Social trends of the people of the region of Eastern Macedonia and Thrace-Greece: about the potential of using biofuels from forest products residues

In the framework of enquiry of biomass usage possibilities in our country, a research was made through the whole Eastern Macedonia region, related to disposal possibilities from the production conveyors and usage possibilities from the region’s residents and businessmen, of biofuels that come from mechanical wood treatment residues and from the residues of agricultural production, in wooden form, known with the term wood pellets or wood briquettes. From the present study, it came to light that there is an intense interest for direct personal usage and application of biomass for the residents or occupational spaces heating. The necessary biomass quantity for the entire region’s households is estimated up to 205,520 t. From the biomass usage as a combustible material, a 680 €/year and household about, is made. The potential investments that will be made to the region seem to have a very short depreciation, but a business plan and a marketing plan syntax are considered as necessary for the result’s maximisation.     

Two-Phase Transport Model for the Pyrolysis Process of a Vertical Wood Cylinder,Including the Surrounding Flow Field

This paper describes a mathematical model for the pyrolysis of a small dry pine wood cylinder. The computational domain is axisymmetric and involves the heating chamber, with the wood cylinder vertically situated in the centre of the chamber. The model simulates the laminar flow around the particle and the laminar flow inside the wood/char matrix by applying a two-phase transport model where the solid wood/char matrix acts as one phase and the various gases produced from the pyrolysis process is assembled in the other phase.

Convective, conductive and thermal radiation transfer modes are included in the model. A two-step pyrolysis reaction scheme is used for the modelling of the conversion from wood to tar and gas. Both the thermal conductivity and the permeability of the wood/char matrix are modelled anisotropically in order to capture the directional differences in heat and mass transport, existing in real wood.

Results from simulations are compared with measurements from literature for the centre core solid temperature and the conversion from wood to char, tar and pyrolysis gas in the particle during heating. The results show very good agreement with the measured temperature profile. The simulated conversion profile shows an overall good agreement with the measurements, however with discrepancies in the early stage of the process. Besides the successful validation with the experimental data, it provides us with all the details of the distribution of the migrating pyrolysis gas and tar, the temperature, the velocity flow field and pressure in the wood/char cylinder.     

Perceptions, attitudes and interest of Swedish architects towards the use of wood frames in multi-storey buildings

Use of wood frames from sustainable forestry instead of non-wood frames in multi-storey buildings can reduce primary energy use and carbon dioxide emissions in construction. However, construction actors might have different perceptions towards wood frames than towards steel and concrete frames. Such perceptions may influence the actors’ decision to adopt wood frames. In this study we use a web-based questionnaire to assess Swedish architects’ perceptions, attitudes and interest towards steel, concrete and wood frames in multi-storey buildings (n = 412). Results indicate that the responding architects find concrete the most suitable frame material in buildings of 3-8 storeys, mainly because of the performance of concrete with regards to the engineering aspects (e.g. stability and fire safety) that were considered important in the choice of frame material. Although wood is considered the least suitable frame material, the overall attitude towards, and interest in, using wood is positive and related to the perceived environmental benefits of wood. This may derive from an increased discussion of and information about the environmental impact of buildings. Wood may be perceived as new and innovative while not considered as adequately proven as steel and concrete with regards to engineering aspects.     

Effects of increased wood energy consumption on carbon storage in forests of the United States

Large but feasible increases that have been projected for the production of wood energy in the United States can be expected to significantly alter the current carbon storage patterns in US forest vegetation. The 1976 net wood increment left after forest cutting equals about 136 × 10⁶ tons of carbon/year, with about 60% of the increment found in merchantable trees, and the remainder in nonmerchantable components.Achieving 5–10 quads of wood energy beyond 1976 levels by the year 2010 can significantly change current carbon storage patterns with the magnitude of change dependent on the extent of residue harvest to meet energy goals, and the rate of future forest growth. Complete loss of the apparent net wood increment is a possible outcome.Although the future growth and harvest situation cannot be known now, a range of possible scenarios suggests that US forests in the year 2010 will store much less carbon than today, thus significantly changing their role in the global carbon cycle.     

