First world-wide interlaboratory study on polybrominated diphenylethers (PBDEs)

The first world-wide interlaboratory study on PBDEs, organised between November 1999 and April 2000, involved five biological samples, two sediments and two standard solutions. These materials were sent to 26 participants in nine different countries. Results were returned from 18 laboratories. The results reported for BDE 47 were acceptable with a range of relative standard deviations (Rsd) of 17-40%. Results for the BDEs 99 (Rsd 25-77%), BDE 100 (Rsd 19-48%), 153 (Rsd 30-48%) and 154 (Rsd 25-43%) showed that a further improvement of these analyses is needed. The BDE 209 analysis is not under the control of the participating laboratories. The data reported for the biota samples were very variable and for the two sediments Rsd values of 48% and 78% were obtained. It is recommended that analysts pay more attention to the special requirements for the BDE 209 analysis such as avoiding exposure to intensive light and exposure for too long times to too high temperatures.     

Heavy metal speciation and phytotoxic effects of three representative sewage sludges for agricultural uses

The environmental impact of sewage sludges depends on the availability and phytotoxicity of their heavy metal. The influence of representative sludges (dewatered anaerobic, pelletization, and composted sludge) on the availability of heavy metals, and their effects on seed germination were compared. The total heavy metal concentrations were below the maximum permitted for land-applied waste and the differences among them were small. The DTPA-extracted metal concentrations were rather different. The sequential extraction of the compost showed a slight increase in Cd and Cu availability, and a decrease in the availability of Fe, Mn, Ni and Zn. Pelletization increased the availability of Ni and slightly reduced that of Cr. The dewatering sludge led to greater availability of Cr and Mn but reduced the concentration of Cd. The three different sludges also affected seed germination and root elongation in different ways. The most serious adverse effects were caused by the dewatered sludge extract.     

Comparison of the toxicogenetic potential of sewage sludges from different treatment processes focusing agricultural use

Environmental Science and Pollution Research - A problem that has been dragging in recent decades is the final disposal of the waste produced in the wastewater treatment process. In addition to its...     

Zinc, copper and nickel concentrations in soil extracts and crops grown on four soils treated with metalloaded sewage sludges

Sludges containing high concentrations of zinc, copper or nickel and an uncontaminated sludge were added to two sandy loams (pH 6.5 and 7.1), a heavy clay (pH 6.3) and a calcareous clay (pH 7.8) to give ten sludge treatments for each soil. The mixtures were incubated fallow, cropped continuously with clover, or cropped with barley and red beet in rotation for 21 months. The quantity of added metal either in the soil solution or extracted by 0.1m CaCl(2) depended on the metal loading, pH and soil cation exchange capacity, and changed with time after mixing soils and sludges. Crop metal concentrations, and the occurrence of metal-induced yield reductions, also depended on soil properties as well as metal loading. The best chemical extractant for predicting plant metal concentrations was 0.1m CaCl(2).     

An intercalibration study on organobromine compounds: Results on polybrominated diphenylethers and related dioxin-like compounds

An intercalibration study on organobromine compounds has been conducted to evaluate the accuracy and reliability in the analysis of brominated flame retardants (BFRs) such as polybrominated diphenyl ethers (PBDEs) and their related compounds like polybrominated and monobromo-polychlorinated dibenzodioxins and -furans (PBDDs/DFs, MoBPCDDs/DFs). This paper reports the results for these compounds in 'Mixed Standard Solutions' and 'Air-Dried Sediment'. The relative standard deviations (RSDs) for PBDEs, PBDDs/DFs and MoBPCDDs/DFs in mixed standard solutions ranged from 9% to 24%, 4% to 20% and 8% to 27%, respectively. The results of this study are better than those reported in earlier international interlaboratory studies due to general improvement in analytical methods and an increasing number of available authentic standards, particularly for PBDEs. In the analysis for higher brominated compounds such as octabromodibenzodioxin, the participants were advised to optimize the calibration curves befitting the range of concentrations found in samples because variation of relative response factors was noted. The results for 'Air-Dried Sediment' were also reasonable with RSDs from 10% to 38% for PBDEs, 8% to 38% for PBDDs/DFs and 17% to 36% for MoBPCDDs/DFs. In the sediment sample, possible errors in the sample pretreatment and/or interference by other compounds/impurities were indicated. The concentrations of pentabromodiphenylether, BDE100, varied more than the other PBDE isomers due to its poor separation in some chromatographic conditions. In addition, interference by PBDEs was observed in the analysis for PBDFs. Potential degradation/secondary formulation of PBDEs and PBDFs during the Soxhlet extraction were suggested when copper powder was added into the sediment samples. Inspite of these observations, the results in this study are better than those reported in other interlaboratory studies due to the advice given to participants for improving the results. Compared with the results for PCDDs/DFs (5-23% RSDs) and Co-PCBs (6-24% RSDs), the RSDs for most of the organobromine compounds were high, indicating an immature QA/QC approach for the analysis of PBDEs and related compounds in comparison to common chlorinated dioxins.     

