Comparison of zinc complexation properties of dissolved natural organic matter from different surface waters

The zinc binding characteristics of natural organic matter (NOM) from several representative surface waters were studied and compared. NOM samples were concentrated by reverse osmosis. The samples were treated in the laboratory to remove trace metals. Square wave anodic stripping voltammetry (SWASV) was used to study zinc complexing properties of those NOM samples at fixed pH, ionic strength, and dissolved organic carbon (DOC) concentrations. Experimental data were compared to the predictions from the Windermere Humic Aqueous Model (WHAM) Version VI. At the same pH, ionic strength, and temperature, the zinc titration curves for NOM samples from different surface water sources tested in our study almost overlapped each other, indicating similarity in zinc binding properties of the NOM. A discrete two-site model gave good fits to our experimental titration data. Non-linear fitting by FITEQL 4.0 shows that the conditional zinc binding constants at the same pH are similar for NOM from different sources, indicating that zinc complexation characteristics of the NOM used in our study do not depend on their origin and one set of binding parameters can be used to represent Zn-NOM complexation for NOM samples from those different surface water sources representing geographically diverse locations. In addition, the total ligand concentrations (L(1,T), L(2,T), and L(T)) of all NOM show no observable gradation with increasing pH (L(1,T)=2.06+/-0.80 mmol/g carbon; L(2,T)=0.12+/-0.04 mmol/g carbon; L(T)=2.18+/-0.78 mmol/g carbon), while the conditional binding constants of zinc by NOM (logK(ZnL)(c)) show a linear increase with increasing pH(logK(1)(c)(pH=6.0)=4.69+/-0.25; logK(1)(c)(pH=7.0)=4.94+/-0.10; logK(1)(c)(pH=8.0)=5.25+/-0.006; logK(2)(c)(pH=6.0)=6.29+/-0.13; logK(2)(c)(pH=7.0)=6.55+/-0.08; logK(2)(c)(pH=8.0)=6.86+/-0.023) with a slope of ca. 0.28, indicating the zinc-NOM complexes become more stable at higher pH. The WHAM VI predicted free zinc ion activities at high zinc concentrations agree with our experimental results at pH 6.0, 7.0, and 8.0. However, the zinc binding of these NOM samples is over estimated by WHAM VI at zinc concentrations below 10(-6) M at pH 8.0.     

Rhamnolipid morphology and phenanthrene solubility at different pH values

The effect of pH and rhamnolipids on the solubility of phenanthrene was investigated in a sand-water system. Batch phenanthrene solubilization experiments in this system showed that the highest phenanthrene solubility occurred at pH 5 in the presence of 240 and 150 mg L(-1) rhamnolipids. As the pH was increased from 5 to 7, the apparent solubility of phenanthrene decreased and then stabilized from pH 7 to 8. At pH 4, a dramatic decrease in phenanthrene solubility was observed. This result is in contrast to previous findings obtained in an aqueous system without soil particles. To investigate the reason for this decrease, the critical micelle concentrations (CMCs) were measured in the presence or absence of sand particles, and the maximum amount of sorbed biosurfactant at each pH was calculated based on the differences of the two CMC values. More rhamnolipid molecules were lost by the sorption into sand particles at pH 4 than at other pH values; this explains the dramatic decrease of solubility at pH 4 in the sand-water system. To confirm the explanation for the different solubilizing capacity that results from the structural change of biosurfactant aggregate, cryo-transmission electron microscopy was used. Micrographs showed that the rhamnolipid morphology changed from large lamellar sheets, to vesicle, and then to micelle as the pH increased. The large and multilamellar vesicles at pH 5 were considered to be the most effective structure for the solubilization of phenanthrene.     

