Individual and simultaneous degradation of brominated high impact polystyrene and brominated acrylonitrile-butadiene-styrene and removal of heteroelements (Br,N, and O) from degradation oil by multiphase catalytic systems

Brominated high-impact polystyrene (HIPS-Br), which contained decabromodiphenyl ether flame retardant, and brominated acrylonitrile butadiene styrene (ABS-Br), which contained bromine-containing epoxy-type flame retardant, were degraded at 450°C individually and in a 1/1 mixture by a thermal and catalytic procedure using folded sheet mesoporous (FSM) and ZSM-5 zeolite in liquid phase contact mode. The two polymers produced similar degradation oils but at a higher yield for HIPS-Br. However, the composition and distribution of Br-, N-, and O-containing compounds depended on the type of flame retardant in HIPS-Br and ABS-Br. Multiphase catalytic systems consisting of FSM in liquid phase contact mode and various CaH-, FeO-, CoMo-, and NiMo-based catalysts, or combinations of these catalysts, in vapor phase contact mode were used to decrease the amount of heteroatoms (Br, N, and O) in the degradation oils. Each system gave particular results in terms of mass balance and concentrations of heteroatoms. A FSM (liquid phase contact)/CaHC (vapor phase contact) combination was the best catalytic system to remove Br-, N-, and O-containing compounds from degradation oils.     

Effect of heating rate on the pyrolysis of high-impact polystyrene containing brominated flame retardants: fate of brominated flame retardants

In the case of plastics containing brominated flame retardants, various brominated organic compounds, including polybrominated dibenzodioxins and dibenzofurans, are yielded when they are degraded. In order to reduce the hazard that might be generated during after-live treatment, the behaviour of flame retarded high-impact polystyrene containing decabromo diphenylether and antimony oxide (Sb₂O₃), was investigated using several heating programs. It was found that the separation of the thermal process into two steps divided at 330?°C makes it possible to obtain an oil fraction rich in brominated compounds at low temperatures and an oil fraction depleted in brominated compounds at high temperatures. The low temperature oil contained a high concentration of SbBr₃ and dibromodibenzofurans. Various brominated compounds with a low volatility and 1-bromo-1-phenylethane from the reaction of HBr with styrene were among the substances in the high temperature oil. The concentration of brominated compounds was reduced from 6?wt% for degradation in a single step to below 1?wt% in the high temperature oil in the two step process.     

十溴联苯醚环境修复技术的研究进展

介绍了溴代阻燃剂十溴联苯醚（BDE-209）环境修复技术的研究进展。从光降解、零价铁降解、生物降解3个方面对BDE-209的降解机理和降解后的产物进行了介绍。BDE-209经光照、厌氧微生物、零价铁的脱溴作用后,降解成低溴代联苯醚产物;好氧微生物利用低溴代联苯醚作为生长碳源,将其在酶的作用下开环降解,进入三羧酸循环或彻底分解成CO₂和H₂O。提出应采用多种方法协同作用,更有效地降解多溴联苯醚化合物。     

Development of a catalytic dehalogenation (Cl,Br) process for municipal waste plastic-derived oil

Dehalogenation is a key technology in the feedstock recycling of mixed halogenated waste plastics. In this study, two different methods were used to clarify the effectiveness of our proposed catalytic dehalogenation process using various carbon composites of iron oxides and calcium carbonate as the catalyst/sorbent. The first approach (a two-step process) was to develop a process for the thermal degradation of mixed halogenated waste plastics, and also develop dehalogenation catalysts for the catalytic dehydrochlorination of organic chlorine compounds from mixed plastic-derived oil containing polyvinyl chloride (PVC) using a fixed-bed flow-type reactor. The second approach (a single-step process) was the simultaneous degradation and dehalogenation of chlorinated (PVC) and brominated (plastic containing brominated flame retardant, HIPS–Br) mixed plastics into halogen-free liquid products. We report on a catalytic dehalogenation process for the chlorinated and brominated organic compounds formed by the pyrolysis of PVC and brominated flame retardant (HIPS–Br) mixed waste plastics [(polyethylene (PE), polypropylene (PP), and polystyrene (PS)], and also other plastics. During dehydrohalogenation, the iron- and calcium-based catalysts were transformed into their corresponding halides, which are also very active in the dehydrohalogenation of organic halogenated compounds. The halogen-free plastic-derived oil (PDO) can be used as a fuel oil or feedstock in refineries.     

