Triad case study: Former small arms training range

The U.S. Army Corps of Engineers (US ACE) used the Triad approach to expedite site characterization of contaminated soil at the Former Small Arms Evergreen Infiltration Training Range in Fort Lewis, Washington. The characterization was designed to determine if surface soils contain significant concentrations of metals, with the focus on collecting sufficient data for determining appropriate future actions (i.e., risk analysis or soil remediation). A dynamic sampling and analytical strategy based on rapid field‐based analytical methods was created in order to streamline site activities and save resources while increasing confidence in remediation decisions. Concurrent analysis of soil samples during the demonstration of method applicability (DMA) used both field portable X‐ray fluorescence (FPXRF) and laboratory methodologies to establish a correlation between FPXRF and laboratory data. Immediately following the DMA, contaminated soil from the impact berm was delineated by collecting both FPXRF data and fixed laboratory confirmation samples. The combined data set provided analytical results that allowed for revisions to the conceptual site model for the range and directed additional sample collection activities to more clearly determine the extent and distribution of soil contamination. © 2004 Wiley Periodicals, Inc.     

Arsenic and thallium data in environmental samples: Fact or fiction?

Matrix effects may increasingly lead to erroneous environmental decisions as regulatory limits or risk‐based concentrations of concern for trace metals move lower toward the limits of analytical detection. A U.S. Environmental Protection Agency Office of Technical Standards Alert estimated that environmental data reported using inductively coupled plasma spectrometry (ICP‐AES) has a false‐positive rate for thallium of 99.9 percent and for arsenic of 25 to 50 percent. Although this does not seem to be widely known in the environmental community, using three case studies, this article presents data in environmental samples that demonstrate severe matrix effects on the accuracy of arsenic and thallium results. Case Study 1 involves soil results with concentrations that approached or exceeded the applicable regulatory soil cleanup objectives of 13 mg/kg for arsenic and 2 mg/kg for thallium. Reanalysis using ICP coupled with a mass spectrometer (ICP‐MS) confirmed all thallium results were false positives and all arsenic results were biased high, concluding no action was required for soil remediation. Case Study 2 involves groundwater results for thallium at a Superfund site, where thallium was detected in groundwater up to 21.6 μ g/L using ICP‐AES. Reanalysis by ICP‐MS reported thallium as nondetect below the applicable regulatory level in all samples. ICP‐MS is usually a more definitive and accurate method of analysis compared to ICP‐AES; however, this is not always the case, as we demonstrate in Case Study 3, using data from groundwater samples at an industrial site. Through a weight‐of‐evidence approach, it is demonstrated that although method quality control results were acceptable, interferences in some groundwater samples caused biased high results for arsenic using ICP‐MS, which were significantly lower when reanalyzed using hydride generation atomic fluorescence spectrometry. Causes of these interference effects and conclusions from the three case studies to obtain accurate metal data for site assessment, risk characterization, and remedy selection are discussed. © 2010 Wiley Periodicals, Inc.     

Laboratory validation study of new vapor‐phase‐based approach for groundwater monitoring

Recent improvements in field‐portable analytical equipment allow accurate on‐site measurement of VOCs present in air at concentrations of less than 0.1 parts per million volume (ppmv). The objective of this project is to determine if the use of these instruments for vapor‐phase measurements of headspace in a monitoring well can serve as a reliable and accurate method for monitoring volatile organic compound (VOC) concentrations in groundwater under equilibrium conditions. As part of a comprehensive research project investigating the utility of this proposed monitoring method, the authors have completed a laboratory validation study to identify instruments and sample‐collection methods that will provide accurate measurement of VOC concentrations in groundwater. This laboratory validation study identified two field‐portable instruments (a gas chromatograph and a photoionization detector) with sufficient sensitivity to measure VOCs in groundwater at concentrations below typical monitoring standards (i.e., 1 to 5 μg/L). The accuracy and precision of these field instruments was sufficient to satisfy typical data‐quality objectives for laboratory‐based analysis. In addition, two sample‐collection methods were identified that yield vapor‐phase samples in equilibrium with water: direct headspace sampling and passive diffusion samplers. These sample‐collection methods allow the field instruments (which measure VOC concentrations in vapor‐phase samples) to be used to measure VOC concentrations in water. After further validation of these sample‐collection methods in the field, this monitoring method will provide a simple way to obtain accurate real‐time measurements of VOC concentrations in groundwater using inexpensive field‐portable analytical instruments. © 2009 Wiley Periodicals, Inc.     

