磁性纳米复合物对水中亚甲基蓝的吸附及其机理

利用正硅酸乙酯水解在磁性纳米锰锌铁氧体表面包裹SiO₂,制备了一种新型“核/壳”结构磁性纳米复合物材料Si-Fe-MNCs.采用N₂-吸附脱附法、透射电子显微镜(TEM)、振动样品磁强计(VSM)和傅利叶变换红外技术(FT-IR)分别对Si-Fe-MNCs的织构性能、形貌和磁性能进行了表征.结果表明,该磁性材料对亚甲基蓝表现出良好的吸附性能,318K时平衡吸附量在40.31~184.1mg/g之间,120min可达吸附平衡,符合准二级动力学方程.吸附过程符合Langmuir等温吸附模型,热力学计算结果表明Si-Fe-MNCs对亚甲基蓝的吸附是以表面物理吸附为主的自发吸热过程,红外结果表明氢键是Si-Fe-MNCs表面官能团与亚甲基蓝之间的主要作用力.Si-Fe-MNCs采用H₂O₂进行再生,5次循环使用后,对MB的平衡吸附量仍可维持在93.64mg/g.     

3,5-二硝基水杨酸表面修饰纳米Ti2吸附对硝基苯酚

化学吸附法合成3,5-二硝基水杨酸表面修饰的TiO₂纳米粒子,TiO₂表面修饰后呈浅黄色,TiO₂表面羟基与3,5-二硝基水杨酸发生类似于醇和酸间的酯化反应.表层链接有苯环,极性减弱,非极性增强,在水、苯、乙醇中均分散性良好,与芳香族污染物的亲合力增强,有利于吸附去除芳香族污染物.表面修饰的TiO₂纳米粒子20mg,在最佳吸附pH值3、吸附时间10min,对100mL对硝基苯酚(3～10 mg/L)的吸附率可由改性前的43%增至99.9%.该法吸附效率高,可直接达到一级排放标准,提供了深度处理对硝基苯酚废水的新方法.     

Enhanced adsorption of Methylene Blue from aqueous solution by chitosan-g-poly （acrylic acid）/vermiculite hydrogel composites

A series of chitosan-g-poly (acrylic acid)/vermiculite hydrogel composites were synthesized and used as adsorbents for the investigation of the e ect of process parameters such as vermiculite content, pH of dye solution, contact time, initial concentration of dye solution, temperature, ionic strength and concentration of surfactant sodium dodecyl sulfate on the removal of Methylene Blue (MB) from aqueous solution. The results showed that the adsorption capacity for dye increased with increasing pH, contact time and initial dye concentration, but decreased with increasing temperature, ionic strength and sodium dodecyl sulfate concentration in the present of the surfactant. The adsorption kinetics of MB onto the hydrogel composite followed pseudo second-order kinetics and the adsorption equilibrium data obeyed Langmuir isotherm. By introducing 10 wt.% vermiculite into chitosan-g-poly (acrylic acid) polymeric network, the obtaining hydrogel composite showed the highest adsorption capacity for MB, and then could be regarded as a potential adsorbent for cationic dye removal in a wastewater treatment process.     

柚子皮吸附水溶液中亚甲基蓝的机理研究

为研究柚子皮吸附水溶液中亚甲基蓝（MB）的吸附性能和吸附机理,试验考察了不同条件（如pH,生物材料粒径,染料浓度,吸附时间和温度等）对其吸附效果的影响. 结果显示:染料溶液在弱酸或碱性条件下有利于亚甲基蓝被该生物材料吸附;其粒径对吸附效果影响不大;在30 ℃的条件下,对亚甲基蓝的吸附在1 h左右达到平衡且符合二级动力学方程;在30 ℃及pH为8时的最大吸附量为169.49 mg/g,符合Langmuir方程;该吸附过程为放热反应,最大吸附量随温度的升高而减少. 表明柚子皮吸附亚甲基蓝的过程是以物理吸附为主,可作为染料废水处理材料.      