Recovery of benzene-rich oil from the degradation of metal- and metal oxide-containing poly(ethylene terephthalate) composites

Pure poly(ethylene terephthalate) (PET) resin and metal-/metal oxide-containing PET composites were thermally decomposed in the presence of Ca(OH)₂ using a tube reactor. The effects of batch and continuous processing, the presence of Ca(OH)₂, and PET size on benzene production were investigated. A maximum benzene yield and purity of 82.9 % and 78.8 wt%, respectively, were obtained at 700 °C in the presence of Ca(OH)₂ when using small PET particles; further, a continuous feed reactor was favored over a batch reactor. Effective contact between PET and Ca(OH)₂ was important in the PET degradation, which promoted hydrolysis of PET and decarboxylation of terephthalic acid, whereas pyrolysis was suppressed. Furthermore, the results of thermal decomposition of PET-based waste—PET-based X-ray films, magnetic tape, and prepaid cards—indicated that the metal and metal oxides contained in the waste had no significant catalytic effect on PET degradation or on the recovery of benzene-rich oil in the presence of Ca(OH)₂.     

Aminolysis and aminoglycolysis of waste poly(ethylene terephthalate)

This paper describes the chemical degradation of waste poly(ethylene terephthalate) (PET) with polyamines or triethanolamine, the characteristics of the products, and a search for ways to use these products. Solvolysis of the polymer ester bonds was caused by diethylenetriamine, triethylenetetramine, and their mixtures, as well as mixtures of triethylenetetramine and p-phenylenediamine or triethanolamine. Products of aminolysis or aminoglycolysis of PET obtained in reactions performed at 200–210°C (with a molar ratio of the recurrent polymer unit to amine of 1 : 2) have been characterized using nuclear magnetic resonance (NMR). Viscosity and hydroxyl number measurements have been done for PET/triethanolamine products. Substances from aminolytical reactions with polyamines were tested as hardeners for liquid epoxy resins, and the product of polymer aminoglycolysis with triethanolamine was tested as an epoxy resin hardener, e.g., for water-borne paints, and a polyol component for rigid polyurethane foams. The compositions of epoxy resin hardeners have been characterized using DSC and rheometry. Comparative analyses of the hardened epoxy materials have been done on the basis of glass temperature and mechanical properties data, as well as some specific properties of the coating materials and rigid polyurethane foams. Received: September 15, 2000 / Accepted: September 21, 2000     

Thermocatalytic Degradation of High Density Polyethylene into Liquid Product

Thermocatalytic degradation of high density polyethylene (HDPE) was carried out using acid activated fire clay catalyst in a semi batch reactor. Thermal pyrolysis was performed in the temperature range of 420–500 °C. The liquid and gaseous yields were increased with increase in temperature. The liquid yield was obtained 30.1 wt% with thermal pyrolysis at temperature of 450 °C, which increased to 41.4 wt% with catalytic pyrolysis using acid activated fire clay catalyst at 10 wt% of catalyst loading. The composition of liquid products obtained by thermal and catalytic pyrolysis was analyzed by gas chromatography-mass spectrometry and compounds identified for catalytic pyrolysis were mainly paraffins and olefins with carbon number range of C₆–C₁₈. The boiling point was found in the range of commercial fuels (gasoline, diesel) and the calorific value was calculated to be 42 MJ/kg.     

