中国2030年能源发展预测与对策研究

在回顾2000年-2010年中国能源消费的基础上,对中国2030年能源发展及耗煤量进行了预测,预测结果表明,2030年中国能耗总量将控制在55～60亿t标煤,耗煤量控制在40～45亿t标煤。建议中国2011年-2015年、2015年-2020年、2020年-2025年和2025年-2030年能源弹性系数分别为0.5、0.5、0.4和0.3。开展煤炭休养生息战略,多进口煤炭。     

中国2015年SO2排放总量宏观控制目标研究

1980年中国SO2排放量为1160万吨,2005年为2549万吨,伴随节能减排政策的实施和s02治理投资的增加,到2010年我国SO2排放量将降至2300万吨（削减10％）,仍位居世界第一位。在“十二五”期间,伴随人口、经济、能源的增长和发展模式的重大转变,我国2015年SO2排放总量面临微增长、不增长或减排的趋势。应用我国SO2减排宏观控制指标和模式预测了我国2015年SO2排放总量的4种图像或目标。提出了实现SO2排放总量削减10％目标的10条建议。     

流化床富氧焚烧含油污泥技术经济性分析

介绍了流化床富氧焚烧含油污泥技术的流程和优势,计算了富氧焚烧含油污泥系统主要设备的电耗和技术经济指标。流化床富氧焚烧含油污泥技术可实现烟气及其他污染物零排放,产生的蒸汽可直接供应油田生产和生活使用,产生的液态CO2可直接用于油井驱油,烟气中的SO2和NOx可转化为硫酸和硝酸。采用日处理200 t含油污泥的流化床锅炉年处理含油污泥量约73 kt,每年减少排污费7 300万元;锅炉年产蒸汽量约177 kt,每年节约蒸汽费用1 380.6万元,合计每年节约成本8 680.6万元。回收得到质量分数为40%的稀硫酸5.56 t/d,质量分数为37%的硝酸0.708 t/d,年回收CO2约99 kt。     

Brazilian banana,guava, and orange fruit and waste production as a potential biorefinery feedstock

Journal of Material Cycles and Waste Management - Fruit production worldwide is over 675 million tons per year. Brazil is responsible for the production of 43.6 million tons of fruits per year,...     

灰场回水减少的原因分析及对策

针对老燃煤发电厂贮灰场回水逐年减少的状况，采取了在贮灰场水面上安装可移动式漂浮筏的措施，作为灰场回水取水的漂浮泵站，增加了灰场回水流量，解决了因回水不足而使用水库水作补水的问题。     

First-order kinetic gas generation model parameters for wet landfills

Landfill gas collection data from wet landfill cells were analyzed and first-order gas generation model parameters were estimated for the US EPA landfill gas emissions model (LandGEM). Parameters were determined through statistical comparison of predicted and actual gas collection. The US EPA LandGEM model appeared to fit the data well, provided it is preceded by a lag phase, which on average was 1.5 years. The first-order reaction rate constant, k, and the methane generation potential, L(o), were estimated for a set of landfills with short-term waste placement and long-term gas collection data. Mean and 95% confidence parameter estimates for these data sets were found using mixed-effects model regression followed by bootstrap analysis. The mean values for the specific methane volume produced during the lag phase (V(sto)), L(o), and k were 33 m(3)/Megagrams (Mg), 76 m(3)/Mg, and 0.28 year(-1), respectively. Parameters were also estimated for three full scale wet landfills where waste was placed over many years. The k and L(o) estimated for these landfills were 0.21 year(-1), 115 m(3)/Mg, 0.11 year(-1), 95 m(3)/Mg, and 0.12 year(-1) and 87 m(3)/Mg, respectively. A group of data points from wet landfills cells with short-term data were also analyzed. A conservative set of parameter estimates was suggested based on the upper 95% confidence interval parameters as a k of 0.3 year(-1) and a L(o) of 100 m(3)/Mg if design is optimized and the lag is minimized.     

燃煤电厂电除尘器的节能和提效

介绍了华能北京热电厂液态排渣塔式直流炉4号电除尘器电源控制系统改造后所取得的成果.该电厂采用了ZH2005型控制器,烟尘排放质量浓度达到20mg/m3左右,可节省电费58万元/a,减排粉尘120t/a.     