Mechanism of Methylene Blue adsorption on hybrid laponite-multi-walled carbon nanotube particles

The kinetics of adsorption and parameters of equilibrium adsorption of Methylene Blue(MB)on hybrid laponite-multi-walled carbon nanotube(NT)particles in aqueous suspensions were determined.The laponite platelets were used in order to facilitate disaggregation of NTs in aqueous suspensions and enhance the adsorption capacity of hybrid particles for MB.Experiments were performed at room temperature(298 K),and the laponite/NT ratio(X_l)was varied in the range of 0–0.5.For elucidation of the mechanism of MB adsorption on hybrid particles,the electrical conductivity of the system as well as the electrokinetic potential of laponite-NT hybrid particles were measured.Three different stages in the kinetics of adsorption of MB on the surface of NTs or hybrid laponite-NT particles were discovered to be a fast initial stage Ⅰ(adsorption time t=0–10 min),a slower intermediate stage Ⅱ(up to t=120 min)and a long-lasting final stage Ⅲ(up to t=24 hr).The presence of these stages was explained accounting for different types of interactions between MB and adsorbent particles,as well as for the changes in the structure of aggregates of NT particles and the long-range processes of restructuring of laponite platelets on the surface of NTs.The analysis of experimental data on specific surface area versus the value of X_l evidenced in favor of the model with linear contacts between rigid laponite platelets and NTs.It was also concluded that electrostatic interactions control the first stage of adsorption at low MB concentrations.     

磁性微球负载光催化剂的吸附特性研究

在TiO2/SiO2/Fe3O4物化特性的研究中,通过测定方法的改进首次获得光照反应阶段TiO2/SiO2/Fe3O4吸附量与溶液残余量间的定量关系(以苯酚为例,结果表明:在光照及无光照条件下TiO2/SiO2/Fe3O4遵循不同的吸附规律,以后者取代前者存在明显缺陷;揭示了凝聚现象是导致TiO2/SiO2/Fe3O4光活性降低的主要原因。     

改性石墨烯对水中亚甲基蓝的吸附性能研究

对十六烷基三甲基溴化铵(CTAB)改性石墨烯用于水中亚甲基蓝(MB)的去除进行了研究.用扫描电子显微镜(SEM)、透射电子显微镜(TEM)、X射线衍射分析仪(XRD)、傅里叶红外光谱分析仪(FTIR)和热重分析仪(TGA)对石墨烯和改性石墨烯性能进行表征.探讨了反应时间、pH、温度、剂量对石墨烯和改性石墨烯去除MB的影响.结果表明,在石墨烯制备过程中添加CTAB可以明显增大比表面积,提高MB的去除率.反应过程在前15 min内反应速率很快,并约在120 min内达到吸附平衡.吸附动力学符合伪二级动力学模型.最佳反应温度为293 K,吸附剂投加量的最适浓度为2 g·L-1,且吸附量的大小与溶液的初始pH值无关.通过Langmuir等温吸附方程得到改性石墨烯的最大吸附量86.43 mg·g-1,且为放热反应.     

铁改性赤泥吸附剂的制备及其除砷性能研究

以氧化铝生产废渣--赤泥为原料,采用铁盐改性处理制备了新型羟基铁包覆型赤泥除砷吸附剂.研究考察了吸附剂吸附砷效能、投加量、吸附时间和pH值对吸附除砷效果的影响;采用扫描电镜(SEM)、红外光谱(IR)、比表面积(BET)等仪器对吸附剂进行了表征,并探讨了吸附机制.结果表明,铁盐改性赤泥吸附剂对As(V)具有显著吸附效能,在pH为7,初始砷浓度为1 mg·L-1,铁盐改性赤泥吸附剂饱和吸附容量为50.6mg·g-1时,除砷率高达99.9%,吸附后出水砷含量可达到0.01 mg·L-1以下,吸附规律符合Langmuir等温方程式;溶液pH值显著影响砷去除效果,吸附机制主要为羟基铁的表面吸附机制;吸附后的吸附剂可通过NaOH溶液再生,脱附率达到92.1%.     

