Concept and application of anaerobic suspended granular sludge bed （SGSB） reactor for wastewater treatment

Bed expansion serves an important function in the design and operation of an upflow anaerobic reactor. An analysis of the flow pattern of expanded granular sludge bed （EGSB） reactors shows that most EGSB reactors do not behave as expanded bed reactors, as is widely perceived. Rather, these reactors behave as fluidized bed reactors based on the classic chemical reactor theory. In this paper, four bed expansion modes, divided as static bed, expanded bed, suspended bed, and fluidized bed, for bioreactors are proposed. A high-rate anaerobic suspended granular sludge bed （SGSB） reactor was then developed. The SGSB reactor is an upflow anaerobic reactor, and its expansion degree can be easily controlled within a range to maintain the suspended status of the sludge bed by controlling upfiow velocity. The results of the full-scale reactor confirmed that the use of SGSB reactors is advantageous. The full-scale SGSB reactor runs stably and achieves high COD removal efficiency （about 90%） at high loading rates （average 40 kg-COD·m^-3·d^-1, maximum to 52 kg·COD·m^-3 ·d^-1） based on the SGSB theory, and its expansion degree is between 22% and 37%.     

Achievement of high rate nitritation with aerobic granular sludge reactors enhanced by sludge recirculation events

A ratio control strategy has been used to demonstrate the feasibility of this automatic control procedure for the achievement of stable full and partial nitritation. The control strategy assured constant ratio between the dissolved oxygen (DO) and the total ammonia nitrogen (TAN) concentrations in the bulk liquid of aerobic granular sludge reactors operating in continuous mode. Three different set-ups with different reactor capacities were used (3, 110, and 150 L). High strength synthetic wastewaters and reject water were tested with similar performance. Achieved nitrogen loading rates ranged between 0.4 and 6.1 kgN·m^-3·d^-1, at temperatures between 20°C and 30°C. Granular sludge and nitritation were stable in the long term continuous operation of the reactors. Suitable stable effluent for Anammox has been obtained using the desired TAN setpoint (i.e. 50% of influent ammonium oxidation). An existing biofilm model developed incorporating the implemented control loops and validated in a previous publication was used to investigate the effects of the ammonium concentration of the influent and the biofilm density on the achievement of full nitritation. The model demonstrated how sludge recirculation events led to a stable and significant increase of the biomass concentration in the reactor, which in turn resulted in the achievement of high nitrogen loading rates, due to the action of the control strategy. The model predicted an enhancement of stable full nitritation at higher ammonium concentrations in the influent. Poor influence of the biofilm density in the achievement of full nitritation was predicted with the model.     

添加剂对污泥厌氧消化性能的影响

在间歇培养条件下,研究了还原型辅酶Ⅱ（NADPH）、乙酰辅酶A（Acetyl Co A）和对氨基苯甲酸（PABA）3种添加剂对污泥厌氧消化性能的影响.结果表明,3种微生物活性促进剂均能促进污泥厌氧消化产气.其中,NADPH的促进效果最为显著,消化第35 d,产甲烷量比对照组高15.90%.在污泥含固率为3%、未调初始pH（pH=6.7）和温度35℃的厌氧消化条件下,NADPH的最佳添加量为50 mg.L-1,消化第36 d,污泥累积产甲烷量127.13 mL.g-1VSS.在含固率3%、初始pH=8.5、温度55℃和NADPH添加量为50 mg.L-1的工艺条件下,污泥厌氧产气效果最佳,消化第30 d时累积产甲烷量达158.02 mL.g-1VSS.     