Modified Fenton's processes for effective in‐situ chemical oxidation—Laboratory and field evaluation

Fenton's reagent in its conventional form, although effective for contaminant treatment, is impractical from an in‐situ field application perspective due to low pH requirements (i.e., pH 3‐4), and limited reagent mobility when introduced into the subsurface. Modified Fenton's processes that use chelated‐iron catalysts and stabilized hydrogen peroxide have been developed with the goal of promoting effective in‐situ field application under native pH conditions (i.e., pH 5‐7), while extending the longevity of hydrogen peroxide. Laboratory experiments conducted in soil columns packed with organic soil to compare modified Fenton's catalysts with conventional catalysts (acidified iron [II]) indicated superior mobility and sorption characteristics for modified Fenton's catalysts. Furthermore, the acidic pH of a conventional catalyst was buffered to the native soil range, leading to increased iron precipitation/adsorption following permeation through the soil column. The chelates present within the modified Fenton's catalyst showed greater affinity toward iron compared with the native soil and, hence, minimized iron loss through adsorption during the permeation process even at pH 5‐7. Field effectiveness of the modified Fenton's process was demonstrated at a former dry‐cleaning facility located in northeast Florida. Preliminary laboratory‐scale experiments were conducted on soil‐slurry and groundwater samples to test the process efficacy for remediation of chlorinated solvents. Based on successful experimental results that indicated a 94 percent (soil slurry) to 99 percent (groundwater) reduction of cis‐1,2‐DCE, PCE, and TCE, a field‐scale treatment program was initiated utilizing a plurality of dual‐zone direct push injection points installed in a grid fashion throughout the site. Results of treatment indicated a 72 percent reduction in total chlorinated contamination detected in the site groundwater following the first injection event; the reduction increased to 90 percent following the second injection event. © 2002 Wiley Periodicals Inc.     

Passive to active tie‐in for soil gas surveys: Improved technique for source‐area,spatial variability,remediation‐monitoring,and vapor‐intrusion assessment

The mass‐to‐concentration tie‐in (MtoC Tie‐In) correlates passive soil gas (PSG) data in mass to active soil gas data in concentration determined by the US EPA Method TO‐17 or TO‐15. Passive soil gas surveys consist of rapid deployment of hydrophobic sorbents (dozens to several hundred locations typically installed in one day) to a depth of six inches to three feet in a grid pattern with exposure in the field from three days to two weeks to target a wide variety of organic compounds. A power function is used on a compound‐to‐compound basis to correlate spatially varying mass (nanograms) from selected locations within a passive soil gas survey to concentration (µg/m³) at those same locations. The correlation from selected PSG locations is applied to the remainder of the PSG grid. The MtoC Tie‐In correlations provide added value to a PSG survey, with the PSG data then used to estimate risk throughout the limits of the investigation for quantitative assessment. The results from a site in northern California show the MtoC Tie‐In correlations for both benzene and total petroleum hydrocarbons (TPH). The correlations are applied on a compound‐to‐compound basis to the remaining locations in the PSG grid to provide an estimate of concentration that can be used for comparison to risk/screening levels or fate‐and‐transport diagnostic tools (partitioning equations, solubility laws, etc.). An example of how the correlations are applied is presented in tabular form. The results from a chlorinated solvent survey show the MtoC Tie‐In correlation from a site in Maryland for tetrachloroethene (PCE). In this instance, there was a near‐perfect relationship between the PSG mass and the active soil gas concentration (R² value of 1). The concentration estimated throughout a PSG grid enables a vast new realm of interpretive power at sites. Several other sites are discussed, including an example application for groundwater. © 2009 Wiley Periodicals, Inc.     

Evaluation of a soil‐amendment process demonstration for reducing the bioavailability of lead

The U.S. Environmental Protection Agency (EPA) evaluated an in‐situ application of a soil‐amendment process at a residential site that was contaminated with lead. The goal of the evaluation was to determine if the soil‐amendment process resulted in lower concentrations of bioavailable lead in the contaminated soils. The relative bioavailability of lead (bioaccessible lead) was measured by an in vitro test procedure that uses a highly acidic extraction procedure to simulate human digestive processes. The soil‐amendment demonstration showed that the 11.2 percent mean reduction in bioavailable lead concentration between untreated and treated soils was not statistically different. © 2002 Wiley Periodicals, Inc.     

