Hazardous substances in indoor dust emitted from waste TV recycling facility

Various hazardous substances contained in waste TV sets might be released into environment via dust during recycling activities. Two brominated flame retardants (BFRs), polybrominated diphenyl ethers (PBDEs), and tetrabromobisphenol A (TBBPA), and five kinds of heavy metals (Cu, Pb, Cd, Cr, and Ni) were detected in indoor dust collected from two workshops (TV dismantling workshop and subsequent recycling workshop). PBDEs concentrations in dust from waste wires recycling line (722,000 ng/g) were the highest among the studied sites, followed by those in manual dismantling–sorting line (117,000 ng/g), whereas TBBPA concentrations were the highest in manual dismantling–sorting line (557 ng/g) and printed circuit board (PCB) recycling line (428 ng/g). For heavy metals, Cu and Pb were the most enriched metals in all dust samples. The highest concentration of Pb (22,900 mg/kg) was found in TV dismantling workshop-floor dust. Meanwhile, Cu was the predominant metal in dust from the PCB recycling line, especially in dust collected from electrostatic separation area (42,700 mg/kg). Occupational exposure assessment results showed that workers were the most exposed to BDE-209 among the four PBDE congeners (BDE-47, BDE-99, BDE-153, and BDE-209) in both workshops. The hazard quotient (HQ) indicated that noncancerous effects were unlikely for both BFRs and heavy metals (HQ?<?1), and carcinogenic risks for Cd, Cr, and Ni (risk?<?10^?6) on workers in two workshops were relatively low.     

Trace metals, anions and polybromodiphenyl ethers in settled indoor dust and their association

Contaminants in settled indoor dust are potentially health hazardous to human. Thus, identification and quantification of toxic chemicals in settled indoor dust is of great concern. In this study, the levels of major anions ( $ \mathrm{C}{{\mathrm{l}}^{-}},\mathrm{N}{{\mathrm{O}}_2}^{-},\mathrm{B}{{\mathrm{r}}^{-}},\mathrm{N}{{\mathrm{O}}_3}^{-},\mathrm{P}{{\mathrm{O}}_4}^{3-}\,\mathrm{and}\,\mathrm{S}{{\mathrm{O}}_4}^{2- } $ ), trace metals (Cr, Mn, Fe, Co, Ni, Cu, Zn, Cd, As and Pb) and polybromodiphenyl ethers (PBDEs) in settled office and home dust were determined and correlations between the contaminants investigated. Depending on the available materials in both microenvironments, the most possible sources were identified. The results showed that the settled office dusts (n?=?6 pooled samples from 85 offices) were more contaminated than home dusts (n?=?8 homes). For anions, $ \mathrm{S}{{\mathrm{O}}_4}^{2- } $ and Cl^– accounted for 87 and 97 % of the total office and home dust contaminants, respectively. For trace metals, Fe, Cu, Zn and Mn, accounted for 98 % of the contaminants in both office and home dust samples. Fe exhibited the highest percentage of 76.7 and 87.3 % in office and home dust samples, respectively. For PBDEs, the mean concentrations detected in office and home dust ranged between 5.8–86.3 and 1.5–20.6 ng?g^?1, respectively. The log-transformed correlation between the total concentrations of trace metals and major anions detected in offices and homes was positive for offices and negative for homes with a statistically significant values (r?=?0.73, p?<?0.01; r?= ?0.22, p?<?0.01, respectively). The daily exposure rates determined for the most hazardous such as As, Cd, Pb and PBDEs congeners, relative to the individual concentrations reported in the literature in settled indoor dust, were found very lower. Therefore, maybe it is possible to expect less potential health risk. Investigation of formation of coordination compounds between trace metals and PBDEs congeners is possible; however, this requires further study.     

