Applying electromagnetic surveys as pre-screening tools prior to open dump mining

Journal of Material Cycles and Waste Management - The electrical resistivity tomography (ERT) survey is a common geophysical survey for characterising waste in final disposal sites. However, the...     

Improvement of electrical resistivity tomography for leachate injection monitoring

Leachate recirculation is a key process in the scope of operating municipal waste landfills as bioreactors, which aims to increase the moisture content to optimize the biodegradation in landfills. Given that liquid flows exhibit a complex behaviour in very heterogeneous porous media, in situ monitoring methods are required. Surface time-lapse electrical resistivity tomography (ERT) is usually proposed. Using numerical modelling with typical 2D and 3D injection plume patterns and 2D and 3D inversion codes, we show that wrong changes of resistivity can be calculated at depth if standard parameters are used for time-lapse ERT inversion. Major artefacts typically exhibit significant increases of resistivity (more than +30%) which can be misinterpreted as gas migration within the waste. In order to eliminate these artefacts, we tested an advanced time-lapse ERT procedure that includes (i) two advanced inversion tools and (ii) two alternative array geometries. The first advanced tool uses invariant regions in the model. The second advanced tool uses an inversion with a “minimum length” constraint. The alternative arrays focus on (i) a pole–dipole array (2D case), and (ii) a star array (3D case). The results show that these two advanced inversion tools and the two alternative arrays remove almost completely the artefacts within +/?5% both for 2D and 3D situations. As a field application, time-lapse ERT is applied using the star array during a 3D leachate injection in a non-hazardous municipal waste landfill. To evaluate the robustness of the two advanced tools, a synthetic model including both true decrease and increase of resistivity is built. The advanced time-lapse ERT procedure eliminates unwanted artefacts, while keeping a satisfactory image of true resistivity variations. This study demonstrates that significant and robust improvements can be obtained for time-lapse ERT monitoring of leachate recirculation in waste landfills.     

Application of a contaminant mass balance method at an old landfill to assess the impact on water resources

Old and unlined landfill sites pose a risk to groundwater and surface water resources. While landfill leachate plumes in sandy aquifers have been studied, landfills in clay till settings and their impact on receiving water bodies are not well understood. In addition, methods for quantitatively linking soil and groundwater contamination to surface water pollution are required. This paper presents a method which provides an estimate of the contaminant mass discharge, using a combination of a historical investigation and contaminant mass balance approach. The method works at the screening level and could be part of a risk assessment. The study site was Risby Landfill, an old unlined landfill located in a clay till setting on central Zealand, Denmark. The contaminant mass discharge was determined for three common leachate indicators: chloride, dissolved organic carbon and ammonium. For instance, the mass discharge of chloride from the landfill was 9.4 ton/year and the mass discharge of chloride to the deep limestone aquifer was 1.4 ton/year. This resulted in elevated concentrations of leachate indicators (chloride, dissolved organic carbon and ammonium) in the groundwater. The mass discharge of chloride to the small Risby Stream down gradient of the landfill was approximately 31 kg/year. The contaminant mass balance method worked well for chloride and dissolved organic carbon, but the uncertainties were elevated for ammonium due to substantial spatial variability in the source composition and attenuation processes in the underlying clay till.     

Pollution profiles and physicochemical parameters in old uncontrolled landfills

The long-term effectiveness of the geological barrier beneath municipal-waste landfills is a critical issue for soil and groundwater protection. This study examines natural clayey soils directly in contact with the waste deposited in three landfills over 12 years old in Spain. Several physicochemical and geological parameters were measured as a function of depth. Electrical conductivity (EC), water-soluble organic carbon (WSOC), Cl⁻, NH₄⁺, Na⁺ and exchangeable NH₄⁺ and Na⁺ were used as parameters to measure the penetration of landfill leachate pollution. Mineralogy, specific surface area and cationic-exchange capacities were analyzed to characterize the materials under the landfills. A principal component analysis, combined with a Varimax rotation, was applied to the data to determine patterns of association between samples and variables not evident upon initial inspection. The main factors explaining the variation in the data are related to waste composition and local geology. Although leachates have been in contact with clays for long time periods (13-24 years), WSOC and EC fronts are attenuated at depths of 0.2-1.5 m within the clay layer. Taking into account this depth of the clayey materials, these natural substrata (>45% illite-smectite-type sheet silicates) are suitable for confining leachate pollution and for complying with European legislation. This paper outlines the relevant differences in the clayey materials of the three landfills in which a diffusive flux attenuation capacity (A_c) is defined as a function (1) of the rate of decrease of the parameters per meter of material, (2) of the age and area of the landfill and (3) of the quantity and quality of the wastes.     

