Historical record and sources of polycyclic aromatic hydrocarbons in core sediments from the Yangtze Estuary, China

Polycyclic aromatic hydrocarbons (PAHs) in a sediment core taken from intertidal flat in the Yangtze Estuary were determined by gas chromatography-mass spectrometry. The results indicate that the total concentration of PAHs ranged from 0.08 to 11.74 microg/g. The concentration levels of total and individual PAHs changed dramatically with depth. The concentrations of PAHs were relatively high above 35 cm depth and remained constantly low below this depth. The historical record of PAHs in the core shows subsurface maximum (one or more peak values), followed by decreased levels to the surface and with depth. And, PAH sediment record in the core profile is in agreement with historically sewage discharge events during the 1980s to 1990s. The distribution of target molecule acenephthene, the fluoranthene/pyrene ratio, the proportion of 2-3-ring and 4-5-ring PAHs, and alkylated naphthalene to parent naphthalene in the core profile show that the sources in this area are characterized by petroleum-derived PAH contamination (mainly sewage discharge and the river runoff) and the incorporation of atmospheric inputs. Studies indicate the PAH profile pattern in this site in comparison with other regions appear to reflect its particular local position (near the sewage outlet). Moreover, physico-chemical conditions and sedimentation rate as well as biodegradation also affect the PAH concentration levels in the core sediments.     

Long-range transport of polycyclic aromatic hydrocarbons from China to Japan

Airborne particulate matter was collected at Wajima, on the Noto Peninsula, Ishikawa, Japan by a high-volume air sampler with a quartz filter every week from 17 September 2004 to 16 September 2005. Polycyclic aromatic hydrocarbons (PAHs) extracted from filters were analyzed by HPLC with fluorescence detection. The atmospheric concentrations of PAHs at Wajima were higher during the heating period of China (when coal is burned for heat) than during the no-heating period. A meteorological analysis indicated that the air samples collected in that heating period at Wajima were transported mainly from Northeast China over the Japan Sea. Principal component analysis of nine PAHs indicated a Chinese origin of the PAHs. These results strongly suggest that the high-level PAHs detected at Wajima were the result of long-range transport from China.     

Relative decay index and sources of polycyclic aromatic hydrocarbons

An optimized method for the analysis of polycyclic aromatic hydrocarbons (PAH) in atmospheric aerosols with short sampling times (1h) has been used to determine the daily variations of PAH in the atmosphere. Of the various physicochemical parameters controlling the disappearance of PAH, the most important seem to be the thermic dependence and the chemical reactions with gaseous pollutants (NO_x, O₃, HNO₃, OH). The RDI is used to identify the different sources of urban pollution: domestic heating, vehicle traffic (petrol and diesel), refineries, foundries, incinerators and power stations (coal, gas and oil) and to quantify the results for standard conditions. The characteristic concentration ratios from each source are often different from those in the literature, where the data are based on long sampling times and are affected by PAH reactivity differences. The results obtained are parameters for setting up a mathematical model for calculating concentrations of PAH at any receptor site.     

Distribution and sources of polycyclic aromatic hydrocarbons (PAHs) in sediment from the upper reach of Huaihe River,East China

Introduction  

To assess the status of polycyclic aromatic hydrocarbons (PAHs) contamination in sediments from the upper reach of Huaihe River, East China, 16 surface sediment samples were collected in March 2007 and analyzed for 16 USEPA priority PAHs.     

多环芳烃在低氧沉积物环境中的分布状况

低氧环境普遍存在于底层水体以及表层沉积物中,随着中国水体有机污染加剧,低氧现象将越来越明显.有研究表明,中国水体普遍受到多环芳烃污染,由于其强烈的憎水性和低溶解性,大部分多环芳烃沉积在底泥中.总结了学者们对国内外河流、湿地、河口等水体沉积物中多环芳烃污染的研究成果,探讨了多环芳烃的分布规律,发现沉积物中多环芳烃含量与流域内经济发展状况密切相关,反映了经济发展过程对环境造成的负面影响.相比于国外典型区域的多环芳烃浓度,中国沉积物的多环芳烃污染处于中等水平,但处于快速上升阶段,部分点位浓度已超过生态风险区间低值(4 000 ng/g),对人们的身体健康构成威胁,所以对多环芳烃的生态风险评价、污染物排放控制需进一步加强.     

