基于参数环境影响评价探讨

基于参数与环境之间的关系,论述了将参数用于环境影响评价的可行性。提出通过修正标准参考环境而确定安全基准环境的理论,然后用参数来评价不同污染物的环境影响。阐述了火电厂系统、标准参考环境和安全基准环境三者之间的关系。     

智能电网与环境安全关系综述

智能电网技术可以将各种分布式再生能源迅速接入电网,对环境安全具有重要的促进作用。介绍了智能电网的发展现状及关键技术,从能源防御体系、土地利用和电力生产等方面对智能电网与环境安全之间的关系进行了分析。智能电网技术的兴起与发展可以真正做到减少碳的排放量,提高用电系统的抗击灾害能力,同时也可以有效的保护环境、集约利用土地。智能电网技术是将来电力环境安全体系中重要的组成环节。     

电除尘器设计参数的选择

本文针对武钢采用的几台电除尘器的运行和试验，提出了电场风速粉尘驱进速度，线间距一极板间距之间存在一定的关系，通过试验找出它们的最佳值，对电除尘器设计中各参数的选取具有一定的参考和指导价值。 的     

脱硫用电石渣的重金属浸出特性及其对环境的影响

针对电厂用脱硫剂电石渣,分析了其基本组成及重金属浸出特性,为电厂脱硫设施的参数设计和环境影响评价提供依据和参考。研究结果表明,脱硫用电石渣主要成分为Ca（OH）2,含量在40%～50%之间;在8种重金属的含量中,只有Cd的含量超出土壤质量三级标准的要求,基本不会对土壤造成污染。浸出毒性试验表明,电石渣及其脱硫产物属于非危险废物,其各种重金属的浸出浓度主要受其本身重金属含量和最终pH的影响,这种影响在Pb、Cu和Cd上表现得较为突出,酸性环境下更有利于他们的浸出;碱性环境下有利于Pb和Ni的浸出。     

水环境监测结果的审核重点与审核方法

环境水质监测分析过程中水质指标多,监测数据多,数据的审核工作比较复杂。数据审核是水质分析工作质量保证的一个重要环节,是整个质量保证体系中有效的控制手段。主要从理论上分析环境监测中水质指标之间的关系,为水质监测人员监测和数据审核提供参考,从而提高数据质量,为环境水质管理服务。     

循环经济的环境安全作用探析

通过分析失业与贫困、贫困与环境安全的关系,揭示了环境恶化与贫困、失业等社会问题的交叉性.循环经济,通过延长产业链扩大就业,有利于建立长期有效的就业机制,增加就业的稳定性,从而实现对环境安全的有效作用.     

石化企业浮顶罐大呼吸损耗核算方法分析

石化企业储罐无组织排放挥发性有机物(VOCs)带来严重的环境问题和油品损耗问题,以浮顶罐的大呼吸损耗为代表。在概述浮顶罐大呼吸损耗机理的基础上,以北京某石化企业的甲苯内浮顶罐为基准案例,对国内外4种核算公式进行了对比分析,考察了影响浮顶罐大呼吸损耗的因素,并提出有效的减耗措施。结果表明:采用我国推荐的公式进行核算更符合我国实际,需建立和完善以我国有机液体理化参数和储罐构造为基准的核算方法和软件;影响浮顶罐大呼吸损耗的主要因素包括油品性质、周转量、罐体直径、罐壁黏附系数等,其中罐壁黏附系数为关键影响因素。     

电厂筒仓安全惰化保护装置的研制运用

贮煤筒仓的安全性能关系着电厂的安全运行,为解决筒仓可燃气体浓度增高而导致爆炸问题,可将惰性气体氮气通入筒仓内稀释和置换可燃气体。分析了电厂筒仓安全惰化保护系统的配置及运行情况,为电厂筒仓安全惰化保护装置设计和应用提供参考。     

生态安全视角下的循环经济研究

生态安全是人类可持续发展的基石,目前,生态安全问题已成为中国经济可持续发展的瓶颈。在深入分析经济社会系统与生态系统之间关系的基础上,认为生态安全问题凸显的根源在于经济社会系统对生态系统的过度干预,且经济社会系统运行生态化和资源利用高效化是缓解经济发展与生态安全之间矛盾的关键;从系统的高度,围绕生态化与高效化剖析循环经济的内涵,并从理论上分析"3R"原则及其经济实践与生态安全的关系,认为循环经济是经济社会系统在资源利用方面的系统变革,可有效推动经济发展与生态安全协同共进。     

