煅烧—碱溶法制粉煤灰类沸石吸附剂及其在处理含铅废水中的应用

粉煤灰吸附性能研究是当前环境科学领域中的一个研究热点，但原状粉煤灰的吸附效果不理想，本文报道的用煅烧-碱溶法制得类沸石吸附剂的比表面积为112.6m^2/g，孔隙率为83.1%，分别是改性前的40.22和1.67倍。用31.13和31.42倍，处理效果优于市售一级活性炭，并用0.1mol/L的HCl溶液和饱和NaCl溶液再生此吸附剂，解吸率达到了98%以上，此再生的类沸石吸附剂处理含铅废水的去除率也达到了83%以上。     

改性粉煤灰吸附稀土废水中的氨氮

用硫酸和氢氧化钠对粉煤灰进行酸改性和碱改性处理,研究改性前后粉煤灰对稀土废水中氨氮的吸附效果变化及最佳吸附条件,并从吸附等温线入手探讨吸附机理。结果显示,经碱改性后粉煤灰对氨氮的吸附性能有明显改善,当最佳吸附条件确定为投加量2 g,吸附时间2 h,初始pH 7～8时,碱改性粉煤灰对氨氮的吸附过程符合Freundlich等温方程式和Langmuir等温方程式。碱改性粉煤灰对氨氮的吸附属于良性吸附,且为吸热过程,室温下理论饱和吸附量为1.9066mg/g。     

改性粉煤灰及其处理废水的机理

应用正交设计的基本理论,研究了PDMDAAC(聚二甲基二烯丙基氯化铵)改性粉煤灰的最佳条件,并将改性粉煤灰用于模拟印染废水的处理,探索了改性粉煤灰处理废水的机理。结果表明,在原PDMDAAC的pH下．控制PDMDAAC的浓度为40g／L,恒温30℃．反应1h为最佳改性工艺,改性粉煤灰处理废水的机理以吸附电中和为主。     

HDTMA改性粉煤灰吸附酸性嫩黄染料废水

使用HDTMA（十六烷基三甲基溴化铵）对粉煤灰(FA)进行改性,并使用改性后粉煤灰（MFA）吸附处理酸性嫩黄染料废水。研究发现,由于改性剂HDTMA被涂敷在粉煤灰表面,使粉煤灰表面电性改变,大大增强了对酸性嫩黄的处理效果,酸性嫩黄去除率可由13.2％提高到95％以上。实验结果还表明,当染料浓度为50 mg/L时,100 mL染料中MFA的最佳投加量为700 mg;pH值对吸附效果没有显著影响;低温有利于吸附。HDTMA改性粉煤灰对酸性嫩黄染料的吸附规律可用Langmuir吸附等温式描述。     

网络版论文摘要

<正>改性粉煤灰烧结陶粒吸附SO2的研究李英赞1宋元平2(1.吉林市环境保护监测站,吉林吉林132001;2.上海交通大学机械与动力工程学院,上海200240)采用热电厂粉煤灰为主要原料制备改性粉煤灰,以改性粉煤灰、膨润土、石灰石、水泥质量比为20∶2∶2∶1的比例     

新物化法深度处理焦化废水

采用絮凝/吸附新物化法工艺对焦化废水进行深度处理.选用了新型复合高效絮凝剂(PFASSB),结合粉煤灰作为吸附剂,考察了絮凝剂用量、pH对絮凝效果的影响以及粉煤灰用量、pH、吸附时间、生石灰用量对吸附效果的影响.结果表明:(1)PFASSB最佳用量为10 mg/L,絮凝效果优于其他常用絮凝剂,适合处理焦化废水,处理前可以不用调节pH;(2)粉煤灰廉价易得、最佳用量为150 g/L,吸附饱和后的粉煤灰的处置可以考虑资源化再利用;(3)新物化法深度处理后的出水COD、NH3-N分别为70.21、19.37 mg/L,分别达到了<污水综合排放标准>(GB 8978-1996)的一级标准和二级标准.     