Drying of granulated wood ash by flue gas from saw dust and natural gas combustion

At the district heating plant of Kalmar, Sweden an on-line unit for production of granulated wood ash for nutrient recycling on forest soils is being applied. Currently, the granules are dried by hot air from an oil-fired burner. The objective of this work was to investigate how drying by flue gas affects the hardening of granules, or impacts their chemical composition and properties. Ninety-six granule samples were treated by flue gas from natural gas combustion in a laboratory pilot scale flue gas generator. CO₂, CO, O₂, C₃H₈ and NO concentrations were varied during the experiment. Additionally, some samples were treated by flue gas from combustion of sawdust at the heating plant in Kalmar. Drying by flue gases did not affect the chemical composition of granules, but minor effects were seen in their mineralogy. The carbonate content was slightly higher in granules treated with flue gas from natural gas combustion compared to the granules dried by hot air only, when measured by wet chemical methods. Results from XRD analysis imply that the calcite content is higher and the portlandite and arcanite content slightly less in granules treated with flue gas from sawdust combustion compared to the granules dried by hot air only. The results from this investigation showed no negative effects on ash granule composition or physical structure by the use of a flue as a drying medium.     

Energy and carbon balances of wood cascade chains

In this study we analyze the energy and carbon balances of various cascade chains for recovered wood lumber. Post-recovery options include reuse as lumber, reprocessing as particleboard, pulping to form paper products, and burning for energy recovery. We compare energy and carbon balances of chains of cascaded products to the balances of products obtained from virgin wood fiber or from non-wood material. We describe and quantify several mechanisms through which cascading can affect the energy and carbon balances: direct cascade effects due to different properties and logistics of virgin and recovered materials, substitution effects due to the reduced demand for non-wood materials when wood is cascaded, and land use effects due to alternative possible land uses when less timber harvest is needed because of wood cascading. In some analyses we assume the forest is a limiting resource, and in others we include a fixed amount of forest land from which biomass can be harvested for use as material or biofuel. Energy and carbon balances take into account manufacturing processes, recovery and transportation energy, material recovery losses, and forest processes. We find that land use effects have the greatest impact on energy and carbon balances, followed by substitution effects, while direct cascade effects are relatively minor.     

Evaluating the efficacy of wood shreds for mitigating erosion

An erosion control product made by shredding on-site woody materials was evaluated for mitigating erosion through a series of rainfall simulations. Tests were conducted on bare soil and soil with 30, 50, and 70% cover on a coarse and a fine-grained soil. Results indicated that the wood product known as wood shreds reduced runoff and soil loss from both soil types. Erosion mitigation ranged from 60 to nearly 100% depending on the soil type and amount of concentrated flow and wood shred cover. Wood shreds appear to be a viable alternative to agricultural straw. A wood shred cover of 50% appears optimal, but the appropriate coverage rate will depend on the amount of expected concentrated flow and soil type.     

Wood carbon content of tree species in Eastern China: interspecific variability and the importance of the volatile fraction

Data on the mass density and carbon content of tree organs, and in particular stem wood, are essential for accurate assessments of forest carbon sequestration. However most available data, including that for East Asia, has neglected the volatile C fraction. Wood samples were collected and assayed for C content from 14 native tree species in Jilin Province, NE China. C content showed statistically significant variation among species, ranging from 48.4% to 51.0%. The volatile C fraction was non-negligible, averaging 2.2%, and showed high variation among species. As found in prior studies, wood C content was appreciably higher in conifer than hardwood (angiosperm) species (50.8+/-0.1% vs. 49.5+/-0.2%, respectively). Wood carbon density (gC/cm(3)) showed very high inter-specific variation, due mainly to differences in wood specific gravity. Our analyses, in conjunction with recently published data from North America, indicate a global mean value of 47.5+/-0.5% wood C content exclusive of volatile C; the widely used 50% figure corresponds more closely to total wood C inclusive of the volatile fraction. Failure to include volatile C or to use species- or higher-taxon-specific C content values in forest C assessments is likely to introduce biases on the order approximately 4-6%. In addition, the stocks and flows of the volatile C fraction in wood are in themselves an important and sorely neglected aspect of forest C processes likely to be strongly impacted by harvests and other management practices.     

