Distribution and contamination assessment of heavy metals in sediment of the Second Songhua River, China

The Second Songhua River was subjected to a large amount of raw or primary effluent from chemical industries in Jilin city in 1960s to 1970s, resulting in serious mercury pollution. However, an understanding of other trace metal pollution has remained unclear. The objective of this study was to investigate trace metal contamination in the sediment of the river. Bottom sediment samples were taken in the river between Jilin city and Haerbin city in 2005. An uncontaminated sediment profile was taken in the Nen River at the same time. Total concentrations of Al, Fe, Mg, Ca, K, Na, Ti, Mn, V, Sc, Co, Cu, Cr, Ni, Pb and Zn in the sediment samples were measured by ICP-MS or ICP-OES, following digestion with various acids. Concentrations of Co, Cu, Cr, Ni, Pb and Zn in the surface sediments were 5.1–14.7, 18.5–78.9, 2.4–75.4, 7.2–29.0, 13.5–124.4, and 21.8–403.1 mg/kg, respectively, generally decreasing along the course of the river from Jilin city to Haerbin city. Background concentrations of trace metals were reconstructed by geochemical normalization to a conservative element scandium. Results showed that concentrations of Co, Cr, and Ni in the sediment were generally only slightly higher than or equal to their background values, while concentrations of Cu, Pb, and Zn in the some sediment samples were significantly higher than their background values. In detail, the sediment at Jilin city was moderately contaminated by Cu, and the sediment of the Second Songhua River was moderately contaminated by Pb and Zn. The top layer (0–10 cm depth) and bottom layers (30–46 cm depth) of one sediment profile at Wukeshu town were generally moderately polluted by Pb and Zn. Synthetically, the surface sediment in the studied river section was classified as natural sediment without ecological risk by the sediment pollution index (SPI) of Cu, Cr, Ni, Pb and Zn. Only the 30–45 cm depth of the sediment profile at Wukeshu town was classified as low polluted sediment by the SPI of these metals, recording a historical contamination of the river in the 1960s to 1970s. This buried contamination of trace metals might pose a potential risk to water column under disturbance of sediment. Foundation item: The National Basic Research Priorities Program of China (2004CB418502)     

Sources and distribution of trace metals in the saricay stream basin of southwestern turkey

Seasonal variation of the concentrations of trace metals (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb and Zn) were measured by ICP-AES in the water and sediment from the Saricay Stream, Geyik Dam and Ortakoy Well in the same basin. Comparisons between trace metal concentrations in water and sediment in three sources (Stream, Dam and Well) were made. The concentrations of a large number of trace metals in the water and sediment were generally higher in the Stream than in the Well and Dam, particularly in summer. Trace metal concentration ranges in sediments of the Saricay Stream and its sources showed very wide ranges (as mass ratio): Co: 5–476 μg g⁻¹, Cr: 15–1308 μg g⁻¹, Cu: 7–128 μg g⁻¹, Fe: 1120–13210 μg g⁻¹, Mn: 150–2613 μg g⁻¹, Ni: 102–390 μg g⁻¹, Pb: 0.7–31.3 μg g⁻¹ and Zn: 18–304 μg g⁻¹, whereas Cd was not detected. Trace metal concentration ranges found in waters were: Co: 9.5–20.7 μg L⁻¹, Cr: 20.3–284 μg L⁻¹, Cu: 170–840 μg L⁻¹, Fe: 176–1830 μg L⁻¹, Mn: 29.3–387 μg L⁻¹, and Ni: 4.3–21.9 μg L⁻¹. Among the trace metals studied, Cd and Zn in two seasons and Pb in winter were usually not detected or in the recommended levels. In addition, Cd was not detected in the sediment during the winter season. The analysis of variance (one-way ANOVA) and correlation matrix was employed for the sediment and water samples of the two field surveys (summer and winter) comparison. The three sources showed differences in metal contents. The metal levels in sediments displayed marked seasonal and regional variations, which were attributed to anthropogenic influences and natural processes. In the Saricay Stream, high values of metals during the dry season showed an anthropological effect from small industry firms, e.g.: an olive mill and a dairy farm or water dilution during summer seasons. Finally, the pollution in this basin probably originated from small industrial, low quality coal-burned thermal power plants, and particularly agricultural and domestic waste discharges.     