Heavy metals exposure of children from stairway and sidewalk dust in the smelting district,northeast of China

The aim of this work was to study metals accumulation in stairway (inside the residential building) and sidewalk (outside the residential building) dust, and health risk of children due to dust exposure. The investigation included the: (a) spatial distributions of Hg, Pb, Cd, Zn and Cu in stairway and sidewalk dust, (b) source analysis of metals in stairway and sidewalk dust, and (c) assessment of the children health risks due to metals exposure from stairway and sidewalk dust. In the smelting district of Huludao, the maximum Hg, Pb, Cd, Zn and Cu contents in stairway dust were 5.324, 4594, 936.8, 48 253, 1377 mg kg^?1, respectively, and were 144, 213, 8674, 760 and 69.5 times as high, respectively, as the background values in soil. A strong positive relationship was shown between the stairway and sidewalk dust for each metal (p < 0.01). The trends for Hg, Pb, Cd, Zn and Cu in the stairway and sidewalk dust were similar and with higher concentrations trending Huludao Zinc Plant (HZP). Atmospheric deposition due to metal smelting from HZP was the common source of heavy metals in the sidewalk and stairway dust. Vehicular traffic affected the metal accumulation in dust, but their contribution was slight comparing with atmospheric emission from HZP. Almost all hazard indexes (HIs) for metals due to stairway dust exposure in this study were lower than 1. The health risk for children was low if they would not play in the stairway. However, children were also experiencing the potential health risk from Cd and Pb exposure from sidewalk dust outside residential building, especially near HZP.     

Polycyclic aromatic hydrocarbons and trace metals in mosque’s carpet dust of Riyadh,Saudi Arabia,and their health risk implications

The main objectives of this work were to identify and determine the concentrations of polycyclic aromatic hydrocarbons (PAHs) and trace metals in carpet dust samples from various mosques of the city of Riyadh and to assess the health risks associated with the exposure to these pollutants. Therefore, 31 samples of mosque’s carpet dust from Riyadh were collected. The results showed that 14 PAHs were present in the dust samples with concentrations ranged from 90 to 22,146 ng g^?1 (mean = 4096 ± 4277 ng g^?1) where low molecular weight compounds were dominant. The presence of PAHs were in the order of naphthalene > chrysene and benzo(b)fluoranthene > benzo(a)pyrene > acenaphthene and benzo(k)fluoranthene > pyrene and the absence of indeno(1,2,3-cd)pyrene and dibenz(a,h)anthracene. The diagnostic ratio coupled with principle component analysis (PCA) revealed mix sources of petrogenic from traffic, stack emission, and pyrogenic inputs from essence and perfumed wood burning. Trace metals were significant in the dust samples, and their concentrations decrease in the order of Zn, Mn, Cu, Cr, Pb, Ni, and V where Zn being the highest (94.4 ± 91.5 μg g^?1) and indium was the lowest (1.9 ± 9.3 μg g^?1). The trace metals were major in southern and central parts of Riyadh and followed the order of central Riyadh > southern Riyadh > western Riyadh > eastern Riyadh > northern Riyadh. Estimated risk based on the total PAHs was found to be 4.30 × 10^?11 for adult and 1.56 × 10^?11 for children. Elemental non-cancer risk for adults ranged from 7.9 × 10^?4 for Co to 7.58 × 10^?1 for Li and for children ranged from 3.70 × 10^?3 for Co to 3.54 for Li. Policy implication and mitigations of PAHs in Riyadh and Saudi Arabia were highlighted.     

Use of sedimentary metals to predict metal concentrations in black mussel (Mytilus galloprovincialis) tissue and risk to human health (Sydney estuary, Australia)

Filter-feeding bivalves have been used extensively as an indicator of ecosystem condition and in management of estuarine environments. The current study aimed to determine whether sedimentary metals could predict metal concentrations in tissue of filter-feeding mussels (Mytilus galloprovincialis) and to identify areas of the estuary where mussel consumption posed a human health risk. Mussel tissue Cu and Zn concentrations (wet weight) were below guideline values for human consumption in all parts of the waterway, whereas Pb tissue concentrations exceed these guidelines (2.0 μg?g^?1 wet weight) in the upper reaches of some embayments of the estuary. Concentrations of Cu and Pb in the fine fraction (<62.5 μm) of bottom sediment reasonably predicted concentrations (dry weight) of these metals in mussel tissue (r ²?=?0.460 and p?=?0.001 and r ²?=?0.669 and p?<?0.0001, respectively) as these materials are resuspendable and available to filter-feeding estuarine animals, whereas total sediment and mussel tissue were poorly related. Lead concentrations (>350 μg?g^?1) in fine sediments indicated areas of this estuary where human health was at risk due to high tissue concentrations of this metal. These results give encouragement for the use of the metal concentration in fine sediments as an indicator of estuarine condition and risk to human health in this waterway. Mussels were distributed in all parts of the estuary, even in areas where metal concentrations exceeded sediment quality guidelines.     