Effect of Decalin Solvent on the Thermal Degradation of HDPE

The thermal cracking of HDPE in presence of different amounts of decalin was studied and compared with the reaction carried out in the absence of solvent. The decalin favours the mass and heat transfer during the reaction. In addition, it modifies the thermal degradation mechanism, which facilitates the formation of specific products. The use of decalin substantially increases the C₅–C₃₂ yield in comparison with the solventless reaction. In all cases, linear hydrocarbons such as n-paraffins, α-olefins and α,ω-dienes were detected. Increasing the decalin/plastic ratio led to enhanced α-olefin and n-paraffins yields, but the increase was more significant in the case of α-olefins, which are valuable compounds useful as raw chemicals. A reaction mechanism was proposed to explain the results obtained in presence of decalin. In these reactions, intramolecular radical transfer, secondary radical β-scission and hydrogen transfer from both decalin to intermediate radicals and from the polymer chain to regenerate the decalin play a significant role in determining the plastic conversion and the relative amounts of each product.     

Speciation and quantitation of degradation products of silicones (Silane/Siloxane Diols) by gas chromatography—mass spectrometry and stability of dimethylsilanediol

Gas chromatography-mass spectrometry (GC-MS) methodology was developed to speciate and quantitate several degradation products of polydimethylsiloxane (PDMS) in soil. We have demonstrated that the major degradation product,viz., dimethylsilanediol, can be readily analyzed by GC-MS without derivatization as commonly practiced in analyzing such materials. A mixture of linear siloxane diols (n = 1–5, wheren is the number of Me₂SiO units), and cyclic dimethylsiloxanes (n = 4–6) was resolved by GC-MS. We also found that peak identity of various diols required that GC-MS is done in the chemical ionization (CI) mode, since the electron impact (EI) ionization mode produced similar mass fragmentation patterns for diols and cyclics containing the same number of silicon atoms. For siloxane diols, detection limits ranged from 100 pg (forn = 1) to 1 ng (for n = 5). For cyclics, the detection limit was about 1 pg. Dimethylsilanediol, known to be unstable even in the solid state, was shown by NMR techniques to be stable in aqueous solution at <0.1% concentration. A 100-ppm solution was stable for over a year. Purity check for dimethylsilanediol is best carried out by Si-29 solid-state NMR technique.     

Processing and mechanical properties of biodegradable Poly(hydroxybutyrate-co-valerate)-starch compositions

Poly(hydroxybutyrate-co-valerate) (PHBV) is a completely biodegradable thermoplastic polyester produced by microbial fermentation. The current market price of PHBV is significantly higher than that of commodity plastics such as polyethylene and polystyrene. It is therefore desirable to develop low-cost PHBV based materials to improve market opportunities for PHBV. We have produced low-cost environmentally compatible materials by blending PHBV with granular starch and environmentally benign CaCO₃. Such materials can be used for specific applications where product biodegradability is a key factor and where certain mechanical properties can be compromised at the expense of lower cost. The inclusion of granular starch (25 wt%) and CaCO₃ (10 wt%) in a PHBV matrix (8% HV, 5% plasticizer) reduces the cost by approximately 40% and has a tensile strength of 16 MPa and flexural modulus of 2.0 Gpa, while the unfilled PHBV/plasticizer matrix has a tensile strength of 27 MPa and a flexural modulus of 1.6 GPa.Paper presented at the Bio/Environmentally Degradable Polymer Society—Third National Meeting, June 6–8, 1994, Boston, Massachusetts.The mention of firm names or trade products does not imply that they are endorsed or recommended by the U.S. Department of Agriculture over other firms or similar products not mentioned.     

