切割刃料碳化硅的再生处理工艺研究

采用化学反应除杂和水力沉降粒度重新分级的方法,通过酸洗、碱洗、水力分级、pH值调节、干燥、配料等一系列处理工艺,对废砂浆中的碳化硅进行再生处理,得到的再生切割刃料各项性能指标满足切割工业使用要求,实现了资源再利用和循环发展.     

Recovery of silicon powder from kerf loss slurry waste using superconducting high gradient magnetic separation technology

A major challenge in recycling of silicon powder from kerf loss slurry waste is the complete removal of metal particles. The traditional acid leaching method is costly and not green. In this paper, a novel approach to recover high-purity Si from the kerf loss slurry waste of solar grade silicon was investigated. The metal impurities were removed with superconducting high gradient magnetic separation technology. The effects of process parameters such as magnetic flux density, slurry density, and slurry flow velocity on the removal efficiency were investigated, and the parameters were optimized. In one lot of control experiments, the silicon content was increased from 90.91 to 95.83%, iron content reduced from 3.24 to 0.57%, and aluminum content from 2.44 to 1.51% under the optimum conditions of magnetic flux density of 4.0 T, slurry density of 20 g/L, and slurry flow velocity of 500 mL/min. The result indicates that the superconducting high gradient magnetic separation technology is a feasible purifying method, and the magnetic separation concentrate could be used as an intermediate product for high-purity Si powder.

     

非高温法提取粉煤灰中铝和硅的试验研究

在试验的基础上，提出了一套常湿法提取粉煤灰中铝和硅的工艺流程，基本解决了目前国内外用相近方法提取煤灰中铝和硅，但浸出率不高的问题。     

硅晶切割砂绿色再生工艺装备的运行特性研究

针对硅晶切割过程中产生的切割废砂浆的资源化回收问题,建立了每小时处理1t废砂饼的绿色再生工艺装备.通过工业试运行,实现了水资源的循环利用,回收的硅晶切割砂纯度达到97％,6～11 μm粒径切割砂的集中度大于78％,6μm以上的切割砂全部实现了回收.该工艺过程不消耗酸碱,节约了化学资源的消耗,从源头上消除了废酸、废碱的污染,是回收硅晶切割砂的一种理想工艺装备.     

Influence of sludge characteristics on coagulant recovery from water treatment sludge: a preliminary study

Journal of Material Cycles and Waste Management - This study investigated the effect of raw water quality and coagulant type and dosage on the efficiency of aluminium recovery from water treatment...     

平板陶瓷膜回收烟气水热的实验研究

将平板陶瓷膜组成膜组件对烟气水分和余热进行回收,考察了烟气的温度、相对湿度、流速和冷却水温度等参数对膜组件水热回收性能的影响。在实验工况下,水通量和水回收效率随着烟气温度、烟气相对湿度的增加和冷却水温度的降低而上升;水通量随着烟气流速的加快而上升,水回收效率随着烟气流速的加快先上升后降低;膜组件的水通量和水回收效率最高分别可达22.0 kg/(m²·h)和36.3%。平板陶瓷膜回收的热量主要来自烟气潜热,烟气潜热换热量与水通量呈正相关变化趋势。在实验工况下,平板陶瓷膜组件的总传热系数最高为412 W/(m²·℃),高于多通道管式陶瓷膜和单通道管式陶瓷膜。     

浅析石灰石浆液品质调节方法与制浆系统节能

燃煤电厂烟气脱硫技术以石灰石/石膏法为主,制浆系统是其重要组成之一。以金湾电厂2×600MW机组石灰石/石膏湿法脱硫制浆系统为例,介绍了石灰石浆液品质调节方法及制浆系统节能措施。     

从银铅锌废渣中回收硝酸银的研究

介绍了用灼烧、浸取、沉淀、溶转和离子交换等方法,从银铅锌废渣中直接回收硝酸银,收率可达80.12%,AgNO3纯度为99.9%。考察了试料粒度、FeCl3质量浓度、溶液酸度、固液比,反应温度及浸取时间对银浸出率的影响。     

