Diopside-based glass-ceramics from MSW fly ash and bottom ash

By utilising MSW fly ash from the Shanghai Yuqiao municipal solid waste (MSW) incineration plant as the main raw material, diopside-based glass-ceramics were successfully synthesized in the laboratory by combining SiO(2), MgO and Al(2)O(3) or bottom ash as conditioner of the chemical compositions and TiO(2) as the nucleation agent. The optimum procedure for the glass-ceramics is as follows: melting at 1500 degrees C for 30 min, nucleating at 730 degrees C for 90 min, and crystallization at 880 degrees C for 10h. It has been shown that the diopside-based glass-ceramics made from MSW fly ash have a strong fixing capacity for heavy metals such as lead (Pb), chromium (Cr), cadmium (Cd) etc.     

Ceramic processing of incinerator bottom ash

The <8 mm fraction of aged incinerator bottom ash from a commercial incinerator (energy from waste) plant has been collected at regular intervals, characterised and processed to form ceramic materials. Ashes were sieved, wet ball milled, dried, compacted and sintered at temperatures between 1080 and 1115 degrees C. Variations in the chemical composition and mineralogy of the milled ash, and the mineralogy, physical properties and leaching of sintered products have been assessed. Milling produces a raw material with consistent chemical and mineralogical composition with quartz (SiO(2)), calcite (CaCO(3)), gehlenite (Ca(2)Al(AlSi)O(7)) and hematite (Fe(2)O(3)) being the major crystalline phases present. Different batches also milled to give consistent particle size distributions. Sintering milled incinerator bottom ash at 1110 degrees C produced ceramics with densities between 2.43 and 2.64 g/cm(-3) and major crystalline phases of wollastonite (CaSiO(3)) and diopside (CaMgSi(2)O(6)). The sintered ceramics had reduced acid neutralisation capacity compared to the as-received ash and exhibited reduced leaching of Ca, Mg, Na and K under all pH conditions. The leaching of heavy metals was also significantly reduced due to encapsulation and incorporation into glassy and crystalline phases, with Cu and Al showing greatly reduced leaching under alkali conditions.     

Metal leachability, heavy metals, polycyclic aromatic hydrocarbons and polychlorinated biphenyls in fly and bottom ashes of a medical waste incineration facility

Medical waste from hospitals and other healthcare institutions has become an imperative environmental and public safety problem. Medical waste in Greece has become one of the most urgent environmental problems, because there are 14,000 tons produced annually, of which only a small proportion is incinerated. In the prefecture of Attica there is only one modern municipal medical waste incinerator (started 2004) burning selected infectious hospital waste (5-6 tons day(-1)). Fly and bottom residues (ashes) are collected and stored temporarily in barrels. High values of metal leachability prohibit the landfilling of these ashes, as imposed by EU directives. In the present study we determined quantitatively the heavy metals and other elements in the fly and bottom ashes of the medical waste incinerator, by inductively coupled plasma emission spectrometry (ICP) and by energy dispersive X-ray analysis (EDAX). Heavy metals, which are very toxic, such as Pb, Cd, Ni, Cr, Cu and Zn were found in high concentrations in both fly and bottom ashes. Metal leachability of fly and bottom ashes by water and kerosene was measured by ICP and the results showed that toxic metals in both ashes, such as Pb, Cr, Cd, Cu and Zn, have high leaching values. These values indicate that metals can become soluble and mobile if ash is deposited in landfills, thus restricting their burial according to EU regulations. Analysis of polychlorinated biphenyls and polycyclic aromatic hydrocarbons in fly and bottom ashes showed that their concentrations were very low. This is the first known study in Greece and the results showed that incineration of medical waste can be very effective in minimizing the most hazardous and infectious health-care waste. The presence of toxic metals with high leachability values remains an important draw back of incineration of medical waste and various methods of treating these residues to diminish leaching are been considered at present to overcome this serious technical problem.     

Chemical durability of glasses obtained by vitrification of industrial wastes

The vitrification of zinc-hydrometallurgy wastes, electric arc furnace dust (EAFD), drainage mud, and granite mud was shown to immobilize the hazardous components in these wastes. Batch compositions were prepared by mixing the wastes with glass-cullet and sand to force the final glass composition into the glass forming region of the SiO2-Fe2O3-(CaO, MgO) system. The vitrification was carried out in the 1400-1450 degrees C temperature range followed by quenching in water or on stainless steel mold. The United States (US) Environmental Protection Agency (EPA) toxic characterization leaching procedure (TCLP) test was used as a standard method for evaluating the leachability of the elements in the glasses and glass-ceramics samples made with different percentages of wastes. The results for EAFD glasses highlighted that the chemical stability is influenced by the glass structure formed, which, in turn, depends on the Si/O ratio in the glass. The chemical durability of jarosite glasses and glass-ceramics was evaluated by 24 h contact in NaOH, HCl and Na2CO3, at 95 degrees C. Jarosite glass-ceramics containing pyroxene (J40) are more durable than the parent glass in HCl. Jarosite glass-ceramics containing magnetite type spinels (J50) have a durability similar to the parent glass and even lower in HCl because the magnetite is soluble in HCl.     