Formation of pi-pi complexes between phenanthrene and model pi-acceptor humic subunits

Pi-pi interactions may play a role in association of aromatic compounds with natural organic substances. Complexation in aqueous solvents was studied between the pi donor, phenanthrene (PHEN), and model pi-acceptor species (quinones and N-heteroaromatic cations) that represent certain functional units of humic substances. Charge-transfer bands in the UV and ring-current shifts in the proton nuclear magnetic resonance (NMR) spectrum confirmed the face-to-face, pi-pi donor-acceptor nature of the bond. Complexation constants were obtained by the solubility enhancement method; solubility enhancements up to 2500 were found. Ruled out as predominant causes of solubility enhancement were monomer desolvation (i.e., "hydrophobic" effects), partitioning into micelles, pi-cation interactions, and pi-hydrogen bonding. Acceptor self-stacking and formation of higher-stoichiometry acceptor-donor complexes had to be considered in evaluating donor-acceptor equilibria in some cases. The affinity of acceptor for PHEN followed the order of increasing pi-acceptor strength and varied strongly with the degree of ring overlap with PHEN. Complexation between PHEN and the free solution faces of an acceptor was less favorable than intercalation of PHEN between two acceptor units in a stack. A positive hydrophobic effect on complexation was evident in water mixtures with acetone or methanol and found to correlate with the number of faces of PHEN requiring desolvation to form the complex. When hydrophobic effects are subtracted out, the pi-pi complex actually becomes favored as the solvent water content and polarity decline. The results suggest that phenanthrene, and by implication other donor aromatic compounds, are capable of forming pi-pi interactions with appropriate humic fragments.     

Effects of pH and cyclodextrins on pentachlorophenol degradation (mineralization) by white-rot fungi

White-rot fungi (WRF) such as Trametes hirsuta completely degrade (mineralize) pentachlorophenol (PCP) and many other organopollutants. This has led to them being used to decontaminate various substrates (e.g. soil) through biorememediation. However, because PCP is a biocide, it can inhibit fungal growth and thereby its own degradation. It was hypothesized that substrate pH might affect PCP degradation, because when the pH is lower than 4.7 (the pKa for PCP) the phenol predominates, while at higher pH the phenate does. These two PCP species differ markedly in physical and biological properties. The effect of cyclodextrins was also investigated since it is known that the inclusion complexes these form with PCP differ in bioavailability and toxicity from non-complexed PCP. Tests were first made in liquid and agar media (where conditions are relatively easy to control), and then in a sawdust, because it is a common target matrix for WRF bioremediation. Results with the liquid and agar media showed that growth in the presence of inhibitory PCP concentrations decreased as the pH decreased, consistent with the phenol being more toxic. Growth in sawdust was less affected by PCP regardless of the pH, presumably because the PCP sorbed to the wood which decreased its bioavailability. Some cyclodextrins markedly decreased the PCP's toxicity in liquid, agar and sawdust media. Rates of PCP mineralization (measured from production of (14)CO(2) from (14)C PCP) in liquid cultures containing 0.5 mgkg(-1) PCP (a sub-inhibitory concentration) were similar from pH 2.5-7.5, indicating that the phenol and the phenate were equally degradable. Degradation of a growth inhibiting concentration on sawdust (1,000 mgkg(-1)) could be increased slightly by lowering the pH below the pKa, this increasing sorption to the wood. Degradation increased more when the pH was raised well above the pKa, presumably due to the phenate being less toxic and more soluble, making it more available to the degradative system. Although some cyclodextrins decreased growth inhibition, they also interfered with degradation. If this interference could be overcome, cyclodextrins could be used to increase the maximal PCP concentration that could be treated by WRF bioremediation.     

地面水中的非离子氨及其数学计算法

非离子氨的换算工作在我国才刚开始,由于存在不少问题,给标准执行中带来一定困难。本文从水化学实际出发,根据化学平衡原理,导出了水体中非离子氨分布系数(或百分率)的计算公式及其浓度的换算公式。既引入了水温,pH,还引入了离子强度,且介绍了两个水中离子强度的经验计算公式,使计算手续大为简化。本文提出的计算公式,不仅能满足淡水水体的需要,也能满足其它水体,如海水的需要。     

Significance of anion exchange in pentachlorophenol sorption by variable-charge soils