粉煤灰及沸石对污泥回流液中磷的吸附研究

以粉煤灰和沸石作为吸附材料,研究了两者在静态吸附、动态吸附及流化吸附3种运行状态下,对模拟污泥回流液中磷的吸附情况.试验结果表明,粉煤灰及沸石在3种吸附状态下,达到吸附平衡时TP去除率大小为静态吸附>流化吸附>动态吸附.静态吸附效果最好,但达到吸附平衡所需时间最长,相对效率较低;动态吸附吸附平衡时间短,但TP去除率较低.通过对比粉煤灰及沸石在3种不同吸附状态下的吸附特点及效果,得出宜采用中等粒级的沸石颗粒流化吸附处理污泥回流液.     

粉煤灰的改性及其在垃圾渗滤液深度处理中的应用研究

实验采用物理方法和化学方法对粉煤灰进行改性,并用改性粉煤灰深度处理垃圾渗滤液。通过扫描电镜和X-射线衍射对改性前后粉煤灰的表面结构和主要晶相组成进行分析,同时考察其在垃圾渗滤液深度处理中的吸附效果。结果表明,改性后粉煤灰的比表面积和孔隙度增大,吸附能力增强。通过比较,吸附能力最强的改性粉煤灰是将引发剂A与粉煤灰以质量比为1∶9的比例混合,在800℃下恒温焙烧2 h所制得的改性粉煤灰,该改性粉煤灰对垃圾渗滤液中COD和色度的去除率可达到67.3%和87.3%,相对于改性前去除率提高了96.0%和57.8%。     

粉煤灰协同微波-Fenton氧化法处理活性艳蓝KN-R染料废水

以粉煤灰联合微波-Fenton氧化工艺处理活性艳蓝KN-R生产废水,考察了粉煤灰投加量及吸附时间对处理效果的影响,并通过正交实验对微波-Fenton工艺参数进行了优化。实验结果表明,粉煤灰絮凝吸附与微波-Fenton氧化具有协同效应;在粉煤灰投加量为40 g/L,搅拌吸附时间为20 min,滤液pH值为4,Fe2＋和H2O2投加量分别为3.6 mmol/L和0.15 mol/L,微波功率为200 W,辐射反应时间为4 min的优化条件下,染料废水的处理效果最好,COD和色度的去除率分别达到90.90%和99.98%。     

煅烧-碱溶法制粉煤灰类沸石吸附剂及其在处理含铅废水中的应用

粉煤灰吸附性能研究是当前环境科学领域中的一个研究热点 ,但原状粉煤灰的吸附效果不理想。本文报道的用煅烧 -碱溶法制得类沸石吸附剂的比表面积为 112 .6m2 / g、孔隙率为 83 .1% ,分别是改性前的 40 .2 2和 1.67倍。用此类沸石吸附剂来处理浓度为 2 0 0mg/L的模拟含铅废水 ,去除率为 84.87% ,吸附容量为 3 3 .94mg/ g ,分别是改性前的3 1.13和 3 1.42倍 ,处理效果优于市售一级活性炭。并用 0 .1mol/L的HCl溶液和饱和NaCl溶液再生此吸附剂 ,解吸率达到了 98%以上 ,此再生的类沸石吸附剂处理含铅废水的去除率也达到了 83 %以上     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

