粉尘云电火花点火研究

分析了粉尘云电火花点火研究的主要目的。对工业实际中常见的电火花点火源及其放电能量和现有实验装置中的火花触发电路与喷粉系统进行了研究,分析了实验过程中以电容能量和火花能量来衡量粉尘云电火花点火敏感性的主要误差。     

工业弯管泄爆口位置对爆炸湍流的影响分析

为研究弯管泄爆对气体爆炸的影响,基于试验测试和数值模拟(FLACs软件)分析管道泄爆状态下湍流的变化规律。结果表明：在试验条件下,封闭管道弯管内4.8 m处监测点湍流动能峰值为5 745.42 m²/s²,开口泄爆后该点湍流动能增幅为8.4%;当改变泄爆口位置时,弯道处监测点测得最大湍流动能相较于封闭管道该处最大湍流动能增幅为20.84%,弯管处湍流动能比直管最大增加了314%,影响因素主要为管道结构和泄爆口产生的排放和诱导作用;不同工况下内径0.125 m管道上泄爆口处最大湍流动能随着泄爆口位置和点火点之间的距离的增大而先增大后减小,二者的关系可拟合为一维高斯函数(Gauss Amp),拟合结果显示湍流动能最大为13 352.55m²/s²,此时泄爆口的孔口效应和流量限制都增大了湍流强度,导致更快的爆炸气流流出速度及更高的气体燃烧率,冲出气流携带的能量较大,对周围设施的危害影响最大。     

金属热颗粒引燃可燃堆积材料的实验研究

电焊操作、烟花燃放、工业磨削和高压电线碰撞等过程容易产生高温热颗粒。这些热颗粒一旦接触可燃材料就有可能引燃材料,导致火灾。该文对热颗粒引燃可燃堆积材料的行为进行实验研究,从而为工业堆积材料的火灾防控方法提供参考。实验加热一系列不同直径(6mm,8mm,10mm,12mm,15mm,20mm)的黄铜金属颗粒作为热源,并采用三种常见的工业堆积材料(木粉,炭粉,羟丙基甲基纤维素HPMC)作为可燃材料的代表物,研究不同功率金属热颗粒对材料的引燃行为,分析金属热颗粒引燃材料的临界功率。结果表明,材料本身的性质会影响热颗粒的引燃行为,HPMC的引燃时间最长,木粉的引燃时间最短。随着热颗粒直径的增加,热颗粒引燃三种材料所需的功率值整体呈增大的趋势。由于燃烧空腔的形成,HPMC的引燃临界功率相对较高。     

3D simulation of hydrogen ignition in a rapid compression machine

Low-temperature (at T < 900–950 K) ignition delays of hydrogen–air mixtures are mainly measured in rapid compression machines (RCM). This communication is aimed at numerical simulation of ignition delays of hydrogen–air mixtures in the RCM by means of a coupled three-dimensional (3D) Unsteady Reynolds-Averaged Navier–Stokes (URANS) – Particle Method (PM) simulation of RCM operation capable of catching turbulence–chemistry interaction. The study indicates that the time history of piston motion in an RCM affects the final state of a test mixture at the end of compression stroke and therefore influences the phenomena relevant to test mixture ignition. More specifically, the calculations show that different laws of piston motion at a fixed average piston velocity (i.e., fixed piston displacement and fixed compression time) and fixed compression ratio result in different evolution of mean pressure, temperature and velocity fields in the RCM test section leading to different ignition behavior. The reasons for the arising differences lie in the fact that the local instantaneous piston velocity determines the roll-up vortex structure, strength and turbulence dissipation in it, heat transfer in test-section walls, and mass leakage through piston rings.     

含水率及燃烧性能等级对中密度纤维板点燃行为及安全性能影响的研究

采用锥形量热仪,在不同辐射热流强度下,对三种燃烧性能等级(B级、C级和非阻燃)的中密度纤维板在不同相对湿度(0%、50%和98%)形成的含水率条件下进行了辐射引燃实验,测得点燃时间和热释放速率等参数。利用点燃理论中热厚型积分模型,推导了不同含水率不同燃烧性能等级(防火等级)纤维板的临界辐射热通量。通过对比发现,点燃时间随着板材含水率的增加而明显增大,而临界辐射热通量则几乎不受环境相对湿度(即含水率)的影响。添加阻燃剂可延长点燃时间,使板材临界辐射热通量增加,并能有效地降低纤维板材燃烧时的热释放速率。阻燃纤维板的临界辐射热通量要明显高于非阻燃纤维板,但是阻燃纤维板材之间相比,临界辐射热通量差别不大。因而,从本质安全的角度对材料的安全性进行评价,不能将临界辐射热通量作为单一的标准,必须综合多个参数进行全面评价。     

New approach to calculate the probability of ignition

The probabilistic approach to the evaluation of fire hazard and the effectiveness of fire-precaution measures enables a rational response to the randomness of fire outbreaks. This article employs the statistical analysis methods to elucidate the causes for the ignition of fire on a random sample of industrial buildings in the Republic of Slovenia. The analyses are based on the Structural Equation Modeling (SEM), which is a well established and important statistical analysis technique in the fields of social science, biology, psychology and medicine, but hitherto rarely applied in safety research. The results of the study demonstrate that for the analyzed random sample of industrial buildings the frequency of fire outbreaks statistically significantly depends only on the presence and the probability of exposure to the heat sources (flames, sparks, and hot surfaces), but does not significantly depend on the available quantity of flammable materials within the industrial structure.     

