Diffusion test of 20 kinds of waste molten slags and competitive materials

“Waste molten slag” is a glass-like material produced by the vitrification of solid waste or solid waste incineration residue. When using slags of this kind in a natural environment, their impact is anticipated to be at the same level as competitive or substituted materials. In this study, we made comparative evaluations between waste molten slags and competitive materials, using 20 samples in total. It was proved that release fluxes of metals from molten slags of municipal solid waste were almost at the same level as competitive or substituted materials. However, a larger impact will be caused from some types of slag that contain harmful metals in high concentrations, such as the slag from shredded automobile residues. The results of release flux showed that nearly 80% of the slope of the flux did not fit with the diffusion range. However, the linearity of every flux was extremely high, regardless of the slope.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Methods for household waste composition studies

The question is how to conduct household waste composition studies. The review is divided into three parts: overview of known methods, sampling theory, and the waste components. Twenty methods are listed and commented on. There is no adopted, working international standard. In accordance with Pierre Gy's Theory of Sampling, the seven types of sampling errors, when collecting and splitting solid samples, are described and commented on in relation to sampling of household solid waste. It is concluded that the most crucial choices in household waste composition studies are: to divide the investigation into relevant number and types of strata; to decide the required sample size and number of samples; to choose the sampling location, i.e., sampling at household level or sampling from loads of waste collection vehicles; and to choose the type and number of waste component categories to be investigated. Various classifications of household waste components used in composition studies are listed and discussed. Difficulties and weaknesses of the reviewed methods are discussed and concluded in suggested questions for further research.     

Numerical simulation of municipal solid waste combustion in a novel two-stage reciprocating incinerator

A mathematical model was presented in this paper for the combustion of municipal solid waste in a novel two-stage reciprocating grate furnace. Numerical simulations were performed to predict the temperature, the flow and the species distributions in the furnace, with practical operational conditions taken into account. The calculated results agree well with the test data, and the burning behavior of municipal solid waste in the novel two-stage reciprocating incinerator can be demonstrated well. The thickness of waste bed, the initial moisture content, the excessive air coefficient and the secondary air are the major factors that influence the combustion process. If the initial moisture content of waste is high, both the heat value of waste and the temperature inside incinerator are low, and less oxygen is necessary for combustion. The air supply rate and the primary air distribution along the grate should be adjusted according to the initial moisture content of the waste. A reasonable bed thickness and an adequate excessive air coefficient can keep a higher temperature, promote the burnout of combustibles, and consequently reduce the emission of dioxin pollutants. When the total air supply is constant, reducing primary air and introducing secondary air properly can enhance turbulence and mixing, prolong the residence time of flue gas, and promote the complete combustion of combustibles. This study provides an important reference for optimizing the design and operation of municipal solid wastes furnace.     

ANALYSIS OF RESIDENTIAL SOLID WASTE AT GENERATION SITES

An essential preliminary step in municipal solid waste (MSW) management is the accurate determination of the quantities and composition of the wastes. The purpose of this study was to test a procedure for the determination of these parameters at the source of generation (houses), rather than getting such data at transfer stations or disposal sites, as usually done in most previous studies. The average generation rate in kg per capita day⁻¹and percentages of various components of residential solid waste in Abu Dhabi City were determined by carrying out a statistically designed sampling survey. This survey covered 40 houses with different socio-economic levels and totalled 840 samples. The study showed an average generation rate of 1.76 kg per capita day⁻¹. Linear regression analysis revealed that this rate was dependent on the income level with an increase of about 35% for the high income residents over the average rate. The waste contained approximately 50% food waste. Frequency distribution analysis of waste composition data indicated that the food waste component is normally distributed, whereas the other components do not show a normal distribution pattern.     