Distribution of inorganic bromine and metals during co-combustion of polycarbonate (BrPC) and high-impact polystyrene (BrHIPS) wastes containing brominated flame retardants (BFRs) with metallurgical dust

This study focused on the thermal degradation of polycarbonate (BrPC) and high-impact polystyrene (BrHIPS), containing different brominated flame retardants. The evolved inorganic bromine was utilized for the separation of metals present in electric arc furnace dust (EAFD). The thermal degradation of BrPC generated inorganic gaseous HBr (69%) and condensable Br₂ (31%). The bromine evolved from BrHIPS was detected almost entirely in a condensed phase as SbBr₃. When mixed with EAFD, the evolved inorganic bromine reacted immediately with the metallic components of zinc and lead, but not with iron. The best bromination efficiencies were obtained during the isothermal heating (80 min at 550 °C) of the mixtures at mass ratios of 6:1 and 9:1 w/w under oxidizing conditions. The achieved brominating rates reached 78 and 81% for zinc and 90 and 94% for lead in 6:1 and 9:1 BrPC:EAFD, respectively, and 47 and 65% for zinc and 67 and 63% for lead in 6:1 and 9:1 BrHIPS:EAFD, respectively. The oxidizing condition favored complete vaporization of the formed bromides.     

Poly(hydroxyalkanoate) Biosynthesis from Crude Alaskan Pollock (Theragra chalcogramma) Oil

Six strains of Pseudomonas were tested for their abilities to synthesize poly(hydroxyalkanoate) (PHA) polymers from crude Pollock oil, a large volume byproduct of the Alaskan fishing industry. All six strains were found to produce PHA polymers from hydrolyzed Pollock oil with productivities (P; the percent of the cell mass that is polymer) ranging from 6 to 53% of the cell dry weight (CDW). Two strains, P. oleovorans NRRL B-778 (P = 27%) and P. oleovorans NRRL B-14682 (P = 6%), synthesized poly(3-hydroxybutyrate) (PHB) with number average molecular weights (M_n) of 206,000 g/mol and 195,000 g/mol, respectively. Four strains, P. oleovorans NRRL B-14683 (P = 52%), P. resinovorans NRRL B-2649 (P = 53%), P. corrugata 388 (P = 43%), and P. putida KT2442 (P = 39%), synthesized medium-chain-length PHA (mcl-PHA) polymers with M_n values ranging from 84,000 g/mol to 153,000 g/mol. All mcl-PHA polymers were primarily composed of 3-hydroxyoctanoic acid (C_8:0) and 3-hydroxydecanoic acid (C_10:0) amounting to at least 75% of the total monomers present. Unsaturated monomers were also present in the mcl-PHA polymers at concentrations between 13% and 16%, providing loci for polymer derivatization and/or crosslinking. Mention of trade names or commercial products in this article is solely for the purpose of providing specific information and does not imply recommendation or endorsement by the U.S. Department of Agriculture.     

Influence of zinc chloride addition on the chemical structure of bio-oil obtained during co-pyrolysis of wood/synthetic polymer blends

The chemical structure of liquid products of the pinewood sawdust (W) co-pyrolysis with polystyrene (PS) and polypropylene (PP) with and without the zinc chloride as an additive was investigated. The pyrolysis process was carried out at 450 °C with the heating rate of 5 °C/min. The yield of liquid products of pyrolysis was in the range of 37–91 wt% and their form was liquid or semi-solid depending on the composition of the wood/polymer blend. The zinc chloride addition to wood/polymer blends has influenced the range of samples decomposition as well as the chemical structure of resulted bio-oils. All bio-oils from wood/polypropylene blends were two-phase (liquid and solid). Contrarily, all bio-oils obtained from biopolymer/polypropylene blends with zinc chloride added were yellow liquids. All analyses proved that the structure and the quality of bio-oil strongly depend on both the composition of the blend and the presence of ZnCl₂ as an additive. The FT-IR analyses of oils showed that oxygen-containing groups and hydrocarbons content highly depend on the composition of biomass/synthetic polymer mixture. The fractionation of bio-oils by column chromatography with four different solvents was followed by GC–MS analysis. Results confirmed the significant removal and/or transformation of oxygen-containing organic compounds due to the zinc chloride presence during pyrolysis process.     