ERI evaluation of injectates used at a dry‐cleaning site

A former dry‐cleaning site in Jackson, Tennessee, has undergone remediation to treat dense nonaqueous‐phase liquid (trichloroethene [TCE] and tetrachloroethene [PCE]) contamination in the subsurface. The dry cleaning operation closed in 1977. In 2002, a series of injections were made at the site consisting of corn syrup, vegetable oils, and Simple Green®. In 2004, approximately 200 cubic yards of contaminated soil were excavated, and the bottom of the excavation was covered with sodium lactate. In 2009, the site was characterized using proprietary electrical resistivity imaging (ERI; commercially available as Aestus GeoTrax Surveys^TM). Follow‐up confirmation soil borings targeted anomalies detected via the geophysical work. The results indicate an extremely electrically conductive (less than 1 ohm‐m) vadose zone downgradient from the injection wells, and extremely electrically resistive areas (greater than 10,000 ohm‐m) in the phreatic zone near the injection area. The sample data indicate that the electrically resistive anomalous zones contain moderate to high concentrations of undegraded dry‐cleaning compounds. Electrically conductive anomalous zones are interpreted to be areas of biological activity generated by the amendments injected into the subsurface based on the extreme conductivity values detected, the chemical composition (i.e., PCE degradates are present), and the dominant vadose‐zone location of the conductive zones. © 2012 Wiley Periodicals, Inc.     

Developments to a landfill processes model following its application to two landfill modelling challenges

The landfill model LDAT simulates the transport and bio-chemical behaviour of the solid, liquid and gas phases of waste contained in a landfill. LDAT was applied to the LMC1 and LMC2 landfill modelling challenges held in 2009 and 2011. These were blind modelling challenges with the model acting in a predictive mode based on limited early time sections of full datasets. The LMC1 challenge dataset was from a 0.34 m deep 0.48 m diameter laboratory test cell, and the LMC2 dataset was from a 55 m × 80 m 8 m deep landfill test cell which formed part of the Dutch sustainable landfill research programme at Landgraaf in the Netherlands. The paper describes developments in LDAT arising directly from the experience of responding to the two challenges, and discusses the model input and output data obtained from a calibration using the full datasets.The developments include the modularisation of the model into a set of linked sub-models, the strategy for converting conventional waste characteristics into model input parameters, the identification of flexible degradation pathways to control the CO₂:CH₄ ratio, and the application of a chemical equilibrium model that includes a stage in which the solid waste components dissolve into the leachate.     

Evaluating biotoxicity variations of landfill leachate as penetrating through the soil column

Recent studies of leachate-induced ecotoxicity have focused on crude samples, while little attention has been given to changes in biotoxicity resulting from the environmental behavior of landfill leachate. Therefore, we set up a soil column to simulate the underground penetration of leachate into the soil layer, define the rules of migration and transformation of leachate pollutants, and determine the variation in toxicity of landfill leachate during penetration. The results demonstrated that: (1) landfill leachate inhibited the growth and chlorophyll levels, elevated the levels of lipid peroxidation and protein oxidation, and stimulated the antioxidant enzyme activities of barley seedlings. The effects generally displayed a peak value at 12–24 cm, slowly declined at 36–48 cm, and then rapidly decreased with penetrating distance in the column. (2) Statistical correlation analysis of the properties of leachate and the observed biotoxic effects revealed that COD, conductivity and heavy metals (esp. Ni, Mn, Cd) were positively correlated with variations in biotoxicity. (3) The microbial activity of outflowing leachate sampled from the 48 cm port was significantly higher than the activity from succedent ports, and the types of contaminants increased in the leachate outflowing from the same port, implying that microbial behaviors near the 48 cm port could be used to partially evaluate variations in the composition and biotoxicity of landfill leachate. Taken together, the above results illustrate the polluting characteristics of landfill leachate when penetrating a soil column and provide guidance for pollution control and risk assessment of landfill leachate.     

