The nitrogen removal mechanism was studied and analyzed when treating the ammonium-rich landfill leachate by a set of sequencing batch biofilm reactors (SBBRs), which was designed independently. At the liquid temperature of (32 ± 0.4)°C, and after a 58-days domestication period and a 33-days stabilization period, the efficiency of ammonium removal in the SBBR went up to 95%. Highly frequent intermittent aeration suppressed the activity of nitratebacteria, and also eliminated the influence on the activity of anaerobic ammonium oxidation (ANAMMOX) bacteria and nitritebacteria. This influence was caused by the accumulation of nitrous acid and the undulation of pH. During the aeration stage, the concentration of dissolved oxygen was controlled at 1.2–1.4 mg/L. The nitritebacteria became dominant and nitrite accumulated gradually. During the anoxic stage, along with the concentration debasement of the dissolved oxygen, ANAMMOX bacteria became dominant; then, the nitrite that was accumulated in the aeration stage was wiped off with ammonium simultaneously. 相似文献
An aerobic sequencing batch biofilm reactor (SBBR) packed with Bauer rings was used to treat real domestic wastewater for simultaneous nitrification and denitrification. The SBBR is advantageous for creating an anoxic condition, and the biofilm can absorb and store carbon for good nitrification and denitrification. An average concentration of oxygen ranging from 0.8 to 4.0 mg/L was proved very efficient for nitrification and denitrification. Volumetric loads of TN dropped dramatically and effluent TN concentration increased quickly when the concentration of average dissolved oxygen was more than 4.0 mg/L. The efficiency of simultaneous nitrification and denitrification (SND) increased with increasing thickness of the biofilm. The influent concentration hardly affected the TN removal efficiency, but the effluent TN increased with increasing influent concentration. It is suggested that a subsequence for denitrification be added or influent amount be decreased to meet effluent quality requirements. At optimum operating parameters, the TN removal efficiency of 74%–82% could be achieved. 相似文献
SBBR-CW system was proposed to effectively treat wastewater containing TCBPA.CW unit contributed more than SBBR to the removal of TCBPA.TCBPA changed the composition and structure of bacterial community in the system.GAOs massively grew in SBBR, but did not deteriorate TP removal efficiency. Tetrachlorobisphenol A (TCBPA) released into the sewage may cause environmental pollution and health risk to human beings. The objective of this study was to investigate the removal of TCBPA and bacterial community structures in a laboratory-scale hybrid sequencing biofilm batch reactor (SBBR)-constructed wetland (CW) system. The results showed that the removal efficiency of chemical oxidation demand (COD), ammonia, total nitrogen and total phosphorus in the SBBR-CW system was 96.7%, 97.3%, 94.4%, and 88.6%, respectively. At the stable operation stage, the system obtained a 71.7%±1.8% of TCBPA removal efficiency with the influent concentration at 200 mg/L. Illumina MiSeq sequencing of 16S rRNA gene revealed that the presence of TCBPA not only reduced the bacterial diversity in the SBBR-CW system, but also altered the composition and structure of bacterial community. After the addition of TCBPA, Proteobacteria increased from 31.3% to 38.7%, while Acidobacteria and Parcubacteria decreased greatly in the SBBR. In contrast, Acidobacteria replaced Proteobacteria as the dominant phylum in the upper soils of CW. The results indicated that TCBPA stimulated the growth of GAOs in the SBBR without deteriorating the phosphorus removal due to the presence of sufficient carbon sources. The ammonia oxidizing bacteria, Nitrosomonas, and denitrification bacteria, Hyphomicrobium and Pseudomonas, were inhibited by TCBPA, resulting in a decreasing the removal efficiency of TN and ammonia. 相似文献
In this paper, a study was conducted on the effect of polyhydroxyalkanoates (PHA) and glycogen transformations on biologic nitrogen and phosphorus removal in low dissolved oxygen (DO) systems. Two laboratory-scale sequencing batch reactors (SBR1 and SBR2) were operating with anaerobic/aerobic (low DO, 0.15–0.45 mg·L-1) configurations, which cultured a propionic to acetic acid ratio (molar carbon ratio) of 1.0 and 2.0, respectively. Fewer poly-3-hydroxybutyrate (PHB), total PHA, and glycogen transformations were observed with the increase of propionic/acetic acid, along with more poly-3-hydroxyvalerate (PHV) and poly-3-hydroxy-2-methyvalerate (PH2MV) shifts. The total nitrogen (TN) removal efficiency was 68% and 82% in SBR1 and SBR2, respectively. In the two SBRs, the soluble ortho-phosphate (SOP) removal efficiency was 94% and 99%, and the average sludge polyphosphate (poly-P) content (g·g-MLVSS-1) was 8.3% and 10.2%, respectively. Thus, the propionic to acetic acid ratio of the influent greatly influenced the PHA form and quantity, glycogen transformation, and poly-P contained in activated sludge and further determined TN and SOP removal efficiency. Moreover, significant correlations between the SOP removal rate and the (PHV+ PH2MV)/PHA ratio were observed (R2>0.99). Accordingly, PHA and glycogen transformations should be taken into account as key components for optimizing anaerobic/aerobic (low DO) biologic nitrogen and phosphorus removal systems. 相似文献