Metal Pollution Assessment of Sediment and Water in the River Hindon, India

The metal pollution in water and sediment of the River Hindon in western Uttar Pradesh (India) was assessed for Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn. The metal concentrations in water showed wide temporal variation compared with bed sediment because of variability in water discharge and variations in suspended solid loadings. Metal concentrations in bed sediments provided a better evaluation of the degree and the extent of contamination in the aquatic environment, Santagarh and Atali being the most polluted sites of the river. The ratio of heavy metals to conservative elements (Fe, Al, etc.) may reveal the geochemical imbalances due to the elevated metal concentrations normally attributed to anthropogenic sources. Metal/Al ratios for the bed sediments of the river Hindon were used to determine the relative mobility and general trend of relative mobility occurred Fe > Mn > Zn > Cr > Ni > Pb > Cu > Cd.     

Source discrimination of heavy metals in sediment and water of To Lich River in Hanoi City using multivariate statistical approaches

The concentrations of Mn, Fe, Ni, Cr, Cu, Pb, Zn, As, and Cd were determined to evaluate the level of contamination of To Lich River in Hanoi City. All metal concentrations in 0–10-cm water samples, except Mn, were lower than the maximum permitted concentration for irrigation water standard. Meanwhile, concentrations of As, Cd, and Zn in 0–30-cm sediments were likely to have adverse effects on agriculture and aquatic life. Sediment pollution assessment was undertaken using enrichment factor and geoaccumulation index (I _geo). The I _geo results indicated that the sediment was not polluted with Cr, Mn, Fe, and Ni, and the pollution level increased in the order of Cu < Pb < Zn < As < Cd. Meanwhile, significant enrichment was shown for Cd, As, Zn, and Pb. Cluster and principal component analyses suggest that As and Mn in sediment were derived from both lithogenic and anthropogenic sources, while Cu, Pb, Zn, Cr, Cd, and Ni originated from anthropogenic sources such as vehicular fumes for Pb and metallic discharge from industrial sources and fertilizer application for other metals.     

A case study of trace metals in suspended particulate matter and biota before wastewater treatment plant from the Izmir Bay,Turkey

The concentrations of trace metals (Cu, Zn, Mn, Ni, and Fe) from suspended particulate matter (SPM) and biota in Izmir Bay (Eastern Aegean Sea) were studied in order to evaluate the environmental impact of the anthropogenic metals before building of Wastewater Treatment Plant. SPM samples were collected in wet and dry periods from Izmir Bay. Metal concentrations in SPM (Cu, 0.36–2.19; Mn, 0.07–11.3; Ni, 0.43–7.81; Zn, 7.33–269; Fe, 1.00–266 μgdm^− 3) were comparable to those reported for other moderately polluted bays. Maximum metal concentrations in SPM were observed during summer season. SPM metal concentrations displayed a clear spatial trend with values increasing with proximity to urban centers. Cu and Zn concentrations in SPM were especially high in the inner bay. SPM were found to be contaminated by Zn. The vertical profile of Mn, Zn, and Ni concentrations in SPM had a maximal value at the upper layer and decreased to minimal value at the bottom layer of the inner bay in summer, in contrast to the observed pattern of Fe and Cu. Maximum Cu concentrations were obtained in Penaeus kerathurus. Also, maximum Zn and Fe concentrations were found in Mytilus galloprovincialis. Relatively high Cu levels were found in Sardina pilcardus and Mullus barbatus than other fish species. Besides, Cu levels were lower in Diplodus annularis and Merluccius merluccius. Finally, metal levels in biota tissues were lower than the limits of European Dietary Standards and Guidelines.     