Sorption data and subsequent predictive models for evaluating acidic pesticide behavior on variable-charge soils are needed to improve pesticide management and environmental stewardship. Previous work demonstrated that sorption of pentachlorophenol (PCP), a model organic acid, was adequately modeled by accounting for pH-and pKa-dependent chemical speciation and using two organic carbon-normalized sorption coefficients; one each for the neutral and anionic species. Such models do not account for organic anion interaction to positively charged surface sites, which can be significant for variable-charge minerals present in weathered soils typical of tropical and subtropical regions. The role of anion exchange in sorption of ionizable chemicals by variable-charge soils was assessed by measuring sorption of PCP by several variable-charge soils from aqueous solutions of CaCl2, CaSO4, Ca(H2PO4)2 as a function of pH. Differences in sorption from phosphate and chloride electrolyte solutions were attributed to pentachlorophenolate interactions with anion exchange sites. Suppression of PCP sorption by phosphate ranged from negligible in a soil with essentially no positively charge sites, as measured by negligible anion exchange capacity, to as much as 69% for variable-charge soils. Pentachlorophenolate exchange correlated well with the ratio of pH-dependent anion exchange capacity to net surface charge. Sorption reversibility of PCP by both CaCl2 and Ca(H2PO4)2 solutions was also demonstrated. Results for PCP clearly demonstrate that sorption to anion exchange sites in variable-charge soils should be considered in assessing pesticide mobility and that phosphate fertilizer application may increase the mobility of acidic pesticides.     

Cellulose-based anion exchanger with tertiary amine functionality for the extraction of arsenic(V) from aqueous media

A novel cellulose-based anion exchanger (Cell-AE) with tertiary amine functionality was synthesized by graft polymerization reaction of cellulose and glycidyl methacrylate using N,N′-methylene-bis-acrylamide as a crosslinker and benzoyl peroxide as an initiator, followed by dimethylamine (amination) and acid (HCl) treatment. The chemical modification was confirmed by infrared spectroscopy and CHN analysis. The anion exchanger was used in batch processes to study AS(V) adsorption in solutions. The operating variables studied were pH, contact time, initial As(V) concentration, sorbent mass, and ionic strength. The process was affected by solution pH with an optimum adsorption occurring at pH 6.0. Adsorption equilibrium was achieved within 1 h. Increasing ionic strength of solution negatively affected the arsenic uptake. The adsorption process performed more than 99.0% of As(V) removal from an initial concentration of 25.0 mg/L. The process of adsorption followed pseudo-second-order kinetics. The adsorption equilibrium isotherm data were analyzed using the Langmuir, Freundlich, Redlich–Peterson and Langmuir–Freundlich equations. The Langmuir–Freundlich isotherm described the adsorption data over the concentration range 25–400 mg/L. The adsorption mechanism appears to be a ligand-exchange process. A simulated groundwater sample was treated with Cell-AE to demonstrate its efficiency in removing As(V). The adsorbed As(V) ions were desorbed effectively by a 0.1 M NaOH solution.     

Soil solid-phase controls lead activity in soil solution

Lead pollution of the environment is synonymous with civilization. It has no known biological function, and is naturally present in soil, but its presence in food crops is deemed undesirable. The concern regarding Pb is mostly due to chronic human and animal health effects, rather then phytotoxicity. However, not much is known about the chemistry and speciation of Pb in soils. We determined the activity of Pb2+, in near neutral and alkaline soils, representative of alluvial, desertic and calcareous soils of Egypt, using the competitive chelation method. Lead activity ranged from 10(-6.73) to 10(-4.83) M, and was negatively correlated with soil and soil solution pH (R2 = -0.92, P < 0.01 and R2 = -0.89, P < 0.01, respectively). It could be predicted in soil solution from the equation: log(Pb2+) = 9.9 - 2pH. A solubility diagram for the various Pb minerals found in soil was constructed using published thermodynamic data obtained from the literature, and our measured Pb2+ activities compared with this information. The measured Pb2+ activities were undersaturated with regard to the solubility of PbSiO3 in equilibrium with SiO2 (soil). However, they were supersaturated with regard to the solubilities of the Pb carbonate minerals PbCO3 (cerussite) and Pb3(CO3)2(OH)2 in equilibrium with atmospheric CO2 and hydroxide Pb(OH)2. They were also supersaturated with regard to the solubilities of the Pb phosphate minerals Pb3(PO4)2, Pb5(PO4)3OH, and Pb4O(PO4)2 in equilibrium with tricalcium phosphate and CaCO3. The activity of Pb2+ was not regulated by any mineral of known solubility in our soils, but possibly by a mixture of Pb carbonate and phosphate minerals.     

