水力空化-O3氧化联合超声吸附处理煤气化废水

采用水力空化-O₃氧化与超声吸附法联合处理煤气化废水。吸附剂以钙基膨润土为原料,经十六烷基三甲基溴化铵改性制得。通过单因素实验分别探讨了水力空化-O₃氧化与超声吸附的适宜处理条件,并在该条件下对废水进行联合处理。实验结果表明：在O₃通量194.4 mg/L、空化时间60 min、入口压力0.4 MPa、废水pH 10.00的优化条件下,水力空化-O₃氧化对COD和苯酚的去除率分别达67.3%和57.5%;在此基础上进一步采用超声吸附法处理废水,在吸附剂投加量0.06 g/mL、超声时间60 min、废水pH 4.00、吸附温度25 ℃的优化条件下,处理后出水中COD和苯酚质量浓度分别降至317.1 mg/L和117.9 mg/L;COD和苯酚的总去除率分别达97.9%和96.6%。     

选择性吸附-高效生物降解法处理含硝基苯与苯酚混合废水

结合NDA-150型树脂（简称树脂）选择性吸附和生物降解的优点,对含硝基苯和苯酚的模拟混合废水（简称混合废水）进行处理。通过树脂的选择性吸附,使混合废水中的硝基苯和苯酚分离,随后用高效菌对树脂所吸附的硝基苯进行生物降解,同时实现树脂的再生。实验结果表明：通过调节混合废水的pH,树脂可有效地将混合废水中的硝基苯和苯酚进行选择性吸附分离;树脂对硝基苯的吸附是可逆的;树脂的再生程度受微生物对可利用硝基苯质量浓度的下限（1．2mg／L）限制;吸附-生物再生循环实验结果表明,该树脂可有效抵抗微生物的生物降解与破坏。     

Tailoring mesoporosity of poly(furfuryl alcohol)-based activated carbons and their ability to adsorb organic compounds from water

In this work it was shown that polymers can be recycled into a promising adsorbent for organic dyes and phenols waste removal. For this, a series of activated carbons (ACs) were produced from mixture of ferrocene or titanium acetylacetonate with poly(furfuryl alcohol) (PFA) by steam activation. The introduction of ferrocene as Fe precursor was found to be an efficient catalyst in mesoporosity development during carbonization and subsequent steam activation at 850 °C, whereas the polymer based only and titanium-doped ACs are typically microporous. The porous structure parameters were determined from nitrogen adsorption isotherms measured at 77 K. Scanning electron microscopy was applied to monitor the metal distribution of metal-loaded char and the surface morphology of activated carbons. The adsorption capacity was found to be dependent mainly on pore size distribution. In the case of phenol adsorption, the adsorption was defined by volume of pore with size 0.8–1.4 nm; whereas, for Congo red best fit was observed for volume of pore with size 2–5 nm.

     

Treatment of olive mill waste water with activated carbons from agricultural by-products

A series of activated carbons prepared by a two-step steam activation of olive stone and solvent extracted olive pulp (SEOP) have been used in an attempt to investigate the total phenol removal and chemical oxygen demand (COD) decrease in olive mill waste water (OMWW). The temperature of carbonization and activation were kept constant at 850 and 800 degrees C, respectively. One of the carbons was prepared by a single-step process at 800 degrees C. Activated carbons have been characterized by adsorption of N2 at 77 K and mercury porosimetry. Their iodine values were also determined. Surface oxides of activated carbons were determined using the Boehm's method. The porosity development and the surface chemistry of carbons were correlated to increasing removal ability of organic molecules. Kinetics of adsorption was evaluated by applying the Lagegren model while adsorption isotherm data were fitted to Langmuir model. Mesoporosity seems to be the key factor for total phenol removal while micoporosity controls the adsorption of total organics as expressed by the COD decrease in OMWW. For carbons with similar structure, the adsorption of phenols or total organics might be affected by the presence of carbonyls.     