Path analysis of factors influencing household solid waste generation: a case study of Xiamen Island,China

Comprehensive study of the factors influencing household solid waste (HSW) generation is crucial and fundamental for exploring the generation mechanism and forecasting future dynamics of HSW. A case study of Xiamen Island, China was employed to reveal the direct and indirect effects of demographic/socioeconomic factors on solid waste generation at the urban household scale. Based on a face-to-face questionnaire and two-stage survey of solid waste generation, a path analysis model was built. Results showed that the proposed path model exhibited good fit indices. Family size and dinning-at-home rate (DR), whose coefficients were ?0.40 and 0.43, respectively, were the two major factors influencing HSW directly. Moreover, family size, education level, employment rate and age structure played different degrees of indirect effects on HSW generation through respective paths, which should not be ignored. In terms of total effects, coefficients of family size, DR and employment rate were ?0.46, 0.43 and ?0.37, respectively, which were three most dominant factors influencing HSW generation. As for waste composition, organic waste was the most representative of HSW dynamics, and was the most sensitive to impact by the factors studied. Quantitative results of this study have important policy implications for sustainable municipal solid waste management.     

The use of chemical composition data in waste management planning--a case study

As the waste industry continues to move from a disposal-based system to one based on a combination of recovery options, the need for information on the composition of waste increases and this is reflected by the amount of information on the physical composition of municipal solid wastes that is now available. However, there is far less information on the chemical composition of municipal solid waste. The results from a number of chemical surveys from Europe are compared and show a reasonable degree of agreement, but several problems were identified with the data. Chemical and physical compositional data are combined in a case study example to investigate the flow of key potential pollutants in an integrated solid waste management system that uses materials recycling, composting, incineration and landfilling. This case study has shown that an integrated waste management strategy diverts lead and cadmium away from composting and recycling to incineration, which effectively isolates these elements from the environment through efficient capture of the pollutants followed by secure landfilling or recycling of the residues. However, further work is needed to determine the distribution of mercury in incineration residues and its fate when the residues are landfilled.     

Proximate composition of household waste and applicability of waste management technologies by source separation in Hanoi,Vietnam

The organic fraction of municipal solid wastes in Southeast Asia, which has a high moisture content, accounts for a large proportion of total waste. Local governments need to pay adequate attention to the composition of wastes to determine alternative waste management technologies. This study proposed the use of a triangle diagram to describe changes in proximate composition and rates of successful source separation of municipal solid waste and to identify technical challenges about alternative waste management technologies such as incineration, composting, and refuse-derived fuel production based on physical and proximate composition analysis of household waste sampled in Hanoi, Vietnam, as a case study. The analysis indicated the effectiveness of different types of source separation as well as different levels of successful achievement of source separation as an adjustment mechanism for the proximate composition of waste. Proper categorization of wastes for source separation is necessary for the appropriate use of alternative waste management technologies. The results showed that, at a source separation rate of just greater than 0.52 in a three-way separation scheme, the waste separated as combustible waste would be suitable for incineration with energy recovery. Based on well-designed schemes of source separation, alternative waste management technologies can be applied.     

Review of LCA studies of solid waste management systems – Part I: Lessons learned and perspectives

The continuously increasing solid waste generation worldwide calls for management strategies that integrate concerns for environmental sustainability. By quantifying environmental impacts of systems, life cycle assessment (LCA) is a tool, which can contribute to answer that call. But how, where and to which extent has it been applied to solid waste management systems (SWMSs) until now, and which lessons can be learnt from the findings of these LCA applications? To address these questions, we performed a critical review of 222 published LCA studies of SWMS. We first analysed the geographic distribution and found that the published studies have primarily been concentrated in Europe with little application in developing countries. In terms of technological coverage, they have largely overlooked application of LCA to waste prevention activities and to relevant waste types apart from household waste, e.g. construction and demolition waste. Waste management practitioners are thus encouraged to abridge these gaps in future applications of LCA. In addition to this contextual analysis, we also evaluated the findings of selected studies of good quality and found that there is little agreement in the conclusions among them. The strong dependence of each SWMS on local conditions, such as waste composition or energy system, prevents a meaningful generalisation of the LCA results as we find it in the waste hierarchy. We therefore recommend stakeholders in solid waste management to regard LCA as a tool, which, by its ability of capturing the local specific conditions in the modelling of environmental impacts and benefits of a SWMS, allows identifying critical problems and proposing improvement options adapted to the local specificities.     