污泥液化生物炭对亚甲基蓝的吸附特性及机理

探讨污泥在乙醇-水混合溶剂中液化产生的生物炭的吸附潜力及其吸附机理（以亚甲基蓝（MB）废水为处理对象）,结果表明：生物炭的吸附容量随着MB溶液起始pH值升高而升高,当pH超过8时,MB的碱性褪色开始显现.吸附温度的上升（30~60℃）对生物炭吸附容量的影响不明显.吸附容量总体上随着吸附时间的增加而上升（240min前）,在240min后趋于稳定.吸附剂用量及初始MB浓度过高或过低都不利于生物炭的吸附,存在一个的临界点,分别是6mg和120mg/L.生物炭吸附MB的过程吻合准二级动力学方程（R²=0.9994）和Langmuir方程（R²=0.9831）,且为自发吸热的过程,受物理吸附和化学吸附联合控制,具体的机理包括：离子交换、官能团络合、π-π吸附等.     

改性秸秆材料对高盐废水中染料和重金属的吸附性能研究

高盐印染废水是一种难处理的工业废水,其盐度高、色度高,含有染料、重金属等多种污染物.本文针对高盐印染废水中污染物的特点,设计了一种制备过程简单、成本经济的柠檬酸/丙烯酰胺改性秸秆材料(WA-CA-AM),并通过SEM、FI-IR和DTG等表征手段分别观测材料形貌、测定表面官能团和热稳定性.同时在不同盐度下,考察了单元/多元污染物体系中WS-CA-AM对4种污染物亚甲基蓝(MB)、甲基橙(MO)、铜离子(Cu~(2+))和铬离子(Cr~(6+))的吸附效果.结果表明:在单元污染物体系中,WS-CA-AM对污染物的吸附量随盐度的升高而降低;在多元污染物体系中同时存在竞争吸附和协同吸附;通过二元体系得出4种污染物的吸附受盐度影响大小顺序为MOCu~(2+)Cr~(6+)MB.在高盐度下,四元混合体系中MB和Cu~(2+)的吸附量均比染料/重金属二元混合体系的要大,Cr~(6+)的吸附量虽受到一些抑制但依然可观,表明改性秸秆材料在高盐印染废水的处理中具有巨大的应用潜力.     

硅藻土负载纳米铁对Cd2+的吸附性能与机制研究

为了提高硅藻土(CDt)的吸附能力,采用NaBH_4液相还原二价铁法合成负载纳米铁的硅藻土颗粒(nZVI-CDt),运用扫描电镜(SEM)、傅里叶红外光谱(FTIR)、X射线衍射(XRD)和X射线光电子能谱(XPS)对nZVI-CDt进行表征,采用静态吸附法研究不同吸附条件对CDt和nZVI-CDt吸附Cd~(2+)的影响,并结合等温吸附属性、吸附过程控制步骤以及吸附动力学、热力学属性分析探讨了CDt和nZVI-CDt对Cd~(2+)的吸附机制.结果表明,负载纳米铁后,硅藻土的团聚现象得到改善,分散性更好,表面活性基团向有利于吸附方向发生变化,吸附能力得到显著提升,相对于CDt,nZVI-CDt对Cd~(2+)的吸附量提升了3.9倍;nZVI-CDt对Cd~(2+)的吸附较为迅速,20 min左右就可达到吸附平衡;随着投加量的增加,nZVI-CDt对Cd~(2+)的吸附量呈下降趋势,而初始浓度对Cd~(2+)的吸附影响则正好相反;相对于CDt,溶液初始pH值对nZVI-CDt吸附Cd~(2+)的影响明显减弱;nZVI-CDt对Cd~(2+)的吸附能力受温度影响不大;nZVI-CDt对Cd~(2+)的吸附符合Temkin等温吸附模型和拟二级动力学模型.吸附反应容易进行,且以物理吸附为主,吸附过程控制步骤为发生在微孔内的吸附反应.吸附热力学参数表明CDt和nZVI-CDt对Cd~(2+)的吸附是自发的吸热过程,且系统的无序性增加.     

