Integrated bioremediation of soil and groundwater at a superfund site

The soil and two aquifers under an active lumber mill in Libby, Montana, had been contaminated from 1946 to 1969 by uncontrolled releases of creosote and pentachlorophenol (PCP). In 1983, because the contaminated surface soil and the shallower aquifer posed immediate risks to human health and the natural environment, the U.S. Environmental Protection Agency placed the site on its National Priorities List. Feasibility studies in 1987 and 1988 determined that in situ bioremediation would help clean up this aquifer and that biological treatment would help clean up the contaminated soils. This article outlines the studies that led to a 1988 EPA record of decision and details the EPA-approved remedial plan implemented starting in 1989; EPA estimates a total cost of about $15 million (in 1988 dollars). The plan involves extensive excavation and biological treatment of shallow contaminated soils in two lined and bermed land treatment units, extraction of heavily contaminated groundwater, an aboveground bioreactor treatment system, and injection of oxygenated water to the contaminant source area, as well as to other on-site areas affected by the shallower aquifer's contaminant plume.     

Successful full‐scale enhanced anaerobic dechlorination at a NAPL strength 1,1,1‐TCA source area

Bioremediation of 1,1,1‐trichloroethane (TCA) is more challenging than bioremediation of other chlorinated solvents, such as tetrachloroethene (PCE) and trichloroethene (TCE). TCA transformation often occurs under methanogenic and sulfate‐reducing conditions and is mediated by Dehalobacter. The source area at the project site contains moderately permeable medium sand with a low hydraulic gradient and is approximately 0.5 acre. TCA contamination generally extended to 35 feet, with the highest concentrations at approximately 20 feet. The concentrations then decreased with depth; several wells contained 300 to 600 mg/L of TCA prior to bioremediation. The area of treatment also contained 2 to 30 mg/L of TCE from an upgradient source. Initial site groundwater conditions indicated minimal biotic dechlorination and the presence of up to 20 mg/L of nitrate and 90 mg/L of sulfate. Microcosm testing indicated that TCA dechlorination was inhibited by the site's relatively low pH (5 to 5.5) and high TCA concentration. After the pH was adjusted and TCA concentrations were reduced to less than 35 mg/L (by dilution with site water), dechlorination proceeded rapidly using whey (or slower with sodium lactate) as an electron donor. Throughout the remediation program, increased resistance to TCA inhibition (from 35 to 200 mg/L) was observed as the microbes adapted to the elevated TCA concentrations. The article presents the results of a full‐scale enhanced anaerobic dechlorination recirculation system and the successful efforts to eliminate TCA‐ and pH‐related inhibition. © 2012 Wiley Periodicals, Inc.     

Full‐scale bioremediation of a dilute 50‐acre plume

Enhanced anaerobic dechlorination is being conducted to remediate a 50‐acre groundwater area impacted with chlorinated volatile organic compounds (CVOCs). The plume, which is over 3,000 feet (ft) long, initially contained tetrachloroethene and breakdown products at concentrations of 2 to 3 milligrams per liter. The site's high groundwater flow velocity (greater than 1,000 ft per year) was incorporated into the design to help with amendment distribution. Bioaugmentation was conducted using a mixed culture containing Dehalococcoides ethenogenes. There is evidence that it has migrated to distances exceeding 600 ft. The major benefit of the high groundwater flow velocity is greater areal coverage by the remediation system, but the downside is the difficulty in delivering sufficient donor to create the required anaerobic conditions. Overall performance has been excellent with total CVOC reductions and conversion to ethene of 98 percent within a 25‐acre area downgradient of the treatment transect that has operated the longest. © 2011 Wiley Periodicals, Inc.     