阳离子嫩黄染料与苯酚在活性炭上竞争吸附的研究

用阳离子嫩黄染料和苯酚作为分子量差异悬殊的两种机吸附质，研究它们在两种国产活性炭上的吸附性能。在双组分竞争吸附中，阳离子嫩黄染吸附占明显优势，而 酚的吸附量则比在单组分系统时要小。本文还用理想吸附溶液（ＩＡＳ）模型对双组分竞争吸附作了预测。     

NaOH改性活性炭的表面特征及吸附甲醛的性能

研究了NaOH改性活性炭(AC)的表面官能团变化特征及其吸附甲醛的性能.实验结果表明:改性AC表面的羧基、酚羟基、内酯基等官能团均与NaOH发生化学反应;质量分数为30%的NaOH溶液对AC表面的清洗作用最大,能将AC表面的杂质基本清除,此时AC表面羧基、酚羟基、内酯基和羰基浓度均达到最大;NaOH溶液质量分数为30%时,改性AC吸附甲醛的效果最好;改性AC表面酚羟基浓度的大小与改性AC吸附甲醛气体穿透时间的长短呈正比.     

Agricultural solid waste for the removal of organics: adsorption of phenol from water and wastewater by palm seed coat activated carbon

Adsorption studies for phenol removal from aqueous solution on activated palm seed coat carbon (PSCC) were carried out under varying experimental conditions of contact time, phenol concentration, adsorbent dose and pH. Adsorption equilibrium was reached within 3 h for phenolic concentrations 10-60 mg l(-1). Kinetics of adsorption obeyed a first order rate equation. The percent removal remained constant over the pH range 4-9 for a phenolic concentration of 25 mg (l-1). The equilibrium data could be described well by the Freundlich isotherm equation. The adsorption of phenol on PSCC follows the film diffusion process. A comparative study with a commercial activated carbon showed that PSCC is two times more effective than commercial activated carbon. The studies showed that the palm seed coat carbon can be used as an efficient adsorbent material for the removal of phenolics from water and wastewater.     

Physical and chemical properties study of the activated carbon made from sewage sludge

Preparation of activated carbon from sewage sludge is a promising way to produce a useful adsorbent for pollutants removal as well as to dispose of sewage sludge. The objective of this study was to investigate the physical and chemical properties of the activated carbon made from sewage sludge so as to give a basic understanding of its structure. The activated carbon was prepared by activating anaerobically digested sewage sludge with 5 M ZnCl2 and thereafter pyrolyzing it at 500 degrees C for 2 h under nitrogen atmosphere. The properties investigated in the present study included its surface area and pore size distribution, its elemental composition and ash content, its surface chemistry structure and its surface physical morphology. Furthermore, its adsorption capacities for aqueous phenol and carbontetrachloride were examined. The results indicated that the activated carbon made from sewage sludge had remarkable micropore and mesopore surface areas and notable adsorption capacities for phenol and carbon-tetrachloride. In comparison with commercial activated carbons, it displayed distinctive physical and chemical properties.     

水力空化-Fenton氧化联合超声吸附处理煤气化废水

采用水力空化-Fenton氧化联合超声吸附处理煤气化废水,考察了单独Fenton氧化及单独水力空化工艺条件,并对Fenton氧化、水力空化和水力空化-Fenton氧化工艺处理过程进行了动力学初探。实验结果表明:在反应时间60 min、废水pH 3.0、Fe~(2+)加入量900 mg/L、H_2O_2加入量3 600 mg/L、空化压力0.4 MPa的条件下,水力空化-Fenton处理煤气化含酚废水的COD和苯酚去除率分别为93.05%和90.29%;进一步采用超声吸附处理后,出水COD和苯酚质量浓度分别为92.9 mg/L和4.5 mg/L,达到GB 8978—1996《污水综合排放标准》三级指标。     