Lead,mercury, cadmium,chromium, nickel,copper, zinc,calcium, iron,manganese and chromium (VI) levels in Nigeria and United States of America cement dust

This study was aimed at investigating the relative abundance of heavy metals in cement dust from different cement dust factories in order to predict their possible roles in the severity of cement dust toxicity. The concentrations of total mercury (Hg), copper (Cu), chromium (Cr), cadmium (Cd), nickel (Ni), manganese (Mn), lead (Pb), iron (Fe) and chromium (VI) (Cr (VI)) levels in cement dust and clinker samples from Nigeria and cement dust sample from the United States of America (USA) were determined using graphite furnace atomic absorption (GFAAS), while Zn and Ca were measured by flame atomic absorption spectrophotometry (FAAS), and Cr (VI) by colorimetric method. Total Cu, Ni and Mn were significantly higher in cement dust sample from USA (p < 0.05), also, both total Cr and Cr (VI) were 5.4–26 folds higher in USA cement dust compared with Nigeria cement dust or clinker (p < 0.001). Total Cd was higher in both Nigeria cement dust and clinker (p < 0.05 and p < 0.001), respectively. Mercury was more in both Nigeria cement dust and clinker (p < 0.05), while Pb was only significantly higher in clinker from Nigeria (p < 0.001). These results show that cement dust contain mixture of metals that are known human carcinogens and also have been implicated in other debilitating health conditions. Additionally, it revealed that metal content concentrations are factory dependent. This study appears to indicate the need for additional human studies relating the toxicity of these metals and their health impacts on cement factory workers.     

Determination of Heavy Metals in Indoor Dust From Primary School (Sri Serdang,Malaysia): Estimation of the Health Risks

Heavy metal concentrations (Pb, Cd, and Cu) in classroom indoor dust were measured. The health risk (non-carcinogenic) of these heavy metals in classroom indoor dust to children was assessed based on United States Environmental Protection Agency health risk model. Indoor classroom dust samples were collected from 21 locations including windows, fans, and floors at a primary school in Sri Serdang, Malaysia. Classroom dust samples were processed using aqua regia method and analyzed for Pb, Cd, and Cu concentrations. The highest average heavy metal concentrations were found in windows, followed by floor and fan. Pb concentrations ranged from 34.17 μg/g to 101.87 μg/g, Cd concentrations ranged from 1.73 μg/g to 7.5 μg/g, and Cu concentrations ranged from 20.27 μg/g to 82.13 μg/g. Ventilation and cleaning process were found as the possible factors that contributed to heavy metal concentration in window, floor, and fan. Moreover, the hazard index (HI) and hazard quotient (HQ) values for heavy metals Cd and Cu were less than one. By contrast, the HI and HQ values for Pb (maximum values) were more than one, indicating potential non-carcinogenic risk to children. Long-term persistence of leaded petrol, building materials, interior paint, school located near industrial areas and major roads, as well as vehicle emission are the factors attributed to the presence of heavy metals in classroom dust. Further research under a long-term monitoring plan and actual values in a health risk model is crucial before a final decision on heavy metal exposure and its relationship to young children health risks can be made. Nevertheless, the findings of this study provide crucial evidence to include indoor dust quality in school assessment because the environmental processes and impacts of surrounding school area have health risk implications on young children.     

Distribution of polybrominated diphenyl ethers and dust particle size fractions adherent to skin in indoor dust,Pretoria, South Africa

In order to determine human exposure to the indoor toxicant, selection of dust fraction and understanding dust particle size distribution in settled indoor dust are very important. This study examined the influence of dust particle size on the concentration of polybrominated diphenyl ethers (PBDEs) congeners, assessed the distribution of dust particle size and characterized the main indoor emission sources of PBDEs. Accordingly, the concentrations of PBDE congeners determined in different indoor dust fractions were found to be relatively higher in the order of dust particle size: 45–106 μm?>?(<45 μm)?>?106–150 μm. The finding shows arbitrary selection of dust fractions for exposure determination may result in wrong conclusions. Statistically significant moderate correlation between the concentration of Σ₉PBDEs and organic matter content calculated with respect to the total dust mass was also observed (r?=?0.55, p?=?0.001). On average, of total dust particle size <250 μm, 93.4 % (m/m%) of dust fractions was associated with less than 150 μm. Furthermore, of skin adherent dust fractions considered (<150 μm), 86 % (v/v%) is in the range of particle size 9.25–104.7 μm. Electronic materials treated with PBDEs were found the main emission sources of PBDE congeners in indoor environment. Based on concentrations of PBDEs determined and mass of indoor dust observed, 150 μm metallic sieve is adequate for human exposure risk assessment. However, research in this area is very limited and more research is required to generalize the fact.     