Composite materials based on wastes of flat glass processing

Glass mirrors scrap and poly (vinyl) butiral waste (PVB) obtained from flat glass processing plants were investigated as raw materials to produce composites. The emphasis was on studying the influence of milled glass mirror waste contents on properties of composites produced with PVB. The characterization involved: elongation under rupture, water absorption, tensile strength and elastic modulus tests. The results showed that the composite containing 10 wt% of filler powder had the best properties among the compositions studied. The influence of the time of exposure in humid atmosphere on the composite properties was investigated. It was found that the admixture of PVB iso-propanol solution to the scrap of glass mirrors during milling provided stabilization of the properties of the composites produced.     

Controlled combustion tests and bottom ash analysis using household waste with varying composition

The influence of the co-combustion of household waste with either sewage sludge, shredder fluff, electronic and electrical waste (WEEE) or PVC on the bottom ash quality and content was investigated under controlled laboratory conditions using a pot furnace. This laboratory approach avoids the interpretation problems related to large variations in input waste composition and combustion conditions that are observed in large scale MSW incinerators. The data for metals content, transfer coefficients and leaching values are presented relative to data for a base household waste composition that did not contain any of the added special wastes. The small WEEE invited direct measurement of precious metals content in the ashes, where measurement accuracy is facilitated by using only mobile phone scrap for small WEEE. The analyses were carried out for different particle size ranges that are of relevance to the recyclability of metals and minerals in the ashes. Positive correlations were found between elements content of the input waste and the bottom ashes, and also between increased levels of Cl, Mo and Cu in the input waste and their leaching in the bottom ashes. These correlations indicate that addition of PVC, small WEEE and shredder fluff in input waste can have a negative influence on the quality of the bottom ashes. Enrichment of Au and Ag occurred in the fractions between 0.15 and 6 mm. The precious metals content represents an economically interesting intrinsic value, even when the observed peak values are properly averaged over a larger volume of ashes. Overall, it has been shown that changes in quality and content of bottom ashes may be traced back to the varied input waste composition.     

The behaviour of ashes and heavy metals during the co-combustion of sewage sludges in a fluidised bed

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.     

Characterization of bottom ash in municipal solid waste incinerators for its use in road base

Incineration of municipal solid wastes (MSWs) produces by-products which can be broadly classified as bottom and fly ashes. Since MSW incineration started, possibilities other than landfilling the incineration residues have been sought; most initiatives in this sense tend to use these residues as aggregate substitute in pavements and other road construction elements. The main goal of the present work is the physical and chemical characterization of the local incineration bottom ash towards its eventual re-utilization. The study includes not only the specific aspects regarding its role as pavement element, but also the assessment of the environmental effects. Therefore, together with the determination of physical (moisture content, apparent and bulk densities, crystallinity, etc.) and engineering properties (particle size distribution, abrasion and impact resistance, etc.), full chemical characterization of the bottom ash and the study of leaching as a function of aging time have been undertaken. The results obtained indicate that the metal content of both the raw bottom ash and its leachates fulfill the environmental regulations provided that the bottom ash is stored for at least one month. Engineering properties of the bottom ash are close to those of natural aggregates and, thus, road-construction use of these residues seems to be feasible.     

Recovery of MSWI and soil washing residues as concrete aggregates

The aim of the present work was to study if municipal solid waste incinerator (MSWI) residues and aggregates derived from contaminated soil washing could be used as alternative aggregates for concrete production.Initially, chemical, physical and geometric characteristics (according to UNI EN 12620) of municipal solid waste incineration bottom ashes and some contaminated soils were evaluated; moreover, the pollutants release was evaluated by means of leaching tests. The results showed that the reuse of pre-treated MSWI bottom ash and washed soil is possible, either from technical or environmental point of view, while it is not possible for the raw wastes.Then, the natural aggregate was partially and totally replaced with these recycled aggregates for the production of concrete mixtures that were characterized by conventional mechanical and leaching tests. Good results were obtained using the same dosage of a high resistance cement (42.5R calcareous Portland cement instead of 32.5R); the concrete mixture containing 400 kg/m³ of washed bottom ash and high resistance cement was classified as structural concrete (C25/30 class). Regarding the pollutants leaching, all concrete mixtures respected the limit values according to the Italian regulation.     