Evaluation of the adsorption potential of titanium dioxide nanoparticles for arsenic removal

The adsorption potential of titanium dioxide (TiO2) nanoparticles for removing arsenic from drinking water was evaluated. Pure and iron-doped TiO2 particles are synthesized via sol-gel method. The synthesized TiO2 nanoparticles were then immobilized on ordinary sand for adsorption studies. Adsorption isotherms were conducted on the synthesized nanoparticles as well as the sand coated with TiO2 nanoparticles under varying conditions of air and light, namely, the air-sunlight (A-SL), air-light (AL), air-dark (AD) and nitrogen-dark (ND). X-Ray diffraction (XRD) analysis showed that the pure and the iron-doped TiO2 nanoparticles were in 100% anatase crystalline phase with crystal sizes of 108 and 65 nm, respectively.Adsorption of arsenic on the three adsorbents was non-linear that could be described by the Freundlich and Langmuir adsorption models. Iron doping enhanced the adsorption capacity of TiO2 nanoparticle by arresting its grain growth and making it visible light responsive resulting in a higher affinity for arsenic. Similarly, the arsenic removal by adsorption on the sand coated with TiO2 nanoparticles was the highest among the three types of sand used. In all cases, As(V) adsorbed more compared with As(III). Solution pH appeared to be the most important factor in controlling the amount of arsenic adsorbed.     

TiO2@酵母微球吸附废水中的荧光增白剂-VBL及再生研究

采用静电自组装的方法制备出具有草莓结构的TiO2@酵母微球作为吸附材料,对阴离子型荧光增白剂-VBL(FWA-VBL)废水进行吸附研究,考察了溶液pH、溶液初始浓度和TiO2@酵母投加量对吸附效果的影响.结果表明,酸性条件有利于TiO2@酵母微球对FWA-VBL的吸附,平衡吸附量随着溶液初始浓度的增加而增加,随着TiO2@酵母微球投加量的增加而减小.TiO2@酵母对FWA-VBL的吸附行为更加符合Langmuir等温模型,在温度为323.15K下最大吸附量为167.50mg/g; 吸附动力学符合二级动力学方程; 热力学参数表明吸附过程是自发的吸热过程.归因于光催化-吸附耦合效应,TiO2@酵母微球展现出了良好的原位再生能力.H2O2的添加有助于提高TiO2@酵母微球的再生性能.     

功能化多孔材料对CO_2的吸附分离研究进展

功能化多孔材料拥有优越的CO_2吸附和存储性能,在燃煤电厂、玻璃炉窑、水泥厂、钢铁厂等高耗能工矿企业采用CO_2吸附技术,对CO_2减排、减缓温室效应具有重要意义。随着研究的不断深入,新型CO_2吸附材料呈现出廉价、易获取、高吸附率等趋势,当前研究重点集中在介孔硅、金属有机框架、沸石、活性炭、聚合物等的表面功能化。总结了上述典型吸附剂功能化的最新成果,重点介绍多孔吸附材料的功能化方法、吸附机理与吸附动力学的研究进展,并提出多孔材料对CO_2的吸附分离的研究空间和发展趋势。     

改性活性炭对水溶液中双酚-A的吸附研究

采用HNO3、NaOH及高温N2对商用炭WV A1100进行表面改性处理,并利用BET、XPS、pH.及Boehm方法对活性炭进行物化表征.结果表明,HNO3改性明显降低了W20的比表面积,增加了其表面酸性含氧官能团数量,使等电点(pHpae)由4.95降至1.50;高温N2和NaOH改性处理后炭表面化学性质变化与HNO3氧化基本相反,pHp.升至近中性,其中高温N2处理降低了43.81%的表面积.另外,活性炭对双酚-A(BPA)的吸附实验结果表明,吸附体系中溶解氧的存在不会促使BPA在W20表面发生酚氧自由基氧化耦合,并且原炭W20、高温N2和NaOH改性处理后炭对BPA的吸附等温线结果满足Langmiur模型,而HNO3改性炭的吸附行为更符合Freundlich模型,其中高温N2改性炭表现出最好的吸附BPA能力,饱和吸附量值达到了526.32mg/g,是能力最差炭(HNO3改性)的3倍,结合表征结果分析得出,在吸附体系中炭表面的憎水性和静电荷密度,是控制分子态BPA吸附过程的主要因素,即吸附主要遵循π-π理论.     