Anaerobic degradation of five polycyclic aromatic hydrocarbons from river sediment in Taiwan

This study investigated the anaerobic degradation of five polycyclic aromatic hydrocarbons (PAHs) from Erren River sediment in southern Taiwan. The degradation rates of PAH were in the order: acenaphthene > fluorene > phenanthrene > anthracene > pyrene. The degradation rate was enhanced when the five compounds were present simultaneously in river sediment. Comparison of the PAH degradation rates under three reducing conditions showed the following order: sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The addition of electron donors (acetate, lactate and pyruvate) enhanced PAH degradation under methanogenic and sulfate-reducing conditions. However, the addition of acetate, lactate or pyruvate inhibited PAH degradation under nitrate-reducing conditions. The addition of heavy metals, nonylphenol and phthalate esters (PAEs) inhibited PAH degradation. Our results show that sulfate-reducing bacteria, methanogen and eubacteria are involved in the degradation of PAH; sulfate-reducing bacteria constitute a major microbial component in PAH degradation. Of the microorganism strains isolated from the sediment samples, we found that strain ER9 expressed the greatest biodegrading ability.     

Anaerobic degradation of five polycyclic aromatic hydrocarbons from river sediment in Taiwan

This study investigated the anaerobic degradation of five polycyclic aromatic hydrocarbons (PAHs) from Erren River sediment in southern Taiwan. The degradation rates of PAH were in the order: acenaphthene > fluorene > phenanthrene > anthracene > pyrene. The degradation rate was enhanced when the five compounds were present simultaneously in river sediment. Comparison of the PAH degradation rates under three reducing conditions showed the following order: sulfate-reducing conditions > methanogenic conditions > nitrate-reducing conditions. The addition of electron donors (acetate, lactate and pyruvate) enhanced PAH degradation under methanogenic and sulfate-reducing conditions. However, the addition of acetate, lactate or pyruvate inhibited PAH degradation under nitrate-reducing conditions. The addition of heavy metals, nonylphenol and phthalate esters (PAEs) inhibited PAH degradation. Our results show that sulfate-reducing bacteria, methanogen and eubacteria are involved in the degradation of PAH; sulfate-reducing bacteria constitute a major microbial component in PAH degradation. Of the microorganism strains isolated from the sediment samples, we found that strain ER9 expressed the greatest biodegrading ability.     

Studies on polycyclic aromatic hydrocarbons in two sediment cores from the huaxi reservoir,china: Assessment of levels,sources, and ecological risk

This study investigated the levels, sources and ecological risks of 16 polycyclic aromatic hydrocarbons (PAHs) in two sediment cores that were collected along the Huaxi Reservoir. The spatial distributions and residue levels of the 16 priority PAHs in the sediments from the Huaxi Reservoir were analyzed for their potential ecological risk, source apportionment and contribution to the total PAH residue. The concentration level of the total PAHs (TPAHs) was in the range 1805 ng·g^?1 to 20023 ng·g^?1 based on dry weight, and the content of PAHs in the Huaxi Reservoir exhibited a gradual upward trend. The PAH congener ratios fluoranthene/(fluoranthene + pyrene) and indeno[1, 2, 3-cd]pyrene/(indeno[1, 2, 3-cd]pyrene + benzo[g, h, i]perylene) were used to identify the source. The main source of the low molecular weight PAHs was wood and coal combustion, whereas the high molecular weight PAHs were primarily from petroleum combustion sources. The results of an ecological risk assessment demonstrated that ACE poses a potential ecological risk, while FLU, NAP, ANT, BaP, DBA, PHEN and PYR can have serious ecological risks.     

Removal of sorbed polycyclic aromatic hydrocarbons from soil, sludge and sediment samples using the Fenton's reagent process

The use of the Fenton's reagent process has been investigated for the remediation of environmental matrices contaminated by polycyclic aromatic hydrocarbons (PAHs). Laboratory experiments were first conducted in aqueous solutions, to study the kinetics of oxidation and adsorption of PAHs. Benzo[a]pyrene was more rapidly degraded than adsorbed, while only partial oxidation of fluoranthene occurred. In the case of benzo[b]fluoranthene, its adsorption prevented its oxidation. Besides competition effects between PAHs were found, with slower oxidation of mixtures as compared to single PAH solutions. Apparition of some by-products was observed, and a di-hydroxylated derivative of benzo[a]pyrene could be identified under our conditions. Consequently, application to solid environmental matrices (soil, sludge and sediment samples) was performed using large amounts of reagents. The efficiency of the Fenton treatment was dependent on the matrix characteristics (such as its organic carbon content) and the PAH availability (correlated to the date and level of contamination). However, no pH adjustment was required, as well as no iron addition due to the presence of iron oxides in the solid matrices, suggesting the potential application of Fenton-like treatment for the remediation of PAH-contaminated environmental solids.     