Sustainable sanitary landfills for neglected small cities in developing countries: The semi-mechanized trench method from Villanueva,Honduras

Open dumping is the most common practice for the disposal of urban solid wastes in the least developed regions of Africa, Asia and Latin America. Sanitary landfill design and operation has traditionally focused on large cities, but cities with fewer than 50,000 in population can comprise from 6% to 45% of a given country’s total population. These thousands of small cities cannot afford to operate a sanitary landfill in the way it is proposed for large cities, where heavy equipment is used to spread and compact the waste in daily cells, and then to excavate, transport and apply daily cover, and leachate is managed with collection and treatment systems. This paper presents an alternative approach for small cities, known as the semi-mechanized trench method, which was developed in Villanueva, Honduras. In the semi-mechanized trench method a hydraulic excavator is used for 1–3 days to dig a trench that will last at least a month before it is filled with waste. Trucks can easily unload their wastes into the trench, and the wastes compact naturally due to semi-aerobic biodegradation, after which the trenches are refilled and covered. The exposed surface area is minimal since only the top surface of the wastes is exposed, the remainder being covered by the sides and bottom of the trench. The surplus material from trench excavation can be valorized for use as engineering fill onsite or off. The landfill in Villanueva has operated for 15 years, using a total land area of approximately 11 ha for a population that grew from 23,000 to 48,000, with a land requirement of 0.2 m²/person year, a cover to waste ratio of 0.2, and an estimated soil surplus of 298,000 m³ that is valorized and used onsite. The landfill has been operated solely by the municipality with an operational cost in 2010 estimated at US$4.60 per ton. A modified water balance analysis at Villanueva shows negligible leachate generation from covered trenches and 700 m³/yr (60 m³/ha yr) from the two open trenches required for daily operation. If the site were an open dump, however, leachate generation is estimated to be 3900 m³/ha yr and contaminated runoff 5000 m³/ha yr. A simple model used to estimate dilution of generated leachate based on groundwater flow data and aquifer stratigraphy suggests that the leachate will be diluted by a factor of 0.01 in the aquifer. Leachate contaminants will not accumulate because the aquifer discharges to the Ulua River 2 km south of the landfill. While not suitable for all sites, the Villanueva method nevertheless serves as an excellent example of how a small city landfill with natural compaction of waste and attenuation of leachate can be sustainably operated.     

Distributional Patterns of Arsenic Concentrations in Contaminant Plumes Offer Clues to the Source of Arsenic in Groundwater at Landfills

The distributional pattern of dissolved arsenic concentrations from landfill plumes can provide clues to the source of arsenic contamination. Under simple idealized conditions, arsenic concentrations along flow paths in aquifers proximal to a landfill will decrease under anthropogenic sources but potentially increase under in situ sources. This paper presents several conceptual distributional patterns of arsenic in groundwater based on the arsenic source under idealized conditions. An example of advanced subsurface mapping of dissolved arsenic with geophysical surveys, chemical monitoring, and redox fingerprinting is presented for a landfill site in New Hampshire with a complex flow pattern. Tools to assist in the mapping of arsenic in groundwater ultimately provide information on the source of contamination. Once an understanding of the arsenic contamination is achieved, appropriate remedial strategies can then be formulated. © 2013 Wiley Periodicals, Inc.*     

Spatial variability of nitrous oxide and methane emissions from an MBT landfill in operation: Strong N2O hotspots at the working face

Mechanical biological treatment (MBT) is an effective technique, which removes organic carbon from municipal solid waste (MSW) prior to deposition. Thereby, methane (CH₄) production in the landfill is strongly mitigated. However, direct measurements of greenhouse gas emissions from full-scale MBT landfills have not been conducted so far. Thus, CH₄ and nitrous oxide (N₂O) emissions from a German MBT landfill in operation as well as their concentrations in the landfill gas (LFG) were measured. High N₂O emissions of 20–200 g CO₂ eq. m^?2 h^?1 magnitude (up to 428 mg N m^?2 h^?1) were observed within 20 m of the working face. CH₄ emissions were highest at the landfill zone located at a distance of 30–40 m from the working face, where they reached about 10 g CO₂ eq. m^?2 h^?1. The MBT material in this area has been deposited several weeks earlier. Maximum LFG concentration for N₂O was 24.000 ppmv in material below the emission hotspot. At a depth of 50 cm from the landfill surface a strong negative correlation between N₂O and CH₄ concentrations was observed. From this and from the distribution pattern of extractable ammonium, nitrite, and nitrate it has been concluded that strong N₂O production is associated with nitrification activity and the occurrence of nitrite and nitrate, which is initiated by oxygen input during waste deposition. Therefore, CH₄ mitigation measures, which often employ aeration, could result in a net increase of GHG emissions due to increased N₂O emissions, especially at MBT landfills.     