A ratio control strategy has been used to demonstrate the feasibility of this automatic control procedure for the achievement of stable full and partial nitritation. The control strategy assured constant ratio between the dissolved oxygen (DO) and the total ammonia nitrogen (TAN) concentrations in the bulk liquid of aerobic granular sludge reactors operating in continuous mode. Three different set-ups with different reactor capacities were used (3, 110, and 150 L). High strength synthetic wastewaters and reject water were tested with similar performance. Achieved nitrogen loading rates ranged between 0.4 and 6.1 kgN·m-3·d-1, at temperatures between 20°C and 30°C. Granular sludge and nitritation were stable in the long term continuous operation of the reactors. Suitable stable effluent for Anammox has been obtained using the desired TAN setpoint (i.e. 50% of influent ammonium oxidation). An existing biofilm model developed incorporating the implemented control loops and validated in a previous publication was used to investigate the effects of the ammonium concentration of the influent and the biofilm density on the achievement of full nitritation. The model demonstrated how sludge recirculation events led to a stable and significant increase of the biomass concentration in the reactor, which in turn resulted in the achievement of high nitrogen loading rates, due to the action of the control strategy. The model predicted an enhancement of stable full nitritation at higher ammonium concentrations in the influent. Poor influence of the biofilm density in the achievement of full nitritation was predicted with the model. 相似文献
Since eutrophication has become increasingly severe in China, nitrogen and phosphorous have been the concern of wastewater treatment, especially nitrogen removal. The stabilization of the intelligent control system and nitrogen removal efficiency were investigated in a pilot-scale aerobic-anoxic sequencing batch reactor (SBR) with a treatment capacity of 60 m3/d. Characteristic points on the profiles of dissolved oxygen (DO), pH, and oxidation reduction potential (ORP) could exactly reflect the process of nitrification and denitrification. Using the intelligent control system not only could save energy, but also could achieve advanced nitrogen removal. Applying the control strategy water quality of the effluent could stably meet the national first discharge standard during experiment of 10 months. Even at low temperature (t = 13°C), chemical oxygen demand (COD) and total nitrogen (TN) in the effluent were under 50 and 5 mg/L, respectively. 相似文献
Algal biofilmtechnology is a new and advanced wastewater treatment method. Experimental study on removing nitrogen and phosphorus from simulated wastewater using algal biofilm under the continuous light of 3500 Lux in the batch and continuous systems was carried out in this paper to assess the performance of algal biofilm in removing nutrients. The results showed that the effect of removing nitrogen and phosphorus by algal biofilm was remarkable in the batch system. The removal efficiencies of total phosphorus (TP), total nitrogen (TN), ammonia-nitrogen (NH3-N), and chemical oxygen demand (COD) reached 98.17%, 86.58%, 91.88%, and 97.11%, respectively. In the continuous system, hydraulic retention time (HRT) of 4 days was adopted; the effects of removing TP, TN, NH3-N, and COD by algal biofilm were very stable. During a run of 24 days, the removal efficiencies of TP, TN, NH3-N, and COD reached 95.38%, 83.93%, 82.38%, and 92.31%, respectively. This study demonstrates the feasibility of removing nitrogen and phosphorus from simulated wastewater using algal biofilm. 相似文献
A membrane-aerated biofilm reactor was employed to investigate the nitrogen removal of one typical municipal reverse osmosis(RO) concentrate with a high total nitrogen (TN) concentration and a low C/ N ratio. The effects of operational conditions, including the aeration pressure, the hydraulic retention time and the C/N ratio, on the systematic performance were evaluated. The nitrogen removal mechanism was evaluated by monitoring the effluent concentrations of nitrogen contents. Furthermore, the microbial tolerance with elevated salinity was identified. The results indicated that the optimal TN removal efficiency of 79.2% was achieved of the aeration pressure of 0.02 MPa, hydraulic retention time of 24 h, and the C/N ratio of 5.8, respectively. It is essential to supplement the carbon source for the targeted RO concentrate to promote the denitrification process. The inhibitory effect of salinity on denitrifying bacteria and nitrite oxidizing bacteria was significant, revealing the limited TN removal capacity of the conditions in this work. The TN removal efficiency remained more than 70% with the addition of salt (NaCl) amount below 20 g/L. This work preliminarily demonstrated the MABR feasibility for the nitrogen removal of municipal RO concentrate with low C/N ratio and provided technical guidance for further scale-up application.