Spatial distribution and human contamination quantification of trace metals and phosphorus in the sediments of Chaohu Lake,a eutrophic shallow lake,China

Distinguishing and quantifying anthropogenic trace metals and phosphorus accumulated in sediment is important for the protection of our aquatic ecosystems. Here, anthropogenic proportion and potential sources of trace metals and phosphorus in surface sediments of Chaohu Lake were evaluated based on the exhaustive geochemical data. The analysis shows that concentrations of major and trace metals, and phosphorus, displayed significant spatial diversity and almost all elements were over the pre-industrial background value, which should be related to the variations of sediment composition partially. Therefore, conservative element normalization was introduced and calculated enrichment factors (EFs) of the elements were referenced highlighting the human contamination. EFs of the major and trace metals, except Zn, Pb, and Cu, were all nearly 1.0, indicating the detrital origin. The EFs of Zn, Pb, Cu and phosphorus were 1.0–10.4, 1.0–3.8, 1.0–4.9, and 1.0–7.6, respectively, showing moderate to significant contamination. Higher EFs of Zn, Pb and Cu occurred in the mouth areas of Nanfei River and Zhegao River, and they decreased to the lake center in the northwest and northeast lake areas, respectively. We deduced that anthropogenic Zn, Pb, and Cu were mainly from urban and industrial point sources and the non-point sources of atmospheric deposition contributed little to their contamination. The EFs of phosphorus showed similar spatial degradation with that of Zn, Pb, and Cu. Moreover, higher EFs (>1) of phosphorus also occurred in other areas adjacent to the river mouths besides Nanfei River and Zhegao River. This indicated that the non-point agricultural source may also be responsible for the contamination of phosphorus in Chaohu Lake in addition to the urban sewage sources. Anthropogenic phosphorus was mainly concentrated in the speciation of NaOH-P, which had higher potential biological effects than the detrital proportion. Concentrations of Zn, Pb and Cu surpassed the threshold effect concentrations (TEC) of consensus-based sediment quality guidelines of freshwater ecosystems, especially in the contaminated northwest area of Chaohu Lake. This highlighted the contributions of anthropogenic contamination to the elevated potential biological effects of trace metals. Though there had been no obvious human contamination of Cr and Ni in Chaohu Lake, concentrations were all over the TECs, which may be due to higher background levels in the parent materials of soils and bedrocks in Chaohu Lake catchment.     

Sediment and Suspended Matter Lead Contamination in the Gulf of Kavala, Greece

Sediment and suspended particulate matter samples from 24 stations in the Gulf of Kavala have been examined for lead contamination. Grain size analysis and organic matter content were also performed. Total – anthropogenic sediment lead concentrations and enrichment factors at stations close to harbors and chemical industries were found higher (up to 209–135μg/g and 4.12 respectively), in relation to concentrations from the rest of the coastal zone. In the above areas, increased suspended particulate lead in the bottom of the water column was also recorded (up to 109μg/g). Total sediment lead concentrations composed of high natural Pb background increased with decreasing grain size, suggesting their association with the fine fractions of the sediments (31.1–66.0% mud presence) and the organic matter content (6–9% higher values). Overall, higher total lead concentrations in the sediments, determined by this work, appear to be significantly different from those reported for the Gulf of Kavala in previous studies and similar to those detected in other highly contaminated eastern Mediterranean coastal areas.     

Assessment of heavy metal concentration in the Khoshk River water and sediment, Shiraz, Southwest Iran

Heavy metal contents and contamination characteristics of the water and sediment of the Khoshk River, Shiraz, Southwest Iran were investigated. The abundance of heavy metals decreases as Zn > Mn > Cr > Ni >Pb > Cu > Cd in water samples and Mn > Cr > Pb > Ni > Zn > Cu > Cd in sediments, respectively. Based on the enrichment factor and geoaccumulation index values, sediments were loaded with Cr, Zn, Pb, Cu, and Cd. Pearson correlation matrix as well as cluster and principal components analyses and analysis of variance were implemented on data from sampling sites. Based on the locations of sampling sites in clusters and variable concentrations at these stations, it was concluded that municipal, industrial, and domestic discharges in the Shiraz urban area strongly affected heavy metals concentrations in the Khoshk River water and sediment. Results obtained from principal components analysis of sediment samples showed that the high concentration of Ni was mainly from natural origin, related to the composition of parent rocks, while the elevated values of Cr, Zn, Pb, Cd, and Cu were due to anthropogenic activities.     