Distribution,source, and environmental risk assessment of phthalate esters (PAEs) in water,suspended particulate matter,and sediment of a typical Yangtze River Delta City,China

Phthalates (PAEs) in drinking water sources such as the Yangtze River in developing countries had aroused widespread concern. Here, the water, suspended particulate matter (SPM), and sediment samples were collected from 15 sites in wet and dry seasons in Zhenjiang, for the determination of six PAEs (DMP, DEP, DIBP, DBP, DEHP, and DOP) using the solid-phase extraction (SPE) or ultrasonic extraction coupled with gas chromatography-mass spectrometry (GC-MS). The total concentrations of six PAEs (Σ₆PAEs) spanned a range of 2.65–39.31 μg L^?1 in water, 1.97–34.10 μg g^?1 in SPM, and 0.93–34.70 μg g^?1 in sediment. The partition coefficients (K_d1) of PAEs in water and SPM phase ranged from 0.004 to 3.36 L g^?1 in the wet season and from 0.12 to 2.84 L g^?1 in the dry season. K_d2 of PAEs in water and sediment phase was 0.001–9.75 L g^?1 in the wet season and 0.006–8.05 L g^?1 in the dry season. The dominant PAEs were DIBP, DBP, and DEHP in water and SPM, DIBP, DEHP, and DOP in sediment. The concentration of DBP in water exceeded the China Surface Water Standard. The discharge of domestic sewage and industrial wastewater might be the main potential sources of PAEs. The risk quotient (RQ) method used for the risk assessment revealed that DBP (0.01 < RQ < 1) posed a medium risk, while DIBP and DEHP (RQ > 1) posed a high environmental risk in water, DIBP (RQ > 1) also showed a high risk in sediment.

     

Application of neutral electrolyzed water spray for reducing dust levels in a layer breeding house

Reducing airborne dust is an essential process for improving hen housing environment. Dust reduction effects of neutral electrolyzed water (pH 8.2) spray were investigated in a commercial tunnel-ventilated layer breeding house during production in northern China. A multipoint sampler was used to measure airborne dust concentration to study the dust reduction effects and distribution in the house. Compared with the control treatment (without spray), airborne dust level was reduced 34% in the 3 hr after spraying 216 mL m^?2 neutral electrolyzed water in the breeding house. The dust concentration was significantly higher during the periods of feed distribution (1.13 ± 0.13 mg m^?3) and artificial insemination (0.72 ± 0.13 mg m^?3) compared with after spray (0.47 ± 0.09 mg m^?3) and during lights-off period (0.29 ± 0.08 mg m^?3) in the three consecutive testing days (P < 0.05). The experimental cage area was divided into four zones along the length of the house, with zone 1 nearest to the evaporative cooling pad and zone 4 nearest to the fans. The air temperature, relative humidity, airflow rate, and dust concentration were measured at the sampling points of the four zones in 3 consecutive days and mortality of the birds for the duration of a month were investigated. The results showed that the air temperature, airflow rate, dust concentration, and number of dead birds increase from zone 1 to zone 4 in the tunnel-ventilated layer breeding house.

Implications: It is difficult to effectively reduce hen house airborne dust levels and limited information is available on airborne dust distribution in tunnel-ventilated hen houses. This work investigates (i) the application of neutral electrolyzed water spray for reducing dust in a layer breeding houses; (ii) dust concentration variations in 24-hr house operation; as well as (iii) the effects of location on dust concentrations. It was demonstrated that neutral electrolyzed water spray can be efficiently used for dust reduction in poultry houses. Further, a better understanding of the dust concentration variations in 24-hr house operation and in different spatial zones can contribute to bird housing environment management and poultry house design so as to improve bird health.     