Use of a novel biomarker,botryococcane, to monitor biodegradation of two lacustrine‐sourced crude oils

Bioremediation is a proven alternative for remediating petroleum‐impacted soils at exploration and production (E&P) sites. Monitoring remediation performance can involve detection and quantification of biodegradation resistant compounds such as C₃₀17α(H),21β(H)‐hopane, which requires the use of gas chromatography with mass spectrometry detection (GC/MS). Due to the remoteness of many E&P sites, this technology is not always available, and alternative methods are needed to provide reliable quantitative measurements of petroleum remediation efficiency. This study provides a detailed chemical characterization of lacustrine‐sourced crude oils and a technical basis for measuring the effectiveness of bioremediation efforts for soil impacted by those crudes. We show that the novel isoprenoid hydrocarbon botryococcane is relatively stable in lacustrine‐sourced crude oils compared with C₃₀17α(H),21β(H)‐hopane under moderate biodegradation conditions generally observed in field samples. We have also demonstrated that, due to the stability and relatively elevated concentration of botryococcane in lacustrine oils, it can be reliably measured using the more cost‐effective and available GC/FID methodology, and thereby be used to monitor the progress of ongoing soil bioremediation activities at remote sites.     

An application of a phytoremediation technology in Bulgaria—The Kremikovtzi Steel Works experiment

The first in‐field phytoremediation trial in Bulgaria was initiated in the summer of 1998 at two highly polluted heavy‐metal sites within the industrial region of Kremikovtzi Steel Works, near the capital town of Sofia. The experiment targeted phytoextraction of lead, according to the selection of Brassica juncea seed material and technology, generously provided by Phytotech, Inc. The metal concentrations in soil samples were measured before planting and after harvest. Leaf and stem plant samples were investigated by laser mass spectrometry in search of metal accumulation depots. The results of the one‐planting experiment show a very uneven decrease between 0 and 25.9 percent of the initial lead concentration at various sample locations. The trial, which was initially planned for three consecutive years, was unfortunately terminated in the second year because the Steel Works entered a privatization procedure. Nevertheless, the experimental data obtained confirmed the general applicability of phytoremediation to treat soil polluted with heavy metals. The experiment was further successful, because it confirmed the proposal to clean the three‐kilometer ecological zone around the Steel Works with two plantings per year in two years to levels below the maximum permissible level for lead of 25 to 80 g/t for pH 4, according to the Bulgarian Environmental Standards. © 2006 Wiley Periodicals, Inc.     

Field and laboratory evaluation of the treatment of DNAPL source zones using emulsified zero‐valent iron

Emulsified zero‐valent iron (EZVI) is a surfactant‐stabilized, biodegradable emulsion that forms droplets consisting of a liquid‐oil membrane surrounding zero‐valent iron (ZVI) particles in water. This article summarizes the results obtained during the first field‐scale deployment of EZVI at NASA's Launch Complex 34 (LC34) located on Cape Canaveral Air Force Station, Florida, in August 2002 and presents the results of recent follow‐on laboratory tests evaluating the mechanisms, which contribute to the performance of the technology. The field‐scale demonstration evaluated the performance of EZVI containing nanoscale zero‐valent iron (NZVI) when applied to dense, nonaqueous phase liquid (DNAPL) trichloroethylene (TCE) in the saturated zone. Results of the field demonstration indicate substantial reductions in TCE soil concentrations (greater than 80 percent) at all but two soil boring locations and significant reductions in TCE groundwater concentrations (e.g., 60 percent to 100 percent) at all depths targeted with EZVI. Laboratory tests conducted in 2005 suggest that both NZVI particles and EZVI containing NZVI can provide significant reductions in TCE mass when used to treat TCE DNAPL in small test reactors. However, EZVI was able to reduce TCE concentrations to lower levels than were obtained with NZVI alone, likely as a result of the combined impact of sequestration of the TCE into the oil phase and degradation of the TCE with the NZVI. © 2006 Wiley Periodicals, Inc.     