Cadmium binding by fractions of dissolved organic matter and humic substances from municipal solid waste compost

The agricultural practice of amending soils with composted municipal solid waste (MSW) adds significant amounts of organic matter and trace metals, including Cd. Under these conditions, soluble organic complexes of Cd formed in the compost may be more significant than previously thought, due to Cd bioavailability and mobility in the soil environment. To study the relative importance of different types of organic ligands in MSW compost for the binding of Cd, six fractions of the dissolved organic matter (DOM) in addition to humic acid (HA) and fulvic acid (FA) were extracted and their complexation of Cd quantified at pH 7 using an ion-selective electrode (ISE). The highest complexing capacities (CC) for Cd were found for the most humified ligands: HA (2386 micromol Cd g(-1) C of ligand), predialyzed FA (2468 micromol Cd g(-1) C), and HoA, a fulvic-type, easily soluble fraction (1042 micromol Cd g(-1) C). The differences in CC for Cd of the various organic ligands were not directly related to total acid-titratable or carboxylic groups, indicating the importance of sterical issues and other functional groups. The strength of association between Cd and the organic ligands was characterized by calculating stability constants for binding at the strongest sites (pK(int)) and modeling the distribution of binding site strengths. The pK(int) values of the DOM fractions ranged between 6.93 (HiN: polysaccharides) and 8.11 (HiB: proteins and aminosugars), compared with 10.05 for HA and 7.98 for FA. Hence, the highly complex and only partially soluble organic molecules from compost such as HA and FA demonstrated the highest capacity to sequester Cd. However, strong Cd binding of organic ligands containing N-functional groups (HiB) in addition to a high CC of soluble, humified ligands like HoA indicated the relevance of these fractions for the organic complexation of Cd in solution.     

Effects of ionic strength, temperature, and pH on degradation of selected antibiotics

Aqueous degradation rates, which include hydrolysis and epimerization, for chlortetracycline (CTC), oxytetracycline (OTC), tetracycline (TET), lincomycin (LNC), sulfachlorpyridazine (SCP), sulfadimethoxine (SDM), sulfathiazole (STZ), trimethoprim (TRM), and tylosin A (TYL) were studied as a function of ionic strength (0.0015, 0.050, or 0.084 mg/L as Na(2)HPO(4)), temperature (7, 22, and 35 degrees C), and pH (2, 5, 7, 9, and 11). Multiple linear regression revealed that ionic strength did not significantly affect (alpha = 0.05) degradation rates for all compounds, but temperature and pH affected rates for CTC, OTC, and TET significantly (alpha = 0.05). Degradation also was observed for TYL at pH 2 and 11. No significant degradation was observed for LNC, SCP, SDM, STZ, TRM, and TYL (pH 5, 7, and 9) under study conditions. Pseudo first-order rate constants, half-lives, and Arrhenius coefficients were calculated where appropriate. In general, hydrolysis rates for CTC, OTC, and TET increased as pH and temperature increased following Arrhenius relationships. Known degradation products were used to confirm that degradation had occurred, but these products were not quantified. Half-lives ranged from less than 6 h up to 9.7 wk for the tetracyclines and for TYL (pH 2 and 11), but no degradation of LIN, the sulfonamides, or TRM was observed during the study period. These results indicate that tetracyclines and TYL at pH 2 and 11 are prone to pH-mediated transformation and hydrolysis in some cases, but not the sulfonamides, LIN nor TRM are inclined to degrade under study conditions. This indicates that with the exception of CTC, OTC, and TET, pH-mediated reactions such as hydrolysis and epimerization are not likely removal mechanisms in surface water, anaerobic swine lagoons, wastewater, and ground water.     