Composition and production rate of solid waste from dental laboratories in Xanthi, Greece

The composition and production rate of solid waste produced by four dental laboratories were measured in the Prefecture of Xanthi (Greece) during 2002. The selected dental labs in Xanthi were expected to produce approximately 75% of the waste produced from of all seven dental laboratories in the Xanthi Prefecture. Sampling was performed during a 2-month period. Solid waste was categorized into three major categories: (a) infectious and potentially infectious waste, (b) non-infectious toxic waste and (c) household type solid waste. Dental laboratories solid waste (DLSW) was produced at a rate of 0.059 g/cap/day (or 22 g/cap/year) at the time of the study. Household type waste, infectious and potentially infectious waste and non-infectious toxic waste comprised approximately 74%, 26% and less than 0.5% of the total DLSW weight produced, respectively. DLSW was estimated to be approximately 0.007% of the amount of municipal solid waste produced in the Prefecture of Xanthi.     

Comparative analysis of hazardous household waste in two Mexican regions

Household hazardous waste (HHW) generation in two Mexican regions was examined, a northern region (bordering with the USA) and a central region. The aim of this work was to determine the dynamics of solid waste generation and to be able to compare the results of both regions, regarding consumption patterns and solid waste generation rates. In the northern region, household solid waste was analysed quantitatively. In order to perform this analysis, the population was categorized into three socioeconomic strata (lower, middle, upper). Waste characterization revealed the presence of products that give origin to household hazardous waste. In the northern region (Mexicali city), household hazardous waste comprised 3.7% of municipal solid waste, the largest categories in this fraction were home care products (29.2%), cleaning products (19.5%) and batteries and electronic equipment (15.7%). In the central region, HHW comprised 1.03% of municipal solid waste; the main categories in this fraction were represented by cleaning products (39%), self care products (27.3%), and insecticides (14.4%). In Mexicali, the socioeconomic study demonstrated that the production of HHW is independent of the income level. Furthermore, the composition of the solid waste stream in both regions suggested the influence of another set of variables such as local climate, migration patterns and marketing coverage. Further research is needed in order to establish the effect of low quantities of HHW upon the environment and public health.     

Composition of source-sorted municipal organic waste collected in Danish cities

Source-sorted municipal organic waste from different dwelling types in five Danish cities was sampled during one year. The samples were from permanent, full-scale systems or temporary, experimental systems for collection of source-sorted municipal organic waste. Pre-treatment of the organic waste prior to biological treatment was used in all cities to remove foreign objects and provide size reduction. All sampling was performed after pre-treatment in order to obtain more homogeneous and representative samples. The sampling included both the pre-treated waste and the reject from the pre-treatment allowing for estimation of the composition of the original waste. A total of 40 waste samples were chemically characterised with respect to 15 parameters. The waste generally consisted of around 88% VS of which an average of 80% was easily degradable. The average content of N, P and K in the dry matter of the organic waste was 2.5%, 0.4% and 0.9%, respectively. A general analysis of variance was applied to show the influence of the collection system, dwelling type and annual season on the waste composition. The content of plastic and crude fibres in the waste differed the most among the samples, probably due to use of different bag types (plastic and paper) in the different collection systems. Variations in the ash content and the calorific value might be explained by differences in the sorting instructions (whether soil and cat litter are allowed in the organic fraction). Significant seasonal variations were seen for ash, S and Cl. Dwelling type showed no statistically significant influence on any waste components. A test for uniform distribution of the p-values from the analysis of variance (Kolmogorov-Smirnov test) showed that the overall composition of the collected waste was strongly affected by the collection system (city) and season, while dwelling type had no significant influence.     