A full-scale study of treatment of pig slurry by composting: kinetic changes in chemical and microbial properties

Since the indiscriminate disposal of pig slurry can cause not only air pollution and bad odours but also nutrient pollution of ground waters and superficial waters, composting is sometimes used as one environmentally acceptable method for recycling pig manure. The aim of this study was to evaluate the effect of composting pig slurry on its sanitation (evaluated by ecotoxicity assays and pathogen content determination), as well as to determine the effect of a carbon-rich bulking agent (wood shavings, WS) and the starting C/N ratio on the changes undergone by different chemical (volatile organic matter, C and N fractions) and microbiological (microbial biomass C, ATP, dehydrogenase activity, urease, protease, phosphatase, and beta-glucosidase activities) parameters during composting. Pig slurry mixed with bulking agent (P+WS) and the solid faction separated from it, both with (PSF+WS) and without bulking agent (PSF), were composted for 13 weeks. Samples for analysis were taken from composting piles at the start of the process and at 3, 6, 9, and 13 weeks after the beginning of composting. The total organic carbon, water soluble C and ammonium content decreased with composting, while Kjeldahl N and nitrate content increased. The nitrification process in the PSF+WS pile was more intense than in the PSF or P+WS composting piles. The pathogen content decreased with composting, as did phytotoxic compounds, while the germination index increased with compost age. Piles with bulking agent showed higher values of basal respiration, microbial biomass carbon, ATP and hydrolase activities during the composting process than piles without bulking agent.     

Energy recovery from municipal waste: a case study for a middle-sized Italian district

This paper reports the main outcome of research to compare and assess the merits of alternative strategies for energy recovery from municipal solid waste downstream of material recovery for an Italian province. Strategies analysed are based on well-established combustion technologies available at the commercial scale in the Italian market in comparison with an innovative but not yet proven option of refuse derived fuel gasification and subsequent co-combustion of syngas in a combined cycle power plant. The comparison is made using mass and energy balances, environmental assessment and economic analysis. From an energetic point of view, the best strategy is the one based on the refuse derived fuel gasification, which, on the contrary, does not show interesting environmental results. In this perspective, the best results are from strategies based on a dedicated plant, particularly when unsorted residual waste collected downstream of material recovery is used. Finally, from an economic point of view, the strategy with gasification allows the highest revenues from the sale of energy.     

Effect of persistent trace compounds in landfill gas on engine performance during energy recovery: A case study

Performances of gas engines operated with landfill gas (LFG) are affected by the impurities in the LFG, reducing the economic viability of energy recovery. The purpose of this study was to characterize the trace compounds in the LFG at the Odayeri Landfill, Istanbul, Turkey which is used for energy recovery. Composite gas samples were collected and analyzed for trace compounds (hydrocarbons, siloxanes, and volatile halogenated hydrocarbons) over a 3-year period. Trace compounds entering the gas engines, their impact on the engine performance were evaluated. The operational problems included deposit formation in the combustion chamber, turbocharger, and intercooler of engine before the scheduled maintenance times. High levels of hydrogen sulfide, as well as chlorinated and fluorinated compounds cause corrosion of the engine parts and decrease life of the engine oils. Persistence of siloxanes results in deposit formation, increasing engine maintenance costs. Pretreatment of LFG is necessary to protect the engines at the waste-to-energy facilities with persistence levels of siloxanes and volatile halogenated hydrocarbons.     

A facile method of resource recovery from bauxite residue by phosphoric acid treatment

Journal of Material Cycles and Waste Management - Bauxite residue (BR) is an industrial waste from alumina refineries. Despite being comprised of valuable secondary materials, utilization of BR is...     

Development of combined plant of biogas and bio solid-refuse-fuel from swine manure slurry

Journal of Material Cycles and Waste Management - An environment-friendly treatment of organic waste like swine manure and food waste is considered to be big challenge, because the residue of...     