In Situ Remediation of 1,4‐Dioxane Using Electrical Resistance Heating

Recent regulatory changes need more challenging treatment goals for 1,4‐dioxane. However, significant treatment limitations exist in part due to the high solubility and low Henry's law constant of 1,4‐dioxane. Two case studies are reported with substantial 1,4‐dioxane concentration reductions through in situ thermal remediation via electrical resistance heating (ERH). Concentration reductions greater than 99.8 percent of 1,4‐dioxane have been observed in the field using ERH. Concentrations of 1,4‐dioxane in air and steam extracted by an ERH vapor recovery system have also been evaluated. Laboratory studies were conducted to further understand the mechanisms that enable ERH remediation of 1,4‐dioxane. Vapor liquid equilibrium studies in water and soil were conducted and utilized to develop an ERH treatment cost model for 1,4‐dioxane. Existing field data were correlated to the 1,4‐dioxane treatment cost model. Field observations and laboratory testing indicate steam stripping that occurs through ERH remediation is an effective treatment method for 1,4‐dioxane. ©2015 Wiley Periodicals, Inc.     

Solvent extraction and soil washing treatment of contaminated soils from wood preserving sites: Bench‐scale studies

Bench‐scale solvent extraction and soil washing studies were performed on soil samples obtained from three abandoned wood preserving sites included in the National Priority List. The soil samples from these sites were contaminated with high levels of polyaromatic hydrocarbons (PAHs), pentachlorophenol (PCP), dioxins, and heavy metals. The effectiveness of the solvent extraction process was assessed using liquefied propane or dimethyl ether as solvents over a range of operating conditions. These studies have demonstrated that a two‐stage solvent extraction process using dimethyl ether as a solvent at a ratio of 1.61 per kg of soil could decrease dioxin levels in the soil by 93.0 to 98.9 percent, and PCP levels by 95.1 percent. Reduction percentages for benzo(a)pyrene (BaP) potency estimate and total detected PAHs were 82.4 and 98.6 percent, respectively. Metals concentrations were not reduced by the solvent extraction treatment. These removal levels could be significantly improved using a multistage extraction system. Commercial scale solvent extraction using liquefied gases costs about $220 per ton of contaminated soil. However, field application of this technology at the United Creosote site, Conroe, Texas, failed to perform to the level observed at bench scale due to the excessive foaming and air emission problem. Soil washing using surfactant solution and wet screening treatability studies were also performed on the soil samples in order to assess remediation strategies for sites. Although aqueous phase solubility of contaminants seemed to be the most important factor affecting removal of contaminants from soil, surfactant solutions (3 percent by weight) having nonionic surfactants with hydrophile‐lipophile balance (HLB) of about 14 (Makon‐12 and Igepal CA 720) reduced the PAH levels by an average of 71 percent, compared to no measurable change when pure deionized water was used. Large fractioza of clay and silt (<0.06mm), high le!ezielsof orgaizic contami‐ nants and hzimic acid can makesoil washing less applicable.     

Leaching assessment of road materials containing primary lead and zinc slags

Characterisation of the leaching behaviour of waste-containing materials is a crucial step in the environmental assessment for reuse scenarios. In our research we applied the multi-step European methodology ENV 12-920 to the leaching assessment of road materials containing metallurgical slag. A Zn slag from an imperial smelting furnace (ISF) and a Pb slag from a lead blast furnace (LBF) are investigated. The two slags contain up to 11.2 wt% of lead and 3.5 wt% of zinc and were introduced as a partial substitute for sand in two road materials, namely sand-cement and sand-bitumen. At the laboratory scale, a leaching assessment was performed first through batch equilibrium leaching tests. Second, the release rate of the contaminants was evaluated using saturated leaching tests on monolithic material. Third, laboratory tests were conducted on monolithic samples under intermittent wetting conditions. Pilot-scale tests were conducted for field testing of intermittent wetting conditions. The results show that the release of Pb and Zn from the materials in a saturated scenario was controlled by the pH of the leachates. For the intermittent wetting conditions, an additional factor, blocking of the pores by precipitation during the drying phase is proposed. Pilot-scale leaching behaviour only partially matched with the laboratory-scale test results: new mass transfer mechanisms and adapted laboratory leaching tests are discussed.     