Emission factors and exposures from ground-level pyrotechnics

Potential exposures from ground-level pyrotechnics were assessed by air monitoring and developing emission factors. Total particulate matter, copper and SO₂ exposures exceeded occupational health guidelines at two outdoor performances using consumer pyrotechnics. Al, Ba, B, Bi, Mg, Sr, Zn, and aldehyde levels were elevated, but did not pose a health hazard based on occupational standards. Emission factors for total particulate matter, metals, inorganic ions, aldehydes, and polyaromatic hydrocarbons (PAHs) were determined for seven ground-supported pyrotechnics through air sampling in an airtight room after combustion. Particle generation ranged from 5 to 13% of the combusted mass. Emission factors (g Kg^?1) for metals common to pyrotechnics were also high: K, 23–45; Mg, 1–7; Cu, 0.05–7; and Ba, 0.03–6. Pb emission rates of 1.6 and 2.7% of the combusted mass for two devices were noteworthy. A high correlation (r² ≥ 0.89) between metal concentrations in pyrotechnic compositions and emission factors were noted for Pb, Cr, Mg, Sb, and Bi, whereas low correlations (r² ≤ 0.1) were observed for Ba, Sr, Fe, and Zn. This may be due to the inherent heterogeneity of multi-effect pyrotechnics. The generation of inorganic nitrogen in both the particulate (NO₂^?, NO₃^?) and gaseous (NO, NO₂) forms varied widely (<0.1–1000 mg Kg^?1). Aldehyde emission factors varied by two orders of magnitude even though the carbon source was carbohydrates and charcoal for all devices: formaldehyde (<7.0–82 mg Kg^?1), acetaldehyde (43–210 mg Kg^?1), and acrolein (1.9–12 mg Kg^?1). Formation of lower molecular weight PAHs such as naphthalene and acenaphthylene were favored, with their emission factors being comparable to that from the combustion of household refuse and agricultural debris. Ba, Sr, Cu, and Pb had emission factors that could produce exposures exceeding occupational exposure guidelines. Sb and unalloyed Mg, which are banned from consumer fireworks in the US, were present in significant amounts.     

Risk assessment of PBDEs and PAHs in house dust in Kocaeli,Turkey: levels and sources

Indoor dust samples were collected from 40 homes in Kocaeli, Turkey and were analyzed simultaneously for 14 polybrominated diphenyl ethers (PBDEs) and 16 poly aromatic hydrocarbons (PAHs) isomers. The total concentrations of PBDEs (Σ₁₄PBDEs) ranged from 29.32 to 4790 ng g^?1, with a median of 316.1 ng g^?1, while the total indoor dust concentrations of 16 PAHs (Σ₁₆PAHs) extending over three to four orders of magnitude ranged from 85.91 to 40,359 ng g^?1 with a median value of 2489 ng g^?1. Although deca-PBDE products (BDE-209) were the principal source of PBDEs contamination in the homes (median, 138.3 ng g^?1), the correlation in the homes was indicative of similar sources for both the commercial penta and deca-PBDE formulas. The PAHs diagnostic ratios indicated that the main sources of PAHs measured in the indoor samples could be coal/biomass combustion, smoking, and cooking emissions. For children and adults, the contributions to ∑₁₄PBDEs exposure were approximately 93 and 25 % for the ingestion of indoor dust, and 7 and 75 % for dermal contact. Exposure to ∑₁₆PAHs through dermal contact was the dominant route for both children (90.6 %) and adults (99.7 %). For both groups, exposure by way of inhalation of indoor dust contaminated with PBDEs and PAHs was negligible. The hazard index (HI) values for BDE-47, BDE-99, BDE-153, and BDE-209 were lower than the safe limit of 1, and this result suggested that none of the population groups would be likely to experience potential health risk due to exposure to PBDEs from indoor dust in the study area. Considering only ingestion + dermal contact, the carcinogenic risk levels of both B2 PAHs and BDE-209 for adults were 6.2 × 10^?5 in the US EPA safe limit range while those for children were 5.6 × 10^?4 and slightly higher than the US EPA safe limit range (1 × 10^?6 and 1 × 10^?4). Certain precautions should be considered for children.     

Arsenic, copper, and zinc contamination in soil and wheat during coal mining, with assessment of health risks for the inhabitants of Huaibei, China