Behavior of TiO2 nanoparticles during incineration of solid paint waste: A lab-scale test

In order to assess the potential impacts posed by products containing engineered nanoparticles, it is essential to generate more data about the release of these particles from products’ life cycle. Although first studies were performed to investigate the release of nanoparticles from use phase, very few data are available on the potential release from recycling or disposal of nano-enhanced products.In this work, we investigated the behavior of TiO₂ nanoparticles from incineration of solid paint waste containing these particles. Solid paint debris with and without TiO₂ nanoparticles were treated in a lab scale incineration plant at 950 °C (combustion temperature) and in oxidizing atmosphere. The obtained ashes were also vitrified with additives and the release of Ti was finally evaluated by leaching test. From our incineration lab-scale experiment, we did not observe a release of TiO₂ nanoparticles into the atmosphere, and Ti was attached to the surface of obtained solid residues (i.e. ashes). The characterization of ashes showed that TiO₂ nanoparticles reacted during the incineration to give calcium titanate. Finally, a very low release of Ti was measured, less 1 mg/kg, during the leaching test of ashes vitrified with glass cullet and feldspathic inert. Our work suggests that TiO₂ nanoparticles added in paints may undergo to physicochemical transformation during the incineration, and that Ti found in ashes may be strongly immobilized in glass matrix. Since this conclusion is based on lab-scale experiment, further research is required to identify which nanoparticles will be emitted to the environment from a real-word-incineration system of household hazardous waste.     

A study of Cr(VI) in ashes from fluidized bed combustion of municipal solid waste: leaching, secondary reactions and the applicability of some speciation methods

The use of the fluidized bed technique for the combustion of municipal solid waste is a rather new concept. This type of combustor produces ash residues with somewhat different properties than the residues generated from the traditional mass burn techniques. Therefore, chemical characterization and the investigation of toxic metals behavior during ash water reactions are necessary for the safe disposal of these residues. In the present work, the total elemental composition, mineralogy and leaching behavior of ashes from the combustion of municipal solid waste in a fluidized bed combustion boiler have been investigated. The cyclone ash and, in particular, the filter ash contained considerable amounts of soluble substances, thus giving leachates with high levels of Cl-, Na+, K+, Ca2 + and Al(IIl). On the other hand, the two ash fractions taken in the boiler, the bottom and hopper ashes, were much more stable with respect to the release of salts and heavy metals. Since Cr(VI) is mobile and toxic its release from combustion residues can pose environmental problem. Even though the total Cr contents were similar in all ashes studied, the bottom ash gave about a thousand times higher levels of Cr(VI) in test leachates than the hopper, cyclone and filter ashes. However, it was found that the leached amount of Cr(VI) from the bottom ash decreased significantly when bottom ash was mixed with the hopper ash. The most probable cause for this decrease is the coupled oxidation of Al(0) to Al(III) and reduction of dissolved Cr(VI) to Cr(III). This finding that the mixing of two ash streams from the same boiler could result in the immobilization of Cr may point at a simple stabilization method. Selective extraction of water soluble, exchangeable and sparingly soluble forms of Cr(VI) was also investigated. Extraction methods were evaluated for their suitability for ash matrixes. It was found that interferences due to the presence of reducing substances in some ash materials may occur.     

Characterization of alkali-activated thermally treated incinerator bottom ash

The fine fraction (<14mm) of incinerator bottom ash (IBA) obtained from a UK energy from waste plant has been milled and thermally treated at 600, 700, 800 and 880 degrees C. Treated materials have been activated with Ca(OH)(2) (10wt%) and the setting times and compressive strengths at different curing times measured. In addition to decomposition of CaCO(3) to CaO, thermal treatment increases the content of gehlenite (Ca(2)Al(2)SiO(7)), wollastonite (CaSiO(3)) and mayenite (Ca(12)Al(14)O(33)). Thermally treated samples were significantly more reactive than milled IBA and heating to 700 degrees C produced a material which rapidly set. Silica, gehlenite and wollastonite were the main crystalline phases present in hydrated samples and a mixed sulphate-carbonate AFm-type phase (Ca(4)Al(2)O(6)(CO(3))(0.67)(SO(3))(0.33).11H(2)O) formed. Significant volumes of gas were generated during curing and this produced a macro-porous microstructure that limited strength to 2.8MPa. The new materials may have potential for use as controlled low-strength materials.     