The feasibility of pH and oxidation reduction potential (ORP) as on-line control parameters to advance nitrogen removal in pulsed sequencing batch reactors (SBR) was evaluated. The pulsed SBR, a novel operational mode of SBR, was utilized to treat real municipal wastewater accompanied with adding ethanol as external carbon source. It was observed that the bending-point (apex and knee) of pH and ORP profiles can be used to control denitrification process at a low influent C/N ratio while dpH/dt can be used to control the nitrification and denitrification process at a high influent C/N ratio. The experimental results demonstrated that the effluent total nitrogen can be reduced to lower than 2 mg/L, and the average total nitrogen (TN) removal efficiency was higher than 98% by using real-time controll strategy. 相似文献
COD/N at low ratios (0–0.82) improved N removals of CANON.CANON performance decreased after COD/N up to 0.82.The relative abundance of AOB decreased continuously with increasing COD/N.AOB outcompeted at a high COD load led to CANON failure.The relative abundance of AnAOB decreased and increased with increasing COD/N. The effects of increasing COD/N on nitrogen removal performance and microbial structure were investigated in a SBR adopting a completely autotrophic nitrogen removal over nitrite process with a continuous aeration mode (DO at approximately 0.15–0.2 mg/L). As the COD/N increased from 0.1 to≤0.59, the nitrogen removal efficiency (NRE) increased from 88.7% to 95.5%; while at COD/N ratios of 0.59–0.82, the NRE remained at 90.7%–95.5%. As the COD/N increased from 0.82 to 1.07, the NRE decreased continuously until reaching 60.1%. Nitrosomonas sp. (AOB) and CandidatusJettenia (anammox bacteria) were the main functional genera in the SBR. As the COD/N increased from 0.10 to 1.07, the relative abundance of Nitrosomonas decreased from 13.4% to 2.0%, while that of CandidatusJettenia decreased from 35% to 9.9% with COD/N<0.82 then increased to 45.4% at a COD/N of 1.07. Aerobic heterotrophic bacteria outcompeted AOB at high COD loadings (650 mg/L) because of oxygen competition, which ultimately led to deteriorated nitrogen removal performance. 相似文献
Batch experiments were conducted to study the short-term biological effects of rare earth ions (La3+, Ce3+) and their mixture on the nitrogen removal in a sequencing batch reactor (SBR). The data showed that higher NH+4―N removal rate, total inorganic nitrogen removal efficiency, and denitrification efficiency were achieved at lower concentrations of rare earth elements (REEs) (<1mg/L). In the first hour of the aeration stage of SBR, the presence of REEs increased the total inorganic nitrogen removal efficiency and NH+4―N removal efficiency by 15.7% and 10%―15%, respectively. When the concentrations of REEs were higher than 1mg/L, the total inorganic nitrogen removal efficiency decreased, and nitrate was found to accumulate in the effluent. When the concentrations of REEs was up to 50.0mg/L, the total inorganic nitrogen removal efficiency was less than 30% of the control efficiency with a high level of nitrate. Lower concentrations of REEs were found to accelerate the nitrogen conversion and removal in SBR. 相似文献
A pilot-scale anaerobic ammonia oxidation (ANAMMOX) reactor was used to treat mixed wastewater resulting from a chlortetracycline and starch production process. The results, collected over the course of 272 days, show that the ratio of influent ammonium to nitrite, pH, and temperature can all affect the efficiency of nitrogen removal. The ratio of influent ammonium to nitrite was maintained at about 1:1 at a concentration below 200 mg·L-1 for both influent ammonium and nitrite. The total nitrogen (TN) loading rate was 0.15–0.30 kgN·m-3·d-1, pH remained at 7.8–8.5, and temperature was recorded at 33±1°C. The rate of removal of ammonia, nitrite, and TN were over 90%, 90%, and 80%, and the effluent ammonium, nitrite and TN concentrations were below 50, 30, and 100 mg·L-1. 相似文献
Among the numerous parameters affecting the membrane bioreactor (MBR) performance, the aeration intensity is one of the most important factors. In the present investigation, an anoxic/aerobic-type (A/O-type) sequencing batch MBR system, added anoxic process as a pretreatment to improve the biodegradability of azo dye wastewater, was investigated under different aeration intensities and the impact of the aeration intensity on effluent quantity, sludge properties, extracellular polymeric substances (EPS) amount generated as well as the change of permeation flux were examined. Neither lower nor higher aeration intensities could improve A/O-type sequencing batch MBR performances. The results showed 0.15 m3·h-1 aeration intensity was promising for treatment of azo dye wastewater under the conditions examined. Under this aeration intensity, chemical oxygen demand (COD), ammonium nitrogen and color removal as well as membrane flux amounted to 97.8%, 96.5%, 98.7% and 6.21 L·m-2·h-1, respectively. The effluent quality, with 25.0 mg·L-1COD, 0.84 mg·L-1 ammonium nitrogen and 8 chroma, could directly meet the reuse standard in China. In the meantime, the sludge relative hydrophobicity, the bound EPS, soluble EPS and EPS amounts contained in the membrane fouling layer were 70.3%, 52.0 mg·g-1VSS, 38.8 mg·g-1VSS and 90.8 mg·g-1VSS, respectively, which showed close relationships to both pollutant removals and membrane flux. 相似文献