稀土铒掺杂TiO_2光催化剂的吸附和光催化活性研究

通过溶胶-凝胶法成功的制备了一系列Er3+掺杂的TiO2光催化剂,并通过XRD、DRS对催化剂进行了表征,结果表明所制催化剂为锐钛矿型,Er3+的掺杂有利于抑制晶粒生长,提高晶体的热稳定性。紫外-可见吸收(DRS)光谱证实,Er3+的掺杂增强了催化剂在可见光区域的吸收能力。吸附实验结果表明,Er3+的掺杂显著提高了橙黄I在TiO2催化剂表面的吸附能力,随掺杂量增加,吸附增强。活性实验结果表明,Er3+的掺杂显著提高了TiO2的光催化活性,最佳掺杂量为1.5%。     

Removal of Cd2+ from water by Friedel’s salt (FS: 3CaO.Al2O3·CaCl2·10H2O): Sorption characteristics and mechanisms

The development of low-cost and efficient new mineral adsorbents has been a hot topic in recent years. In this study, Friedel’s salt (FS:3CaO·A12O3 ·CaCl2 ·10H2O), a hexagonal layered inorganic absorbent, was synthesized to remove Cd2+ from water. The adsorption process was simulated by Langmuir and Freundlich models. The adsorption mechanism was further analyzed with TEM, XRD, FT-IR analysis and monitoring of metal cations released and solution pH variation. The results indicated the adsorbent FS had an outstanding ability for Cd(Ⅱ) adsorption. The maximum adsorption capacity of the FS for Cd(Ⅱ) removal can reach up to 671.14 mg/g. The nearly equal numbers of Cd2+ adsorbed and Ca2+ released demonstrated that ion-exchange (both surface and inner) of the FS for Cd(Ⅱ) played an important role during the adsorption process. Furthermore, the surface of the FS after adsorption was microscopically disintegrated while the inner lamellar structure was almost unchanged. The behavior of Cd(Ⅱ) adsorption by FS was significantly affected by surface reactions. The mechanisms of Cd2+ adsorption by the FS mainly included surface complexation and surface precipitation. In the present study, the adsorption process was fitted better by the Langmuir isotherm model (R2 = 0.9999) than the Freundlich isotherm model (R2 = 0.8122). Finally, due to the high capacity for ion-exchange on the FS surface, FS is a promising layered inorganic adsorbent for the removal of Cd(Ⅱ) from water.     

TiO_2/海泡石催化剂的制备及其对印染废水的处理

分别用焦硫酸钾和钛酸丁酯制得TiO2酸性溶胶,再用浸渍、振荡等方法制得TiO2/海泡石光催化剂。研究了所制得的光催化剂对模拟活性艳兰印染废水的吸附和光催化性能:光催化剂对活性艳兰的吸附能力较原矿粉大大提高;在光催化体系中,活性艳兰的高去除率(>96%)并不是简单的吸附行为,而是发生了光催化降解被完全矿化而去除,说明Ti已经嵌入到海泡石的层间结构中。在反应液中加入H2O能提升光催化降解的速率,同时光催化过程会使溶液pH值朝着中性方向变化。     

Reaction site and mechanism in the UV or visible light induced TiO2 photodegradation of Orange G

For TiO2 heterogeneous reaction, the reaction site and the detailed mechanism are interesting and controversy topics. In this paper, effects of surface fluorination of TiO2 on the photocatalytic degradation of an azo dye, Orange G（OG） under UV or visible light irradiation were investigated, and the possible reaction site and mechanism were elucidated. The adsorption of OG on TiO2 was nearly inhibited by fluoride but its UV light induced photodegradation rate was greatly increased by a factor of about 2.7, which was due to the more generated free hydroxyl radicals. It supported the views that fluoride could desorb the oxidant species from surface and that the reaction sites could move to the bulk solution. In TiO2/Vis system, the observed inhibition effects of fluorination could be interpreted by the competitive adsorption, which provided additional evidences that the visible light sensitized photodegradation of dye pollutants on the catalyst surface.