Solubilization of mixed polycyclic aromatic hydrocarbons through a rhamnolipid biosurfactant

The solubilization of phenanthrene (PHE) and pyrene (PYR) by rhamnolipid biosurfactant was systematically investigated. The solubilities of both polycyclic aromatic hydrocarbons (PAHs) were increased linearly with the biosurfactant concentration at above critical micelle concentration. A competitive effect was observed between PHE and PYR. The solubility of PHE in a mixed system was lower than that in a single PAH system, whereas the solubility of PYR in a mixed system was enhanced. This is because the hydrophobicity of PYR is higher than that of PHE, so PYR is favored in the competitive solubilization. The combined effect of biosurfactant and dissolved organic matter (DOM) on PAH solubilization was also examined. Two kinds of DOM (derived from soil and from compost) were used. There was an obvious enhancement of solubility for PHE and PYR in systems with concurrence of DOM and biosurfacrant compared with systems with only DOM or biosurfactant; however, the enhancement in the mixed system was less than their additive. This could be explained as the formation of a DOM-biosurfactant complex. In addition, the solubility enhancement of PAHs in a compost-DOM system was higher than that in a soil-DOM system. This could be explained as functional group differences of two DOM types.     

Batch sorption dynamics and equilibrium for the removal of lead ions from aqueous phase using activated carbon developed from coffee residue activated with zinc chloride

Lignocellulosic materials are good precursors for the production of activated carbon. In this work, coffee residue has been used as raw material in the preparation of powder activated carbon by the method of chemical activation with zinc chloride for the sorption of Pb(II) from dilute aqueous solutions.The influence of impregnation ratio (ZnCl₂/coffee residue) on the physical and chemical properties of the prepared carbons was studied in order to optimize this parameter. The optimum experimental condition for preparing predominantly microporous activated carbons with high pore surface area (890 m²/g) and micropore volume (0.772 cm³/g) is an impregnation ratio of 100%. The developed activated carbon shows substantial capability to sorb lead(II) ions from aqueous solutions and for relative impregnation ratios of 75 and 100%, the maximum uptake is practically the same. Thus, 75% represents the optimal impregnation ratio.Batch experiments were conducted to study the effects of the main parameters such as contact time, initial concentration of Pb(II), solution pH, ionic strength and temperature. The maximum uptake of lead(II) at 25 °C was about 63 mg/g of adsorbent at pH 5.8, initial Pb(II) concentration of 10 mg/L, agitation speed of 200 rpm and ionic strength of 0.005 M. The kinetic data were fitted to the models of pseudo-first order and pseudo-second order, and follow closely the pseudo-second order model. Equilibrium sorption isotherms of Pb(II) were analyzed by the Langmuir, Freundlich and Temkin isotherm models. The Freundlich model gives a better fit than the others.Results from this study suggest that activated carbon produced from coffee residue is an effective adsorbent for the removal of lead from aqueous solutions and that ZnCl₂ is a suitable activating agent for the preparation of high-porosity carbons.     

Fate and transport of engineered nanomaterials in the environment

With the fast development of nanotechnology, engineered nanomaterials (ENMs) will inevitably be introduced into the various environment. Increasing studies showed the toxiccity of various ENMs, which raises concerns over their fate and transport in the environment. This review focuses on advances in the research on environmental transport and fate of ENMs. Aggregation and suspension behaviors of ENMs determining their fate and transport in aqueous environment are discussed, with emphasis on the influencing factors, including natural colloids, natural organic matter, pH, and ionic strength. Studies on the transport of ENMs in porous media and its influencing factors are reviewed, and transformation and organismcleansing, as two fate routes of ENMs in the environment, are addressed. Future research directions and outlook in the environmental transport and fate of ENMs are also presented.     