Production of hydrogen by steam gasification of dehydrochlorinated poly(vinyl chloride) or activated carbon in the presence of various alkali compounds

Steam gasification of dehydrochlorinated poly(vinyl chloride) (PVC) or activated carbon was carried out in the presence of various alkali compounds at 3.0 MPa and 560°C–660°C in a batch reactor or in a semi-batch reactor with a flow of nitrogen and steam. Hydrogen and sodium carbonate were the main products, and methane and carbon dioxide were the minor products. Yields of hydrogen were high in the presence of sodium hydroxide and potassium hydroxide. The acceleration effect of the alkali compounds on the gasification reaction was as follows: KOH > NaOH > Ca(OH)₂ > Na₂CO₃. The rate of gasification increased with increasing partial steam pressure and NaOH/C molar ratio. However, the rate became saturated at a molar ratio of NaOH/C greater than 2.0.     

Identification,Abundance and Origin of Aliphatic Hydrocarbons in the Fine Atmospheric Particulate Matter of Athens,Greece

The organic chemical composition of the fine fraction of atmospheric particulate matter in Athens has been studied, in order to establish emission sources. The results of the analyses of the aliphatic fraction indicate that all samples contain n-alkanes ranging from C₁₄ to C₃₂, with C₂₅, C₂₆, C₂₇ and C₂₉ being the more abundant congeners. Fossil fuels biomarkers such as extended tricyclic terpanes (hopanes, steranes) and isoprenoid hydrocarbons (pristane, phytane) were observed in our samples on a daily basis. Source reconciliation was conducted using molecular diagnostic ratios (such as the carbon preference index – CPI). The mean CPI value (1.84) indicates the mixed origin of the Athenian fine particles. The notable presence of an unresolved complex mixture or “hump” of hydrocarbons in our gas chromatograms is indicative of petrogenic hydrocarbon inputs. An approximate measure of this kind of contamination is the ratio of the concentrations of unresolved components to the resolved n-alkanes and other major compounds (U:R). The high U:R value of 25.25 further confirmed the major contribution of fossil fuels. Yet, the percent contribution of leaf wax n-alkanes (25.15%) indicated the parallel contribution of biogenic sources. This work supports the conclusion that vehicular emissions were the major source of aliphatic organic compounds with a smaller contribution of biogenic n-alkanes during the study period in Athens.     

Properties and biodegradability of chain-extended copoly(succinic anhydride/ethylene oxide)

Chain-extension reactions were carried out using titanium-iso-propoxide (TIP) as a catalyst for a series of polyesters or copolyesterethers with low molecular weights (M _n =1500–10,000) synthesized by the ring-opening copolymerization of succinic anhydride (SA) with ethylene oxide (EO). The copolymers having aM _n from 25,000 to 50,000 of different properties were obtained. Both the melting point (T _m ) and the fusion heat (H), which indicate the crystallinity of the copolymers, rose with an increase in SA content in the copolymers. Semitransparent films were prepared by compression molding of the copolymers. The biodegradation of the copolymer films was evaluated by enzymatic hydrolysis by lipases and by an aerobic gas evolution test in standard activated sludge. The hydrolyzability of these copolymers by three kinds of lipases was affected by their copolymer composition SA/EO, form, andM _n . The copolyesterether (SA/EO=43/57,M _n =48,900) was more easily biodegraded by standard activated sludge compared to the polyester (SA/EO=47/53,M _n =36,300).Presented at the Pacifichem-95, December 17–22, 1995, Honolulu, Hawaii.     

Connectivity of Hybrid Polymer by Tight Binding Approximation: Example of (Si(CH3)2) n (OSiO) p (OH) q

We computed by a tight binding calculation taking into account hybridization, the total electronic energy of different connectivities (amorphous, fractal and linear) of (Si−(CH₃)₂) _n −(OSiO) _p (OH) _q . We found that the total electronic energy of the amorphous connectivity was the smallest as a function of the number of atoms contained by the hybrid polymer. As the total electronic energy is linked to the stability, we may say that the connectivity of such hybrid polymer has the highest stability for the amorphous connectivity.     