Managing bioremediation of a creosote‐contaminated superfund site by optimizing moisture and temperature in a biopile

Soil moisture content and temperature in a contaminated soil biopile equipped with immobilized microbe bioreactors (IMBRs) were optimized during ex situ bioremediation at a creosote‐contaminated Superfund site. Efficiency of remediation during warm summer months without soil‐temperature and moisture optimization was compared with that of cold winter months when corrective measures were applied. Significant reduction (35 percent) in total polycyclic aromatic hydrocarbons (PAHs) was observed, compared to 3.97 percent without corrective measures (p < 0.05). Kinetic rates (KRs) for total PAH removal were significantly enhanced from 3.93 to 50.95 mg/kg/day. KRs for removal of high molecular mass four‐to‐six‐ring PAHs were also significantly enhanced from 70.29 mg/kg/day to 97.45 mg/kg/day ( p < 0.05). Bioremediation of two‐ and three‐ring PAHs increased significantly from 15 percent to 40 percent. Benzo[a]pyrene toxicity equivalent mass (BaP_equiv) was significantly reduced by 48 percent with KR of 0.47 mg/kg/day as compared to 22 percent with KR of 0.14 mg/kg/day (p < 0.05). Soil moisture content was enhanced from 15.7 percent to 41.4 percent. © 2007 Wiley Periodicals, Inc.     

Integrated approach to PCE‐impacted site characterization,site management,and enhanced bioremediation

Tetrachloroethene (PCE)‐ and trichloroethene (TCE)‐impacted sites pose significant challenges even when site characterization activities indicate that biodegradation has occurred naturally. Although site‐specific, regulatory, and economic factors play roles in the remedy‐selection process, the application of molecular biological tools to the bioremediation field has streamlined the assessment of remedial alternatives and allowed for detailed evaluation of the chosen remedial technology. The case study described here was performed at a PCE‐impacted site at which reductive dechlorination of PCE and TCE had led to accumulation of cis‐dichlorethene (cis‐DCE) with concentrations ranging from approximately 10 to 100 mg/L. Bio‐Trap® samplers and quantitative polymerase chain reaction (qPCR) enumeration of Dehalococcoides spp. were used to evaluate three remedial options: monitored natural attenuation, biostimulation with HRC®, and biostimulation with HRC‐S®. Dehalococcoides populations in HRC‐S‐amended Bio‐Traps deployed in impacted wells were on the order of 10³ to 10⁴ cells/bead but were below detection limits in most unamended and HRC‐amended Bio‐Traps. Thus the in situ Bio‐Trap study identified biostimulation with HRC‐S as the recommended approach, which was further evaluated with a pilot study. After the pilot HRC‐S injection, Dehalococcoides populations increased to 10⁶ to 10⁷ cells/bead, and concentrations of cis‐DCE and vinyl chloride decreased with concurrent ethene production. Based on these results, a full‐scale HRC‐S injection was designed and implemented at the site. As with the pilot study, full‐scale HRC‐S injection promoted growth of Dehalococcoides spp. and stimulated reductive dechlorination of the daughter products cis‐DCE and vinyl chloride. © 2008 Wiley Periodicals, Inc.     

Pilot‐scale evaluation of in situ cometabolic bioremediation of TCE in groundwater using PHOSter® technology

A study was conducted to evaluate the efficacy of PHOSter® technology for treating groundwater contaminated with trichloroethene (TCE) at Edwards Air Force Base, California. The technology consists of injecting a gaseous mixture of air, methane, and nutrients into groundwater with the objective of stimulating the growth of methanotrophs, a naturally occurring microbial group that is capable of catalyzing the aerobic degradation of chlorinated solvents into nontoxic products. Injection operations were performed at one well for a period of three months. Six monitoring wells were utilized for groundwater and wellhead vapor monitoring and for groundwater and microbial sampling. In the five monitoring wells located within 44 feet of the injection well, the following results were observed: dissolved oxygen concentrations increased to a range between 6 and 8 milligrams per liter (μg/L); the biomass of target microbial groups increased by one to five orders of magnitude; and TCE concentrations decreased by an average of 92 percent, and to below the California primary maximum contaminant level (MCL; 5 micrograms per liter [µg/L]) in the well closest to the injection well. © 2008 Wiley Periodicals, Inc. *

1 This article is a U.S. Government work and, as such, is in the public domain of the United States of America.

     

Slurry phase bioremediation of PAHs in industrial landfill samples at laboratory scale

The effect of Tween 80 and selected bacteria additions on the bioremediation of PAH contaminated landfill soil (70.38mgkg(-1)) was evaluated in a slurry phase bioreactor. A phenanthrene-degrading consortium was selected by enrichment cultures and used as autochthonous inoculum. The Tween 80 addition increased the aqueous concentration of both high and low molecular weight PAHs. In the experiment with Tween 80 and inoculum addition, added microorganisms improved (>90%) the biodegradation of two- and three-ring PAHs as well as of the four-ring PAHs pyrene and fluoranthene. Biodegradation of the higher molecular weight PAHs was about 30% in experiments with Tween 80 addition, with and without inoculum addition.     