Occurrence of polybrominated diphenylethers, polychlorinated dibenzo-p-dioxins, dibenzofurans and biphenyls in coastal sediments from Spain

Fifteen sediment samples were analysed in order to determine their content of polybrominated diphenylethers (PBDEs), polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs) and biphenyls (PCBs). Samples were collected from several hot spots on the Spanish coast, such as the harbours of Almeria and Tarragona, and the mouths of the Besos and Llobregat rivers in Barcelona. A generic analytical procedure based on Soxhlet extraction followed by an automated cleanup system and gas chromatography-ion trap-mass spectrometry was employed for determining the toxic congeners of PCDDs and PCDFs, as well as dioxin-like PCBs. As regards PBDE determinations, a rapid method based on the use of selective pressurized liquid extraction followed by gas chromatography-negative ion chemical ionization-mass spectrometry was applied. Total toxicity equivalent (WHO-TEQ) values were calculated using the toxicity equivalent factors proposed by WHO for dioxin-like PCBs, PCDDs and PCDFs. WHO-TEQ values ranged from 0.3 to 75 pg/g dry weight (dw), with PCB contribution on the toxicity of the samples between 1 and 84%. Total PBDE levels ranged from 2.7 to 134 ng/g dw, with BDE-209 contribution on the total PBDE contamination between 50 and 99%.     

Soot-water distribution coefficients for polychlorinated dibenzo-p-dioxins,polychlorinated dibenzofurans and polybrominated diphenylethers determined with the soot cosolvency-column method

For many types of hydrophobic compounds, sorption non-linearity and solid-water distributions in the field well above expectations from organic matter partitioning models have lead to the proposition that strong adsorption to soot surfaces may not be limited to polycyclic aromatic hydrocarbons but may extend as a significant process for many aromatic compound classes. Here, the soot-water distribution coefficients (Ksc) were determined with the soot cosolvency-column method for homolog series of five polychlorinated dibenzo-p-dioxins (PCDDs), five polychlorinated dibenzofurans (PCDFs) and for two polybrominated diphenylethers (PBDEs). All compounds exhibited significantly stronger association with soot carbon than expected from estimates of their bulk organic-carbon normalized partition coefficients (Koc). The Ksc/Koc ratios (at aqueous concentrations of around 0.1-1 microg/l) were for PCDDs (up to tetrachlorination) 19-130 (median 25), for PCDFs (also up to tetrachlorination) 150-490 (median 300), and for both the tetra- and pentabrominated PBDEs a factor of 60. The particularly strong soot sorption for the PCDFs is of similar enhancement factors as previously elucidated for polycyclic aromatic hydrocarbons. Compound-class specific correlations between log Ksc and octanol-water partition coefficients (log Kow) were significant for both PCDDs and PCDFs (and with R2 > 98%). These may prove useful for anticipating variable fractions of dissolved exposures between different environmental regimes and putative remediation objects.     