污泥超声破解效应及厌氧消化性能研究

针对超声破解污泥的可行性进行了实验研究,重点考察了超声频率、比能耗、作用时间等因素对破解效应的影响,探讨了破解污泥的厌氧消化性能。结果表明,超声作用的施加可使污泥固体有效破解,污泥细胞内的活性有机物被释放至水相并形成溶解性有机物,表现为SCODCr的显著增加;采用低频、高比能耗及延长作用时间有利于获取高的SCODCr增加值;污泥在频率25kHz、比能耗2.0W/mL、作用时间30min条件下破解,其厌氧消化累计产气量可从破解前的268mL提高到473mL,相应TCODCr去除率、VS去除率分别从39.1%、33.5%提高至54.3%、61.7%。研究结果表明采用超声破解技术提高污泥的厌氧消化性是可行的。     

High-solid anaerobic digestion of sewage sludge: achievements and perspectives

• High-solid anaerobic digestion (HS-AD) of sewage sludge (SS) is overviewed. • Factors affecting process stability and performance in HS-AD of SS are revealed. • HS effect and knowledge gaps of current research on the HS-AD of SS are identified. • Future efforts on addressing knowledge gaps and improving HS-AD of SS are proposed. High-solid anaerobic digestion (HS-AD) has been applied extensively during the last few decades for treating various organic wastes, such as agricultural wastes, organic fractions of municipal solid wastes, and kitchen wastes. However, the application of HS-AD to the processing of sewage sludge (SS) remains limited, which is largely attributable to its poor process stability and performance. Extensive research has been conducted to attempt to surmount these limitations. In this review, the main factors affecting process stability and performance in the HS-AD of SS are comprehensively reviewed, and the improved methods in current use, such as HS sludge pre-treatment and anaerobic co-digestion with other organic wastes, are summarised. Besides, this paper also discusses the characteristics of substance transformation in the HS-AD of SS with and without thermal pre-treatment. Research has shown that the HS effect is due to the presence of high concentrations of substances that may inhibit the function of anaerobic microorganisms, and that it also results in poor mass transfer, a low diffusion coefficient, and high viscosity. Finally, knowledge gaps in the current research on HS-AD of SS are identified. Based on these, it proposes that future efforts should be devoted to standardising the definition of HS sludge, revealing the law of migration and transformation of pollutants, describing the metabolic pathways by which specific substances are degraded, and establishing accurate mathematical models. Moreover, developing green sludge dewatering agents, obtaining high value-added products, and revealing effects of the above two on HS-AD of SS can also be considered in future.     

Methods to alleviate the inhibition of sludge anaerobic digestion by emerging contaminants: a review

The rising occurrence of emerging contaminants in sludges both inhibits the anaerobic digestion of sludges and induces health issues when sludges are recycled in agriculture, calling for methods to remove contaminants. Here we review emerging pollutants in wastewater treatment plants, before and after anaerobic digestion. We present their inhibitory effects and remediation methods to alleviate inhibition. Pharmaceuticals have been detected in about 50% of the sludge samples. Sewage sludge contaminants include 19% of diuretics, 16–21% of lipid-modifying agents, hydrochlorothiazide, diclofenac, furosemide, clarithromycin, atorvastatin, and carbamazepine. Levels of antibiotics, azithromycin, ciprofloxacin, and estrone range from 500 to 600 ng/g in sludges from wastewater treatment plants. Remediation methods comprise electrooxidation, ultrasonication, thermal hydrolysis, ozonation, and bioaugmentation. Fermenting the sludges with acidogenic bacteria reduces the level of emerging pollutants in the supernatant. Nonetheless, liquid digestates still contains emerging pollutants such as sunscreen octocrylene at 147 ug/L and acetaminophen at 58.6 ug/L. As a result, pretreatment of sludge containing emerging pollutants is required.

     

Structure and formation of anoxic granular sludge—A string-bag hypothesis

Anoxic granular sludge was developed in a laboratory-scale sequencing batch reactor which was fed with sodium acetate and sodium nitrate as electron donor and accepter. The sludge in the reactor was almost granulated after approximately 90 days of cultivation. In the present study, a detailed examination of surface morphology and internal structure of anoxic granular sludge was conducted using scanning electron microscope. It showed that the bacteria inside the granules had a uniform, coccus-like shape. By contrast, filamentous bacteria were predominant outside the granules. These bacteria were woven and had wrapped the coccus bacteria together to form granules. The small amounts of DO in the liquid bulk promoted the growth of filamentous bacteria on the surface of the granules. A string-bag hypothesis was proposed to elucidate the structure and formation of the anoxic granular sludge. It suggested that micro-aeration could be a method to promote granulation in practical anoxic treatment systems.     

