城市下水污泥焚烧过程中二次污染物排放特性的试验研究

在0．15MWt循环流化床燃烧试验台上进行了城市下水污泥与煤的混烧试验，分析了烟气中的二次污染物排放特性。分析结果表明，利用循环流化床焚烧城市下水污泥时，添加辅助燃料（如煤）及改变焚烧条件，不仅可以达到稳定燃烧的目的，而且有利于抑制焚烧中二次污染物（如CO及二恶英等有机污染物）的生成。分析了焚烧污泥污染物的排放特性。为采用焚烧方式处理城市下水污泥提供了基础性试验数据。     

油田油泥与煤在流化床中的混烧

基于小型流化床焚烧实验平台,通过含油污泥与煤混合燃烧,分析气体污染物排放浓度以及灰渣特性。含油污泥与煤混烧后NO_x、SO_2的排放浓度均低于危险废物焚烧排放标准。根据灰渣中组分分析,煤中碱金属化合物能抑制SO_2的排放。渣样的浸出毒性均在标准范围内,灰样的浸出毒性高于渣样,主要因为飞灰中更容易富集挥发和易溶形态的重金属。基于小试实验的结果,油泥在小型流化床上的燃烧不充分导致了CO排放浓度较高,且灰的灼减率较高,因此,在后续中试以及示范工程中,应保证油泥的充分燃烧,为灰渣的综合利用提供理论基础。     

火电厂协同资源化处理城市污泥二次污染控制

控制循环流化床锅炉掺烧城市污泥二次污染物的排放,实现污泥的减量化、无害化处置和资源化利用。方法:利用循环流化床锅炉烟气余热干燥污泥,干化污泥与燃煤掺配燃烧,污泥干燥系统与锅炉DCS控制系统对接,依据机组负荷自动化控制锅炉耗煤量、床温和污泥给入量等运行参数,有效抑制二恶英的形成。结果表明,污泥自动化掺烧系统投运后,烟气中二恶英的排放浓度小时均值不高于0.011 0 ng TEQ·(Nm)-3,飞灰中二恶英含量不高于2.802 2 ng TEQ·kg-1、底渣中二恶英含量不高于0.659 6 ng TEQ·kg-1,符合国家污染控制标准要求。火电厂协同资源化处理城市污泥过程中,污泥自动化掺烧系统投运能够有效控制二次污染物的排放,实现了城市污泥的减量化、无害化处置和资源化利用。     

循环流化床锅炉燃烧城市生活垃圾的研究进展

城市生活垃圾(MSW)产量的与日俱增及环保要求的不断提高,使循环流化床(CFB)燃烧技术逐渐在MSW的回收和利用方面扮演越来越重要的角色.简要分析了国内外采用分类回收及综合利用、卫生填埋、堆肥和一般焚烧方法处理MSW的不足之处以及采用CFB燃烧技术的优越性,重点介绍了国内外采用CFB燃烧装置焚烧MSW的研究和应用现状,指出了目前存在的问题及努力的方向.采用CFB燃烧装置焚烧MSW关于SO2、NOx、CO排放的实验研究和运行结果令人满意,但对HCl、二恶英及重金属排放还需要进一步研究.试验及实际运行结果都表明,采用CFB燃烧装置对MSW进行焚烧处理是切实可行的,它将是未来解决MSW问题的重要手段.     

污水处理厂污泥干化焚烧处理可行性分析

以绍兴污水处理厂脱水污泥为研究对象,通过实验分析了污泥进行干化焚烧处理的可行性。对污泥泥质进行分析,采用桨叶式污泥干化机对污泥的热干化特性、干化过程污染排放特性进行研究,使用流化床污泥焚烧试验装置对污泥焚烧工况及焚烧过程中污染物的排放特征进行研究,结果表明,绍兴污水处理厂脱水污泥的泥质特征与大多数污水污泥类似,灰分较高、发热量较低,需干化后才可实现稳定燃烧;污泥在小型桨叶式污泥干化机内的干化速率最高达到0.6kg/(m2·min),并随污泥干化的进行而逐渐降低;干化过程产生的常规污染气体中氨气浓度最高,可达170 mg/Nm3;污泥干化冷凝水的COD高达820 mg/L,氨氮等指标也很高。污泥干化系统的设计需充分考虑污泥热干化过程中气体和液体污染物的排放,设置相应的处理设施。污泥干化至含水率30%时,可在不投加辅助燃料的情况下实现流化床焚烧炉内的焚烧处理,干化污泥焚烧时需关注烟气中常规污染气体和重金属的控制,焚烧灰渣浸出毒性未超过国标限值。     