改性膨润土对水中蒽的吸附和解吸

分别用长碳链季铵盐阳离子型表面活性剂溴化十六烷基三甲铵（HDTMAB）、短碳链季铵盐阳离子型表面活性剂四甲铵化溴（TMAB）及非离子型表面活性剂聚乙二醇（PEG）对天然膨润土进行改性。比较了不同类型改性膨润土对水中蒽的吸附性能,探讨了吸附机理。实验结果表明,天然膨润土及改性膨润土对水中蒽的吸附能力依次为HDTMAB改性膨润土〉PEG改性膨润土〉TMAB改性膨润土〉天然膨润土;吸附等温线均是直线,说明该吸附行为是分配作用的结果。不同蒽初始质量浓度下,各种改性膨润土对蒽的吸附量由大至小的顺序为HDTMAB改性膨润土〉PEG改性膨润土〉TMAB改性膨润土,而天然膨润土对蒽的吸附量随蒽初始质量浓度的变化很小。改性膨润土加入量为30～80g/L时,各种改性膨润土对水中蒽的去除率均可达到90％以上,且解吸率均在5％以下。     

有机硅改性泥炭的吸附性能研究

采用三甲基氯硅烷处理泥炭(泥炭硅烷化),使其吸附性能得以改善。采用硅烷化泥炭自水溶液中吸附苯甲酸、苯甲醛和苯酚的等温线进行测定,对吸附过程的△G、△H和△s进行计算。试验结果表明：熵变是这类体系吸附过程的重要驱动力;硅烷化后的泥炭表面的疏水性明显增强,对水溶液中芳香族化合物的吸附量增大。     

Dual Function of Cellulose Triacetate–Graft–Polymethacrylic Acid Films for Dyes Removal and for High-Dose Radiation Dosimetry

Graft copolymerization of methacrylic acid (MAc) onto cellulose triacetate (CTA) films was conducted by gamma rays. The grafting conditions were optimized. The structure of grafted CTA films was characterized by Fourier transform infra red–attenuated total reflection, scanning electron microscopy, thermal gravimetric analysis, CHNS/O microanalyzer and, surface area and porosity analyzer. The grafted CTA films were exploited in adsorption of ethyl violet (EV) and phenol red (PR) dyes. The adsorption capacity of the grafted CTA films was investigated at various variables. The adsorption isotherms and kinetic study were examined. Further, the dyed grafted CTA films were used in measurements of high dose radiation. The results indicate that the useful dose range extents up to 440 and 300 kGy for EV and PR, respectively. The effects of relative humidity during irradiation, shelf-life, pre- and post-irradiation storage in dark and indirect daylight conditions on dosimeters performance were investigated.     

HZ-16型大孔树脂吸附处理含RDT-8废水

采用HZ-16型大孔树脂对含三（三溴苯氧基）三嗪（RDT-8）废水进行吸附及脱附处理。实验结果表明：在废水流量为4.0 BV/h的条件下,树脂最佳吸附工艺条件为出水体积88.0 BV,此条件下出水COD小于291 mg/L,挥发酚质量浓度小于0.08 mg/L;在脱附液流量为0.5 BV/h的条件下,树脂最佳脱附工艺条件为脱附液体积3.0 BV,此条件下脱附液中挥发酚质量浓度为30.6 mg/L,挥发酚脱附率高达76.4%。在最佳吸附-脱附工艺条件下,连续进行10次动态吸附-脱附实验,吸附出水中COD为137~294 mg/L,COD去除率为72.5%~89.1%,挥发酚质量浓度稳定在0.05 mg/L以下,挥发酚去除率为99.8%~100%,说明HZ-16型大孔树脂的吸附-脱附性能稳定。     