Evaluation of white‐rot fungi for the remediation of creosote‐contaminated soil

Application of fungal‐based bioaugmentation was evaluated for the remediation of creosote‐contaminated soil at a wood‐preserving site in West Virginia. Soil at the site contained creosote‐range polycyclic aromatic hydrocarbons (PAHs) at concentrations in some areas that exceed industrial risk‐based levels. Two white‐rot fungi (Pleurotus ostreatus and Irpex lacteus) were evaluated for remediation effectiveness in a two‐month bench‐scale treatability test. Both fungi produced similar results, with up to 67.3 percent degradation of total PAHs in 56 days. Pilot‐scale testing was performed at the site using Pleurotus ostreatus grown on two local substrate mixtures. During the 276‐day field trial, total PAHs were degraded by up to 93.2 percent, with all individual PAHs except one achieving industrial risk‐based concentrations. It was recommended that fungal‐based remediation be applied to all contaminated soil at the site. © 2002 Wiley Periodicals, Inc.     

Mineralization of Poly(ɛ-caprolactone)/Adipate Modified Starch Blend in Agricultural Soil

The biodegradability properties of poly(ɛ-caprolactone) (PCL) and modified adipate-starch (AS) blends, using Edenol-3203 (E) as a starch plasticizer, were investigated in laboratory by burial tests of the samples in previously analyzed agricultural soil. The biodegradation process was carried out using the respirometric test according to ASTM D 5988-96, and the mineralization was followed by both variables such as carbon dioxide evolution and mass loss. The results indicated that the presence of AS-E accelerated the biodegradation rate as expected.     

Cement‐based solidification/stabilization of phenol‐contaminated soil by bentonite and organophilic clay

The performance of ordinary and organophilic clays in the solidification and stabilization process was investigated with respect to the unconfined compressive strength (UCS) and leaching of phenol‐contaminated soil. The samples contained 2,000 mg/kg of phenol. White cement (15 and 30 percent by weight [wt%]) was used as binder, while ordinary and organophilic clays (8, 15, and 30 wt%) were applied as additives for reducing the harmful effects of phenol interference in cement hydration with a 28‐day curing time. The results revealed that the UCS is reduced by increasing the amount of clays. The values of UCS of all samples met the minimum standards specified for disposal in sanitary landfills determined by developed countries. The leaching test demonstrated that the degree of leaching diminished with increased clay content in all samples of both clay types. This reduction was observed to be greater in samples containing organophilic clay than in bentonite clay samples. Furthermore, the best composition of the materials tested was determined to be 30 wt% white cement plus 13.3 wt% organophilic clay with a compressive strength of 3,839 kPa, phenol removal percentage of 80 percent, and a cost of $67 per ton of contaminated soil.     

Case study of testing heavy‐particle concentrator‐aided remediation of lead‐contaminated rifle shooting range soil

Trials were conducted to optimize the parameters of a heavy‐particle concentrator (HPC) for the remediation of soil stockpiles contaminated by metallic lead at the Mount Stuart training area in Townsville, Queensland, Australia. A range of treatment methods, including orbital screen, HPC, and a combination of orbital screen and HPC were evaluated. The treatment efficiency, as well as reductions in Pb and Australian Standard Teaching Procedure values, was ranked: Orbital screen + HPC < HPC < 2nd run through HPC. The combination of orbital screening, HPC, and phosphate‐aided immobilization completely remediated the stockpiled material by reducing total lead to below the Australian National Environmental Protection Measure Health Investigation Level for Soil Contaminant (Recreational; < 600 milligrams lead per kilogram). The optimized parameters of HPC at 4 tonnes per hour of the < 40 millimeter (mm) orbital screen feed fraction were: inclination angle 4°, trommel speed 1,860 revolutions per minute (rpm), HPC belt speed 3.5 rpm, material distribution chute extension 100 mm and water flow 480 liters per minute.     

Two‐dimensional transport of lactate‐modified nanoscale iron particles in porous media

This study investigates the two‐dimensional transport of nanoscale iron particles (NIP) and lactate‐modified NIP (LMNIP) in homogeneous and heterogeneous porous media under typical pressurized groundwater flow conditions. A two‐dimensional bench‐scale test setup was developed and a series of experiments was conducted simulating homogeneous sand profile and two‐layer profile with two different sands. NIP and LMNIP at a concentration of 4 g/L were prepared in electrolyte simulating groundwater conditions and were injected at the inlet of the test setup under different pressure gradients (0.5. 0.8, 1, and 2 pounds per square inch). During the testing, effluent was collected and its volume and nanoiron concentrations were measured. At the end of the testing, soil cores were obtained at different distances from the inlet and were used to measure nanoiron concentrations and magnetic susceptibility values. Results showed that the transport of NIP and LMNIP was enhanced by increased pressure gradient. LMNIP transport occurred more uniformly as compared to bare NIP. The iron concentrations decreased with distance from the inlet to the outlet and increased from the top to the bottom of the test cell. The data indicate that, as the particles were transported, they underwent aggregation and sedimentation, which resulted in the observed non‐uniform spatial distribution of iron. The NIP and LMNIP transported through the high‐porosity and high‐permeability soil layer in the heterogeneous soil profile, implying that the transport occurred predominantly along the path of least resistance for the flow. Magnetic susceptibility values are found to have good correlation with the iron content in the soil and are helpful to characterize the transport of NIP and LMNIP. Overall, this study shows that the non‐uniform distribution of NIP and LMNIP occurs under two‐dimensional transport conditions and the soil heterogeneities can significantly impact the transport of NIP and LMNIP. The design of field delivery systems should consider such conditions and optimize the pressurized injection systems. © 2011 Wiley Periodicals, Inc.     