Distribution of heavy metals in the dissolved and suspended phase of the sea-surface microlayer, seawater column and in sediments of Singapore’s coastal environment

Concentrations of heavy metals were determined in the water column (including the sea-surface microlayer, subsurface, mid-depth and bottom water) and sediments from Singapore’s coastal environment. The concentration ranges for As, Cd, Cr, Cu, Ni, Pb and Zn in the seawater dissolved phase (DP) were 0.34–2.04, 0.013–0.109, 0.07–0.35, 0.23–1.16, 0.28–0.78, 0.009–0.062 and 0.97–3.66 μg L⁻¹ respectively. The ranges for Cd, Cr, Cu, Ni, Pb and Zn in the suspended particulate matter (SPM) were 0.16–0.73, 6.72–53.93, 12.87–118.29, 4.34–60.71, 1.10–6.08 and 43.09–370.49 μg g⁻¹, respectively. Heavy metal concentrations in sediments ranged between 0.054–0.217, 37.48–50.52, 6.30–21.01, 13.27–26.59, 24.14–37.28 and 48.20–62.36 μg g⁻¹ for Cd, Cr, Cu, Ni, Pb and Zn, respectively. The lowest concentrations of metals in the DP and SPM were most frequently found in the subsurface water while the highest concentrations were mostly observed in the SML and bottom water. Overall, heavy metals in both the dissolved and particulate fractions have depth profiles that show a decreasing trend of concentrations from the subsurface to the bottom water, indicating that the prevalence of metals is linked to the marine biological cycle. In comparison to data from Greece, Malaysia and USA, the levels of metals in the DP are considered to be low in Singapore. Higher concentrations of particulate metals were reported for the Northern Adriatic Sea and the Rhine/Meuse estuary in the Netherlands compared to values reported in this study. The marine sediments in Singapore are not heavily contaminated when compared to metal levels in marine sediments from other countries such as Thailand, Japan, Korea, Spain and China.     

Trace metal concentrations in suspended particles, sediments and clams (Ruditapes philippinarum) from Jiaozhou Bay of China

Suspended particulate matter (SPM), sediments and clams were collected at three sites in Jiaozhou Bay to assess the magnitude of trace metal pollution in the area. Metal concentrations in SPM (Cu: 40.11–203; Zn: 118–447; Pb: 50.1–132; Cd: 0.55–4.39; Cr: 147.6–288; Mn: 762−1670 μg/g), sediments (Cu: 17.64–34.26; Zn: 80.79–110; Pb: 24.57–49.59; Cd: 0.099–0.324; Cr: 41.6–88.1; Mn: 343−520μg/g) and bivalves (Cu: 6.41–19.76; Zn: 35.5–85.5; Pb: 0.31–1.01; Cd: 0.51–0.67; Mn: 27.45−67.6 μg/g) are comparable to those reported for other moderately polluted world environments. SPM showed a less clear pattern. Metal concentrations in sediments displayed a clear geographical trend with values increasing with proximity to major urban centers. The clams (on dry weight) showed a complex pattern due to the variability introduced by age-related factors. Cd showed an apparent reverse industrial trend with higher concentrations in clams collected at distant stations. Zn, Pb and Mn showed no clear geographical pattern, whereas Cu increased in the clams collected in the most industrialized area. In addition, the bioaccumulation factors (BAF) were calculated. The result indicated that the studied Ruditapes philippinarum in Jiaozhou Bay possessed different bioaccumulation capacities for Cd, Zn, Cu, Pb and Mn, and Cd, Zn had a relatively high assimilation of those metals from sediment particles. A significant relationship with clam age was observed for Zn (positive) and Cu (negative) suggesting different physiological requirements for both metals with age. Trace metal concentrations measured in the tissue of the investigated clam were in the range considered safe by the WHO for human use.     

