电解铝生产含氟工业烟气湿法吸收治理中试装置设计实现

本文通过对国内外近几年有关电解铝含氟化氢工业尾气净化处理大量的参考文献的分析研究及国内外电解铝生产企业在尾气治理方面的技术应用和尾气净化装置运行状况的调研,结合自己的专业特长和工程经验,建立一套有关电解铝含氟化氢尾气在处理、净化氟化氢方面的技术方案,设计制作一套湿法氟化氢吸收中试装置,从工艺方案优化设计、安全运行、设备设计及选材、自动控制、建立相关的副产物检测方法和后续产物的综合利用等方面进行了研究和探讨。     

再生有机胺法在硫酸尾气治理中的应用

根据国家《硫酸工业污染物排放标准》要求,金钼股份通过广泛调研和综合比选,最终采用再生有机胺脱硫技术对硫酸装置尾气进行二次吸收治理,并结合生产实际就工艺流程进行了改进优化,实施后取得了良好效果,最高脱硫效率可达99.76%,为国内现有硫酸装置尾气治理及新建冶炼烟气脱硫装置探索了一条示范途径。     

生产硫磺装置的危害因素及防护措施

<正>近年来,国内新建的以酸性气和N-甲基-二乙醇胺(MDEA)为原料生产硫磺的装置,大多采用二级转化Claus制硫工艺,尾气采用热焚烧炉处理,溶剂再生采用常规汽提再生技术。工艺系统主要包括硫磺回收、尾气处理、溶剂再生3部分。     

消除尾气氟的危害

江苏南通磷肥厂磷肥车间排入大气的尾气氟达6.000米3/小时,浓度为0.54克/米3,严重影响职工身体健康,污染环境。为消除尾气氛的危害,他们装置了一套回收生产氟硅酸钠的设备,回收率可达99.95%。 工艺是由化盐池、盐水泵、盐水计量槽、氟硅酸高位槽、氟硅酸钠结晶槽、电炉,气流干燥机、旋风分离器等组成。其化学反应原理是: 采用回收装置后,排入大气的尾气氟浓度下降到33.5毫米/米3,车间空气中的浓度大大低于国家卫生标准1毫克/米3,消除了氟气对职工身体健康的危害,还为国家节约了大量资金。消除尾气氟的危害…     

广钢金石分公司石灰竖窑尾气除尘探讨

回顾了广钢金石分公司竖窑石灰生产的尾气除尘方法，分析了其优缺点，同时分析了双膛窑尾气除尘的成功经验，提出了解决竖窑尾气除尘的措施。     

三甲酚生产及尾气制氢装置HAZOP分析

为积极推进对采用危险化工工艺的化工装置开展危险与可操作性分析（HAZOP分析）工作,进一步完善企业隐患排查治理常态化机制,某制药厂委托笔者所在单位对该厂三甲酚生产及尾气制氢装置进行了HAZOP分析。     

硫精砂制酸尾气达标排放及资源化回收利用

硫精砂制酸排出的尾气中SO2含量一般为0.2%~0.5%(体积分数,下同),目前国内普遍采用一转一吸或两转两吸流程来吸收硫酸尾气,使SO2质量浓度达到低于860 mg/m3的国家二级排放标准。但随着国家颁布新的《硫酸工业污染物排放标准》,要求现有硫酸企业SO2排放质量浓度必须于2013年10月1日前全部低于400mg/m3,因此必须对尾气进行进一步的处理。本文结合湖北新洋丰肥业股份有限公司和武汉中东化工有限公司硫酸生产的实际情况,总结了采取三段氨吸法处理硫酸尾气的技术改造和资源化回收利用。     

下坪渗滤液处理厂含氨尾气处理试验研究

对下坪垃圾填埋场含氨尾气的处理进行了研究.研究结果显示,采用硫酸吸收含氨尾气,吸收效率可达98%以上.吸收产生的硫酸铵产品符合<肥料、土壤调理剂-硫酸铵标准>(GB535-1995).     