Yttrium recovery from primary and secondary sources: A review of main hydrometallurgical processes

Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority.The present review summarized the main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes. Before to discuss the works about the treatment of wastes, the processes to retrieval Y from ores are discussed, since the processes are similar and derived from those already developed for the extraction from primary sources.Particular attention was given to the recovery of Y from WEEE because the recycle of them is important not only for economical point of view, considering its value, but also for environmental impact that this could be generated if not properly disposal.     

Eco-efficiency assessment of options for metal recovery from incineration residues: A conceptual framework

Residues from municipal solid waste (MSW) incineration in Switzerland have been a hot topic in recent years, both in the research and practice communities. Regarded by many as an economically and environmentally sound solution to this issue, technological retrofitting of existing grate incinerators has the dual purpose of enhancing the metal recovery of bottom and fly ashes and improving the inertization of residues to be landfilled. How does context influence the economic and environmental performance of this particular technological option? Under which conditions would this technological option be implemented nationwide in the future? What are stakeholders’ views on sustainable transitions of MSW incineration? We propose a three-stage methodological procedure to address these questions.     

废镉镍电池再资源化研究新进展

废镉镍电池再资源化研究具有重大的社会、环境及经济效益.火法及湿法再资源化技术各具特色.利用废镉镍电池制备Ni-Zn系软磁铁氧体材料是今后一个时期废镉镍电池再资源化的发展方向.     

An overview of recovery of metals from slags

Various slags are produced as by-products in metallurgical processes or as residues in incineration processes. According to the origins and the characteristics, the main slags can be classified into three categories, namely ferrous slag, non-ferrous slag and incineration slag. This paper analysed and summarised the generation, characteristics and application of various slags, and discussed the potential effects of the slags on the environment. On this basis, a review of a number of methods for recovery of metals from the slags was made. It can be seen that a large amount of slags is produced each year. They usually contain a quantity of valuable metals except for blast furnace slag and they are actually a secondary resource of metals. By applying mineral processing technologies, such as crushing, grinding, magnetic separation, eddy current separation, flotation and so on, leaching or roasting, it is possible to recover metals such as Fe, Cr, Cu, Al, Pb, Zn, Co, Ni, Nb, Ta, Au, and Ag etc. from the slags. Recovery of metals from the slags and utilisation of the slags are important not only for saving metal resources, but also for protecting the environment.     

The use of commercial and industrial waste in energy recovery systems - A UK preliminary study

With 2020 energy targets set out by the EU fast approaching, the UK is trying to source a higher proportion of its energy from renewable resources. Coupled with this, a growing population and increasing trends in consumer demand have resulted in national waste loads increasing. A possible solution to both issues is energy-from-waste (EfW) technologies. Many studies have focused on municipal solid waste (MSW) as a potential feedstock, but appear to overlook the potential benefits of commercial and industrial waste (C&IW). In this study, samples of C&IW were collected from three North West waste management companies and Lancaster University campus. The samples were tested for their gross and net calorific value, moisture content, ash content, volatile matter, and also elemental composition to determine their suitability in EfW systems. Intra-sample analysis showed there to be little variation between samples with the exception two samples, from waste management site 3, which showed extensive variation with regards to net calorific value, ash content, and elemental analysis. Comparisons with known fuel types revealed similarities between the sampled C&IW, MSW, and refuse derived fuel (RDF) thereby justifying its potential for use in EfW systems. Mean net calorific value (NCV) was calculated as 9.47 MJ/kg and concentrations of sulphur, nitrogen, and chlorine were found to be below 2%. Potential electrical output was calculated using the NCV of the sampled C&IW coupled with four differing energy generation technologies. Using a conventional incinerator with steam cycle, total electrical output was calculated as 24.9 GWh, based on a plant operating at 100,000 tpa. This value rose to 27.0 GWh when using an integrated gasification combined cycle. A final aspect of this study was to deduce the potential total national electrical output if all suitable C&IW were to be used in EfW systems. Using incineration coupled with a steam turbine, this was determined to be 6 TWh, 1.9% of the national demand thereby contributing 6.5% towards the UK’s 2020 renewable electricity target.