Determination of heavy metals (Cd, Cr, Cu, Fe, Ni, Pb, Zn) by ICP-OES and their speciation in Algerian Mediterranean Sea sediments after a five-stage sequential extraction procedure

Surface sediment samples (n = 18) were collected from the Algerian Mediterranean coasts and analyzed for seven metals using inductively coupled plasma-optical emission spectrometry in order to asses the distribution and bioavailability of metals and to study the anthropogenic factors affecting their concentrations. Sediment samples were size-fractionated into three sizes: 1,080–500 (coarse), 500–250 (medium), and <250 mm (fine). Bulk sediments were subjected to both sequential extraction and total digestion to evaluate the reliability of the sequential extraction procedure (SEP), while the fractions have been only sequentially extracted for metals speciation. The metals were sequentially extracted into five phases namely exchangeable (P1), carbonates (P2), Fe–Mn oxides (P3), organic (P4) and residual (P5). Metal recoveries in sequential extractions were ±20% of the independently measured total metal concentrations; the high recovery rates indicate the good reliability of the SEP used in this study. Correlation coefficients indicated that the grain size has an effect on the distribution of metals in the investigated samples. The order of metal levels in the fractions was medium > fine > coarse for all the metals. The average total extractable metal concentrations for Cd, Cr, Cu, Fe, Ni, Pb, and Zn were 1.1, 8.8, 4.7, 1,291.3, 13.9, 5.7 and 20.4 μg/g, respectively. The northeastern shelf had the lowest metal levels while the highest were in northwestern part mainly due to the significant tourism activities in the northwestern part. Comparison of our results to Earth’s crust values and to previous studies points out that our samples were relatively unpolluted with respect to the heavy metals investigated; most of the metals are not from anthropogenic sources. Enrichment factors as the criteria for examining the impact of the anthropogenic sources of heavy metals were calculated, and it was observed that the investigated samples were not contaminated with Cr, Cu, and Fe, moderately contaminated with Ni, Pb, and Cd, and contaminated with Cd in some sites. The P5 phase had the highest percents of Cr, Cu, Fe, Ni, and Zn. Cadmium and lead were predominant in the P4 phase, while Cu, Fe and Zn were distributed in the order P5 > P3 > P4 > P2 > P1. The following order of bioavailability was found with the heavy metals Pb > Cr > Cd > Ni > Zn > Cu > Fe.     

Sorbed metals fractionation and risk assessment of release in river sediment and particulate matter

Fractionation of metals in natural sediment and suspended particulate matter (SPM) of Tadjan River is investigated. Competitive sorption, sorption capacities of sediment and SPM as well as fractionation of metal-loaded sediment and SPM are also examined. A risk assessment code (RAC) is applied to estimate the risk of heavy metals release into the environment during the sorption process. Results revealed that sediments and SPM containing more than 25 % of clay minerals and higher amounts of calcite have great capacity of metal sorption, particularly for Cu, Ni, and Mn. Assessing the risk of metals release prior to and following sorption tests indicates that RAC of metals would significantly increase from the level of no or low risk in natural sediment and SPM to high or very high risk after sorption. The Langmuir model reveals that the highest affinity for Cu, Mn, and Ni in sediment is the organic fraction. The classic isotherm models of Freundlich and Langmuir can fit the data from chemical extraction studies of adsorbed metals, indicating that although sorption was apparently a physical and chemical process in the river, isotherm models can be used to simulate the sorption and accumulation in different geochemical phases within the particulate matter.     

Heavy metal status of sediment in river Cauvery,Karnataka

The purpose of this research work was to appraise extent of heavy metals in sediment and the degree to which its quality tainted seasonally and spatially in river Cauvery. In this study, heavy metals such as Fe, Zn, Ni, Mn, Pb, Cu, Co, Cd and Cr were analysed in sediments. Results were compared with sediment quality guidelines from various derived criteria. Twenty-five sampling points were selected based on geographical proximity of agricultural fields and industrial discharges; river-tributary confluence points; settlements located along the river bank; ritual and recreational activities. Sampling was done for the period of 3 years (2007 to 2009). Digestion of the samples was done by microwave-assisted digestion technique. Analysis was carried out using flame furnace atomic absorption spectrophotometer, and results are expressed in micrograms per gram. The mean concentration of Fe (11144 μg/g) followed by Mn (1763.3 μg/g), Zn (93.1 μg/g), Cr (389 μg/g), Ni (27.7 μg/g), Cu (11.2 μg/g), Pb (4.3 μg/g), Co (1.9 μg/g) and Cd (1.3 μg/g) remained within the levels of sediment quality guidelines. Multivariate statistical techniques such as principal component analysis and cluster analysis (CA) were employed to better comprehend the controlling factors of sediment quality and spatial homogeneity among the stations. The sediment geo-accumulation index (I_geo) showed maximum value of Cd (2.69) and least value of Mn (−1.44). The geo-accumulation class (I_geo class) was in the sequence as follows: Cd>Zn>Pb>Cr>Cu>Co>Ni>Fe>Mn. Negative total geo-accumulation indices (I_tot) revealed that mean concentration of heavy metals in the river bed sediment are lower than their respective shale values. The statistical analysis of inter-metallic relationship revealed the high degree of correlation among the metals indicated their identical behaviour during transport. This study concludes that insignificant geo-accumulation with metals except Cd (moderate contamination), Pb and Zn (slight contamination) principally in downstream stretch may perhaps deteriorate the sediment quality due to intensification anthropogenic influences. It also proves that extent of existing metal concentrations in sediments of river Cauvery in Karnataka not exceeded the toxic limit, and there is no peril to the aquatic life.     