Cultivation of aerobic granular sludge in a conventional,continuous flow,completely mixed activated sludge system

Aerobic granules were formed in a conventional, continuous flow, completely mixed activated sludge system (CMAS). The reactor was inoculated with seed sludge containing few filaments and fed with synthetic municipal wastewater. The settling time of the sludge and the average dissolved oxygen (DO) of the reactor were 2 h and 4.2 mg·L^-1, respectively. The reactor was agitated by a stirrer, with a speed of 250 r·min^-1, to ensure good mixing．The granular sludge had good settleability, and the sludge volume index (SVI) was between 50 and 90 mL·g^-1. The laser particle analyzer showed the diameter of the granules to be between 0.18 and 1.25 mm. A scanning electron microscope (SEM) investigation revealed the predominance of sphere-like and rod-like bacteria, and only few filaments grew in the granules. The microbial community structure of the granules was also analyzed by polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE). Sequencing analysis indicated the dominant species were α, β, and γ-Proteobacteria, Bacteroidetes, and Firmicutes. The data from the study suggested that aerobic granules could form, if provided with sufficient number of filaments and high shear force. It was also observed that a high height-to-diameter ratio of the reactor and short settling time were not essential for the formation of aerobic granular sludge.     

Effect of illumination on the hydrogen-production capability of anaerobic activated sludge

To investigate the influence of illumination on the fermentative hydrogen production system, the hydrogen production efficiencies of two kinds of anaerobic activated sludge (floc and granule) from an anaerobic baffled reactor were detected under visible light, dark and light-dark, respectively. The 10 mL floc sludge or granular sludge was respectively inoculated to 100 mL diluted molasses (chemical oxygen demand of 8000 mg·L^-1) in a 250 mL serum bottle, and cultured for 24 h at 37°C under different illumination conditions. The results showed that the floc was more sensitive to illumination than the granule. A hydrogen yield of 19.8 mL was obtained in the dark with a specific hydrogen production rate of 3.52 mol·kg^-1MLVSS·d^-1 (floc), which was the highest among the three illumination conditions. Under dark condition, the hydrogen yield of floc sludge reached the highest with the specific hydrogen production rate of 3.52 mol·kg^-1MLVSS·d^-1, and under light-dark, light, the specific hydrogen production rate was 3.11 and 2.21 mol·kg^-1MLVSS·d^-1, respectively. The results demonstrated that the illumination may affect the dehydrogenase activity of sludge as well as the activity of hydrogen-producing acetogens and then impact hydrogen production capacity.     

Roles of acid-producing bacteria in anaerobic digestion of waste activated sludge

Three acid-producing strains, AFB-1, AFB-2 and AFB-3, were isolated during this study, and their roles in anaerobic digestion of waste activated sludge (WAS) were evaluated. Data of 16S rRNA method showed that AFB-1 and AFB-2 were Bacillus coagulans, and AFB-3 was Escherichia coli. The removal in terms of volatile solids (VS) and total chemical oxygen demand (TCOD) was maximized at 42.7% and 44.7% by inoculating Bacillus coagulans AFB-1. Besides, the optimal inoculum concentration of Bacillus coagulans AFB-1 was 30% (v/v). Solubilization degree experiments indicated that solubilization ratios (SR) of WAS reached 20.8%±2.2%, 17.7%±1.48%, and 11.1%±1.53%. Volatile fatty acids (VFAs) concentrations and compositions were also explored with a gas chromatograph. The results showed that VFAs improved by 98.5%, 53.0% and 11.6% than those of the control, respectively. Biochemical methane potential (BMP) experiments revealed that biogas production increased by 90.7% and 75.3% when inoculating with Bacillus coagulans AFB-1 and AFB-2. These results confirmed that the isolated acid-producing bacteria, especially Bacillus coagulans, was a good candidate for anaerobic digestion of WAS.