Anionic Methyl Orange Removal from Aqueous Solutions by Activated Carbon Reinforced Conducting Polyaniline as Adsorbent: Synthesis,Characterization, Adsorption Behavior,Regeneration and Kinetics Study

This work investigated the elimination of Methyl Orange (MO) using a new adsorbent prepared from Activated Carbon (AC) with polyaniline reinforced by a simple oxidation chemical method. The prepared materials were characterized using XRD, TGA, FTIR and nitrogen adsorption isotherms. Furthermore, PANI@CA highest specific surface area values (near 332 m² g^?1) and total mesoporous volume (near 0.038 cm³ g^?1) displayed the better MO removal capacity (192.52 mg g^?1 at 298 K and pH 6.0), which is outstandingly higher than that of PANI (46.82 mg g^?1). Besides, the process’s adsorption, kinetics, and isothermal analysis were examined using various variables such as pH, MO concentration and contact time. To pretend the adsorption kinetics, various kinetics models, the pseudo first- and pseudo second- orders, were exercised to the experimental results. The kinetic analysis revealed that the pseudo second order rate law performed better than the pseudo first order rate law in promoting the formation of the chemisorption phase. In the case of isothermal studies, an analysis of measured correlation coefficient (R²) values showed that the Langmuir model was a better match to experimental results than the Freundlich model. By regeneration experiments after five cycles, acceptable results were observed.

     

Field investigation of the quality of fresh and aged leachates from selected landfills receiving e-waste in an arid climate

The management of electronic waste (e-waste) is a serious problem worldwide and much of it is landfilled. A survey of four selected landfills in an arid region of South Australia was conducted to determine the proportion of e-waste in municipal waste and the properties of each landfill site. Leachate and groundwater samples were collected upgradient and downgradient of the landfills for analysis of polybrominated diphenyl ethers (PBDEs) and 14 metals and metalloids, including Al, As, Ba, Be, Cd, Co, Cr, Cu, Fe, Ni, Pb, Sb, V and Zn. Our data demonstrate that the selected landfills in South Australia continue to receive municipal waste containing in excess of 6%, or 25,000 tonnes per year, of e-waste. The leachates and groundwater collected from the landfills contained significantly elevated concentrations of Pb with the highest concentration in groundwater of 38 μg/l, almost four times higher than the Australian drinking water guideline of 10 μg/l. The presence of PBDEs was detected in both leachate and groundwater samples. Total PBDEs values of 2.13–59.75 ng/l in leachate samples were 10 times higher than in groundwater samples, which recorded a range of 0.41–6.53 ng/l at all sites. Moreover, the concentrations of metals and metalloids in sampled groundwater contained elevated levels of Al, As, Fe, Ni and Pb that exceeded Australian drinking water guideline values. For these reasons potential leaching of these contaminants is of concern and while difficult to attribute elevated contaminant levels to e-waste, we do not recommend continued disposal of e-waste in old landfills that were not originally designed to contain leachates. The survey also revealed temporal variation in the electrical conductivity and concentrations of As, Cd and Pb present in leachates of landfills in arid Mediterranean climates. These results are consistent with the marked variations in rainfall patterns observed for such climates. The solute concentration (EC and other ions including As, Cd and Pb) declines in the leachates during wet winter months (June to September), in contrast to tropical countries where such changes are observed during wet summer months.     