Comparison of polycyclic aromatic hydrocarbons and nitropolycyclic aromatic hydrocarbons in airborne particulates collected in downtown and suburban Kanazawa,Japan

In this study, airborne particulates were collected at three sites, two in a downtown area and the other in a suburban area of Kanazawa, Japan in each season for 7 years. Two polycyclic aromatic hydrocarbons (PAHs), pyrene (Py) and benzo[a]pyrene (BaP) and four nitropolycyclic aromatic hydrocarbons (NPAHs), 1-nitropyrene (NP) and 1,3-, 1,6-, and 1,8-dinitropyrenes (DNP) were determined by high-performance liquid chromatography with fluorescence and chemiluminescence detection. At the downtown sites, the mean concentration of each DNP was about two orders of magnitude lower than that of 1-NP and more than three orders of magnitude lower than those of Py and BaP. This tendency reflected the composition of PAHs and NPAHs in diesel-engine exhaust particulates. Concentrations of these PAHs and NPAHs were higher at the downtown sites than at the suburban site, suggesting the dilution of these compounds during the transportation from the downtown to the suburban area. The concentration ratios of NPAHs to PAHs were larger at the downtown sites than at the suburban site. Studies using UV light and sunlight showed that degradation of NPAHs was faster than that of PAHs. Thus, the lower concentrations of NPAHs in the suburban sites may be due to their being photodegraded faster than PAHs during the atmospheric transportation from the downtown area to the suburban area.     

Mobile sources of atmospheric polycyclic aromatic hydrocarbons in a roadway tunnel

Amounts of polycyclic aromatic hydrocarbons (PAHs) and oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) in samples collected from the air, from the dust on a guardrail, and from the soils on a tunnel roadway at five sampling sites in a regular roadway tunnel were chemically analyzed in order to determine their sources. Among the 23 PAHs found in the air samples, pyrene was found in the highest concentration (43±7.2 ng/m³), followed by fluoranthene (26±4.3 ng/m³). Among 20 oxy-PAHs found in the air samples, anthraquinone was found in the greatest amount (56±3.9 ng/m³). The average concentration of the major PAHs found in the guardrail dust samples were 6.9±0.77 μg/g for pyrene, 5.5±0.76 μg/g for fluoranthene, and 2.6±0.30 μg/g for phenanthrene. The average concentration of the major oxy-PAHs found in the guardrail dust samples were 9.2±3.5 μg/g for anthraquinone and 1.4±0.50 μg/g for 2-methylanthraquinone. The average concentration of the major PAHs found in the soil samples were 1.1±0.31 μg/g for fluoranthene, 0.92±0.21 μg/g for pyrene, and 0.72±0.16 μg/g for phenanthrene. The average concentration of the major oxy-PAHs found in the soil samples were 1.2±0.88 μg/g for anthraquinone, 0.18±0.04 μg/g for 4-biphenylcarboxaldehyde, and 0.13±0.08 μg/g for 2-methylanthraquinone. The BeP ratios calculated from the results suggest that most PAHs found in the samples collected from the roadway tunnel were from automobile exhaust gases.     