PCDD/F formation from oxy-PAH precursors in waste incinerator flyash

The yield of PCDD/F in relation to the presence of oxygenated PAH in model waste incinerator flyash has been investigated in a fixed bed laboratory scale reactor. Experiments were undertaken by thermal treatment of the model flyash at 250 and 350 °C under a simulated flue gas stream for 2 h. After reaction, the PCDD/F content of the reacted flyash and the PCDD/F released into the exhaust gas, and subsequently trapped by XAD-II resin in a down-stream condensation system were analyzed. The PAHs investigated were, dibenzofuran and benzo[b]naphtho[2,3-d]furan and were spiked onto the model flyash as reactant precursors for PCDD/F formation. The results showed significant formation of furans from both of the PAH investigated, however except from some highly chlorinated dioxin congeners, the formation of dioxins was not so common. Benzonaphthofuran was significantly more reactive than dibenzofuran in PCDD/F formation, in spite of the fact that dibenzofuran is structurally more similar to that of PCDD/F. Thus, there was no clear attribution between the chemical structure of PAH used and the formation of PCDD/F. There were considerable differences between the yields of PCDD/F congeners in the gaseous species and those in the reacted flyash under the same operational conditions. The concentration of PCDD/Fs was reduced at the higher reaction temperature of 350 °C; however, the higher temperature resulted in the majority of the PCDD/F formed on the flyash being released into the gas phase.     

Desorption of PCDD/PCDF from municipal solid waste incinerator flyash under post-combustion plant conditions

The influence of temperature on the levels of PCDD and PCDF remaining in, and desorbed from, a municipal solid waste incinerator flyash was investigated by heating the ash to between 200 and 400 degrees C under a simulated flue gas for four days reaction time. Considerable desorption of PCDD/PCDF from the flyash was seen at 275 degrees C and above. Maximum desorption occurred at 350 degrees C, with the equivalent of nearly eight times the total PCDD/PCDF concentration of the original flyash being lost to the vapour phase per unit mass of initial flyash. The I-TEQ value of the desorbed PCDD/PCDF was considerable, being over fourteen times that of the original flyash at 325 degrees C. The results indicate that formation of PCDD/PCDF on flyash deposits in the post-combustion plant of incinerators can result in the release of significant amounts of PCDD/PCDF to the flue gas stream.     

Destruction of dioxins and furans adsorbed on flyash in a rotary kiln furnace

The paper deals with the use of a rotary kiln furnace for thermal destruction of dioxin combined with a baghouse filter for the recycling of entrained flyash and an activated carbon filter for adsorbtion of dioxin traces transported by gas phase.Measurements performed at a pilot plant with a throughput of 200 kg flyash/hr revealed 99.5 % destruction of dioxins and furans. Furthermore, the destruction of all organics, 95 % desorbtion of mercury and quantitative elimination of peripheral (located at the surface) Chromium (CrVI) were achieved.An activated carbon filter placed in the fluegas stream of an municipal waste incinerator was started up to investigate the influence of interfering constituants like SO₂, HCl etc. on the filter performance. Loading data, removal efficiency and make up performance were collected.     

粉煤灰黑液胶凝材料的研究

研究了改性黑液作粉煤灰的激发剂,并与石灰、磷石膏一起制成一种新型的胶凝材料,讨论了粉煤灰、石灰、磷石膏及黑液的用量对胶凝材料性能的影响,并通过正交试验与模糊数学分析求出了最佳工艺参数。试验结果表明,该种新材料的抗压强度能达≥20MPa,耐水性良好,且工艺简单、成本低。     

Isomeric analysis of PCDD/PCDF in waste incinerator fly ash by GC-MS/MS

The development of an analytical method for the analysis of PCDD/PCDF in flyash using a bench analytical system comprising of a gas chromatograph fitted with an ion trap detector operated in the tandem MS mode is described. The optimum settings for the most important MS/MS parameters are given, including those for the less reported mono- to tri-chlorinated dioxin and furan congener groups. Flyash samples from three waste incineration plants representing a decommissioned 1970s plant design, an upgraded and still operating plant originally designed in the 1970s, and a modern 1990s design operating plant have been analysed for PCDD/PCDF. The flyash samples were analysed for PCDD/PCDF using the methods developed and the total PCDD/PCDF, I-TEQ values and isomeric profiles are reported. The flyash from the older decommissioned incinerator had very significantly higher concentrations of PCDD/PCDF compared to the modern incinerator flyash.     