Field studies were conducted to investigate arsenic (As), copper (Cu), and zinc (Zn) contamination in agricultural soils and wheat crops at two areas in Huaibei, China. Area A is in the proximity of Shuoli coal mine. In area B, three coal mines and a coal cleaning plant were distributed. The potential health risk of As, Cu, and Zn exposure to the local inhabitants through consumption of wheat grains was also estimated. The results showed that significantly higher (p?<?0.05) concentrations of As, Cu, and Zn were found in soils collected from area B than in those from area A. Arsenic concentrations in wheat sampled from area A were negatively correlated with the distance from the coal mine (p?<?0.001). Concentrations of Cu and Zn in wheat seedlings and grains collected from area B were significantly higher (p?<?0.05) than in those collected from area A, with the exception of Zn in wheat seedlings. Concentrations of Cu and Zn in most wheat grain samples were above the permissible limits of Cu and Zn in edible plants set by the Food and Agriculture Organization/World Health Organization. The hazard index of aggregate risk through consumption of wheat grains was 2.3–2.4 for rural inhabitants and 1.4–1.5 for urban inhabitants. The average intake of inorganic As for rural inhabitants in Huaibei was above 10 μg day^?1. These findings indicated that the inhabitants around the coal mine are experiencing a significant potential health risk due to the consumption of locally grown wheat.     

Dry and wet deposition of water-insoluble dust and water-soluble chemical species during spring 2007 in Tsukuba,Japan

Dry and wet depositions were sampled daily in Tsukuba, Japan, in spring 2007. Temporal variations in the dry and wet deposition fluxes of dust and water-soluble chemical species were controlled largely by air mass origin, the water vapor mixing ratio, and Asian dust events. The contribution of local sources to dry deposition of dust was large when the wind speed was high. Dry deposition fluxes of water-soluble chemical species were larger in humid air masses than in dry air masses. Wet deposition fluxes of dust and water-soluble chemical species indicated that air masses that passed over dust source regions and industrial regions became mixed with the maritime air masses over the coastal site of the Asian continent and western part of the Japanese islands. The total deposition of dust was 4220 mg m^?2 month^?1, and that of water-soluble chemical species ranged from 10 to 636 mg m^?2 month^?1. Wet deposition fluxes of the total deposition flux of dust accounted for 72% and those of water-soluble chemical species was for 72–96%. In particular, the largest wet deposition occurred during a single Asian dust event on 3 April. This event accounted for 23% (950 mg m^?2 month^?1) of the monthly dust deposition flux and for 2–28% (0.43–51 mg m^?2 month^?1) of the monthly deposition flux of water-soluble chemical species. This result implies that the wet deposition flux associated with even one sporadic Asian dust event can have extensive impacts on both terrestrial and oceanic ecosystems in East Asia.     

Evaluating levels and health risk of heavy metals in exposed workers from surgical instrument manufacturing industries of Sialkot,Pakistan

The study aimed to monitor heavy metal (chromium, Cr; cadmium, Cd; nickel, Ni; copper, Cu; lead, Pb; iron, Fe; manganese, Mn; and zinc, Zn) footprints in biological matrices (urine, whole blood, saliva, and hair), as well as in indoor industrial dust samples, and their toxic effects on oxidative stress and health risks in exposed workers. Overall, blood, urine, and saliva samples exhibited significantly higher concentrations of toxic metals in exposed workers (Cr; blood 16.30 μg/L, urine 58.15 μg/L, saliva 5.28 μg/L) than the control samples (Cr; blood 5.48 μg/L, urine 4.47 μg/L, saliva 2.46 μg/L). Indoor industrial dust samples also reported to have elevated heavy metal concentrations, as an example, Cr quantified with concentration of 299 mg/kg of dust, i.e., more than twice the level of Cr in household dust (136 mg/kg). Superoxide dismutase (SOD) level presented significant positive correlation (p?≤?0.01) with Cr, Zn, and Cd (Cr?>?Zn?>?Cd) which is an indication of heavy metal’s associated raised oxidative stress in exposed workers. Elevated average daily intake (ADI) of heavy metals resulted in cumulative hazard quotient (HQ) range of 2.97–18.88 in workers of different surgical units; this is an alarming situation of health risk implications. Principal component analysis-multiple linear regression (PCA-MLR)-based pie charts represent that polishing and cutting sections exhibited highest metal inputs to the biological and environmental matrices than other sources. Heavy metal concentrations in biological matrices and dust samples showed a significant positive correlation between Cr in dust, urine, and saliva samples. Current study will help to generate comprehensive base line data of heavy metal status in biomatrices and dust from scientifically ignored industrial sector. Our findings can play vital role for health departments and industrial environmental management system (EMS) authorities in policy making and implementation.     