印染污泥与煤在循环流化床上混烧实验

印染污泥热值较低,直接燃烧较为困难,需要添加辅助燃料进行混燃.通过对印染污泥与煤在循环流化床中混烧实验研究,发现印染污泥着火特性较差,启动时需将炉温提升至800℃以上,加入的污泥才能进行燃烧;污泥与煤在循环流化床中可以实现充分燃烧,温度在800～900℃之间均匀稳定,燃烧效率超过95%;混烧工况下烟气SO2含量高,在炉...     

广西城镇污泥掺烧利用组分特性的分析

对广西城镇污水处理厂污泥进行元素分析、组分分析、工业分析和热重分析,探讨污泥掺烧应用特性,为广西的污泥资源化利用提供数据。结果表明,污泥的元素组成与煤差别较大,如污泥中的氮元素含量为4.627%,高于煤的1.628%;污泥焚烧灰含有高达15%的Si O2;污泥的挥发分为34.6377%比煤的25.089%略高;污泥的焚烧可分为3个阶段,分别为水分析出阶段(室温~160℃)、挥发分析出燃烧阶段(160~500℃)、固定碳及剩余可燃物燃烧阶段(510~950℃),升温速率升高,挥发分析出阶段提前了约50℃,粒径对析出温度影响不大,但粒径小更利于干污泥燃烧。因此,广西污泥是一种低热值,燃烧剧烈的燃料,可以用于掺烧,焚烧灰分具有较高的建材价值。     

不同城市生活垃圾焚烧技术的综合评价

通过工程的经济性分析、工艺过程的能流分析以及工程的环境影响分析,综合分析了流化床、炉排炉、气化熔融和等离子体气化等不同城市生活垃圾焚烧技术。结果表明:(1)在零补贴的情况下,流化床焚烧技术的工程效益最佳,但从项目投产年算起,其投资回收期也需9年;炉排炉、气化熔融与等离子体气化焚烧技术要达到流化床焚烧技术零补贴情况下的经济效益,分别需补贴约70、140、500元/t。(2)各城市生活垃圾焚烧技术下区域的水体富营养化和全球变暖影响最显著,而人体毒性影响最小。气化熔融焚烧技术和等离子体气化焚烧技术的环境影响比其他两种焚烧技术小一个数量级。(3)考虑污染物排放的环境效益,在现行中国排放标准下,流化床、炉排炉与气化熔融焚烧技术的工程效益都将得到较大提升。随着排放标准的更加严格,流化床焚烧技术的年收益率下降最显著;气化熔融焚烧技术的工程效益相较最优。     

循环流化床锅炉燃烧城市生活垃圾的研究进展

城市生活垃圾（MSW）产量的与日俱增及环保要求的不断提高，使循环流化床（CFB）燃烧技术逐渐在MSW的回收和利用方面扮演越来越重要的角色。简要分析了国内外采用分类回收及综合利用、卫生填埋、堆肥和一般焚烧方法处理MSW的不足之处以及采用CFB燃烧技术的优越性，重点介绍了国内外采用CFB燃烧装置焚烧MSW的研究和应用现状，指出了目前存在的问题及努力的方向。采用CFB燃烧装置焚烧MSW关于SO２、NOx、CO排放的实验研究和运行结果令人满意，但对HCl、二恶英及重金属排放还需要进一步研究。试验及实际运行结果都表明，采用CFB燃烧装置对MSW进行焚烧处理是切实可行的，它将是未来解决MSW问题的重要手段。     