Distribution and accumulation of heavy metals in the sediments of Akkaya Dam,Nigde, Turkey

Twenty-one surface sediment samples were collected from Akkaya Dam. Heavy metal concentrations (Mo, Cu, Pb, Zn, Ni, Co, Mn, Fe, Cr, As, V and Cd), grain size, organic carbon and carbonate contents were studied in order to assess the extent of environmental pollution and to discuss the origin of these contaminants in sediments of dam. The sediments in the study area are mostly very fine sands. However, mud was observed in the northeast of the dam. Sediment pollution assessment was carried out using enrichment factor. The calculation of enrichment factors showed that Mo is depleted by 1.0 whereas Cu, Pb, Zn, Ni, Co, Mn, As, V, Cr and Cd are enriched by 3, 5.4, 7, 2.7, 2.2, 3.4, 42.3, 2.1, 1.8 and 7.2, respectively. Relatively high concentrations heavy metals occurred in north (textile industry area) and east (Karasu River) due to enrichment controlled by anthropogenic wastes. The results of correlation analysis show low–medium positive and negative correlations among metals, grain size, carbonate contents and organic carbon and indicate that heavy metals in sediments of the Akkaya Dam have different anthropogenic sources.     

Spatial Characterization and Prioritization of Heavy Metal Contaminated Soil-Water Resources in Peri-Urban Areas of National Capital Territory (NCT), Delhi

Due to rapid industrialization and urbanization during last two decades, contamination of soils by heavy metals is on an increase globally. Lands under peri-urban agriculture are the worst affected. In NCT, Delhi about 14.4% of land area is chemically degraded. In order to take care of this problem, recently the Supreme Court of India ordered to shift various non-confirming (about 39,000 units) industries to regions outside NCT, Delhi. However in spite of this, there have been several reports and parliamentary debates on the phyto-toxicity and extensive accumulation of heavy metals in the region. Literature review revealed that the basis of these debates is a few studies on some point locations in/around Delhi. It was further observed that information on the distribution and extent of heavy metal pollution problem in the region was completely missing. The present study was thus basically aimed at assessing the spatial distribution/extent and type of heavy metal pollution in the study area, for enabling future designing of appropriate site-specific management measures by the decision makers.For this, detailed spatial information on bio-available heavy metal concentrations in the soils and surface/sub-surface waters of NCT (Delhi) was generated through actual soil/water surveys, standard laboratory methods and GIS techniques. The study showed that concentration of all micronutrients (viz. Zn: 0.05–0.18 ppm; Cu: in traces; Fe: 0–0.5 ppm; and Mn: 0–1.2 ppm) and most heavy metals (viz. Ni: 0–0.7 ppm; Pb: 0–0.15 ppm and Cd: in traces) in the surface/sub-surface irrigation waters were well within permissible limits. However Cr concentrations in irrigation waters of Alipur and Shahdara blocks were far above their maximum permissible limit of 1 ppm. It was further observed that Ni and Cr concentrations in the drinking waters of almost entire test area were far above maximum permissible levels of 0.02 and 0.01 ppm, respectively. Bio-available concentrations of several heavy metals (viz. Pb: 0.1–2 ppm; Cd: traces; Ni: 0.05–2 ppm and Cr: 0–0.4 ppm) in the study area soils were also observed to be well within the maximum permissible limits. However there were point Cu contaminations (5–10 ppm) in the sewage-sludge amended soils of vegetable growing areas near south Shahdara block. This was attributed to increased Cu availability due to oxidized acidic conditions generated by over-irrigation of agricultural lands. Available Mn concentrations in Kanjhawala, western Najafgarh and Alipur soils were also observed to be above maximum permissible limit of 10 ppm. This was observed to be mainly due to the geology (i.e. presence of Mn rich sedimentary rocks) and prevalence of reduced acidic conditions, due to paddy cultivation, in these areas. It was further observed that there is acute zinc (Zn) deficiency (< 0.6 ppm) in paddy growing soils of north Kanjhawala, Alipur and some parts of Najafgarh and Shahdara blocks due to extensive leaching of available Zn fractions to lower soil horizons. Similar available Zn deficiencies in high pH (8.5) soils of areas around Bamnoli village in E-Najafgarh block were also observed.     