Evaluation of natural attenuation at a 1,4‐dioxane‐contaminated site

1,4‐Dioxane entered the environment as a result of historic leaks and spills in the production area at an industrial facility in the southeastern coastal plain. The areal extent of the 1,4‐dioxane plume is several hundred acres and is largely contained on the site. Land use adjacent to the plant property is primarily undeveloped (wetlands or woods) or industrial, with a small area of mixed land use (commercial/residential) to the southwest and north. The surficial aquifer is a relatively simple hydrogeologic system with well‐defined boundaries and is comprised of a 50‐ to 70‐foot‐thick deposit of alluvial/fluvial sand and gravel that overlies an aquitard in excess of 100 feet thick. A groundwater flow model, developed and calibrated using field‐measured data, was used for the fate‐and‐transport modeling of 1,4‐dioxane. The flow‐and‐transport model, combined with the evaluation of other site geochemical data, was used to support the selection of monitored natural attenuation (MNA) as the proposed groundwater remedy for the site. Since the active sources of contamination have been removed and the modeling/field data demonstrated that the plume was stable and not expanding, the proposed MNA approach was accepted and approved by the regulatory agency for implementation in 2004. Subsequent accumulated data confirm that concentrations in the 1,4‐dioxane plume are declining as predicted by the fate‐and‐transport modeling. © 2008 Wiley Periodicals, Inc.     

Pilot‐scale evaluation using bioaugmentation to enhance PCE dissolution at dover AFB national test site

An Interstate Technology and Regulatory Council (ITRC) forum was recently held that focused on six case studies in which bioremediation of dense nonaqueous‐phase liquids (DNAPLs) was performed; the objective was to demonstrate that there is credible evidence for bioremediation as a viable environmental remediation technology. The first two case studies from the forum have been previously published; this third case study involves a pilot‐scale demonstration that investigated the effects of biological activity on enhancing dissolution of an emplaced tetrachloroethene (PCE) DNAPL source. It used a controlled‐release test cell with PCE as the primary DNAPL in a porous media groundwater system. Both laboratory tests and a field‐scale pilot test demonstrated that bioaugmentation can stimulate complete dechlorination to a nontoxic end product and that the mass flux from a source zone increases when biological dehalorespiration activity is enhanced through nutrient (electron donor) addition and bioaugmentation. All project goals were met. Important achievements include demonstrating the ability to degrade a PCE DNAPL source to ethene and obtaining significant information on the impacts to the microbial populations and corresponding isotope enrichments during biodegradation of a source area. © 2007 Wiley Periodicals, Inc.     

ERI evaluation of injectates used at a dry‐cleaning site

A former dry‐cleaning site in Jackson, Tennessee, has undergone remediation to treat dense nonaqueous‐phase liquid (trichloroethene [TCE] and tetrachloroethene [PCE]) contamination in the subsurface. The dry cleaning operation closed in 1977. In 2002, a series of injections were made at the site consisting of corn syrup, vegetable oils, and Simple Green®. In 2004, approximately 200 cubic yards of contaminated soil were excavated, and the bottom of the excavation was covered with sodium lactate. In 2009, the site was characterized using proprietary electrical resistivity imaging (ERI; commercially available as Aestus GeoTrax Surveys^TM). Follow‐up confirmation soil borings targeted anomalies detected via the geophysical work. The results indicate an extremely electrically conductive (less than 1 ohm‐m) vadose zone downgradient from the injection wells, and extremely electrically resistive areas (greater than 10,000 ohm‐m) in the phreatic zone near the injection area. The sample data indicate that the electrically resistive anomalous zones contain moderate to high concentrations of undegraded dry‐cleaning compounds. Electrically conductive anomalous zones are interpreted to be areas of biological activity generated by the amendments injected into the subsurface based on the extreme conductivity values detected, the chemical composition (i.e., PCE degradates are present), and the dominant vadose‐zone location of the conductive zones. © 2012 Wiley Periodicals, Inc.     