Physicochemical variations in atmospheric aerosols recorded at sea onboard the Atlantic–Mediterranean 2008 Scholar Ship cruise (Part I): Particle mass concentrations,size ratios,and main chemical components

We report on ambient atmospheric aerosols present at sea during the Atlantic–Mediterranean voyage of Oceanic II (The Scholar Ship) in spring 2008. A record was obtained of hourly PM₁₀, PM_2.5, and PM₁ particle size fraction concentrations and 24-h filter samples for chemical analysis which allowed for comparison between levels of crustal particles, sea spray, total carbon, and secondary inorganic aerosols. On-board monitoring was continuous from the equatorial Atlantic to the Straits of Gibraltar, across the Mediterranean to Istanbul, and back via Lisbon to the English Channel. Initially clean air in the open Atlantic registered PM₁₀ levels <10 μg m^?3 but became progressively polluted by increasingly coarse PM as the ship approached land. Away from major port cities, the main sources of atmospheric contamination identified were dust intrusions from North Africa (NAF), smoke plumes from biomass burning in sub-Saharan Africa and Russia, industrial sulphate clouds and other regional pollution sources transported from Europe, sea spray during rough seas, and plumes emanating from islands. Under dry NAF intrusions PM₁₀ daily mean levels averaged 40–60 μg m^?3 (30–40 μg m^?3 PM_2.5; c. 20 μg m^?3 PM₁), peaking briefly to >120 μg m^?3 (hourly mean) when the ship passed through curtains of higher dust concentrations amassed at the frontal edge of the dust cloud. PM₁/PM₁₀ ratios ranged from very low during desert dust intrusions (0.3–0.4) to very high during anthropogenic pollution plume events (0.8–1).     

Potential risk assessment of heavy metals by consuming shellfish collected from Xiamen, China

Concentrations of Hg, Pb, Cd, and Cr in 240 shellfish including oyster, short-necked clam, razor clam, and mud clam collected from six administrative regions in Xiamen of China were measured. The daily intakes of heavy metals through the consumption of shellfish were estimated based on both of the metal concentrations in shellfish and the consuming amounts of shellfish. In addition, the target hazard quotients (THQ) were used to evaluate the potential risk of heavy metals in shellfish on human body. Results showed that the concentrations of heavy metals in shellfish ranged at the following sequence: Cr > Cd > Pb > Hg. The concentrations of Hg and Pb in most samples were below the limits (0.3 mg?kg^?1 for Hg and 0.5 mg?kg^?1 for Pb) of national standard (GB 18406.4-2001) set in China. About 57 % of samples were found to contain more than 0.1 mg?kg^?1 of Cd, in which the highest level was found in oyster from Xiangan with a value of 1.21 mg?kg^?1. The average concentrations of Cd in oyster and mud clam samples were 0.338 and 0.369 mg?kg^?1, respectively, which were significantly higher (p?<?0.05) than those in the samples of short-necked clam and razor clam. The highest concentration of Cr was found to present in short-necked clam from Jimei with a value of 10.4 mg?kg^?1, but a mean value of 1.95 mg?kg^?1 in all the shellfish was observed, and no significant difference was found among the different sampling regions. The calculated daily intakes of Hg, Pb, Cd, and Cr through consuming the shellfish were 0.005, 0.122, 0.137, and 1.20 μg?kg^?1 day^?1, respectively, which accounted for 2.19, 3.42, 13.7, and 40.1 % of the corresponding tolerable limits suggested by the Joint FAO/WHO Expert Committee on Food Additives. The THQ values of the four metals were far below 1 for most samples, except for those of Cd and Cr in the four shellfish species with the mean values of 0.132 and 0.385, respectively. The highest THQ values of Cd were observed in the species of oyster (0.719) and mud clam (0.568). But the high THQ values of Cr observed in all the four species were derived from the applied reference dose (RfD) data of Cr(VI) due to the unavailable RfD value of total Cr. The results indicate that the intakes of heavy metals by consuming shellfish collected from Xiamen of China do not present an appreciable hazard risk on human health, but attention should be paid to consuming those with relatively high THQ values, such as oyster, mud clam, and short-necked clam.     