Synthesis of a block copolymer of poly(3-hydroxybutyrate) and poly(ethylene glycol) and its application to biodegradable polymer blends

A block copolymer {P[(R,S)-HB-b-EG]} of atactic poly[(R,S)-3-hydroxybutyrate] {P[(R,S)-HB]} and poly(ethylene glycol) (PEG) was prepared by the ring-opening polymerization of -butyrolactone in the presence of a macroinitiator (PEG/ZnEt₂/H₂O) which had been produced by the reaction of ,-dihydroxy PEG ( _n=3000) with ZnEt₂/H₂O (1/0.6) catalyst. The block copolymer ( _n=10,500, _w/ _n=1.2) was an A-B-A triblock copolymer comprising atactic P[(R,S)-HB] (A) and PEG (B) segments. The miscibility, physical properties, and biodegradability of binary blends of microbial poly[(R)-3-hydroxybutyrate] {P[(R)-HB]} with the block copolymer P[(R,S)-HB-b-EG] has been studied. The glass-transition temperature (T _g) data showed that the P[(R)-HB]/P[(R,S)-HB-b-EG] blend was miscible in the amorphous state. The P[(R)-HB] film became flexible and tough by means of blending with P[(R,S)-HB-b-EG] block copolymer. The enzymatic degradation of blend films was carried out at 37°C and pH 7.4 in a 0.1M phosphate solution of an extracellular PHB depolymerase fromAlcaligenes faecalis. The enzymatic degradation took place solely on the surface of the blend films.     

Combustion and inorganic bromine emission of waste printed circuit boards in a high temperature furnace

High temperature combustion experiments of waste printed circuit boards (PCBs) were conducted using a lab-scale system featuring a continuously-fed drop tube furnace. Combustion efficiency and the occurrence of inorganic bromine (HBr and Br₂) were systematically studied by monitoring the main combustion products continuously. The influence of furnace temperature (T) was studied from 800 to 1400 °C, the excess air factor (EAF) was varied from 1.2 to 1.9 and the residence time in the high temperature zone (RT_HT) was set at 0.25, 0.5, or 0.75 s.Combustion efficiency depends on temperature, EAF and RT_HT; temperature has the most significant effect. Conversion of organic bromine from flame retardants into HBr and Br₂ depends on temperature and EAF. Temperature has crucial influence over the ratio of HBr to Br₂, whereas oxygen partial pressure plays a minor role. The two forms of inorganic bromine seem substantially to reach thermodynamic equilibrium within 0.25 s. High temperature is required to improve the combustion performance: at 1200 °C or higher, an EAF of 1.3 or more, and a RT_HT exceeding 0.75 s, combustion is quite complete, the CO concentration in flue gas and remained carbon in ash are sufficiently low, and organobrominated compounds are successfully decomposed (more than 99.9%).According to these results, incineration of waste PCBs without preliminary separation and without additives would perform very well under certain conditions; the potential precursors for brominated dioxins formation could be destroyed efficiently. Increasing temperature could decrease the volume percentage ratio of Br₂/HBr in flue gas greatly.     

Effect of Poly(dioxolane) as Compatibilizer in Poly(ɛ-caprolactone)/Tapioca Starch Blends

The influence of poly(dioxolane) (PDXL), a poly(ethylene oxide-alt-methylene oxide), as compatibilizer on poly(ɛ-caprolactone) (PCL)/tapioca starch (TS) blends was studied. In order to facilitate blending; PCL, PDXL and TS must be blended together directly; so that PDXL is partially adhered at the TS surface as shown by scanning electron microscopy. The molecular weight effect of PDXL on the PCL/TS blends showed that mechanical properties of PCL/TS/PDXL blends from low molecular weight (M _n=10,000) and high molecular weight (M _n=200,000) PDXL were rather dependent on TS content. The enzymatic degradability of PCL/TS/PDXL blends using α-amylase increased as the TS content increased but was independent on the dispersion of tapioca starch in the PCL matrix.