A steady-state approach for evaluating the impact of solute transport through composite liners on groundwater quality

New adaptations of analytical equations for predicting the impact of solute transport through composite landfill liners on groundwater quality for steady-state conditions are presented. Analytical equations are developed for evaluating average concentration and mass flow rate in an underlying aquifer resulting from diffusion of volatile organic compounds (VOCs) through intact composite liners and transport of inorganic constituents through defects in composite liners. The equations are applied to evaluate the effectiveness and equivalency of composite liners having either a 0.6 m-thick compacted soil liner or a 6.5 mm-thick geosynthetic clay liner (GCL) overlying an intermediate attenuation layer and an aquifer having horizontal flow. Example analyses for designing composite liners meeting particular performance criteria are also provided. The analytical equations are relatively simple to apply and can be used for preliminary design and analysis, to evaluate experimental results, and to possibly verify more complex numerical models for evaluating the impact of landfills on groundwater quality if consistency of the assumptions of the analytical equations and the more complex numerical models can be specified.     

Case study of landfill reclamation at a Florida landfill site

A landfill reclamation project was considered to recover landfill airspace and soil, reduce future groundwater impacts by removing the waste buried in the unlined area, and optimize airspace use at the site. A phased approach was utilized to evaluate the technical and economic feasibility of the reclamation project; based on the results of these evaluations, approximately 6.8 ha of the unlined cells were reclaimed. Approximately 371,000 in-place cubic meters of waste was mined from 6.8 ha in this project. Approximately 230,600 cubic meters of net airspace was recovered due to beneficial use of the recovered final cover soil and reclaimed soil as intermediate and daily cover soil, respectively, for the current landfill operations. This paper presents the researchers’ landfill reclamation project experience, including a summary of activities pertaining to reclamation operations, an estimation of reclamation rates achieved during the project, project costs and benefits, and estimated composition of the reclaimed materials.     

Size fractionation of organic matter and heavy metals in raw and treated leachate

This study characterized the organic matter and heavy metals in the leachate from two typical municipal solid waste (MSW) sanitary landfills in China, the recently established (3-year-old) Liulitun landfill and the mature (11-year-old) Beishenshu landfill, using a size fractionation procedure. The organic matter of all raw and treated leachate samples primarily existed in a truly-dissolved fraction with an apparent molecular weight (AMW) of <1 kDa, and its percentage decreased with an increase in overall AMW. The leachate from the newer landfill had a higher percentage of truly-dissolved organic matter. After anaerobic treatment, this leachate had a similar size fraction of organic matter to that seen for the raw leachate of the mature landfill. Biochemical processes had different removal efficiencies for various types of AMW organic matter, and the concentration of moderate AMW organic matter appeared to increase throughout these processes. Most of the heavy metals existed in a colloidal fraction (AMW >1 kDa and particle size <0.45 μm). The behaviors of different species of heavy metals had large variations. The size fractions of heavy metal species were significantly affected by treatment processes and landfill age, except for Zn. The concentration ratio of heavy metals to organic matter was maximal in the colloidal fraction and showed an inverse change to that seen for organic matter concentration changes caused by biochemical processes. Consequently, the pollution levels of heavy metals were substantially increased by treatment processes, although their concentrations decreased.     

Organometals of tin, lead and mercury compounds in landfill gases and leachates from Bavaria, Germany

Organo-Sn, -Pb and -Hg compounds were monitored in gases and leachates of 11 municipal waste landfills and one hazardous waste landfill from Bavaria, Germany, with the objectives to estimate the methylation of Sn, Pb and Hg and to assess the risk of their release into the adjacent environment. In the gases, tetramethyl Sn predominated (>80% of total gaseous Sn) with concentrations up to 160mug Sn m(-3). Dimethyl-Hg and tetramethyl-Pb were only occasionally detected with concentrations up to 2.9 and 2.1mugm(-3) as Hg or Pb, respectively. In all leachates, trimethyl-Sn dominated with a maximum concentration of 2100ng Sn L(-1). No organo-Pb compounds were found, and monomethyl-Hg was detected in only one leachate. The concentrations of trimethyl-Sn were up to 100-fold higher in the condensate water than in leachates, and the concentrations of organo-Sn compounds were lower in the adjacent groundwater than in the corresponding leachates. The high abundance of methylated Sn species in the gases and leachates indicates Sn methylation, suggesting the landfill as a source for organo-Sn compounds. In comparison, methylation of Hg and Pb was of little importance, probably due to low Hg concentrations and low rates of Pb methylation in the landfill. The risks of organo-Sn compounds release to the adjacent air is low due to flaring of landfill gases. However, there is probable release of organo-Sn compounds, especially trimethyl-Sn, to the adjacent groundwater.     