Open image in new window

     

Biosorption of Direct Yellow 12 from aqueous solution using green alga Ulva lactuca

The potential of commonly available green alga Ulva lactuca was investigated as viable biomaterials for removal of synthetic azo dye (Direct Yellow 12, DY-12) from aqueous solution. The results obtained from the batch experiments revealed that the ability of the U. lactuca to remove DY-12 from its aqueous solution was dependent on the dye concentration, pH, and algal biomass but less dependent on the particle size of the U. lactuca. The equilibrium conditions and kinetics of adsorption were investigated, and the adsorption kinetic was consistent with the pseudo-second-order model (R ²=1). The adsorption isotherm followed only the Freundlich model with a correlation coefficient R ²=0.99. This study demonstrated that the U. lactuca could be used as an effective biosorbent for the removal of DY-12 from its aqueous solution.     

Biosorption of Cr(III) from aqueous solution by freeze-dried activated sludge: Equilibrium,kinetic and thermodynamic studies

Batch biosorption experiments were conducted to remove Cr(III) from aqueous solutions using activated sludge from a sewage treatment plant. An investigation was conducted on the effects of the initial pH, contact time, temperature, and initial Cr(III) concentration in the biosorption process. The results revealed that the activated sludge exhibited the highest Cr(III) uptake capacity (120 mg·g⁻¹) at 45°C, initial pH of 4, and initial Cr(III) concentration of 100 mg·L⁻¹. The biosorption results obtained at various temperatures showed that the biosorption pattern accurately followed the Langmuir model. The calculated thermodynamic parameters, ΔG^o (−0.8– −4.58 kJ·mol⁻¹), ΔH^o (15.6–44.4 kJ·mol⁻¹), and ΔS^o (0.06–0.15 kJ·mol⁻¹·K⁻¹) clearly indicated that the biosorption process was feasible, spontaneous, endothermic, and physical. The pseudo first-order and second-order kinetic models were adopted to describe the experimental data, which revealed that the Cr(III) biosorption process conformed to the second-order rate expression and the biosorption rate constants decreased with increasing Cr(III) concentration. The analysis of the values of biosorption activation energy (E_a = −7 kJ·mol⁻¹) and the intra-particle diffusion model demonstrated that Cr(III) biosorption was film-diffusion-controlled.     

Biosorption of Direct Yellow 12 from aqueous solution using green alga Ulva lactuca

The potential of commonly available green alga Ulva lactuca was investigated as viable biomaterials for removal of synthetic azo dye (Direct Yellow 12, DY-12) from aqueous solution. The results obtained from the batch experiments revealed that the ability of the U. lactuca to remove DY-12 from its aqueous solution was dependent on the dye concentration, pH, and algal biomass but less dependent on the particle size of the U. lactuca. The equilibrium conditions and kinetics of adsorption were investigated, and the adsorption kinetic was consistent with the pseudo-second-order model (R²=1). The adsorption isotherm followed only the Freundlich model with a correlation coefficient R²=0.99. This study demonstrated that the U. lactuca could be used as an effective biosorbent for the removal of DY-12 from its aqueous solution.     

Use of gamma-irradiation pretreatment for enhancement of anaerobic digestibility of sewage sludge

The effects of γ-irradiation pretreatment on anaerobic digestibility of sewage sludge was investigated in this paper. Parameters like solid components, soluble components, and biogas production of anaerobic digestion experiment for sewage sludge were measured. The values of these parameters were compared before and after γ-irradiation pretreatment. Total solid (TS), volatile solid (VS), suspended solid (SS), volatile suspended solid (VSS), and average floc size of samples decreased after γ-irradiation treatment. Besides, floc size distribution of sewage sludge shifted from 80–100 μm to 0–40 μm after γ-irradiation treatment at the doses from 0 to 30 kGy, which indicated the disintegration of sewage sludge. Moreover, microbe cells of sewage sludge were ruptured by γ-irradiation treatment, which resulted in the release of cytoplasm and increase of soluble chemical oxygen demand (SCOD). Both sludge disintegration and microbe cells rupture enhanced the subsequent anaerobic digestion process, which was demonstrated by the increase of accumulated biogas production. Compared with digesters fed with none irradiated sludge, the accumulated biogas production increased 44, 98, and 178 mL for digesters fed sludge irradiated at 2.48, 6.51, and 11.24 kGy, respectively. The results indicated that γ-irradiation pretreatment could effectively enhance anaerobic digestibility of sewage sludge, and correspondingly, could accelerate hydrolysis process, shorten sludge retention time of sludge anaerobic digestion process.     