加强化工环保工作准备实施ISO14000标准

介绍了国际标准化组织制订的环境管理系列标准－ＩＳＯ１４０００的内容，与ＩＳＯ９０００的关系，实施ＩＳＯ１４０００的准确工作与步骤，对化工企业实施该标准提出了建议。     

Mathematical modelling as a tool for environmental evaluation of industrial sectors in Colombia

A general mathematical model has been developed as a tool for environmental evaluation of industrial chemical processes. This model is based on the life cycle assessment (LCA) methodology and includes a modular and cumulative conceptual approximation. Accordingly, the model considers the potential effects on the environment caused by mass, energy and exergy flows. For environmental loads related with mass flows, two main categories are defined: pollution and perturbation environmental effects. Whereas for the environmental effect associated with energy flows, a factor defined as “energy dissipation” is employed, and similarly for exergy flows, a “exergy destruction” parameter is used. The measurement unit employed throughout the model is expressed in terms of “potential environmental impact units/hour”. As an example study case, the integrated production chain (IPC) for nitric acid production in the Colombian context is evaluated. This particular IPC includes the ammonia production plant, energy plants and main process plant. The results demonstrate that for environmental perturbation effects based on mass flows, the main contribution in the IPC corresponds to the energy plants. In the case of pollution environmental loads, the principal contribution relates to ammonia production. Regarding environmental effects associated with energy flows, the highest “energy dissipation” factor corresponds to the main process, followed in order by the ammonia process. Finally, for the effect denominated as “exergy destruction”, it could be established that Colombian energy plants show the highest contribution in the IPC.     

输变电工程电磁影响及其环境影响评价问题的探讨

结合各电压等级输变电工程环境影响评价的实际工作经验,以及国内工频电场和磁场污染投诉案例,介绍了国内外有关高压输变电工程产生的电磁环境与人类健康关系的研究进展.我国环境影响评价的相关标准已最大限度地考虑了电磁环境的影响,对民众健康不会产生副作用.同时,结合实际工作经验提出了加强和改进输变电环评工作的建议.     

Feedstock recycling of waste polymers by thermal cracking in molten metal: thermodynamic analysis

Waste plastics contribute to serious environmental and social problems, such as the loss of natural resources, environmental pollution, and depletion of landfill space, but they also create demands on the environmentally-oriented part of the society. Feedstock recycling of scrap polymers by thermal and chemical methods is well known and environmentally accepted. The paper presents the results of thermodynamic analysis of the conversion of polyolefins in a fuel-like mixture of hydrocarbons using thermal cracking in a new type of tubular reactor with molten metal. Evaluation of the efficiency of the process was based on exergy calculations. Calculated exergy efficiency was ca. 79.5 %. It means that feedstock recycling of waste is better from an energetic and environmental point of view than other processes, particularly incineration.     

Environmental assessment and accounting for the waste disposal stream in Bangkok,Thailand

It is very important that waste should be controlled and appropriately handled in a waste disposal stream, considering its impact on the environment. In this research, the LCA-EA model was applied to the current waste disposal stream of the BMR as well as other waste disposal stream scenarios, so that treatment cost, environmental load and environmental cost were assessed quantatively. The results of this study showed that in the current waste diposal stream in Bangkok, there were large contributions from carbon dioxide and methane to the greenhouse gas emissions from the stream. The study was able to quantify the reductions in environmental load associated with various waste disposal stream scenarios, using the baseline scenario as a standard.     

Safety management by use of laser mass spectrometry of polychlorinated biphenyls (PCBs) in the processed gas and work environment of a PCB disposal plant

This study demonstrates the applicability of laser mass spectrometry for safety management of the processed gas and the work environment in a polychlorinated biphenyl (PCB) disposal plant. By utilization of laser ionization/ion trapping storage/time-of-flight mass spectrometry (LI-IT-TOFMS), we analyzed gaseous PCBs from scrap capacitors with on-line detection. It was confirmed that few contaminants were detected in the spectrum. By the effect of laser-induced selective ionization, it was considered that there was little interference with the mass range of PCBs. The accuracy of LI-IT-TOFMS when analyzing environmental gas was almost the same as that for the PCB standard gas. It was possible to perform on-line analysis of the work environment for over 2000 h (120 000 data points). LI-IT-TOFMS was thus shown to be a very useful method for ensuring the safety of the work environment in disposal plants for PCBs.     