Overview on LFG projects in China

Since the first landfill gas (LFG) power plant in China was built in 1998, by now more than 10 years have passed. In this period the LFG utilization process has progressed greatly in China. An overall review of the process is presented in this paper, which includes the background of policies, the information about the approval procedure of LFG projects, and the theoretical methods used to estimate the amount of LFG’s generation. Detailed analysis on the project practice, such as LFG collection techniques, LFG utilization condition in China, is made. According to statistic data, before the end of 2008, 26 LFG power projects have been built and put into operation with total power capacity around 56.8 MW, and 2.234 million tons of carbon dioxide equivalent abatement has been achieved annually by all of these LFG projects. The future of LFG industry in China is expected that there is still considerable developing space for LFG utilization in the near coming years, however after 2012, the progress speed may slow down because of some adverse aspects, such as available landfill resource becomes scarce, new laws implemented in China might exclude Chinese landfills from future CDM activities, etc.     

Microscopic synchrotron X-ray analysis of mercury waste in simulated landfill experiments

Mercury enters into the environment or waste streams because it is present as an impurity in natural minerals. Mercury must be appropriately managed as an hazardous waste. In this study, a waste layer of artificial mercury sulfide mixed with incinerator ash and sewage sludge compost in a simulated landfill experiment for 5 years was analyzed using microscopic synchrotron X-ray to obtain basic knowledge of mercury behavior in a landfill. Mapping by synchrotron X-ray revealed the distribution of mercury-containing particles in the waste layer. In most cases, the movement of mercury sulfide was not considered significant even within a microscopic range; however, water flows could enhance the movement of mercury sulfide particles. When disposing of mercury sulfide, “concentrated placement” or solidification, rather than mixing with other wastes, was more effective at preventing mercury leaching in lysimeters. The chemical form of mercury sulfide in each lysimeter was confirmed by X-ray absorption fine structure (XAFS) analysis, which showed that most of the mercury was present as metacinnabar and had not undergone any changes, indicating that it was extremely stable. The microscopic synchrotron X-ray analysis proved very useful for studying the behavior of mercury waste in a simulated landfill experiment.

     

Liquid balance monitoring inside conventional,Retrofit, and bio-reactor landfill cells

The Outer Loop landfill bioreactor (OLLB) in Louisville, KY, USA has been the site of a study to evaluate long-term bioreactor performance at a full-scale operational landfill. Three types of landfill units were studied including a conventional landfill (Control cell), a new landfill area that had an air addition and recirculation piping network installed as waste was being placed (As-Built cell), and a conventional landfill that was modified to allow for liquids recirculation (Retrofit cell). During the monitoring period, the Retrofit, Control, and As-Built cells received 48, 14, and 213 L Mg^?1 (liters of liquids per metric ton of waste), respectively. The leachate collection system yielded 60, 57 and 198 L Mg^?1 from the Retrofit, Control, and As-Built cells, respectively. The head on liner in all cells was below regulatory limits. In the Control and As-Built cells, leachate head on liner decreased once waste placement stopped. The measured moisture content of the waste samples was consistent with that calculated from the estimate of accumulated liquid by the liquid balance. Additionally, measurements on excavated solid waste samples revealed large spatial variability in waste moisture content. The degree of saturation in the Control cells decreased from 85% to 75%. The degree of saturation increased from 82% to 83% due to liquids addition in the Retrofit cells and decreased back to 80% once liquid addition stopped. In the As-Built cells, the degree of saturation increased from 87% to 97% during filling activities and then started to decrease soon after filling activities stopped to reach 92% at the end of the monitoring period. The measured leachate generation rates were used to estimate an in-place saturated hydraulic conductivity of the MSW in the range of 10^?8 to 10^?7 m s^?1 which is lower than previous reports. In the Control and Retrofit cells, the net loss in liquids, 43 and 12 L Mg^?1, respectively, was similar to the measured settlement of 15% and 5–8% strain, respectively (Abichou et al., 2013). The increase in net liquid volume in the As-Built cells indicates that the 37% (average) measured settlement strain in these cells cannot be due to consolidation as the waste mass did not lose any moisture but rather suggests that settlement was attributable to lubrication of waste particle contacts, softening of flexible porous materials, and additional biological degradation.