Feasibility assessment of up-flow anaerobic sludge blanket treatment of sulfamethoxazole pharmaceutical wastewater

The UASB system successfully treated sulfamethoxazole pharmaceutical wastewater. High concentration sulfate of this wastewater was the main refractory factor. UASB recovery performance after a few days of inflow arrest was studied. The optimal UASB operating conditions for practical application were determined. Treatment of sulfamethoxazole pharmaceutical wastewater is a big challenge. In this study, a series of anaerobic evaluation tests on pharmaceutical wastewater from different operating units was conducted to evaluate the feasibility of using anaerobic digestion, and the results indicated that the key refractory factor for anaerobic treatment of this wastewater was the high sulfate concentration. A laboratory-scale up-flow anaerobic sludge blanket (UASB) reactor was operated for 195 days to investigate the effects of the influent chemical oxygen demand (COD), organic loading rate (OLR), and COD/SO₄^2? ratio on the biodegradation of sulfamethoxazole in pharmaceutical wastewater and the process performance. The electron flow indicated that methanogenesis was still the dominant reaction although sulfidogenesis was enhanced with a stepwise decrease in the influent COD/SO₄^2? ratio. For the treated sulfamethoxazole pharmaceutical wastewater, a COD of 4983 mg/L (diluted by 50%), OLR of 2.5 kg COD/(m³·d), and COD/SO₄^2? ratio of more than 5 were suitable for practical applications. The recovery performance indicated that the system could resume operation quickly even if production was halted for a few days.     

剩余污泥厌氧发酵过程中氮的转化规律与计量关系

以某采用A/O生物处理工艺水质净化厂排出的剩余污泥为研究对象,利用18组棕色消化瓶,定期测试污泥中TCOD(总化学需氧量)、SCOD(溶解性化学需氧量)、TSS(总悬浮固体)、VSS(挥发性悬浮固体)等指标,分析这些指标与上清液中各种形态N元素的变化关系,讨论了N元素变化与各指标的计量关系.结果表明:剩余污泥厌氧发酵过程中总氮的损失的主因足上清液中氨态氮的挥发,同时也存在因硝化、反硝化作用而导致的总氮损失.氨态氮与VSS减少、SCOD增加呈显著线性相关,而总氮变化与它们的相关性相对较差.总氮每损失1 mg的同时,其它指标变化情况为TSS损失约计24.0mg,VSS损失约计34.0 mg,TCOD损失约计68.0 mg,SCOD增加约计44.0 mg.氨态氮增加约计0.40 mg.     

厌氧条件下剩余污泥中磷及相关指标的释放和变化规律

污水处理过程中产生的剩余污泥富含大量的氮磷元素,从剩余污泥中回收磷是解决磷资源日益缺乏的一种有效途径。探寻出剩余污泥中磷的释放规律是实现剩余污泥中磷回收的首要前提。因此,以实际污水处理厂污泥为研究对象,建立污泥停留时间为5d的中试模型系统。通过系统分析5d停留时间的厌氧条件下污泥中污泥浓度、上清液总磷和氨氮浓度的变化情况,为后续的污泥磷回收提供支撑条件。研究结果表明,在中试系统污泥停留时间5d的厌氧条件下,剩余污泥微生物衰亡自溶或被分解,胞内物质释放,从而使固态物质转化为液态,污泥中磷及相关的氮等物质得到了较大的释放,污泥上清液总磷和氨氮质量浓度可分别达到100和40 mg·L^-1以上。所释放出的氮磷浓度足以满足鸟粪石回收氮磷方法所需的最低经济性要求,为污泥进行厌氧消化后采用鸟粪石的方法回收释放的氮磷提供了重要的基础依据。研究中还发现5d停留时间下, SS和VSS都有不同程度的降低,二者分别减少8.34%和10.14%以上,其中VSS的减少量占SS减少量的65%左右。同时,进入厌氧反应系统的初始污泥浓度对于氮磷的释放有着较大的影响,反应系统的SS在6300~7200 mg·L^-1的条件下,磷和氮的单位质量污泥释放量达到最佳,分别达到单位干污泥0.015和0.006 mg·mg^-1。研究结果为剩余污泥中回收氮磷提供了重要的依据。     