Heavy metals partitioning in sediments of the Kabini River in South India

Cu, Cr, Fe, Mn, Ni, Pb, and Zn in the sediments of the Kabini River, Karnataka, India was studied to determine the association of metal with various geochemical phases by sequential extraction. The variations of heavy metal concentration depend on the lithology of the river basin and partly on anthropogenic activities. The Kabini River sediments are dominated by Sargur supracrustals with amphibolites, gneisses, carbonates, and ultrabasic rocks weathering into gneissic and serpentine soils carrying a natural load of cationic heavy metals. The source of heavy metals in the Kabini riverbed sediments is normally envisaged as additional inputs from anthropogenic over and above natural and lithogenic sources. Geochemical study indicates the metals under study were present mostly in the least mobilizable fraction in the overlying water and it is concluded that heavy metals in these sediments are to a great extent derived from multisource anthropogenic inputs besides geochemical background contributions The results show that lead and chromium have higher potential for mobilization from the sediment due to higher concentration at the exchangeable ion and sulfide ion bounded, also Cu and Pb have the greatest percentage of carbonate fraction, it means that the study area received inputs from urban and industrial effluents. Association of the Fe with organic matter fraction can be explained by the high affinity of these elements for the humic substances. Further, Zn and Ni reveal a significant enrichment in sediment and it is due to release of industrial wastewater into the river. These trace metals are possible contaminants to enter into aquatic and food chain.     

Total and Leachable Heavy Metals in Muddy and Sandy Sediments of Egyptian Coast Along Mediterranean Sea

The assessment of marine pollution due to metals was made for surficial sediments sampled from 20 sites along Mediterranean coast of Egypt. The samples were dried, acid digested and analyzed for leachable and total heavy metal contents (Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) by flame atomic absorption spectrophotometer (air–acetylene) with deuterium background correction. Evaluation of the heavy metals pollution status was carried out using enrichment factors (EFs), the effect range-low (ERL) and the effect range-median (ERM). The study showed high concentrations of Cd, Co, Pb, Ni and moderate concentrations of Cr, Cu and Mn were contaminated in the sediments of studied sites. The results of Spearman correlation, factor and cluster analysis of the heavy metals analyzed in the collected sediment were discussed. The main source of contamination is the offshore oil field and industrial wastes, which arise due to the ineffective and inefficient operation equipments, illegal discharge and lack of supervision and prosecution of offenders.     

Organotin Compounds and Selected Metals in the Marine Environment of Northern Adriatic Sea