中国部分城市污泥中矿质元素形态与生物可利用性研究

近年来随着城市污水处理厂数目迅速增加,低成本、高效率的污泥农用受到越来越多的关注。研究从北到南的五家污水处理厂消化污泥中矿质元素的含量和形态分布,为污泥资源化的合理利用提供科学参考。结果表明：消化污泥总体呈高有机质、高氮磷、低K、高矿质元素营养的相似性,但其理化性质如阳离子交换容量(CEC)、pH等差异较大,对矿质元素的形态分布与生物可利用性有明显的影响。同种元素在不同污泥中含量的差异较大,相差数倍,甚至十倍以上。污泥中不同元素含量明显不同,Fe的浓度最高,次之是Mg、Zn、B的浓度最低。连续提取研究表明,污泥pH对污泥中矿质元素的形态分布有明显影响,酸性污泥(厦门污水处理厂)中各矿质元素酸溶／交换态百分率明显高于其他污泥。Cu主要分布在氧化态;Zn的三态分布百分率均在10％以上;Mg、Mn的酸溶／交换态含量较高;Fe主要分布在残渣态;B氧化态和还原态的百分率较高。建议在全国范围内进行一次污水处理厂污泥品质调查,为污泥合理农用提供科学依据。     

Ecological restoration of mine degraded soils,with emphasis on metal contaminated soils

This paper reviews the ecological aspects of mined soil restoration, with special emphasis on maintaining a long-term sustainable vegetation on toxic metal mine sites. The metal mined soils are man-made habitats which are very unstable and will become sources of air and water pollution. Establishment of a vegetation cover is essential to stabilize the bare area and to minimize the pollution problem. In addition to remediate the adverse physical and chemical properties of the sites, the choice of appropriate vegetation will be important. Phytostabilization and phytoextraction are two common phytoremediation techniques in treating metal-contaminated soils, for stabilizing toxic mine spoils, and the removal of toxic metals from the spoils respectively. Soil amendments should be added to aid stabilizing mine spoils, and to enhance metal uptake accordingly.     

Extractability and mobility of mercury from agricultural soils surrounding industrial and mining contaminated areas

This study focussed on a comparison of the extractability of mercury in soils with two different contamination sources (a chlor-alkali plant and mining activities) and on the evaluation of the influence of specific soil properties on the behaviour of the contaminant. The method applied here did not target the identification of individual species, but instead provided information concerning the mobility of mercury species in soil. Mercury fractions were classified as mobile, semi-mobile and non-mobile.The fractionation study revealed that in all samples mercury was mainly present in the semi-mobile phase (between 63% and 97%). The highest mercury mobility (2.7 mg kg⁻¹) was found in soils from the industrial area. Mining soils exhibited higher percentage of non-mobile mercury, up to 35%, due to their elevated sulfur content.Results of factor analysis indicate that the presence of mercury in the mobile phase could be related to manganese and aluminium soil contents. A positive relation between mercury in the semi-mobile fraction and the aluminium content was also observed. By contrary, organic matter and sulfur contents contributed to mercury retention in the soil matrix reducing the mobility of the metal.Despite known limitations of sequential extraction procedures, the methodology applied in this study for the fractionation of mercury in contaminated soil samples provided relevant information on mercury’s relative mobility.     

Analysis of potentially toxic metal constraints to apply sewage sludge in Portuguese agricultural soils

Environmental Science and Pollution Research - The application of sewage sludge (SS) in the soil can be a valuable way to increase its content of organic matter. However, the concentration of...     

Persistence and fate of polychlorinated biphenyls (PCBs) in sewage sludge-amended agricultural soils

Four metal enriched sewage sludges containing different concentrations of polychlorinated biphenyls (PCBs) were applied to two field soils in the UK in 1968. Samples of the sludges, sludge-amended soils and soils from untreated control plots were stored and analysed retrospectively. Sludge concentrations ranged from 1 to 7 mg SigmaPCB kg(-1). The pattern of PCBs was similar in three of the four sludges, with congeners 14, 18, 28 and 52 present at the highest concentrations. The fourth sludge contained higher amounts of congeners 149, 153, 138 and 180. SigmaPCB concentrations in control plot soil have declined over the last 20 years, indicating a reduction in atmospheric deposition inputs of PCBs to the soil. SigmaPCB concentrations also declined on the sludge-amended plots, reaching control plot concentrations (30-60 microg SigmaPCB kg(-1)) in the late-1980s. Half-lives ranged from < 1 to 8.5 years for congeners 18, 28 and SigmaPCB. Biodegradation and/or the formation of reversibly sorbed soil PCB residues could not account for the losses observed. Volatilisation is implicated as the most important loss process on both the control and sludge-amended plots. Using the fugacity approach, congener concentrations in soils at Luddington were predicted still to have not reached equilibrium with the air. Further losses to the atmosphere are likely.     