Effects of shear force on formation and properties of anoxic granular sludge in SBR

This paper reports the effects of shear force on anoxic granular sludge in sequencing batch reactors （SBR）. The study was carried out in two SBRs （SBR1 and SBR2） in which sodium acetate （200mg COD·L^-1） was used as the sole substrate and sodium nitrate （40 mgNO3-N·L^-1） was employed as the electron acceptor. The preliminary objective of this study was to cultivate anoxic granules in the SBR in order to investigate the effects of shear force on the formation of anoxic granular sludge and to compare the properties of anoxic sludge in the SBR. This study reports new results for the values of average velocity gradient, a measure of the applied shear force, which was varied in the two SBRs （3.79 s^-1 and 9.76 s^-1 for SBR1 and SBR2 respectively）. The important findings of this research highlight the dual effects of shear force on anoxic granules. A low shear force can produce large anoxic granules with high activity and poor settling ability, whereas higher shear forces produce smaller granules with better settling ability and lower activity. The results of this study show that the anoxic granulation is closely related to the strength of the shear force. For high shear force, this research demonstrated that： 1） granules with smaller diameters, high density and good settling ability were formed in the reactor, and 2） granular sludge formed faster than it did in the low shear force reactor （41days versus 76 days）. Once a steady-state has been achieved, the nitrate and COD removal rates were found to be 98% and 80%, respectively. For low shear force, such as was applied in SBR1, this research demonstrated that： 1） the activity of anoxic granular sludge in low shear force was higher than that in high shear force, 2） higher amount of soluble microbial products （SMPs） were produced, and 3） large pores were observed inside the larger granules,which are beneficial for nitrogen gas diffusion. Electron microscopic examination of the anoxic granules in both reactors showed that the morphology of the granules was ellipsoidal with a clear outline. Coccus and rod-shaped bacteria were wrapped by filamentous bacteria on the surface of granule.     

Evaluating the impact of sulfamethoxazole on hydrogen production during dark anaerobic sludge fermentation

● SMX promotes hydrogen production from dark anaerobic sludge fermentation. ● SMX significantly enhances the hydrolysis and acidification processes. ● SMX suppresses the methanogenesis process in order to reduce hydrogen consumption. ● SMX enhances the relative abundance of hydrogen-VFAs producers. ● SMX brings possible environmental risks due to the enrichment of ARGs. The impact of antibiotics on the environmental protection and sludge treatment fields has been widely studied. The recovery of hydrogen from waste activated sludge (WAS) has become an issue of great interest. Nevertheless, few studies have focused on the impact of antibiotics present in WAS on hydrogen production during dark anaerobic fermentation. To explore the mechanisms, sulfamethoxazole (SMX) was chosen as a representative antibiotic to evaluate how SMX influenced hydrogen production during dark anaerobic fermentation of WAS. The results demonstrated SMX promoted hydrogen production. With increasing additions of SMX from 0 to 500 mg/kg TSS, the cumulative hydrogen production elevated from 8.07 ± 0.37 to 11.89 ± 0.19 mL/g VSS. A modified Gompertz model further verified that both the maximum potential of hydrogen production (P_m) and the maximum rate of hydrogen production (R_m) were promoted. SMX did not affected sludge solubilization, but promoted hydrolysis and acidification processes to produce more hydrogen. Moreover, the methanogenesis process was inhibited so that hydrogen consumption was reduced. Microbial community analysis further demonstrated that the introduction of SMX improved the abundance of hydrolysis bacteria and hydrogen-volatile fatty acids (VFAs) producers. SMX synergistically influenced hydrolysis, acidification and acetogenesis to facilitate the hydrogen production.