Leachate recirculation effects on waste degradation: study on columns

The purpose of this study is to determine the impact of leachate recirculation on the degradation of municipal solid wastes (bioreactor concept). The study was carried out using columns containing approximately 50 kg of waste, in order to follow waste degradation over a limited time. Three types of waste were studied: fresh waste of standard composition, fresh waste of fermentable composition and some 8-yr-old waste extracted from a site in France. Measurement of the global parameters, such as chemical oxygen demand (COD), volatile acidity, alkalinity, leachate conductivity, methane potential of the wastes and biogas production monitoring (volume of CO2 and CH4 produced), were carried out. The quantity of oxydizable matter and biogas production was increased by the leachate recirculation, and the duration of the first degradation phases was reduced in all cases. Chloride, ammonium and organic pollution accumulation was observed according to the duration of recirculation. After 400 days of degradation, waste stabilization seemed to be reached for all of the recirculated columns (COD<300 mg/L O2, and methane potential reached).     

Development of a MSW classification system for the evaluation of mechanical properties

To date, sparse information is available on the mechanical properties of municipal solid waste and the results of published work are often hard to compare due to differences in waste composition and therefore properties. To allow comparison, a unified classification system for waste is deemed crucial. Existing classification systems are presented and discussed. For a geotechnical classification, mechanical properties, size, shape and degradability potential of waste components have to be taken into account. A new and improved classification system for waste components is proposed, which complies with the requirements of a geotechnical classification system. It classifies waste components based on: (1) their material engineering properties (e.g., shear, compressive and tensile strength), (2) a size distribution of the components, (3) the component shape (reinforcing, compressible and incompressible), and (4) the degree of degradability. The proposed classification system is applied to data from the literature and methods for presenting classification information are demonstrated. Further work required to develop a full classification system for waste bodies is highlighted.     

A methodology for solid waste characterization based on diminishing marginal returns

A methodology is developed for estimating the number of waste sorts for characterizing solid wastes into categories based on diminishing minimum incremental information. Convergence in the square of the coefficient of variation with successive waste sorts is used to indicate cost-efficient termination of sampling at substantially reduced numbers of sorts in comparison with existing methodologies. These findings indicate that the numbers of waste sorts beyond that determined using the proposed methodology do not add substantial marginal gains in information and/or reduction in the confidence interval of the estimate. The methodology is demonstrated using waste composition analyses from the Greater Vancouver Regional District where 22 waste sorts are examined. The proposed methodology is simple, and the number of waste sorts can be estimated with a hand-held calculator and utilized in the field.     

Extended phase relations and load effects in MSW

The moisture retention and compression characteristics of municipal solid waste under self-weight are likened to those of an unsaturated soil. By assuming that the solid organic fraction in waste retains a relatively immobile micropore moisture and that deformation at low confining stress occurs at the expense of a relatively large macropore system, an insight into the variation of density and moisture with depth can be gained. With data on the composition of the waste, the phase composition can be extended to distinguish between solid organic and solid inorganic fractions, resulting in a four phase material model. The model is developed using detailed moisture and waste composition data from the Lyndhurst Sanitary Landfill site in Victoria, Australia. Finally, comparison of the model with large scale compression test results provides an insight into the nature of waste compression and moisture content data at low confining stress.     

Report: future industrial solid waste management in pars Special Economic Energy Zone (PSEEZ), Iran.

The Pars Special Economic Energy Zone (PSEEZ) is located in the south of Iran, on the northern coastline of the Persian Gulf. This area was established in 1998 for the utilization of south Pars field oil and gas resources. This field is one of the largest gas resources in the world and contains about 6% of the total fossil fuels known. Petrochemical industries, gas refineries and downstream industries are being constructed in this area. At present there are three gas refineries in operation and five more gas refineries are under construction. In this study, different types of solid waste including municipal solid waste (MSW) and industrial wastes were investigated separately. The aim of the study was to focus on the management of the industrial wastes in order to minimize the environmental impact. In the first stage, the types and amounts of industrial waste in PSEEZ were evaluated by an inventory. The main types of industrial waste are oil products (fuel oil, light oil, lubricating oil), spent catalysts, adsorbents, resins, coke, wax and packaging materials. The waste management of PSEEZ is quite complex because of the different types of industry and the diversity of industrial residues. In some cases recycling/reuse of waste is the best option, but treatment and disposal are also necessary tools. Recently a design has been prepared for a disposal site in PSEEZ for the industrial waste that cannot be reused or recycled. The total surface area of this disposal site where the industrial waste should be tipped for the next 20 years was estimated to be about 42 000 m2.     