Towards an alternative criterion for the shipping safety of activated carbons: Part 4. The role of times to ignition

To the previously developed and implemented new criterion for the shipping safety of activated carbons is added a consideration of ignition times. It is shown that there is considerable support for the view that in the past shipments of such materials deemed on the basis of the IMCO/ISO test procedures to be subcritical have actually been supercritical, but that the long ignition times, exceeding voyage times, have prevented fire from developing.     

Comparative study on standardized ignition sources used for explosion testing

For the determination of safety characteristics of gases, vapors and dusts different types of ignition sources are used in international standards and guidelines. The paper presents test results of a comparative calorimetric and visual study between four different types of ignition sources. The ignition procedures were analyzed visually with a high-speed camera and electric recordings. In addition to that, the influence of the electrode-orientation, -distance as well as ignition energy on the reproducibility of the exploding wire igniter was tested.The exploding wire is already in use for standardized determination of safety characteristics of gases, first tests on the suitability of the exploding wire igniter for dust testing have been carried out but are not standardized yet. Using the exploding wire, the ignition energy can be varied from 2 J to 10 000 J (2 x 5000 J) and thus it could be used for gases, vapors, dusts and hybrid mixtures. Moreover it can be used at high initial pressures and it is the only ignition source with an easily measurable ignition energy release. Furthermore, it does not introduce another chemical reaction into the system.Finally, a proposal for a standard ignition source for explosion tests on hybrid mixtures is derived from the test results.     

膨胀型防火涂料对高压电力电缆引燃特性影响的实验研究

膨胀型防火涂料在电缆防火工程中有较广泛的应用,在使用过程中确保电缆涂料的效果与经济性具有重要意义。对喷涂不同厚度膨胀型高氯化聚乙烯防火涂料的高压电力电缆开展了在典型强度外加辐射热流条件的着火引燃实验,分析了电力电缆点燃时间、受热期间涂层对电缆外护套的保护与涂层受热后的形态变化。结果表明,电缆的着火行为与涂层厚度紧密相关。相比于未喷涂防火涂料的电缆,覆有膨胀型高氯化聚乙烯防火涂料的电缆在加热过程中明显膨胀,生成较软的泡沫状碳质层,且引燃时间较长,电缆起火后火势较弱。随着涂层厚度的增加,该涂料对电缆的阻燃和保护效果更为显著,研究结果表明,电缆表面喷涂1.0 mm厚度的防火涂料较为适宜。     

Effect of particle size and dust layer size on ignition characteristics of PMMA dust layer on hot surface

Deposition of combustible dust on a hot surface is a hidden danger of fire. In this work, polymethylmethacrylate (PMMA) dust was selected to analyse the influence of dust layer diameter, dust particle size and dust layer thickness on the ignition characteristics of PMMA dust layer. Critical heating temperatures and ignition time had been measured. The STA-GC/MS-FTIR analysis was used to determine that the main products of PMMA pyrolysis were MMA, CO, CO₂, and C₂H₄, of which CO and C₂H₄ were transported to the ambient to cause gas phase combustion on the surface of the dust layer. For 10 mm thick dust layer, the critical heating temperatures of 5 μm PMMA, 100 nm PMMA, and 30 μm PMMA were 300 °C, 330 °C, and 320 °C. As the thickness of the dust layer increased, the gas transport path became longer, the critical heating temperature and ignition time increased. The characteristic particle size (D [3,2]) was utilized to represent the true particle size, and the ignition time increased with the increase of the characteristic particle size. The increase in the diameter of the dust layer had a slight effect on the temperature history and ignition time of the dust layer.     

库房火灾事故中弹药热安全性研究*

为研究不同火灾条件下弹药发生慢速烤燃的升温速率,以典型地面仓库和舰船舱室火灾为研究对象,建立仿真模型,模拟计算发生火灾时弹药贮存环境的热激源强度及其演化规律,针对发动机在此类环境下的热安全性开展仿真计算,分析其响应规律。研究结果表明:不同火灾条件下弹药慢速烤燃的升温速率有很大区别且往往高于标准慢速烤燃试验常用的升温速率3.3 K/h。随着慢速烤燃升温速率的提高,发动机烤燃点火时间提前,点火时刻发动机中间位置温度下降,两端温度升高,且点火位置向发动机喉部移动。研究结果可以指导弹药库房的设计及弹药安全性增强设计。     

飞火和热辐射耦合作用点燃松针的实验研究

飞火颗粒点燃和火焰辐射引燃是森林-城镇交界域火灾两种主要引燃方式。已有很多研究关注单种引燃方式,但缺乏二者耦合作用下的引燃机理研究。实验研究了热颗粒与热辐射耦合作用下松针燃料床的点燃行为,分析了热颗粒尺寸、温度及辐射热通量对点燃特性的影响。实验结果表明:热颗粒和热辐射耦合作用的点燃危险性远远高于热颗粒或者热辐射单独作用下的点燃危险性。耦合作用时,点燃概率随颗粒尺寸、温度和辐射热通量增大而增大,热颗粒临界点燃温度以及临界辐射热通量均随热颗粒尺寸增大而降低;阴燃向明火转变的点燃时间随辐射热通量增大而降低,但与颗粒状态呈现出较为复杂的关系。