Comparative studies of waste incineration bottom ashes from various grate and firing systems,conducted with respect to mineralogical and geochemical methods of examination

Mineralogical and geochemical techniques can be used successfully to characterize and evaluate bottom ashes produced in waste incineration. At the present time, it is not quite clear to what extent the mineral phase compositions and the content of main elements and heavy metal concentrations of bottom ashes are influenced by the conditions of combustion. Once the location of heavy metals in or with specific minerals is known, it may be considered, in the light of technical possibilities, whether a change in temperature or in the residence time of waste in the combustion chamber could be sufficient to remove these components from their mineral phases.     

Petrogenetic characteristics of molten slag from the pyrolysis/melting treatment of MSW

MSW slag materials derived from four pyrolysis melting plants in Japan were studied from the viewpoint of petrology in order to discriminate the glass and mineral phases and to propose a petrogenetic model for the formation process of molten slag. Slag material is composed of two major components: melt and refractory products. The melt products that formed during the melting process comprise silicate glass, and a suite of minerals as major constituents. The silicate glass is essentially composed of low and high silica glass members (typically 30% and 50% of SiO(2), respectively), from which minerals such as spinels, melilite, pseudowollastonite, and metallic inclusions have been precipitated. The refractory products consist mainly of pieces of metals, minerals and lithic fragments that survived through the melting process. Investigations demonstrated that the low silica melts (higher Ca and Al contents) were produced at upper levels of high temperature combustion chamber HTCC, at narrower temperature ranges (1250-1350 degrees C), while the high silica melts formed at broader temperature ranges (1250-1450 degrees C), at the lower levels of HTCC. The recent temperature ranges were estimated by using CaOAl(2)O(3)SiO(2) (CAS) ternary liquidus diagram that are reasonably consistent with those reported for a typical combustor. It was also understood that the samples with a higher CaO/SiO(2) ratio (>0.74-0.75) have undergone improved melting, incipient crystallization of minerals, and extensive homogenization. The combined mineralogical and geochemical examinations provided evidence to accept the concept of stepwise generation of different melt phases within the HTCC. The petrogenesis of the melt products may therefore be described as a two-phase melt system with immiscible characteristics that have been successively generated during the melting process of MSW.     

Physical and mechanical properties of cement-based products containing incineration bottom ash

This paper presents the results of a wider experimental programme conducted in the framework of the NNAPICS ("Neural Network Analysis for Prediction of Interactions in Cement/Waste Systems") project funded by the European Commission and a number of industrial partners under Brite-EuRamIII. Based on the fact that bottom ashes from waste incineration are classified as non-hazardous wastes according to the European Waste Catalogue, the aim of the present work was to investigate the feasibility of addressing the potential use of such residues in cement-based mixtures. This issue was suggested by the analysis of the properties of different bottom ashes coming from Italian municipal and hospital solid waste incinerators, which showed a chemical composition potentially suitable for such applications. Different mixes were prepared by blending bottom ash with ordinary Portland cement in different proportions and at different water dosages. The solidified products were tested for setting time and bulk density, unconfined compressive strength and evaporable water content at different curing times. The results of the experimental campaign were analysed through a statistical procedure (analysis of variance), in order to investigate the effect of mixture composition (waste replacement level and water dosage) on the product properties.     

Use of vitrified MSWI bottom ashes for concrete production

Bottom ashes from a north Italian municipal solid waste incinerator (MSWI) were vitrified at 1450 degrees C without adding any vitrifying agent, then ground and sieved to different granulometry (ranging from 50 microm to 20mm), and used as filler, sand, or aggregate for concrete. Samples were characterized via slump tests (UNI 9418), alkali-silica reactivity (UNI 8520/22 and ASTM C 298), and compression strength tests (UNI 6132, 6132/72, 6686/72), and compared to reference samples obtained without vitrified bottom ashes (VBA). Our results show that vitrified bottom ashes are unsuitable as a sand substitute; however, concrete containing up to 20 wt.% of VBA filler used as a substitute for cement and up to 75 vol.% of VBA as a substitute for natural aggregate retains the same mechanical properties as reference samples. Alkali-silica or other detrimental reactions were not observed in VBA-containing concrete samples after a period of two years. The results of this work demonstrate that vitrified bottom ashes from MSWI can be used instead of natural aggregates in mortar and concrete production.     