污泥热干化和燃烧特性试验研究

分别在桨叶式干化机和热重仪上进行污泥干化和燃烧试验,研究了污泥干化特性和污染物排放特性,并对污泥的燃烧特性进行分析。结果表明,污泥干化过程分为黏稠区、粘滞区和颗粒区3个阶段。干化过程排放的污染气体有氨气、氯化氢、氟化氢、氰化氢、甲烷和挥发性有机酸等,其中氨气为主要污染气体。经冷凝吸收和活性炭吸附处理后,各种污染气体浓度均显著降低,其中氨气去除率最高,达97.04%。污泥干化冷凝液的BOD5和COD质量浓度分别为4 040、8 510mg/L,氨氮的质量浓度为1 025mg/L,pH为9.84,属于高浓度有机废水。污泥的燃烧过程可以分为3个失重阶段:水分析出阶段(50～150℃),挥发分燃烧阶段(150～450℃),固定碳燃烧阶段(450～650℃)。分别用Kissinger法和Ozawa法计算挥发分燃烧阶段和固定碳燃烧阶段的活化能和动力学方程,挥发分燃烧阶段的活化能低于固定碳燃烧阶段,表明挥发分燃烧阶段污泥更易燃烧。污泥的燃烧过程在650℃时基本完成,因此实际工程应用中,设计干化污泥的焚烧温度在750℃比较合理。     

PCDD/F, PAH and heavy metals in the sewage sludge from six wastewater treatment plants in Beijing, China

In order to better understand land application of sewage sludge, the characterization of heavy metals, PCDD/F and PAHs in sewage sludge was investigated from six different wastewater treatment plants (WWTP) in Beijing City, China. It was found that the total concentrations of Zn in Wujiacun (WJC) sewage sludge, and Cd and Hg in sewage sludge generated from all of the six different places are higher than Chinese regulation limit of pollutants for sludge to be used for agriculture (GB18918-2002). The levels of 16 PAHs that have been categorized as priority pollutants by US EPA in the sewage sludge samples varied from 2467 to 25923 microg/kg (dry weight), the highest values of 25923 microg/kg being found in WJC WWTP. The concentrations of Benzo[a]pyrene were as high as 6.1mg/kg dry weight in WJC sewage sludge, exceeding the maximum permitted content by GB18918-2002. Individual PAH content varies considerably with sewage samples. The ratios of anthracene to anthracene plus phenanthrene (An/178), benz[a]anthracene to benz[a]anthracene plus chrysene (BaA/228), indene[1,2,3-cd]pyrene to indene[1,2,3-cd]pyrene plus benzo[g,h,i]perylene (In/In+BP), and fluoranthene to fluoranthene plus pyrene (Fl/Fl+Py) suggest that petroleum and combustion of fossil fuel were the dominant contributions for the PAHs in sewage sludge. The concentrations of total PCDD/F in the sewage sludge ranged from 330 to 4245 pg/g d.w. The toxicity equivalent concentrations is between 3.47-88.24 pg I-TEQ according to NATO/CCMS, which is below Chinese legislation limit value proposed for land application. The PCDD/F congener/homologue profiles found in the Beijing samples indicated that the high chlorinated PCDD/F contamination might originate mainly from PCP-related source and depositional sources while the low chlorinated PCDD/F homologues could be originating from incineration or coal combustion. The major source of PCDD/Fs in Beijing sludge is still unclear.     

Characteristics of leachate from pyrolysis residue of sewage sludge

The pyrolysis residue (SP) of sewage sludge (SS) produced at 500 degrees C was subjected to batch and column leaching tests to investigate the release of its organic and inorganic constituents and metals. For comparison, incineration ash (SI) obtained from a SS incinerator was also tested. Pyrolysis and incineration reduced organic matter of SS from 0.78 kg kg(-1)-dry SS to 0.16 and 0.01 kg kg(-1)-dry SS, respectively. Heavy metals remained in SP without being volatilized, although Cd and Pb were transferred into the off-gas during incineration. In the batch leaching test with the leaching liquid-to-solid mass ratio (L/S)=10, the pH of the SS, SP, and SI filtrates was 6.3, 7.9, and 11.0, respectively. The total organic carbon concentrations were in the order SS (877 l mg l(-1))>SP (99 mg l(-1))>SI (26 mg l(-1)). The SP and SI filtrates met the landfill standard for the Cd and Pb concentrations (<0.3 mg l(-1)). In the column tests, although the SP contained more organic matter than that of SI, its carbon discharge into the leachate under aerobic conditions was similar to that of SI under anaerobic conditions. The leaching of heavy metals, such as Cd, Cr, Pb, and Zn, was also suppressed in SP during the active decomposition of organic matter. We demonstrated that pyrolysis reduces the potential release of pollutants from sewage sludge in landfill, making it a promising method of treating sewage sludge before landfilling.     