MANGANESE CYCLE IN IMPOUNDMENT WATER

Manganese entering impounded water will undergo a cyclic transformation. Oxidation precipitates manganese from top waters. At the bottom of the lake, biological activity will render manganese soluble by both intracellular as well as extracellular activity. The study was made to demonstrate that biological reduction and transformation, organometallic complexation, together with the presence of carbon dioxide and the lowering of pH all have some effect on the solubility of manganese. Dissolved manganese may be brought back to top waters during the lake overturn and therefore deteriorates the water quality.     

Coupled abiotic-biotic mineralization of 2,4,6-trinitrotoluene (TNT)

Munitions wastes such as TNT are widespread contaminants in soils and ground waters. We investigated a coupled abiotic-biotic treatment scheme for remediation of aqueous solutions of TNT. Mineralization of aqueous TNT (0.22 mM) was initially optimized with minimum reactant use (Fe3+ and H2O2) in light-assisted and dark, modified Fenton reactions at acidic and neutral pH. Complete TNT degradation occurred under all reaction conditions within 24 h. Using the optimum reactant concentrations, coupled abiotic-biotic reactions showed an increase in TNT mineralization, from 47 to 80%, after biomass addition to the acidic, dark Fenton-like reaction. Comparable increases of TNT mineralization were observed under neutral pH with similar reaction conditions. In light-assisted Fenton-like reactions at neutral pH, no increase in cumulative TNT mineralization (66%) was seen in coupled abiotic-biotic reactions. Abiotic photo-Fenton-like reactions alone, at acidic pH, produced complete TNT mineralization and required no biotic assistance. While light-enhanced Fenton reactions alone can provide high levels of TNT mineralization, the dark abiotic-biotic reaction scheme has perhaps a wider use due to a similar extent of TNT mineralization in the absence of light, leading to possible applications in soil slurry and in situ processes in the subsurface.     

Immobilization of nickel and other metals in contaminated sediments by hydroxyapatite addition

Batch experiments were conducted to evaluate the ability of hydroxyapatte (HA) to reduce the solubility of metals, including the primary contaminants of concern, Ni and U, from contaminated sediments located on the Department of Energy's Savannah River Site, near Aiken, SC. Hydroxyapatitie was added to the sediments at application rates of 0, 5, 15.8, and 50 g kg-1. After equilibrating in either 0.02 M KCl or 0.01 M CaCl2, the samples were centrifuged and the supernatants filtered prior to metal, dissolved organic C, and PO4 analyses. The treated soils were then air-dried and changes in solid-phase metal distribution were evaluated using sequential extractions and electron-based microanalysis techniques. Hydroxyapatite was effective at reducing the solubility of U and, to a lesser degree, Ni. Hydroxyapatite was also effective in reducing the solubility of Al, Ba, Cd, Co, Mn, and Pb. Sequential extractions indicate that HA transfers such metals from more chemically labile forms, such as the water-soluble and exchangeable fractions, by altering solid-phase speciation in favor of secondary phosphate precipitates. Hydroxyapatite effectiveness was somewhat reduced in the presence of soluble organics that likely increased contaminant metal solubility through complexation. Arsenic and Cr solubility increased with HA addition, suggesting that the increase in pH and competition from PO4 reduced sorption of oxyanion contaminants. Energy dispersive x-ray (EDXA) analysis conducted in the transmission electron microscope (TEM) confirmed that HA amendment sequesters U, Ni, Pb, and possibly other contaminant metals in association with secondary Al-phosphates.     

Fungal inoculum properties: extracellular enzyme expression and pentachlorophenol removal in highly contaminated field soils