Rehabilitating Agricultural Streams in Australia with Wood: A Review

Worldwide, the ecological condition of streams and rivers has been impaired by agricultural practices such as broadscale modification of catchments, high nutrient and sediment inputs, loss of riparian vegetation, and altered hydrology. Typical responses include channel incision, excessive sedimentation, declining water quality, and loss of in-stream habitat complexity and biodiversity. We review these impacts, focusing on the potential benefits and limitations of wood reintroduction as a transitional rehabilitation technique in these agricultural landscapes using Australian examples. In streams, wood plays key roles in shaping velocity and sedimentation profiles, forming pools, and strengthening banks. In the simplified channels typical of many agricultural streams, wood provides habitat for fauna, substrate for biofilms, and refuge from predators and flow extremes, and enhances in-stream diversity of fish and macroinvertebrates.Most previous restoration studies involving wood reintroduction have been in forested landscapes, but some results might be extrapolated to agricultural streams. In these studies, wood enhanced diversity of fish and macroinvertebrates, increased storage of organic material and sediment, and improved bed and bank stability. Failure to meet restoration objectives appeared most likely where channel incision was severe and in highly degraded environments. Methods for wood reintroduction have logistical advantages over many other restoration techniques, being relatively low cost and low maintenance. Wood reintroduction is a viable transitional restoration technique for agricultural landscapes likely to rapidly improve stream condition if sources of colonists are viable and water quality is suitable.     

Importance of landscape heterogeneity to wood storks in Florida Everglades

Declines in populations of and reproductive success of wood storks and other wading birds have occurred in the Florida Everglades over the past several decades. These declines have been concurrent with major changes in the Everglades’ landscape characteristics. Among the plausible hypotheses that relate to landscape change are the following: (1) general loss of habitat; (2) heavy loss of specific habitat, namely, short-hydroperiod wetlands that provide high prey availability early in the breeding season; and (3) an increase in frequency of major drying out of the central slough areas, which can affect prey availability late in the breeding season. These three hypotheses were compared using an individual-based model of wood stork (Mycteria americana) reproduction. This model simulated the behavior and energetics of each individual wood stork in a breeding colony on 15-min time intervals. Changes in water depth and prey availability occurred on daily time steps. Simulation results showed a threshold response in reproductive success to reduction of wetland heterogeneity. Model comparisons in which (1) only short-hydroperiod wetlands were removed and (2) wetlands of both long and short hydroperiods were removed showed that, for the same loss of total area, the specific habitat removal caused a much greater reduction in wood stork reproduction, indicating hypothesis 2 may be a more likely explanation than hypothesis 1. Reduction of initial prey availability in the central slough areas (simulating frequent drying; hypothesis 3) reduced fledging success by an average of more than 90% in the model.     

Influences on Wood Load in Mountain Streams of the Bighorn National Forest,Wyoming, USA

We documented valley and channel characteristics and wood loads in 19 reaches of forested headwater mountain streams in the Bighorn National Forest of northern Wyoming. Ten of these reaches were in the Upper Tongue River watershed, which has a history of management including timber harvest, tie floating, and road construction. Nine reaches were in the North Rock Creek watershed, which has little history of management activities. We used these data to test hypotheses that (i) valley geometry correlates with wood load, (ii) stream gradient correlates with wood load, and (iii) wood loads are significantly lower in managed watersheds than in otherwise similar unmanaged watersheds. Statistical analyses of the data support the first and third hypotheses. Stream reaches with steeper valley side slopes tend to have higher wood loads, and reaches in managed watersheds tend to have lower wood loads than reaches in unmanaged watersheds. Results do not support the second hypothesis. Shear stress correlated more strongly with wood load than did stream gradient, but statistical models with valley-scale variables had greater explanatory power than statistical models with channel-scale variables. Wood loads in stream reaches within managed watersheds in the Bighorn National Forest tend to be two to three times lower than wood loads in unmanaged watersheds.     