Corrosion behavior of glass and glass-ceramics made of municipal solid waste incinerator fly ash

Glasses and glass-ceramics were prepared by melting municipal solid waste (MSW) incinerator fly ash and their corrosion properties were evaluated. Corrosion of both materials proceeded in two different steps. At the initial stage, the corrosion process is a diffusion-controlled process. After approximately 10 h at the initial stage, weight losses increased linearly with time due to the total dissolution of glasses or glass-ceramics. Leaching of heavy metals from glasses and glass-ceramics were well within international environmental regulations. Corrosion proceeded uniformly in fly ash glass while Na2CaSiO4 crystalline phase was preferentially dissolved in the glass-ceramics.     

Release of salts from municipal solid waste combustion residues

Residues from fluidized bed combustion of municipal solid waste were investigated with respect to their leaching behavior and possible extraction of salts. The total water extractable amounts of Na, K, Ca, Cl(-), Br(-), F(-) and SO(4)(2-) along with the total dissolved solids of bottom, hopper, cyclone and bag house filter ashes were determined. A simple multistage washing process (using water as the extraction medium) was tested in lab scale experiments. The effect of variations in parameters, such as water to ash weight ratio, contact time, temperature and number of extraction steps was investigated. The leaching behavior of untreated and washed cyclone and bag house filter ashes was evaluated by a two-step batch-leaching test, i.e. the CEN test. The ashes investigated in this study can be arranged according to their decreasing water extractable contents and total dissolved solids as follows: filter ash > cyclone ash > hopper ash > bottom ash. A triple extraction with water at liquid to solid ratio 2 and extraction time 5 min gave the best results for the extraction of Ca, Na, K, Cl(-) and SO(4)(2-) from the cyclone as well as from the filter ashes. The leached amounts of salts in the CEN test performed on the washed cyclone ash were considerably lower than the corresponding amounts released from the unwashed ash. Thus, the washed cyclone ash was made more stable with respect to salt leachability. On the other hand, large amounts of salts were leached from the washed filter ashes as well as from unwashed filter ashes. Therefore, it can be concluded that three stage water extraction is not a suitable stabilization method for this type of filter ashes.     

Chemical properties of heavy metals in typical hospital waste incinerator ashes in China

Incineration has become the main mechanism for hospital waste (HW) disposal in China after the outbreak of Severe Acute Respiratory Syndrome (SARS) in 2003. However, little information is available on the chemical properties of the resulting ashes. In the present study, 22HW ash samples, including 14 samples of bottom ash and eight samples of fly ash, were collected from four typical HW incineration plants located across China. Chemical analysis indicated that the HW ashes contained large amounts of metal salts of Al, Ca, Fe, K, Mg, Na with a concentration range of 1.8-315gkg(-1). Furthermore, the ashes contained high concentrations of heavy metals such as Ag, As, Ba, Bi, Cd, Cr, Cu, Mn, Ni, Pb, Ti, Sb, Sn, Sr, Zn with a vast range of 1.1-121,411mgkg(-1), with higher concentrations found in the fly ash samples. Sequential extraction results showed that Ba, Cr, Ni and Sn are present in the residual fraction, while Cd existed in the exchangeable and carbonate fractions. As, Mn, Zn existed in the Fe-Mn oxide fraction, Pb was present in the Fe-Mn oxide and residual fractions, and Cu was present in the organic matter fraction. Furthermore, toxicity characteristic leaching procedure (TCLP) results indicated that leached amounts of Cd, Cu and Pb from almost all fly ash samples exceeded the USEPA regulated levels. A comparison between the HW ashes and municipal solid waste (MSW) ash showed that both HW bottom ash and fly ash contained higher concentrations of Ag, As, Bi, Cd, Cr, Cu, Pb, Ti, and Zn. This research provides critical information for appropriate HW incineration ash management plans.     

Utilization of municipal solid waste bottom ash and recycled aggregate in concrete

In the combustion process of municipal solid waste (MSW), bottom ash (BA) represents the major portion of the solid residue. Since BA is composed of oxides, especially SiO(2) and CaO, the feasibility of its application in concrete as a substitute for cement was tested. It was found that at the age of 28 days, the flexural and compressive strengths of the binder linearly decrease at the rate of 0.03 and 0.02 MPa per wt% of BA in the binder, respectively. According to the results it may be recommended to replace up to 15 wt% of cement by BA and to use such binder where a low strength of concrete elements is required. Furthermore, the aggregate used for low strength concrete need not be of a very good quality. Therefore, gravel aggregate was partially replaced by recycled aggregate (RA). Consistency measured by slump was significantly reduced (>50%) when BA or/and RA were introduced into the mixture. However, concrete density and compressive strength were not affected and were approximately 2300 kg/m(3) and approximately 40 MPa, respectively.