This study was conducted to improve the pentachlorophenol (PCP) bioremediation ability of white-rot fungi in highly contaminated field soils by manipulating bioaugmentation variables. These were the dry weight percentage of fungal inoculum addition (31-175 g kg(-1)), PCP concentration (100-2137 mg kg(-1) PCP), fungal inoculum formulation, and time (1-7 wk). Five fungal isolates were used: the New Zealand isolates Trametes versicolor (L.: Fr.) HR131 and Trametes sp. HR577; the North American isolates Phanerochaete chrysosporium Burds. (two isolates) and Phanerochaete sordida (Karst.) Erikss. & Ryv. Pentachlorophenol removal, manganese peroxidase, and laccase activity, and the formation of chloroanisoles in the contaminated field soils were measured. The majority of PCP removed by the Trametes isolates was in the first week after bioaugmentation. The maximum PCP removal by the fungi varied from 50 to 65% from a 1065 mg kg(-1) PCP contaminated field soil. Pentachlorophenol was preferentially converted to pentachloroanisole (PCA) by the Phanerochaete isolates (>60%), while 2 to 9% of the PCP removed by two Trametes isolates was converted to PCA. A pH increase was measured following bioaugmentation that was dependent on PCP concentration, fungal inoculum addition, and formulation. This, together with rapid initial PCP removal, possibly changed the bioavailability of the remaining PCP to the fungi and significantly decreased the sequestering of PCP in the contaminated field soils. The research supports the conclusion that New Zealand Trametes spp. can rapidly remove PCP in contaminated field soils. Bioavailability and extractability of PCP in the contaminated field soil may significantly increase after bioaugmentation.     

Oxidation and detoxification of pentachlorophenol in aqueous phase by ozonation

The degradation and detoxification performance of ozonation in treating pentachlorophenol (PCP) contaminated wastewater was determined. All experiments were conducted in a bench scale glass column equipped with ceramic diffuser and a lab-scale ozone generator under ambient temperature and pH 7. The decomposition rate of PCP in this study was primarily controlled by the ozone mass transfer rate from gas to liquid phases. Principal intermediates found were 2,3,4,6- and 2,3,5,6-tetrachlorophenols (TeCP) and phenol. PCP seems to be more vulnerable to ozone than its intermediates. A bioluminescence technique was used to evaluate the toxicity of PCP with Vibrio fisheri NRRL B-11177 as the test bacterium, and the EC(50) of PCP was found to be 1.0 mg l(-1). Detoxification occurred as the PCP and TeCP reacted with ozone and decomposed to less chlorinated congeners and phenol.     

Removal of natural organic matter by cationic hydrogel with magnetic properties

Magnetic cationic hydrogel (MCH) was synthesized, and its removal efficiency and mechanisms in regard to natural organic matter (NOM, represented by humic acid and fulvic acid) from the aqueous environment were studied. The effects of time, adsorbent dosage, initial pH, ionic strength, background ions, and NOM types were also investigated. MCH was characterized and found to have a strong magnetic character, yielding an extra advantage for recycling and reuse. Batch studies showed that the removal of Aldrich humic acid (AHA) by MCH was effective. The main mechanism for the removal of NOM is believed to be due to electrostatic interaction. NOM with larger molecular weight tended to be preferentially removed. Solutions with low pH, high ionic strength, and background electrolytes containing calcium, sulfate and bicarbonate were unfavorable for AHA removal. The adsorption-desorption of MCH was evaluated in three cycles, and demonstrated high regeneration rates.     

Cadmium solubility and sorption in a long-term sludge-amended arable soil

Cadmium solubility and sorption in an arable clay loam soil that had received sewage sludge for 41 years were compared to an unsludged control in batch studies. Soil pH dominated Cd sorption, explaining >92% of the variation in Kd values in both treatments. At any pH, Cd sorption was apparently slightly but significantly (p < 0.05) smaller in the sludge-amended soil compared to the control, even though the organic carbon content was 70% larger and the ammonium oxalate-extractable iron content was roughly doubled. Correction for dissolved organic carbon (DOC) complexation with the speciation model WHAM reduced the difference in sorption between treatments, but the sludged soil still had significantly smaller Kd values (p < 0.01). Batch equilibrations without addition of Cd showed that there was no significant difference in the solubility of "native" cadmium (defined as EDTA-extractable Cd) in sludged and control soils. The reason for the lack of increase in Cd sorption in the sludge-amended soil has not been established, but it may be due to competition for sorption sites on humic compounds with sludge-derived Fe and trace metals such as zinc. The fact that the pyrophosphate-extractable (i.e., organically associated) iron content was seven times larger in the sludged soil provides some supporting evidence for this hypothesis.