Ex‐situ efficacy analysis of brine remediation products in clay loam soil

This study evaluated the effectiveness of gypsum and three proprietary products to remediate brine‐contaminated soil. The research objective was to determine if additives could increase plant cover germination in soils without costly prior soil‐washing or dilution techniques. The soil was shredded using a soil shredder equipped with a spray bar to apply the individual treatments of DeSalt Plus, SoilTech, Chlor*rid, and calcium sulfate (gypsum). Treatments were placed in 40‐mm high‐density polyethylene cells and small drainage systems were installed to allow removal of excess water. An initial 10‐point soil composite was taken from bulk untreated soils at a depth of more than 2.5 cm. Five‐point composite samples were collected from the same depth at weekly intervals and analyzed for: electrical conductivity, sodium adsorption ratio, cation exchange capacity, sodium, calcium, magnesium, potassium, chlorides, and pH. The Gapon selectivity coefficient was calculated and utilized to quantify the affinity for binding between ionic alkali salt constituent groups Na⁺, Ca ⁺⁺, and Mg ^++. Soil analysis indicated product‐related improvements in and bioavailability of salts. The nature of the products requires some prior treatment such as soil washing or dilution using clean soil to lower electroconductivity levels and allow the site to vegetate.     

The Use of Zero‐Valent Iron (ZVI) Technology to Promote DDT and Dieldrin Degradation at Point Pelee National Park

Point Pelee National Park (PPNP) is highly contaminated with dichlorodiphenyltrichloroethane (DDT) and dieldrin due to the historical use of these two persistent organochlorine pesticides. Zero‐valent iron (ZVI) technology with and without amendments has been successfully used in the past to promote organochlorine pesticides degradation in several locations in North America and Europe. In this study, the use of two commercially available ZVI products, DARAMEND^® and EHC^®, to promote DDT and dieldrin degradation in PPNP's soil and groundwater were investigated. DARAMEND^® was applied to PPNP's soil in a laboratory experiment and in an in situ pilot‐scale plot. In both cases, DARAMEND^® did not significantly increase DDT or dieldrin degradation in treated soils. The effectiveness of EHC^® was tested in a laboratory experiment that simulated the park's groundwater environment using PPNP's pesticide contaminated soil. The result was consistent with the one reported for DARAMEND^®, in that there was no significant increase in DDT or dieldrin degradation in any of the samples treated with EHC^®. These results demonstrate that both of these ZVI commercially available products are not suitable for in situ remediation at PPNP.  ©2017 Wiley Periodicals, Inc.     

Phytoremediation of industrial sludge using vegetation‐assisted dewatering

With the emergence of risk‐based corrective action decisions, there is interest in the use of more natural techniques that may be as protective as the traditional removal, landfill, or capping approaches for impoundment closure. The use of phytoremediation is one of the more promising techniques. This article presents the results of a three‐year field‐pilot phytoremediation study that involved the use of plants to enhance sludge dewatering at an inactive natural gas‐cracking wastewater lagoon. The dewatering was accompanied by contaminant reduction of benzene, toluene, xylene (BTX), and naphthalene concentrations to below the cleanup goals. Meanwhile, the concentration reductions of three or more ring polynuclear aromatic hydrocarbons (PAHs) varied between 30 percent and 60 percent, except for dibenz[a,h]anthracene. The residual PAHs in the sludge are not leaching. Parallel laboratory studies suggest a reduced PAH availability and mobility in the unsaturated zone sludge. © 2002 Wiley Periodicals, Inc.