Composition and production rate of dental solid waste in Xanthi, Greece: variability among dentist groups

The objective of this work was to determine the composition and production rate of dental solid waste, produced by dental practices in the Prefecture of Xanthi, a multicultural area in Northeast Greece with a population of 102,000. For the study, 22 private dental practices and 1 public dental practice were selected of the 48 private and 5 public dental practices in operation. The 22 private dental practices included 16 owned by Christian Greek-born dentists, 3 by Moslem dentists and 3 by Christian dentists repatriated from the former Soviet Union. Differentiation on the basis of religion is directly related to the countries from which dentists received their training, e.g., Greece-European Union, Turkey and former Soviet Union. Thus, including the one public dental practice, 4 study groups were considered. Waste collection took place for 22 working days, from 20 May to 27 June 2002. This period was considered to be a representative one for a semi-rural area, such as Xanthi. Dentists were instructed to collect the total amount of waste they produced. A total of 260 kg dental solid waste was collected during the study period and was manually separated. Dental solid waste was classified in three main categories: (1) Infectious and potentially infectious waste, accounting for 94.7% by weight. (2) Non-infectious waste accounting for 2.0%. (3) Domestic-type waste, accounting for 3.3% by weight. The category of infectious waste is classified as hazardous and includes components containing metal (8.51%), components without metal (91.18%) and amalgam (0.33%). Using the weight data, the production rate of dental solid waste for the study period in the Prefecture of Xanthi was determined to be 513 g/practice/day and of infectious and potentially infectious waste 486 g/practice/day. The latter includes the production rate of sharps (9.8 g/practice/day), non-sharps (31.6), infectious waste without metal (443) and amalgam (1.6 g/practice/day). Since dental solid waste is currently disposed of in landfills together with the municipal solid waste, the results of the study were used to suggest an appropriate management scheme. The results were also used to compare the composition and production rates of dental solid waste produced by the 4 study groups.     

Use of mix of clay/solid waste from steel works for civil construction materials.

The present study focuses on the use of solid waste generated by the steel works in Brazil for manufacturing clay-based structural products. The waste sample was characterized regarding chemical composition, X-ray diffraction, particle size, morphology, specific surface and plastic properties. The waste was added in gradual proportions to a kaolinitic clay from zero up to 3 wt.%. Ceramic bodies were formed by vacuum extrusion and fired at 950 degrees C. The physical-mechanical properties (linear shrinkage, water absorption, apparent density and flexural strength) of the resulting clay/solid waste mixtures were determined. In addition, leaching tests were performed according Brazilian Standards as well as a preliminary analysis of gases evolved during the thermal process. It was found that the solid waste is formed by irregular particles, ranging in size from 1 to 500 microm. The test results indicate that solid wastes generated by steel works can be used as filler in construction materials, thereby increasing reuse in an environmentally safe manner.     

Perspectives for integrated municipal solid waste management in Thessaloniki, Greece

Local authorities need updated and reliable data on the quantity and the quality of the waste generated in their area, in order to establish an integrated solid waste management system capable of fulfilling regional and national waste management targets. This paper presents information about the quantity and the characteristics of the municipal solid waste generated in Thessaloniki, which is the second largest city in Greece. It is based on the results of three research programs investigating the evolution of municipal solid waste. The investigations were carried out over the last 20 years at the landfill of Thessaloniki by the same research group using statistically acceptable practices for sampling and hand sorting. The results show a great increase in the incoming quantities during the last years and a significant increase of the per capita generation. There is also a significant change in the composition, demonstrated mainly by a decrease in the organic fraction followed by an increase of packaging materials (paper and plastic).