功能季铵盐改性蒙脱土吸附刚果红染料

以1,3-双[二(2-羟乙基)十二烷基溴化铵]丙烷(12-3-12(OH))对钠基蒙脱土(Na-Mt)进行插层改性,制备了有机蒙脱土(OMt)。采用FTIR、XRD和SEM等方法对用不同改性剂用量改性的OMt进行了表征,考察了吸附剂用量和体系pH对OMt吸附刚果红(CR)性能的影响,并探究了其吸附规律。表征结果显示:OMt表面有明显的褶皱,层间空隙随着改性剂用量的增加而增大。OMt作为吸附剂去除水中CR的最佳条件为:吸附剂用量0.4 g/L,自然pH (pH=7.12)。准二级动力学模型可以较好地描述1.0 OMt(12-3-12(OH)与Na-Mt可交换阳离子的摩尔比为1∶1)对CR的吸附过程,1.0 OMt吸附CR的过程更符合Langmuir模型,最大吸附量为248.14 mg/g,且为自发的吸热过程。重复使用3次,CR去除率保持在90%左右。     

A comparative adsorption/biosorption study of mono-chlorinated phenols onto various sorbents

The potential use of dried activated sludge and fly ash as a substitute for granular activated carbon for removing mono-chlorinated phenols (o-chlorophenol and p-chlorophenol) was examined. The pollutant binding capacity of the adsorbent/biosorbent was shown to be a function of substituted group, initial pH and initial mono-chlorinated phenol concentration. The working sorption pH value was determined as 1.0 and the equilibrium uptake increased with increasing initial mono-chlorinated phenol concentration up to 500 mg dm(-3) for all the mono-chlorinated phenol-sorbent systems. The suitability of the Freundlich, Langmuir and Redlich-Peterson adsorption models to the equilibrium data were investigated for each mono-chlorinated phenol-sorbent system. The results showed that the equilibrium data for all the mono-chlorinated phenol-sorbent systems fitted the Redlich-Peterson model best within the concentration range studied.     

Textural and surface chemical characteristics of activated carbons prepared from cattle manure compost

Two activated carbons (ACs) prepared from cattle manure compost (CMC) by ZnCl(2) activation were selected and out-gassed in a helium flow at various temperatures for 2h. The pore structure and surface chemical properties of the two selected ACs and their out-gassing treated ACs were characterized using N(2) adsorption-desorption, elements analysis, SEM and Boehm titration. A basic dye, methylene blue (MB), was chosen as an adsorbate to investigate the adsorption capacity for organic contaminant onto the activated carbons. It was found that the out-gassing treatment at 400 degrees C had little effect on the textural characteristics of the carbons but significantly changed the surface chemical properties such as surface functional groups concentration, pH and pH(PZC). The CMC-based activated carbons exhibited excellent performance for MB adsorption due to their high surface area, large mesopore volume and high nitrogen content. The kinetics of MB adsorption onto the activated carbons followed a pseudo-second-order equation, and the equilibrium data agreed well with the Langmuir model under the experimental conditions. The highest adsorption rate constant of k(ad) and the largest adsorption capacity of q(m) were found be 1.44x10(-4)g/mgmin and 519mg/g, respectively. The results suggested that the CMC-based activated carbons were effective adsorbents for the removal of methylene blue from aqueous solution.     

Adsorption characteristics of Cu2+ and Zn2+ from aqueous solution using carbonized food waste

The aim of the present study was to analytically provide adsorption characteristics of Cu²⁺ and Zn²⁺ using carbonized food waste (CFW); more specifically, batch tests were conducted using various concentrations of metal ions, contact times, and initial pH levels in an attempt to understand the adsorption removal of heavy metal ions in aqueous solution at concentrations ranging between 50 and 800 mg/l. The results confirmed that the adsorption equilibrium was established within a maximum of 80 min, and the maximum concentrations for adsorption of Cu²⁺ and Zn²⁺ were 28.3 and 23.5 mg/g, respectively. These adsorption levels indicate that CFW has better performance than many other adsorbents. In experiments using different pH conditions, the applicability to acid wastewater was found to be high, and an excellent adsorption removal ratio of 75%–90% was observed under acid conditions at pH 2–4. Furthermore, as the adsorption time increased, the calcium component in the CFW began to leach into the aqueous solution and raise the pH, accordingly causing the removal of heavy metal ions partially as a result of precipitation. When our results were analyzed using the Langmuir model and the Freundlich model for isothermal adsorptivity, the activity of CFW in this study was shown to be more consistent with the former; the adsorption speed of Cu²⁺ and Zn²⁺ according to a pseudosecond-order reaction model was found to be very fast for an initial concentration of not more than 100 mg/l. In a test in which an attempt was made to compare adsorption capacity values obtained from the experiments in this study with the aforementioned three models, the pseudosecond-order reaction model was found to provide results closest to the actual values.     