An exploratory assessment of the attitudes of Chinese wood products manufacturers towards forest certification

Interviews with Chinese forest products manufacturers were conducted to explore their attitudes towards forest certification and related issues. Participants comprised owners, CEOs, and managers in 20 Chinese wood products companies, including producers of furniture, doors, flooring, and various engineered wood products. The interviews were used to analyze the extent to which participants were considering adopting forest certification and what might motivate such a decision. This was done by assessing their awareness and knowledge of certification. The results indicated that participants' understanding of forest certification was extremely low, despite major efforts in China to raise awareness of the issue. Potential economic benefits were the most frequently cited reason to adopt certification, including gaining or maintaining competitive advantage over their industry counterparts, improved access to both domestic and export markets, better customer recognition, and enhanced corporate responsibility practices. Some interviewees (3 out of 20) considered that certification would become a mandatory requirement or industry standard, and that this would be the only viable motivation for certification given that the financial benefits were potentially limited. According to the participants, the main differences between certified and uncertified wood products operations related to improved market access and public image. Interviewees felt that cooperation between and support from governments and the forest industry would enable the enhanced awareness of certification amongst manufacturers and the general public. This, in turn, could serve to stimulate demand for certified products.     

Methanogenic toxicity and continuous anaerobic treatment of wood processing effluents

Wood processing effluents contain different types of phenolic compounds, from simple monomers to high molecular weight (MW) polyphenolic polymers, that can inhibit wastewater treatment. This work presents a comparative study of the methanogenic toxicity produced by three wood processing effluents (hardboard, fiberboard and BKME (kraft mill effluent)) using Pinus radiata, Eucalyptus and Tepa as feedstock (the last one being a native Chilean tree species). This study evaluates the influence of non-adapted granular and adapted flocculent sludge on forest industrial wastewater treatment as well as continuous anaerobic biodegradation of hardboard processing effluent using the upflow anaerobic sludge blanket (UASB). The adapted biomass (flocculent sludge) did not show any lag-phase signs. The 50% IC (the concentration causing 50% inhibition of methanogenic activity) was 4.3 g COD-effluent (chemical oxygen demand (COD)-of the effluent)/l and 2.8 g COD-effluent/l for the flocculent sludge and the granular sludge, respectively. The UASB system worked at low organic load rates (0.1-0.4 g COD/l d) with the COD removal ranging between 10 and 30%, and color removal did not occur under anaerobic conditions due to high MW. Indeed, the MW analysis indicates the presence of phenolic compounds over 25,000 Da in the anaerobic effluent.     

A Heat Dynamic Model for Intelligent Heating of Buildings

This article presents a heat dynamic model for prediction of the indoor temperature in an office building. The model has been used in several flexible load applications, where the indoor temperature is allowed to vary around a given reference to provide power system services by shifting the heating of the building in time. This way the thermal mass of the building can be used to absorb energy from renewable energy source when available and postpone heating in periods with lack of renewable energy generation. The model is used in a model predictive controller to ensure the residential comfort over a given prediction horizon.     

The implementation of wood waste ash as a partial cement replacement material in the production of structural grade concrete and mortar: An overview

The timber manufacturing and power generation industry is gradually shifting towards the use of biomass such as timber processing waste for fuel and energy production and to help supplement the electrical energy demand of national electric gridlines. Though timber processing waste is a sustainable and renewable source of fuel for energy production, the thermal process of converting the aforementioned biomass into heat energy produces significant amounts of fine wood waste ash as a by-product material which, if not managed properly, may result in serious environmental and health problems. Several current researches had been carried out to incorporate wood waste ash as a cement replacement material in the production of greener concrete material and also as a sustainable means of disposal for wood waste ash. Results of the researches have indicated that wood waste ash can be effectively used as a cement replacement material for the production of structural grade concrete of acceptable strength and durability performances. This paper presents an overview of the work carried out by the use of wood waste ash as a partial replacement of cement in mortar and concrete mixes. Several aspects such as the physical and chemical properties of wood waste ash, properties of wood waste ash/OPC blended cement pastes, rheological, mechanical and the durability properties of wood waste ash/OPC concrete mix are detailed in this paper.     

