prepared by self-rising method using water as a blowing agent. The resulting composite foams were evaluated for their morphology, density, mechanical and biodegradation properties, etc. Fourier transform infrared spectroscopy study exhibited characteristic peaks for SPI and PUF and indicated that the amino groups and hydroxyl groups on SPI reacted with polyphenyl polymethylene polyisocyanates (PAPI) to increase the crosslinking degrees of the composite foams. Densities of the resultant composites were found to increase with increasing SPI content. Mechanical properties of the samples were improved with the increase of SPI content. The compost tests further proved that the composite PUF had better biodegradability than neat PUF. Therefore, this research has provided a simple method of preparing the bio-resource based polyurethane foams, while exploring the potential of using SPI in polyurethane foam applications.     

Influence of Palm Oil-Based Polyol on the Properties of Flexible Polyurethane Foams

This paper describes the effect of the modification of polyurethane system with palm oil-based polyol on the cell structure and physical?Cmechanical properties of polyurethane foams. Flexible polyurethane foams were prepared by substituting a part of petrochemical polyether-polyol with the palm oil polyol. Selected physical?Cmechanical properties of these foams were examined and compared to the properties of reference foam. The properties such as apparent density, tensile strength, elongation at break, resilience, compressive stress and thermal stability were analyzed. It was found that the modifications of polyurethane formulation with palm oil polyol allow to improve selected properties of final products.     

Recent Contributions to the Preparation of Polymers Derived from Renewable Resources

The aim of this paper is to provide an update on the ongoing research of our laboratory in the field of polymeric materials derived from biomass components. The first section deals with the oxypropylation of different vegetable or animal biomass residues and the use of the ensuing polyols in different polyurethane formulations. Thus, foams, elastomers, and membranes were obtained and their properties compared favorably with those of equivalent materials prepared from petroleum-based sources. The second section is devoted to furan copolymers and their use in reversibly crosslinked elastomers via the Diels–Alder reaction and in the field of photosensitive materials. The third section describes novel approaches to the surface modification of cellulosic fibers to be employed in composite materials with polymeric matrices, consisting in the use of organometallics and siloxanes as coupling agents. The final two sections are devoted to a brief outline of the role of lignins and vegetable oils as additives in printing inks, varnishes, and paints.