Extractability and mobility of mercury from agricultural soils surrounding industrial and mining contaminated areas

This study focussed on a comparison of the extractability of mercury in soils with two different contamination sources (a chlor-alkali plant and mining activities) and on the evaluation of the influence of specific soil properties on the behaviour of the contaminant. The method applied here did not target the identification of individual species, but instead provided information concerning the mobility of mercury species in soil. Mercury fractions were classified as mobile, semi-mobile and non-mobile. The fractionation study revealed that in all samples mercury was mainly present in the semi-mobile phase (between 63% and 97%). The highest mercury mobility (2.7 mg kg(-1)) was found in soils from the industrial area. Mining soils exhibited higher percentage of non-mobile mercury, up to 35%, due to their elevated sulfur content. Results of factor analysis indicate that the presence of mercury in the mobile phase could be related to manganese and aluminium soil contents. A positive relation between mercury in the semi-mobile fraction and the aluminium content was also observed. By contrary, organic matter and sulfur contents contributed to mercury retention in the soil matrix reducing the mobility of the metal. Despite known limitations of sequential extraction procedures, the methodology applied in this study for the fractionation of mercury in contaminated soil samples provided relevant information on mercury's relative mobility.     

The use of maize and poplar in chelant-enhanced phytoextraction of lead from contaminated agricultural soils

Chelant-enhanced phytoextraction of heavy metals is an emerging technological approach for a non-destructive remediation of contaminated soils. The main objectives of this study were (i) to assess the extraction efficiency of two different synthetic chelating agents (ethylenediaminetetraacetic acid (EDTA) and ethylenediaminedisuccinic acid (EDDS)) for desorbing Pb from two contaminated agricultural soils originating from a mining and smelting district and (ii) to assess the phytoextraction efficiency of maize (Zea mays) and poplar (Populus sp.) after EDTA application. EDTA was more efficient than EDDS in desorbing and complexing Pb from both soils, removing as much as 60% of Pb. Maize exhibited better results than poplar when extracting Pb from the more acidic (pH approximately 4) and more contaminated (up to 1360 mg Pb kg(-1)) agricultural soil originating from the smelting area. On the other hand, poplars proved to be more efficient when grown on the near-neutral (pH approximately 6) and less contaminated (up to 200 mg Pb kg(-1)) agricultural soil originating from the mining area. Furthermore, the addition of EDTA led to a significant increase of Pb content especially in poplar leaves, proving a strong translocation rate within the poplar plants.     

The use of poplar during a two-year induced phytoextraction of metals from contaminated agricultural soils

The efficiency of poplar (Populus nigra L.xPopulus maximowiczii Henry.) was assessed during a two-year chemically enhanced phytoextraction of metals from contaminated soils. The tested metal mobilizing agents were EDTA (ethylenediaminetetraacetic acid) and NH4Cl. EDTA was more efficient than chlorides in solubilizing metals (especially Pb) from the soil matrix. The application of chlorides only increased the solubility of Cd and Zn. However, the increased uptake of metals after the application of higher concentrations of mobilizing agents was associated with low biomass yields of the poplar plants and the extraction efficiencies after the two vegetation periods were thus comparable to the untreated plants. Additionally, the application of mobilizing agents led to phytotoxicity effects and increased mobility of metals. Higher phytoextraction efficiencies were observed for Cd and Zn compared to Pb and Cu. Poplars are therefore not suitable for chemically enhanced phytoextraction of metals from severely contaminated agricultural soils.     

Sorption kinetic characteristics of polybrominated diphenyl ethers on natural soils

Sorption kinetic characteristics of BDE-28 and BDE-47 on five natural soils with different organic carbon fractions were investigated, and could be satisfactorily described by a two (fast and slow)-compartment first-order model with the ratio of rate constants ranged from 9 to 94 times. The fast compartment made a dominant contribution (71% ∼ 94%) to the total sorption amount in the whole process, and accounted for over 90% of the increase in the total sorption amount at initial 5 h. The influence of the slow compartment on the increase in the total sorption amount became principal (above 90%) in the subsequent stage approximately from 9 h or 25 h to the apparent equilibrium at 265 h. The results proposed the different sorption behaviors of the mathematically classified compartments for BDE-28 and BDE-47, which may correspond to the different soil components, such as soil organic fractions with amorphous and condensed structures, respectively.     