Electrostatic Precipitator Performance from the Point of View of Gas Treatment Time

This paper describes a risk assessment methodology for preliminary assessment of municipal sludge incineration. The methodology is a valuable tool in that it can be used for determining the hazard indices of chemical contaminants that might be present in sewage sludge used in incineration. The paper examines source characteristics (i.e., facility design), atmospheric dispersion of emission, and resulting human exposure and risk from sludge incinerators. Seven of the ten organics were screened for furtherinvestigation. An example of the calculations are presented for cadmium.     

城市污水污泥处置方式的温室气体排放比较分析

针对我国现在主流的城市污水污泥处置方法:填埋,焚烧,堆肥。用IPCC中推荐的方法和缺省值,对处置过程中产生的温室气体的直接排放、间接排放和替代排放做了计算和分析。填埋过程计算排放的温室气体有CH4,焚烧过程计算排放的有温室气体CO2和N2O,堆肥过程计算的排放的有温室气体CO2和N2O,最终比较的结果都折算成CO2的排放。结果表明,污泥填埋、焚烧、堆肥所产生的CO2的净排放量分别为695.847 kg CO2/t、443.643 kg CO2/t、511.817 kgCO2/t。由于考虑了堆肥以后的有机肥利用,从减排以及污泥资源化的角度分析,得出堆肥是相对好的污泥处置方式。     

Utilization of urban sewage sludge: Chinese perspectives

Purpose

Urbanization and industrialization in China has resulted in a dramatic increase in the volume of wastewater and sewage sludge produced from wastewater treatment plants. Problems associated with sewage sludge have attracted increasing attention from the public and urban planners. How to manage sludge in an economically and environmentally acceptable manner is one of the critical issues that modern societies are facing.

Methods

Sludge treatment systems consist of thickening, dewatering, and several different alternative main treatments (anaerobic digestion, aerobic digestion, drying, composting, and incineration). Agricultural application, landfill, and incineration are the principal disposal methods for sewage sludge in China. However, sewage sludge disposal in the future should focus on resource recovery, reducing environmental impacts and saving economic costs.

Results

The reuse of biosolids in all scenarios can be environmentally beneficial and cost-effective. Anaerobic digestion followed by land application is the preferable options due to low economic and energy costs and material reuse.

Conclusion

It is necessary to formulate a standard suitable for the utilization of sewage sludge in China.     

Incineration of paper sludge in a prototype vortexing fluidized bed combustor

All experiments were carried out in a prototype vortexing fluidized bed combustor (VFBC). The dimension of the combustion chamber is 0.7 x 1.4 x 2 m, and the freeboard section is 1 m i.d. and 4 m in height. Paper sludge was used as the feeding material. Two types of coal particles were employed as the supplementary fuel. In order to understand the characteristics of the VFBC system for paper sludge incineration, the effect of various operating parameters, such as the primary airflow, excess air ratio, and secondary airflow rates, on temperature distribution, ash elutriation, combustion efficiency, and pollutant emissions were investigated.     

市政污泥与生活垃圾混烧技术验证

对市政污泥与生活垃圾混烧进行了验证研究。结果表明,与生活垃圾单独焚烧相比,污泥与生活垃圾混烧后烟气中NOx、CO和HCl的浓度没有出现明显变化,而SO2浓度出现了下降（从82～93mg／m3下降至41～70mg／m3）;Hg、Pb、Sn、Cr和Zn的浓度均表现为不同程度的上升,但仍然符合GB[g485;二恶英从0．0087μgTEQ／m3降至O．0047μgTEQ／m3。掺烧半干污泥比例为10％、12％和15％时,吨物质的发电量分别为311．8kWh／t、306．7kWh／t和296．1kwh／t。混烧污泥在一定程度上降低了系统的发电量,因此建议混烧污泥的比例不应大于15％。测算的污泥混烧成本约209元／t（80％含水率）。     

Incineration of Paper Sludge in a Prototype Vortexing Fluidized Bed Combustor

ABSTRACT

All experiments were carried out in a prototype vortexing fluidized bed combustor (VFBC). The dimension of the combustion chamber is 0.7 x 1.4 x 2 m, and the freeboard section is 1 m i.d. and 4 m in height. Paper sludge was used as the feeding material. Two types of coal particles were employed as the supplementary fuel. In order to understand the characteristics of the VFBC system for paper sludge incineration, the effect of various operating parameters, such as the primary airflow, excess air ratio, and secondary airflow rates, on temperature distribution, ash elutriation, combustion efficiency, and pollutant emissions were investigated.