Legal Aspects of the Safety of the Techa Cascade of Reservoirs—Liquid Radioactive Waste Storage Facilities

In Russia in 1950–1960 solutions for the localization and storage of large volumes of liquid radioactive waste produced during defensive tasks were accomplished using natural and man-made water objects. At present, they are non-isolated from the environment and radioactive waste storage facilities constitute a serious potential menace. These objects are not allowed by the current legislation of the Russian Federation on environmental protection and safety. However, they do exist and there are no definite and approved engineering solutions regarding their removal. One of these objects is the Techa Cascade of Reservoirs (TCR) of the Mayak plant. In this article, TCR protection requirements are based on and formalized taking into account the legislation of the Russian Federation and the biospheric approach to the radiation protection of humans and the environment. Special safety requirements are needed because the standard argument “from human exposure to discharge standards” is invalid owing to the fact that the possibility of using water objects that have had contact with the TCR is restricted by law.     

Contribution of individual waste fractions to the environmental impacts from landfilling of municipal solid waste

A number of LCA-based studies have reported on the environmental performance of landfilling of mixed waste, but little is known about the relative contributions of individual waste fractions to the overall impact potentials estimated for the mixed waste. In this paper, an empirical model has been used to estimate the emissions to the environment from landfilling of individual waste fractions. By means of the LCA-model EASEWASTE, the emissions estimated have been used to quantify how much of the overall impact potential for each impact category is to be attributed to the individual waste fractions. Impact potentials are estimated for 1 tonne of mixed waste disposed off in a conventional landfill with bottom liner, leachate collection and treatment and gas collection and utilization for electricity generation. All the environmental aspects are accounted for 100 years after disposal and several impact categories have been considered, including standard categories, toxicity-related categories and groundwater contamination.Amongst the standard and toxicity-related categories, the highest potential impact is estimated for human toxicity via soil (HTs; 12 mPE/tonne). This is mostly caused by leaching of heavy metals from ashes (e.g. residues from roads cleaning and vacuum cleaning bags), batteries, paper and metals. On the other hand, substantial net environmental savings are estimated for the categories Global Warming (GW; ?31 mPE/tonne) and Eco-Toxicity in water chronic (ETwc; ?53 mPE/tonne). These savings are mostly determined by the waste fractions characterized by a high content of biogenic carbon (paper, organics, other combustible waste). These savings are due to emissions from energy generation avoided by landfill gas utilization, and by the storage of biogenic carbon in the landfill due to incomplete waste degradation.     

1000 MW燃煤机组电除尘深度节能技术研究及应用

电除尘设备在减少工业粉尘排放量、降低大气环境污染、保护生态环境等方面有着重要的作用,随着我国对节能减排工作的重视及环保要求的提高,保证其安全、稳定、经济、节能运行成为火电厂环保工作重点。对北仓电厂三期2×1000 MW机组电除尘电场供电方式优化、电除尘振打方式优化、电除尘闭环控制技术、电除尘高频电源技术、电除尘灰斗、瓷套蒸汽加热技术组合集成应用进行了研究,在确保除尘效率达到要求的情况下,降低运行电耗。相关的电除尘深度节能技术成果在国内同类型设备中具有一定的借鉴意义。     

变电站电磁环境管理现状概述

主要论述了当前我国变电站电磁环境管理方面的现状,包括政策法规、标准规范以及当前的电磁环境监测方法,并探讨了变电站电磁环境管理中存在的诸多问题与不足。在此基础上提出了电磁环境管理的相关措施和对策建议,包括完善法规、标准体系、加强监管体系建设、细化公众参与和加强电磁环境的科普宣传以及探索新的电磁环境监测方法。最后,重点介绍了变电站电磁环境在线监测管理的方法。     

Environmental assessment of sewage sludge as secondary raw material in cement production--a case study in China

A life cycle assessment was carried out to estimate the environmental impact of sewage sludge as secondary raw material in cement production. To confirm and add credibility to the study, uncertainty analysis was conducted. Results showed the impact generated from respiratory inorganics, terrestrial ecotoxicity, global warming, and non-renewable energy categories had an important contribution to overall environmental impact, due to energy, clinker, and limestone production stages. Also, uncertainty analysis results showed the technology of sewage sludge as secondary raw material in cement production had little or no effect on changing the overall environmental potential impact generated from general cement production. Accordingly, using the technology of sewage sludge as secondary raw material in cement production is a good choice for reducing the pressure on the environment from dramatically increased sludge disposal. In addition, increasing electricity recovery rate, choosing natural gas fired electricity generation technology, and optimizing the raw material consumption in clinker production are highly recommended to reduce the adverse effects on the environment.