Influence of temperature on PCDD/PCDF desorption from waste incineration flyash under nitrogen

A municipal solid waste incinerator flyash was heated to between 200 and 400 degrees C under nitrogen in a bench-scale, static bed reactor for 4 days soak time. The influence of temperature on the levels of PCDD and PCDF remaining in and desorbed from the ash were investigated using GC-MS/MS. PCDD and especially PCDF formation was seen on the flyash between 225 and 300 degrees C. Large increases in the I-TEQ of the treated ash relative to the increase in its overall PCDD/PCDF content indicated that the formation of 2378-substituted congeners was favoured over that of other substitution patterns. In the absence of a source of gaseous oxygen, formation was mainly attributed to de novo reactions involving solid phase oxygen. Dechlorination of the PCDD/PCDF in flyash became increasingly important above 275 degrees C. Maximum desorption was seen at 325 degrees C, with the equivalent of 35 wt% of the PCDD/F in the original flyash being recovered from the exhaust traps at this temperature. The desorbed species were mainly M(1)CDD/CDDF-T(3)CDD/CDDF resulting from dechlorination of higher chlorinated PCDD/PCDF, with consequently low I-TEQ values.     

烟气脱硫石灰石活性测试装置设计研究

石灰石的活性对烟气脱硫工艺具有重要意义.设计了一套石灰石活性测试装置,该装置可模拟实际脱硫塔的反应过程,测试结果能够准确反映石灰石的活性.     

Flue Gas Desulfurization: The State of the Art

ABSTRACT

Coal-fired electricity-generating plants may use SO₂ scrubbers to meet the requirements of Phase II of the Acid Rain SO₂ Reduction Program. Additionally, the use of scrubbers can result in reduction of Hg and other emissions from combustion sources. It is timely, therefore, to examine the current status of SO₂ scrubbing technologies. This paper presents a comprehensive review of the state of the art in flue gas desulfurization (FGD) technologies for coal-fired boilers.

Data on worldwide FGD applications reveal that wet FGD technologies, and specifically wet limestone FGD, have been predominantly selected over other FGD technologies. However, lime spray drying (LSD) is being used at the majority of the plants employing dry FGD technologies. Additional review of the U.S. FGD technology applications that began operation in 1991 through 1995 reveals that FGD processes of choice recently in the United States have been wet limestone FGD, magnesium-enhanced lime (MEL), and LSD. Further, of the wet limestone processes, limestone forced oxidation (LSFO) has been used most often in recent applications.

The SO₂ removal performance of scrubbers has been reviewed. Data reflect that most wet limestone and LSD installations appear to be capable of ~90% SO₂ removal. Advanced, state-of-the-art wet scrubbers can provide SO₂ removal in excess of 95%.

Costs associated with state-of-the-art applications of LSFO, MEL, and LSD technologies have been analyzed with appropriate cost models. Analyses indicate that the capital cost of an LSD system is lower than those of same capacity LSFO and MEL systems, reflective of the relatively less complex hardware used in LSD. Analyses also reflect that, based on total annualized cost and SO₂ removal requirements: (1) plants up to ~250 MW_e in size and firing low- to medium-sulfur coals (i.e., coals with a sulfur content of 2% or lower) may use LSD; and (2) plants larger than 250 MW_e and firing medium- to high-sulfur coals (i.e., coals with a sulfur content of 2% or higher) may use either LSFO or MEL.     

湿法脱硫石灰石浆液密度的敏感性分析

石灰石浆液的性能是影响湿法烟气脱硫效率的主要因素,而石灰石浆液的密度又是影响其性能的主要参数。现场制浆过程中,运行参数的变动会使得浆液密度值发生变化,从而影响浆液性能。因此,通过调整制浆系统运行参数,寻找石灰石浆液密度敏感因素,对优化浆液性能具有重要意义。以某600 MW火力发电厂湿式脱硫制浆系统作为研究对象,通过现场...