The extent of pollution with organotin compounds and Cd, Pb, Ni, Cu, Zn, Cr, Mn, V, Co and Al was investigated in sediments and mussels (Mytilus galloprovincialis) from the Slovenian costal area of the Northern Adriatic Sea. Sampling was performed in Marina Portorož, Dockyard Izola, non exposed area of the Bay of Mesečev zaliv and in Mariculture Sečovlje. Mussels were taken in the summer and winter time, while sediments were collected during the winter sampling. Organotin compounds were determined by gas chromatography—mass spectrometry and metals by flame or electrothermal atomic absorption spectrometry. The accuracies of the analytical procedures were checked by the analysis of standard reference materials CRM 477 mussel tissue and PACS 2 marine sediment (organotin compounds) and SRM 2976 mussel tissue and CRM 320 river sediment (metals). Good agreements between certified and determined values were obtained. Normalization procedure to Al was applied to estimate the anthropogenic inputs of metals in sediments. The analyses of sediments demonstrated moderate pollution with organotin compounds in Marina Portorož and in Dockyard Izola. Concentrations of tributyltin species were higher than those of dibutyltin and monobutyltin. In mussels substantial contamination with tributyltin was observed in Marina Porotrož and Dockyard Izola. The extent of pollution was higher in the winter time. The analysis of metals in sediments exhibited elevated concentrations in Marina Portorož and Dockyard Izola. Data from the normalization procedure indicated the anthropogenic inputs of Cu, Zn and Cr in Marina Portorož and Mn in Bay of Mesečev zaliv and Dockyard Izola. Mussels, as accumulators of pollutants, in general contained higher metal concentrations during winter time in Dockyard Izola.     

Heavy metals in water, sediment and tissues of Liza saliens from Esmoriz–Paramos lagoon, Portugal

Esmoriz–Paramos lagoon is an ecosystem of great ecological importance that is located on the northwest coast of Portugal and has been degraded as a result of industrial and anthropogenic activities. Concentrations of heavy metals (Cr, Cu, Pb and Zn) were measured in water, sediment and in tissues (liver and muscle) of Liza saliens, which is the dominant fish from the lagoon. Comparisons between metal concentrations in water and sediments were made with those in tissues of fish caught at the lagoon. Metals in water were quantified predominantly bound to particulate and equalled or exceeded the limit of chronic reference values. Metal concentrations in sediments varied among sampled sites. The relative order of concentrations was “Zn > Cu ∼ Pb > Cr” the same pattern observed for metals in water. Metals in fish tissues showed higher concentrations in liver (262 mg Cu·Kg⁻¹ and 89 mg Zn·Kg⁻¹) than in muscle (<3 mg Cu·Kg⁻¹ and 26 mg Zn·Kg⁻¹), while Pb and Cr were not detected. These results suggest that Cu and Zn are the metals of major concern in the lagoon. Mullet detritivorous feeding habits, bioaccumulation pattern and the high sediment metals concentrations relative to the water suggest that sediments can be the most important source of contamination in this ecosystem. The positive relationship found between Cu in liver and fish length demonstrates that time of exposure is a crucial factor in bioaccumulation. Condition indices (K and HSI) in mullets from the lagoon were higher compared to mullets from sea, suggesting abnormal condition in the lagoon population. We conclude that metals chronic exposure in the lagoon can impose considerable fish stress. The results also show that the lagoon is an area of environmental concern.     

Metal pollution records in core sediments of some Red Sea coastal areas, Kingdom of Saudi Arabia

In the last three decades, the industrial and human activities in the coastal area of Saudi Arabia have increased dramatically and resulted in the continuous invasion of different types of pollutants including heavy metals. Seven sediment cores were collected from three major industrialized areas; Jeddah, Rabigh and Yanbu, along the coast of Saudi Arabia to determine the spatial and temporal distribution of metals and to assess the magnitude of pollution and their potential biological effects. Sediments were analyzed for texture, calcium carbonate contents, organic matter and metals (Al, Fe, Mn, Cd, Cr, Cu, Ni, Pb and Zn). Some metals like, Cr, Mn, Ni and Zn, were enriched in the upper 15 cm of core samples (recent deposition of sediments). Cadmium concentrations showed high fluctuations with depth and reverse pattern to that for Al, Fe and Mn which indicated land based sources of this element to the studied areas. Elevated concentrations of lead were recorded in the bottom layers of cores in Jeddah that indicated the most dramatic increase in usage of gasoline in early 1970s. The calculated contamination factors (CF's) were found in the following sequences: Cd > Pb > Ni > Cu > Zn > Cr > Mn for all studied areas. Results of Pollution Load Index (PLI) revealed that Jeddah is the most polluted area, followed by Rabigh while Yanbu is the least contaminated area. Except for Ni, the concentrations of most metals in the majority of sediment samples were believed to be safe for living organisms. As no data were available on the concentration of metals in core sediments in the coastal area of Saudi Arabia, the results of this study would serve as a baseline against which future anthropogenic effects can be assessed.