“十一五”SO2排放总量后评价

＂十一五＂期间在我国国内生产总值（GDP）、能源消费增长均超过规划目标的情况下,2010年全国SO2排放总量为2295万t,完成了在2005年基础上减排10%的规划目标。2010年全国实际SO2去除率为65%,比2005年提高23%。建议＂十二五＂期间将GDP年均增长率控制在7%以下,维持0.5～0.4能源消费弹性系数及0.7～0.6的电力能源消费弹性系数,提高SO2去除率至73%以上;国家有关部门逐年公布GDP年均增长率、能源消费弹性系数、电力能源消费弹性系数和节能减排公报。     

On the Methods for the Delimitation of Seasons

It is well known that air pollution is one of the major factors affecting human health and the activities in a town. Among the various air pollutants an interesting one, especially for sunny climates, is the reactive O₃. O₃ varies significantly through the year; it is therefore very important to know the onset and the duration of the warm period of the year since at that time O₃ concentrations increase significantly. In this work, an attempt was made to determine the onset of warm season of the year as well as its duration in various sites located in Northeastern Mediterranean. For this purpose, a fuzzy clustering method is used. The method was applied on the isobaric thickness between 1000 and 500 hPa for the period from 1974 to 1997. The results were compared to conventional methods based on synoptic classification and were found to be in good agreement.     

Contaminant mass flux and forensic assessment of polycyclic aromatic hydrocarbons: Tools to inform remediation decision making at a contaminated site in Canada

Polycyclic aromatic hydrocarbons (PAHs) and metal(loid) mass flux estimates and forensic assessment using PAH diagnostic ratios were used to inform remediation decision making at the Sydney Tar Ponds (STPs) and Coke Ovens cleanup project in eastern Canada. Environmental effects monitoring of surface marine sediments in Sydney Harbor indicated significantly higher PAH concentrations during the first year of remediation monitoring compared to baseline. This was equivalent to PAH loadings of ～2,000 kg over a 15‐month period. Increases in sediment PAH concentrations raised serious concerns for regulators, who requested cessation of remediation activities early in the $400 M (CAD) project. Historically, the STPs were reported as the primary source of PAH contamination in Sydney Harbor with estimated discharges of 300 to 800 kg/year between 1989 and 2001. Mass flux estimates of PAHs and metal(loid)s and PAH diagnostic ratios were used to evaluate if increases in PAH concentrations in marine sediments were the result of the STPs remediation activities. PAH mass flux estimates approximated that 17 to 97 kg/year were discharged from the STPs during three years of remediation and were corroborated by an independent PAH flux estimate of 119 kg in year 1. PAH fluxes to the Sydney Harbor were mostly surface water derived, with groundwater contributing negligible quantities (0.002–0.005 kg/year). Fluxes of metal(loid)s to harbor sediments were stable or declining across all years and were mirrored in sediment metal(loid) concentrations, which lacked temporal variation, unlike total PAH concentrations. Flux results were also corroborated using PAH diagnostic ratios, which found a common source of PAHs. Coal combustion was likely the principal source of PAHs and not migration from the STPs during remediation. Although short‐term residual sediment PAH increases during onset of remediation raised concerns for regulators, calls for premature cessation of remediation early in the project were unwarranted based on only one year of monitoring data. Mass flux estimates and forensic assessments using PAH diagnostic ratios proved useful tools to inform remediation decision making that helped environmental protection and reduced costs associated with lost cleanup time.     

The influence of atmospheric pressure on landfill methane emissions

Landfills are the largest source of anthropogenic methane (CH4) emissions to the atmosphere in the United States. However, few measurements of whole landfill CH4 emissions have been reported. Here, we present the results of a multi-season study of whole landfill CH4 emissions using atmospheric tracer methods at the Nashua, New Hampshire Municipal landfill in the northeastern United States. The measurement data include 12 individual emission tests, each test consisting of 5-8 plume measurements. Measured emissions were negatively correlated with surface atmospheric pressure and ranged from 7.3 to 26.5 m3 CH4 min(-1). A simple regression model of our results was used to calculate an annual emission rate of 8.4 x 10(6) m3 CH4 year(-1). These data, along with CH4 oxidation estimates based on emitted landfill gas isotopic characteristics and gas collection data, were used to estimate annual CH4 generation at this landfill. A reported gas collection rate of 7.1 x 10(6) m3 CH4 year(-1) and an estimated annual rate of CH4 oxidation by cover soils of 1.2 x 10(6) m3 CH4 year(-1) resulted in a calculated annual CH4 generation rate of 16.7 x 10(6) m3 CH4 year(-1). These results underscore the necessity of understanding a landfill's dynamic environment before assessing long-term emissions potential.     