Chemical characterization and source identification of polycyclic aromatic hydrocarbons in aerosols originating from different sources

To obtain the characteristic factors or signatures of particulate polycyclic aromatic hydrocarbons (PAHs) to help identify the sources of particulate PAHs in the atmosphere, different carbonaceous aerosols were generated by burning different fossil fuels and biomass under different conditions in the laboratory, and the chemical characteristics of 14 PAHs were studied in detail. The results showed that (1) carbonaceous aerosols derived from domestic burning of coal, diesel fuel, and gasoline have much higher concentrations of PAHs than those derived from domestic burning of biomass; (2) carbonaceous aerosols derived from domestic burning of diesel fuel/gasoline have similar PAH components as those derived from high-temperature combustion of diesel fuel/gasoline, although the former have much higher concentrations of PAHs than the latter, suggesting that the burning temperature obviously affects the emitting amount of particulate PAHs, but only slightly influences the PAHs components; and (3) the ratios of benzo[b]fluoranthene/acenaphthylene, benzo[b]fluoranthene/fluorene, dibenzo[a,h]anthracene/acenaphthylene, dibenzo[a,h]anthracene/fluorine, and benzo[b]fluoranthene/benzo[k]fluoranthene in carbonaceous aerosols are sensitively dependent on their sources, indicating that these ratios are suitable for use as characteristic factors or signatures of particulate PAHs in the atmosphere.     

Petroleum hydrocarbons and polycyclic aromatic hydrocarbons in the surficial sediments of Xiamen Harbour and Yuan Dan Lake, China

Surficial sediments were sampled from nine stations in Xiamen Harbour and two stations in Yuan Dan Lake during April 2002. Sediment samples were extracted by organic solvents, separated by silica gel column chromatography and analyzed by gas chromatography-mass selective detector (GC-MSD). Selected ion monitoring was at M/Z=57 for petroleum hydrocarbons (PHCs) and individual M/Zs for each of the 15 typical polycyclic aromatic hydrocarbons (PAHs) and nine alkylated PAHs. The results showed that concentrations of PHCs and total PAHs in the sediments of Yuan Dan Lake were 1397 microg g(-1) (dry weight, dw) and 1377 ng g(-1) (dw), respectively. The ranges for PHCs and total PAHs in the sediments from Xiamen Harbour were 133-943 microg g(-1) (dw) and 98-309 ng g(-1) (dw), respectively. Shipping activities, industrial wastewater discharges, fuel oil spillage from ships and vehicles were the main sources of PHCs and PAHs in the Harbour. In addition, the widespread use of coal for industrial processes and domestic consumption accounted for the second largest source of PAHs in the sediments, while atmospheric transport and deposition of PAHs are also important.     

Distribution of polycyclic aromatic hydrocarbons in water, suspended particulate matter and sediment from Daliao River watershed, China

This study investigated the spatial distribution of polycyclic aromatic hydrocarbons (PAHs) in surface water, suspended particulate matter (SPM) and sediment of Daliao River watershed composed of the Hun River, Taizi River, and Daliao River. The sources of PAHs were evaluated employing ratios of specific PAHs compounds and principal component analysis (PCA). The total concentrations of PAHs ranged from 946.1 to 13448.5 ng l(-1) in surface water, from 317.5 to 238518.7 ng g(-1) dry weight in SPM, and from 61.9 to 840.5 ng g(-1) dry weight in sediments. The levels of PAHs are relatively higher in water and SPM, and lower in sediments, in comparison with those reported for other rivers and marine systems around the world. The composition of PAHs in these mediums was mainly 4-6 rings PAHs. The higher contents of low molecular weight PAHs in the water and SPM suggest a relatively recent local source of PAHs, entered into the river via wastewater discharge and atmospheric way. On the other hand, the heavy pollution of PAHs in sediment and water near heavy industrial area suggests that PAHs have been released from industrial wastewater.     

Release of polycyclic aromatic hydrocarbons from Yangtze River sediment cores during periods of simulated resuspension

The role of resuspension duration on release of 16 PAHs was measured experimentally using a particle entrainment simulator (PES). Three sediment cores were resuspended for 12h at 0.2 and 0.5N m(-2). PAHs in water column and total suspended solids (TSS) were monitored at intervals. After 0.25h of resuspension, PAH release was on average 42% of their concentrations after 12h of resuspension, indicating fast release of PAHs from sediments in an initial short time. Moreover, PAHs released faster at 0.5N m(-2) than at 0.2N m(-2); low molecular weight PAHs (2-3-ring) released faster than median molecular weight (4-ring) PAHs. PAH concentrations in TSS showed generally increase with time and differences in magnitudes based on sediment type and energy. Overall, the composition of sediments is the major factor in determining the amount of released PAHs, more so than the level of resuspension energy applied.     