Decomposition of hazardous organic materials in the solidification/stabilization process using catalytic-activated carbon

The application of a catalytic-activated carbon to the solidification/stabilization (S/S) process for immobilization of phenol and 2-chlorophenol and catalytic decomposition was investigated. The effect of the catalytic-activated carbon, in amounts of 0.25-1% (by dry sand wt.), on the leaching of phenol and 2-chlorophenol was studied. H2O2 was added as a source of oxygen in the amounts of 1 or 5%, with respect to liquid solution weight. Toxicity characteristic leaching procedure (TCLP) leaching tests showed that adding the catalytic-activated carbon to the S/S matrix significantly reduced the leachability of both phenol and 2-chlorophenol. Only trace amounts of phenol were found in the leaching solution, while the concentration of 2-chlorophenol was below the detection limit of the gas chromatography (GC). Without addition of the catalytic-activated carbon, 87% of the phenol and 92% of the 2-chlorophenol leached. Additional tests on TCLP leachate solutions using GC-mass spectrometry indicated the existence of simple, less hazardous, hydrocarbons, including alcohol. Catalytic-activated carbons treated with phenol in the presence of H2O2 were also analyzed using time of flight-secondary ion mass spectroscopy (TOF-SIMS). Results indicate that the phenol aromatic ring was broken by the catalytic reaction.     

Pore structure and adsorption properties of activated carbon prepared from granular molded waste paper

We have previously manufactured activated carbon using waste paper board, which was prepared by adding 8% phenol resin adhesive to torn waste newspaper and hot-pressing. In this study, the pretreatment process of the raw material was simplified; the waste paper was extruded to form granules. The activated carbon was manufactured by the carbon dioxide activation method using the granules as the raw material. The properties of the activated carbon were evaluated based on the pore structure, the iodine adsorption number, and the adsorption of toluene vapor in a sealed chamber. The activated carbon, which was manufactured at an activation temperature of 1100°C and a treatment time of 60min, exhibited a specific surface area of 1241m²/g and an iodine adsorption number of 1120mg/g. These results were similar to those obtained for two commercially available activated carbons. The extent of toluene vapor adsorption by this activated carbon was similar to that observed for the two commercial activated carbons over a period of 130min.     

Fluoride sorption by treated fly ash: kinetic and isotherm studies

High fluoride levels in drinking water have become a critical health hazard. In the present study, the performance of magnesia-loaded fly ash adsorption in the removal of fluoride from aqueous solution was investigated in a batch study. The effect of contact time, dosage, pH, temperature and agitation speed was studied at different values. The maximum removal efficiency was 88 % at 150 min. The effective dose of adsorbent was found to be 2.5 g/l. The optimum pH was found to be at pH 4. Kinetic studies and isotherm studies were also performed to understand the ability of the adsorbents. The monolayer adsorption capacity determined from the Langmuir adsorption equation was found to be 11.61 mg/g. The kinetic measurements suggested the involvement of pseudo-second-order kinetics in adsorption and were controlled by a particle diffusion process. Overall, the results of this study suggest that magnesia-loaded fly ash is an environmentally friendly, efficient and low-cost adsorbent, useful for the removal of fluoride from aqueous solution.