Phytoremediation of lead-contaminated soil at a New Jersey Brownfield site

Phytoremediation is a new technology that uses specially selected metal-accumulating plants as an attractive and economical method to clean up soils contaminated with heavy metals and radionuclides. The integration of specially selected metal-accumulating crop plants (Brassica juncea (L) Czern.) with innovative soil amendments allows plants to achieve high biomass and metal accumulation rates. In a recent study conducted at a lead-contaminated site in Trenton, New Jersey, the soil was treated with phytoremediation using successive crops of B. juncea combined with soil amendments. Through phytoremediation, the average surface soil lead concentration was reduced by 13 percent. In addition, the target soil concentration of 400 mg/kg was achieved in approximately 72 percent of the treated area in one cropping season.     

Sustainable wind‐driven bioventing at a petroleum hydrocarbon–impacted site

Bioventing—the injection of air into the vadose zone to increase microbial activity—is a commonly used, proven technology for remediating volatile organic compounds present in the vadose zone. Passive systems driven by wind or solar power are both more cost‐effective and sustainable than conventional systems. Such a passive system is being applied successfully to remediate a site impacted with total petroleum hydrocarbons (TPH) and benzene, toluene, ethylbenzene, and xylenes (BTEX) in soil. Bioventing technology was approved by the regulatory agency as an interim remedial action to remove chemicals of concern (COCs) in the vadose zone. A bioventing pilot study was conducted to evaluate the effectiveness of COC removal and collect parameters for full‐scale design and implementation. To evaluate the potential to use wind‐driven bioventing technology, two mobile weather stations were installed at the site and monitored for one month for a wind speed study. Based on the pilot‐test data and wind speed research, 12‐inch diameter funnel/vane 360‐degree wind collectors were designed as passive wind‐driven air‐injection devices and connected to existing monitoring wells. The measured air velocity ranged from 20 to 110 feet per minute during the start‐up and the first three months of operation and maintenance. Monitoring indicated a 20 percent oxygen delivery and greater than 90 percent reduction in COC concentrations, demonstrating a successful sustainable remediation with no power requirement and minimal operation and maintenance. © 2012 Wiley Periodicals, Inc.     

Before‐after control‐impact paired modeling of groundwater bentazon treatment at a phytoremediation site

A Before‐ After Control‐ Impact Paired (BACIP) model was used to evaluate the effectiveness of phytoremediation treatment on reduction of bentazon concentrations in shallow groundwater at a study site in Louisiana. Two different statistical approaches were made to evaluate the impact to this test site from the remediation program through time. Data were evaluated by Bayesian analysis of variance test methods. Data sets were unique in that the control data used for impact evaluation, as compared to before and after data, were compiled from groundwater upgradient monitoring wells existing prior to remediation. The statistical model supports the hypothesis that the phytoremediation program has positively impacted groundwater at the study site. © 2006 Wiley Periodicals, Inc.     

Modeling remediation time using natural attenuation at a dry‐cleaner site

Contaminants from dry‐cleaning sites, primarily tetrachloroethene (PCE), trichloroethene (TCE), cis‐dichloroethene (cis‐DCE), and vinyl chloride (VC), have become a major concern because of the limited funds and regulatory programs to address them. Thus, natural attenuation and its effectiveness for these sites needs to be evaluated as it might provide a less costly alternative to other remediation methods. In this research, data from a site in Texas were analyzed and modeled using the Biochlor analytical model to evaluate remediation times using natural attenuation. It was determined that while biodegradation and source decay were occurring at the site, the resulting attenuation rates were not adequate to achieve cleanup in a reasonable time frame without additional source remediation or control strategies. Cleanup times exceeded 100 years for all constituents at the site boundary and 800 years at the source for PCE, assuming cleanup levels of 0.005 mg/L for PCE and TCE and 0.07 mg/L and 0.002 mg/L for cis‐DCE and VC, respectively. © 2005 Wiley Periodicals, Inc.     