Seasonal characterization of municipal solid waste (MSW) in the city of Chihuahua,Mexico

Management of municipal solid waste (MSW) has become a significant environmental problem, especially in fast-growing cities. The amount of waste generated increases each year and this makes it difficult to create solutions which due to the increase in waste generation year after year and having to identify a solution that will have minimum impact on the environment. To determine the most sustainable waste management strategy for Chihuahua, it is first necessary to identify the nature and composition of the city’s urban waste. The MSW composition varied considerably depending on many factors, the time of year is one of them. Therefore, as part of our attempt to implement an integral waste management system in the city of Chihuahua, we conducted a study of the characteristics of MSW composition for the different seasons. This paper analyzes and compares the findings of the study of the characterization and the generation of solid waste from households at three different socio-economic levels in the city over three periods (April and August, 2006 and January, 2007).The average weight of waste generated in Chihuahua, taking into account all three seasons, was 0.592 kg capita^?1 day^?1. Our results show that the lowest income groups generated the least amount of waste. We also found that less waste was generated during the winter season. The breakdown for the composition of the waste shows that organic waste accounts for the largest proportion (45%), followed by paper (17%) and others (16%).     

Projecting the environmental profile of Singapore's landfill activities: Comparisons of present and future scenarios based on LCA

This article aims to generate the environmental profile of Singapore's Semakau landfill by comparing three different operational options associated with the life cycle stages of landfilling activities, against a 'business as usual' scenario. Before life cycle assessment or LCA is used to quantify the potential impacts from landfilling activities, an attempt to incorporate localized and empirical information into the amounts of ash and MSW sent to the landfill was made. A linear regression representation of the relationship between the mass of waste disposed and the mass of incineration ash generated was modeled from waste statistics between years 2004 and 2009. Next, the mass of individual MSW components was projected from 2010 to 2030. The LCA results highlighted that in a 'business as usual' scenario the normalized total impacts of global warming, acidification and human toxicity increased by about 2% annually from 2011 to 2030. By replacing the 8000-tonne barge with a 10000-tonne coastal bulk carrier or freighter (in scenario 2) a grand total reduction of 48% of both global warming potential and acidification can be realized by year 2030. Scenario 3 explored the importance of having a Waste Water Treatment Plant in place to reduce human toxicity levels - however, the overall long-term benefits were not as significant as scenario 2. It is shown in scenario 4 that the option of increased recycling championed over all other three scenarios in the long run, resulting in a total 58% reduction in year 2030 for the total normalized results. A separate comparison of scenarios 1-4 is also carried out for energy utilization and land use in terms of volume of waste occupied. Along with the predicted reductions in environmental burdens, an additional bonus is found in the expanded lifespan of Semakau landfill from year 2032 (base case) to year 2039. Model limitations and suggestions for improvements were also discussed.     

Quantitative characterization of recyclable resources dismantled from waste liquid crystal display products

Currently only limited materials, such as common metals and plastics, are recovered from waste flat-panel displays, thus necessitating the development of a comprehensive recycling process. This study aims to establish a statistical database about the types and amounts of valuable resources in waste liquid crystal display (LCD) products. To obtain these data, the waste LCD products were disassembled into four components: plastics, printed circuit boards, metals, and other materials, including their panels, and the weight of each component was measured. Overall, the product weight decreased with increasing manufacturing year regardless of the product screen size; however, the decreasing rate varied from 14 to 73%. The metal weight ratios decreased significantly by 24–31%. Meanwhile, regardless of the manufacturing year, the plastic weight ratios remained almost constant at about 20%. On the other hand, the weight ratio of the other components increased by 26–46% with increasing manufacturing year suggesting that rare-earth metal recycling has become more important. These statistical analyses are expected to contribute to the development of an eco-friendly, high-efficiency dismantling/separation process that will enable higher value recycling and minimal waste disposal.     

The contemporary cement cycle of the United States

A country-level stock and flow model for cement, an important construction material, was developed based on a material flow analysis framework. Using this model, the contemporary cement cycle of the United States was constructed by analyzing production, import, and export data for different stages of the cement cycle. The United States currently supplies approximately 80% of its cement consumption through domestic production and the rest is imported. The average annual net addition of in-use new cement stock over the period 2000–2004 was approximately 83 million metric tons and amounts to 2.3 tons per capita of concrete. Nonfuel carbon dioxide emissions (42 million metric tons per year) from the calcination phase of cement manufacture account for 62% of the total 68 million tons per year of cement production residues. The end-of-life cement discards are estimated to be 33 million metric tons per year, of which between 30% and 80% is recycled. A significant portion of the infrastructure in the United States is reaching the end of its useful life and will need to be replaced or rehabilitated; this could require far more cement than might be expected from economic forecasts of demand for cement.     