Managing Plantation Forests to Provide Short- to Long-Term Supplies of Wood to Streams: A Simulation Study Using New Zealand’s Pine Plantations

Riparian functions such as the recruitment of wood to streams take decades to recover after a clear-fell harvest to the stream edge. The implications of two sets of riparian management scenarios on the short- and long-term recruitment of wood to a hypothetical stream (central North Island, New Zealand) were compared through simulation modeling. In the first set (native forest buffer), a designated treeless riparian buffer was colonized by native forest species after a pine crop (Pinus radiata) had been harvested to the stream bank. In the second set (pine to native forest buffer), native forest species were allowed to establish under the pine canopy in a designated riparian buffer. In general, the volume of wood was greater in streams with wider buffers (5-m to 50-m) and this effect increased with forest age (800 years). The pine to native forest buffer supplied more wood to the stream more quickly, and matched the long-term supply to the stream from the native forest buffer. For the native forest buffer, total wood volume was minimal for the first 70 years and then increased uniformly for the remainder of the simulation. In contrast, the pine to native forest buffer produced a bimodal response in total wood volume with the initial sharp peak at year 100 attributed to pine recruitment and a second more gradual peak lasting for the rest of the simulation, which was similar to levels in the native forest simulations. These results suggest that existing plantations could be an important source of wood to the stream during the first 100+ years of native forest development.     

Controlling urban air pollution caused by households: uncertainty, prices, and income

We examine the control of air pollution caused by households burning wood for heating and cooking in the developing world. Since the problem is one of controlling emissions from nonpoint sources, regulations are likely to be directed at household choices of wood consumption and combustion technologies. Moreover, these choices are subtractions from, or contributions to, the pure public good of air quality. Consequently, the efficient policy design is not independent of the distribution of household income. Since it is unrealistic to assume that environmental authorities can make lump sum income transfers part of control policies, efficient control of air pollution caused by wood consumption entails a higher tax on wood consumption and a higher subsidy for more efficient combustion technologies for higher income households. Among other difficulties, implementing a policy to promote the adoption of cleaner combustion technologies must overcome the seemingly paradoxical result that efficient control calls for higher technology subsidies for higher income households.     

Determining residential firewood consumption

Household firewood use has become increasingly popular in the United States over the past few years. Significant problems remain in estimating firewood consumption. Methods of determining the amount of wood consumed vary from state to state. Units used for measuring firewood vary, but the cord remains the researcher's favorite. Factors used for converting other units, such as pickup truck loads to cords also vary. People who do not use firewood are less likely to respond to mailed surveys, resulting in potential overestimates of statewide consumption. This paper identifies some problems associated with estimating household firewood consumption and recommends methods of dealing with them.     

Comparing the effectiveness of education and technology in reducing wood smoke pollution: A field experiment

This study describes a field experiment assessing the effectiveness of education and technological innovation in reducing air pollution generated by domestic wood heaters. Two-hundred and twenty four households from a small regional center in Australia were randomly assigned to one of four experimental conditions: (1) Education only – households received a wood smoke reduction education pack containing information about the negative health impacts of wood smoke pollution, and advice about wood heater operation and firewood management; (2) SmartBurn only – households received a SmartBurn canister designed to improve combustion and help wood fires burn more efficiently, (3) Education and SmartBurn, and (4) neither Education nor SmartBurn (control). Analysis of covariance, controlling for pre-intervention household wood smoke emissions, wood moisture content, and wood heater age, revealed that education and SmartBurn were both associated with significant reduction in wood smoke emissions during the post-intervention period. Follow-up mediation analyses indicated that education reduced emissions by improving wood heater operation practices, but not by increasing health risk perceptions. As predicted, SmartBurn exerted a direct effect on emission levels, unmediated by wood heater operation practices or health risk perceptions.     

Biomass as the Renewable Energy Sources in Malaysia: An Overview

Past and current economic growths of Malaysia have been primarily energized by fossil fuels. Malaysia has very substantial potential for biomass energy utilization given its equatorial climate that is ideal for dense tropical forest growth and agricultural vegetation. There are five major sectors contributing wastes to biomass energy in Malaysia: forestry (wood products), rubber cultivation, cocoa cultivation, sugar cane cultivation and oil palm cultivation. Biomass in Malaysia contributes about 14% of the approximately 340 million barrel of oil equivalent (boe) of energy used every year. This paper provides an overview on the types of biomass being used, the research works on biomass conversion into energy and the present biomass energy projects in Malaysia.