Pollution sources identification of polycyclic aromatic hydrocarbons of soils in Tianjin area, China

A total of 188 surface soil samples were collected from different types of utilization soils in Tianjin area. Factor analysis and scatter point surface tension spine function interpolation were used to analyze types and spatial distributions of PAH sources of surface soils in Tianjin area. The results showed that most pollution sources were mixed sources including coal burning and petroleum spill. Mixed sources occupied 56.12%, 58.96%, 46.45% and 59.50% in farmland of wastewater irrigation, common farmland, wild land and city greenbelt, respectively. Other pollution sources such as vehicle emission, biogenic conversion, wood burning and natural gas combustion were also significant. The spatial distributions of pollution sources were closely related to geographic location, geographic condition and living habit of indigenes.     

Analysis of polycyclic aromatic hydrocarbons in sediment reference materials by microwave-assisted extraction

The microwave-assisted extraction (MAE) of polycyclic aromatic hydrocarbons (PAHs) from harbor sediment reference material EC-1, marine sediment reference material HS-2 and PAH-spiked river bed soil was conducted. The extraction conditions for EC-1 were carried out at 70 degrees C and 100 degrees C under pressure in closed vessels with cyclohexane acetone (1:1), cyclohexane-water (3:1), hexane acetone (1:1), and hexane-water (3:1) for 10 min. A comparison between MAE and a 16-h Soxhlet extraction (SX) method showed that both techniques gave comparable results with certified values. MAE has advantages over the currently used Soxhlet technique due to a faster extraction time and lower quantity of solvent used. The consumption of organic solvent of the microwave method was less than one-tenth compared to Soxhlet.     

Size- and density-distributions and sources of polycyclic aromatic hydrocarbons in urban road dust

Polycyclic aromatic hydrocarbons (PAHs) present in size- and density-fractionated road dust were measured to identify the important fractions in urban runoff and to analyse their sources. Road dust was collected from a residential area (Shakujii) and a heavy traffic area (Hongo Street). The sampling of road dust from the residential area was conducted twice in different seasons (autumn and winter). The collected road dust was separated into three or four size-fractions and further fractionated into light (<1.7 g/cm3) and heavy (>1.7 g/cm3) fractions by using cesium chloride solution. Light particles constituted only 4.0+/-1.4%, 0.69+/-0.03% and 3.4+/-1.0% of the road dust by weight for Shakujii (November), Shakujii (February) and Hongo Street, respectively but contained 28+/-10%, 33+/-3% and 44+/-8% of the total PAHs, respectively. The PAH contents in the light fractions were 1-2 orders of magnitude higher than those in the heavy fractions. In the light fractions, the 12PAH contents in February were significantly higher than the 12PAH contents in November (P<0.01), whereas in the heavy fractions, no significant difference was found (P>0.05). Cluster analysis revealed that there was a significant difference in the PAH profiles between locations rather than between size-fractions, density-fractions and sampling times. Multiple regression analysis indicated that asphalt/pavement was the major source of Shakujii road dust, and that tyre and diesel vehicle exhaust were the major sources of finer and coarser fractions collected from Hongo Street road dust, respectively.     

Volatilization of polycyclic aromatic hydrocarbons from coal-tar-sealed pavement

The effects of the herbicide atrazine on the gill of the freshwater fish Prochilodus lineatus were evaluated after exposure of fish to 2, 10 and 25 μg L⁻¹ atrazine during 48 h (acute exposure) and 14 d (subchronic exposure). Ions and osmolality were measured in plasma and gill samples were taken to determine the Na⁺/K⁺-ATPase (NKA) and carbonic anhydrase (CA) activities and for morphological analysis. Plasma osmolality and Na⁺ and Cl⁻ ions changed depending on atrazine concentration, but atrazine exposure had no effect on the Na⁺/Cl⁻ ratio. NKA activity did not change after atrazine exposure, but CA activity decreased in fish exposed to 25 μg L⁻¹ for 14 d. Gill MRC density decreased after acute exposure but did not change in fish exposed to the subchronic treatment. The MRC density at the epithelial surface increased in fish exposed to 25 μg L⁻¹, and the MRC fractional area (MRCFA) increased in fish exposed to 10 μg L⁻¹. The changes in MRCs provide evidence of morphological adjustments to maintain ionic homeostasis in spite of the inhibition of CA activity at the highest atrazine concentration.