Emission inventory of deca-brominated diphenyl ether (DBDE) in Japan

Atmospheric emissions of deca-brominated diphenyl ether (DBDE) in Japan were estimated based on the material flow of DBDE products and their emission factors. In 2002, the demand for DBDE in Japan was 2200 ton/year and the stock level was about 60 000 ton. The DBDE flow into the waste stream was estimated to be about 6000 ton/year and the flow out through second-hand product exports was more than 700 ton/year. Home appliance recycling facilities dismantle and crush domestic wastes containing about 600 ton of DBDE annually. Material recycling of crushed plastics is not commonly practiced as yet. Emission factors from plastics processing (2 × 10⁻⁹–1 × 10⁻⁷), textile processing (9 × 10⁻⁷), home appliance recycling (8 × 10⁻⁹–5 × 10⁻⁶), and waste incineration (1 × 10⁻⁷–2 × 10⁻⁶) were estimated using field measurement data. The DBDE emission rate through house dust during the service life of final products (2 × 10⁻⁷–9 × 10⁻⁷ per year) was estimated using the DBDE concentration in dust and the amount of dust in used televisions. Emission factors from previous studies were also used. The estimated total DBDE emission was 170–1800 kg/year. These results suggest the necessity of characterizing emissions during the service life of products, which is essential information for formulating an appropriate e-waste recycling strategy.     

新疆某油田企业两轮清洁生产审核效益分析

新疆某油田企业于2007年进行了第一轮清洁生产审核工作,确定了清洁生产方案14项,其中无／低费方案9项,中／高费方案5项,产生的直接、间接经济效益总计为4057．27万元／a。该企业于2011年完成了第二轮清洁生产审核,确定了清洁生产方案14项,其中无／低费方案6项,中／高费方案8项,总计清洁生产方案产生经济效益1954．142万元／a。通过两轮清洁生产审核工作,企业产生了较好的经济效益与环境效益。     

Utilization of river sediment,sewage sludge and wheat straw as the primary raw material in sintered-shale bricks

Journal of Material Cycles and Waste Management - China produces large amounts of sewage sludge and agricultural waste every year. In line with the concepts of economic and environmental...     

Two-year performance by evapotranspiration covers for municipal solid waste landfills in northwest Ohio

Evapotranspiration (ET) covers have gained interest as an alternative to conventional covers for the closure of municipal solid waste (MSW) landfills because they are less costly to construct and are expected to have a longer service life. Whereas ET covers have gained acceptance in arid and semi-arid regions (defined by a precipitation (P) to potential evapotranspiration (PET) ratio less than 0.75) by meeting performance standards (e.g. rate of percolation), it remains unclear whether they are suitable for humid regions (P:PET greater than 0.75). The goal of this project is to extend their application to northwest Ohio (P:PET equals 1.29) by designing covers that produce a rate of percolation less than 32 cm yr^?1, the maximum acceptable rate by the Ohio Environmental Protection Agency (OEPA). Test ET covers were constructed in drainage lysimeters (1.52 m diameter, 1.52 m depth) using dredged sediment amended with organic material and consisted of immature (I, plants seeded onto soil) or mature (M, plants transferred from a restored tall-grass prairie) plant mixtures. The water balance for the ET covers was monitored from June 2009 to June 2011, which included measured precipitation and percolation, and estimated soil water storage and evapotranspiration. Precipitation was applied at a rate of 94 cm yr^?1 in the first year and at rate of 69 cm yr^?1 in the second year. During the first year, covers with the M plant mixture produced noticeably less percolation (4 cm) than covers with the I plant mixture (17 cm). However, during the second year, covers with the M plant mixture produced considerably more percolation (10 cm) than covers with the I plant mixture (3 cm). This is likely due to a decrease in the aboveground biomass for the M plant mixture from year 1 (1008 g m^?2) to year 2 (794 g m^?2) and an increase for the I plant mixture from year 1 (644 g m^?2) to year 2 (1314 g m^?2). Over the 2-year period, the mean annual rates of percolation for the covers with the M and I plant mixtures were 7 and 8 cm yr^?1, which are below the OEPA standard. The results suggest the application of ET covers be extended to northwest Ohio and other humid regions.     

Retro-techno-economic evaluation of acetic acid production using cotton stalk as feedstock

In value-added chemical industries, use of agricultural wastes as raw materials remains to be a major challenge in commercialization due to lack of competitiveness with respect to petrochemical processes. This work presents the techno-economic analysis of a novel bioprocessing plant converting 356,400 MT/year cotton stalks into 147,000 MT/year acetic acid. A production scheme integrating lignin separation with the main bioconversion stages has been proposed. Techno-economic assessment was performed through economic feasibility and retro-techno-economic analysis (RTEA) methods. The RTEA method has been extended to include the estimation of research and development funding for improving economic feasibility. Carbon offset of the proposed technology has been estimated and carbon credit results have been incorporated into the economic feasibility metrics.