The persistence of polynuclear aromatic hydrocarbons (PAHs) in sewage sludge amended agricultural soils

In 1968, five metal enriched sewage sludges containing different concentrations of polynuclear aromatic hydrocarbons (PAHs) were applied to different plots on field soils at two experimental sites, Luddington and Lee Valley, in the UK. This resulted in substantial increases in the total PAH soil concentrations in all plots. Since application, losses have occurred, with the high molecular weight PAHs being more persistent. Calculated half-lives range from under 2 years for naphthalene to over 9 years for benzo[ghi]perylene and coronene. The losses of PAH compounds in these field experiments can be related, in part, to their physico-chemical properties, notably the octanol: water partition coefficient.     

Simple and sequential extractions of heavy metals from different sewage sludges

The presence of heavy metals in the sludges produced in waste-water treatment plants restricts their use for agricultural purposes. This study looks at different types of sludges (aerobic, anaerobic, unstabilised and sludge from a waste stabilisation pond) and compares the distribution of the heavy metals they contain according to the treatment that they have undergone. Some agronomic parameters necessary for characterising a sludge as suitable for use as amendment were determined. The aim of this study is to compare the availability and the localisation of heavy metals in different sewage sludges using simple (water and DTPA) extraction and the BCR (Community Bureau of Reference) sequential extraction procedure. It was confirmed that the total concentration of heavy metals did not exceed the limits set out by European legislation and that the stabilisation treatment undergone by the sludges strongly influenced the heavy metal distribution and the phases to which they were associated and their bioavailability level. The DTPA extraction procedure is cheap and easy to perform and the obtained results are similar to those obtained with the sequential procedure.     

Effects of long-term soil amendment with sewage sludges on soil humic acid thermal and molecular properties

Sewage sludges are frequently used as soil amendments due to their high contents of organic matter and nutrients, particularly N and P. However, their effects upon the chemistry of soil humic acids, one of the main components of the soil organic matter, need to be more deeply studied in order to understand the relation between organic matter structure and beneficial soil properties. Two sewage sludges subjected to different types of pre-treatment (composted and thermally dried) with very different chemical compositions were applied for three consecutive years to an agricultural soil under long-term field study. Thermal analysis (TG–DTG–DTA) and solid-state ¹³C NMR spectroscopy were used to compare molecular and structural properties of humic acids isolated from sewage sludges, and to determine changes in amended soils. Thermally dried sewage sludge humic acids showed an important presence of alkyl and O/N-alkyl compounds (70%) while composted sludge humic acids comprised 50% aromatic and carbonyl carbon. In spite of important differences in the initial chemical and thermal properties of the two types of sewage sludges, the chemical and thermal properties of the soil humic acids were quite similar to one another after 3 years of amendment. Long-term application of both sewage sludges resulted in 80–90% enrichment in alkyl carbon and organic nitrogen contents of the soil humic acid fraction.     

Effects of long-term soil amendment with sewage sludges on soil humic acid thermal and molecular properties

Sewage sludges are frequently used as soil amendments due to their high contents of organic matter and nutrients, particularly N and P. However, their effects upon the chemistry of soil humic acids, one of the main components of the soil organic matter, need to be more deeply studied in order to understand the relation between organic matter structure and beneficial soil properties. Two sewage sludges subjected to different types of pre-treatment (composted and thermally dried) with very different chemical compositions were applied for three consecutive years to an agricultural soil under long-term field study. Thermal analysis (TG–DTG–DTA) and solid-state ¹³C NMR spectroscopy were used to compare molecular and structural properties of humic acids isolated from sewage sludges, and to determine changes in amended soils. Thermally dried sewage sludge humic acids showed an important presence of alkyl and O/N-alkyl compounds (70%) while composted sludge humic acids comprised 50% aromatic and carbonyl carbon. In spite of important differences in the initial chemical and thermal properties of the two types of sewage sludges, the chemical and thermal properties of the soil humic acids were quite similar to one another after 3 years of amendment. Long-term application of both sewage sludges resulted in 80–90% enrichment in alkyl carbon and organic nitrogen contents of the soil humic acid fraction.