Characterization of contaminants and evaluation of the suitability for land application of maize and sludge biochars

Prior to the application of biochar as an agricultural improver, attention should be paid to the potential introduction of toxicants and resulting unintended impacts on the environment. In the present study, the concentrations of polycyclic aromatic hydrocarbons (PAHs), heavy metals, and mineral elements were determined in maize and sludge biochars produced at 100 °C increments between 200 and 700 °C. The concentration ranges of total PAHs were 358–5,136 μg kg^?1 in maize biochars and 179–70,385 μg kg^?1 in sludge biochars. The total heavy metals were detected at the following concentrations (mg kg^?1): Cu, 20.4–56.7; Zn, 59.7–133; Pb, 1.44–3.50; Cd, <0.014; Cr, 8.08–21.4; Ni, 4.38–9.82 in maize biochars and Cu, 149–202; Zn, 735–986; Pb, 54.7–74.2; Cd, 1.06–1.38; Cr, 180–247; Ni, 41.1–56.1 in sludge biochars. The total concentrations of PAHs and heavy metals in all maize biochars and most sludge biochars were below the control standards of sludge for agricultural use in China, the USA, and Europe. The leachable Mn concentrations in sludge biochars produced at below 500 °C exceeded the groundwater or drinking water standards of these countries. Overall, all the maize biochars were acceptable for land application, but sludge biochars generated at temperatures between 200 and 500 °C were unsuitable for application as soil amendments due to their potential adverse effects on soil and groundwater quality.     

Quantification of Saharan dust contribution to PM10 concentrations over Italy during 2003–2005

Italy is frequently affected by Saharan dust intrusions, which result in high PM₁₀ concentrations in the atmosphere and can cause the exceedances of the PM₁₀ daily limits (50 μg m^?3) set by the European Union (EU/2008/50). The estimate of African dust contribution to PM₁₀ concentrations is therefore a key issue in air quality assessment and policy formulation. This study presents a first identification of Saharan dust outbreaks as well as an estimate of the African dust contribution to PM₁₀ concentrations during the period 2003–2005 over Italy. The identification of dust events has been carried out by looking at different sources of information such as monitoring network observations, satellite images, ground measurements of aerosol optical properties, dust model simulations and air mass backward trajectory analysis. The contribution of Saharan dust to PM₁₀ monthly concentrations has been estimated at seven Italian locations. The results are both spatially (with station) and temporally (with month and year) variable, as a consequence of the variability of the meteorological conditions. However, excluding the contribution of severe dust events (21st February 2004, 25th–28th September 2003, 23rd–27th March 2005), the monthly contribution of dust varies approximately between 1 μg m^?3 and 10 μg m^?3 throughout year 2005 and between 1 μg m^?3 and 8 μg m^?3 throughout year 2003. In 2004 the dust concentration is lower than 2003 and 2005 (<5 μg m^?3 at all sites). The reduction in the number of daily exceedances of the limit value (50 μg m^?3) after subtraction of the dust contribution is also calculated at each station: it varies with station between 20% and 50% in 2005 and between 5% and 25% in 2003 and 2004.     

Organic carbon,total nitrogen,and water-soluble ions in clouds from a tropical montane cloud forest in Puerto Rico

Chemical characterization to determine the organic and nitrogen fractions was performed on cloud water samples collected in a mountaintop site in Puerto Rico. Cloud water samples showed average concentrations of 1.09 mg L^?1 of total organic carbon (TOC), of 0.85 mg L^?1 for dissolved organic carbon (DOC) and of and 1.25 mg L^?1 for total nitrogen (TN). Concentrations of organic nitrogen (ON) changed with the origin of the air mass. Changes in their concentrations were observed during periods under the influence of African dust (AD). The ON/TN ratios were 0.26 for the clean and 0.35 for the AD periods. Average concentrations of all these species were similar to those found in remote environments with no anthropogenic contribution. In the AD period, for cloud water the concentrations of TOC were 4 times higher and TN were 3 times higher than during periods of clean air masses associated with the trade winds. These results suggest that a significant fraction of TOC and TN in cloud and rainwater is associated to airborne particulate matter present in dust. Functional groups were identified using proton nuclear magnetic resonance (¹H NMR) spectroscopy. This characterization led to the conclusion that water-soluble organic compounds in these samples are mainly aliphatic oxygenated compounds, with a small amount of aromatics. The ion chromatography results showed that the ionic species were predominantly of marine origin, for air masses with and without African dust influence, with cloud water concentrations of NO₃^? and NH₄⁺ much lower than from polluted areas in the US. An increase of such species as SO₄^2?, Cl^?, Mg²⁺, K⁺ and Ca²⁺ was seen when air masses originated from northwest Africa. The changes in the chemical composition and physical properties of clouds associated with these different types of aerosol particles could affect on cloud formation and processes.