百菌清污染土壤生物修复研究进展

针对百菌清具有在土壤中药效稳定、不易分解、代谢周期长、长期大量施加导致土壤严重污染等特点和问题,简要介绍了百菌清的毒性作用机制。总结了降解土壤中百菌清的物理法、化学法和生物法的原理及优缺点。重点阐述了生物修复百菌清污染土壤的主要降解菌株及其效果、降解途径以及降解产物及其毒性,分析了土壤性质、微生物种类、温度、土壤含水率等因素对百菌清降解效果的影响。指出今后的研究重点应为降解中间产物的毒性分析及其进一步的降解与转化问题,而复合菌制剂或多酶复合体系可实现百菌清的彻底降解和无害化。     

Successful ISCR‐enhanced bioremediation of a TCE DNAPL source utilizing EHC® and KB‐1®

Remediation of chlorinated solvent DNAPL sites often meets with mixed results. This can be attributed to the diametrically opposed nature of the impacts, where the disparate dissolved‐phase plume is more manageable than the localized, high‐concentration source area. A wide range of technologies are available for downgradient plume management, but the relative mass of contaminants in a DNAPL source area generally requires treatment for such technologies to be effective over the long term. In many cases, the characteristics of DNAPL source zones (e.g., depth, soil heterogeneity, structural limitations) limit the available options. The following describes the successful full‐scale implementation of in situ chemical reduction (ISCR) enhanced bioremediation of a TCE DNAPL source zone. In this demonstration, concentrations of TCE were rapidly reduced to below the maximum contaminant level (MCL) in less than six months following implementation. The results described herein suggest that ISCR‐enhanced bioremediation is a viable remedial alternative for chlorinated solvent source zones. © 2010 Wiley Periodicals, Inc.     

The ART In‐Well Technology test at a chlorinated solvent site in central Iowa

An Accelerated Remediation Technologies (ART) In‐Well Technology pilot test was performed to evaluate the removal of chlorinated volatile organic compounds (VOCs) from groundwater. The ART In‐Well Technology was installed in one well located in the source area where dense nonaqueous‐phase liquid has been identified and VOC concentrations exceed 140,000 μg/L. Monitoring wells at the site were positioned between 10 and 170 feet from the ART test well. Overall, VOC concentrations from samples collected from the groundwater monitoring wells and in the vapors extracted for discharge from the ART treatment well were analyzed over the testing period. Monitoring results showed that concentrations of perchloroethylene were reduced in the closest monitoring well to nondetectable concentrations within 90 days. The cumulative removal of chlorinated VOCs from the ART test well over the six‐month pilot test period exceeded 9,500 pounds based on air monitoring data. The ART technology proved effective and cost‐efficient in reducing contaminant concentrations and removing a large mass of contamination from the subsurface in a short period of time. The radius of influence of the ART technology at the site was estimated to range between 65 and 170 feet. © 2007 Wiley Periodicals, Inc.     

PAH removal using soil and sediment washing at a contaminated harbor site

In tests conducted for the Canadian government on sediment from Thunder Bay Harbour, Ontario, the BioGenesis washing process was demonstrated to be effective in remediating contaminated harbor sediments. Removal efficiencies for 16 polyaromatic hydrocarbons (PAHs) in concentrations exceeding 4,000 parts per million averaged 90 to 95 percent in pilot tests. These results are significant because, until now, washing processes have not proven effective in cleaning the small-size particles of silt and clay that make up most underwater sediments. In Thunder Bay, 81 percent of the particles were less than 38 microns (medium silt) in size. The tests on Thunder Bay sediment were conducted under the auspices of the Contaminated Sediment Treatment Technology Program of Environment Canada's Wastewater Technology Centre. Thunder Bay Harbour is one of 43 “areas of concern” identified by the International Joint Commission of Great Lakes Water Quality.