丙烯氨氧化制丙烯腈反应器开车过程尾气燃爆危险性研究

丙烯直接氨氧化制丙烯腈工艺由于反应温度高,且反应器内的气相空间存在丙烯、丙烷、丙烯腈、乙腈、氧气、氮气等可燃性气体混合物,极易发生燃爆危险。为研究和评估该工艺装置反应器尾气的燃爆特性,采用11 L爆轰管测试在400℃、40 k Pa (G)工艺条件下,装置开车进料及反应过程中不同进料配比时反应器尾气组成的爆炸极限,并以此绘制爆炸极限三元相图,最终得到爆炸极限和极限氧体积分数。结果表明:反应器内可燃尾气的爆炸上限随氧气体积分数增加而升高,爆炸下限没有明显变化;在开车进料及反应过程中,反应器可燃尾气的极限氧体积分数LOC范围在8. 0%～8. 5%。因此,为避免反应器气相空间在开车过程中发生燃爆危险,需监测反应器内氧气体积分数,并设置氧体积分数报警值小于8. 0%。     

兴发集团新上磷化工废热回收装置一举两得

湖北宜昌兴发集团公司今年5月。投资180万元建成的国内第一套磷酸盐聚合炉尾气余热回收装置在该公司白沙河化工一厂六偏磷酸钠车间稳定运3个月，经过验收测算，不仅创经济效益50余万元,而且环保效益也十分明显。     

油浸变压器排油注氮装置在500kV变电站的设计与应用

在分析500kV变电站主变压器消防系统的现状,比较3类消防系统优缺点的基础上,详细论述了主变排油注氮装置的结构组成、工作原理、参数计算、控制系统设计以及需要注意的事项等,为下一步排油注氮装置的推广应用打下基础.     

HAZOP结合What-if方法在某延迟焦化装置除焦中的应用

为克服传统危险与可操作性（HAZOP）定性分析方法在复杂操作、间歇作业等过程中使用的局限性,提出在传统HAZOP定性分析方法的基础上结合What-if（故障假设）方法,对人的不安全行为和操作规程不完备所导致的风险后果分析作出补充。详细说明其技术原理、工作流程等使用细节,系统阐述该方法与传统HAZOP定性分析方法的区别,并在某延迟焦化装置的除焦操作的风险分析中应用。经分析,识别出在“给水-泡焦”节点,有“操作规程错误”场景2项,“操作规程不具体”场景1项,不存在“操作人员未按操作规程执行”场景。研究结果表明:本文方法有效且具有较好效果,可以广泛应用于操作规程/作业指导书审查、作业过程隐患排查等方面,帮助企业开展操作层面的风险识别与管理,提升企业的生产安全水平。     

潞安矿区煤层渗透率的各向异性特征实验研究

为了研究原位煤体渗透性的各向异性特征,以山西潞安常村矿3号煤层圆柱试样为对象,利用TCQT-Ⅲ型低渗煤层气相驱替增产试验装置,对煤样进行加载,并以氮气注入压力2.0 MPa的条件下,分析垂直层理和平行层理2个方向的煤体变形和渗透率变化特征。实验结果表明:煤样在加载过程中,平行和垂直层理煤样渗透率均随着有效应力的增大而减小,平行层理方向的渗透率始终大于垂直层理方向,应力加载初期渗透率急剧下降,最后逐渐趋于平缓;径向应变的增加量与渗透率呈正相关性,且平行层理相关性大于垂直层理;沿平行层理方向的裂隙度大于沿垂直层理方向,沿垂直层理方向的应变量大于沿平行层理方向;应变增加量均随有效应力的增加而逐渐减小。研究结果可为煤层井网布置及优化提供参考。     

Nighttime pedestrian fatalities: A comprehensive examination of infrastructure,user, vehicle,and situational factors

Introduction: Pedestrian fatalities in the United States increased 45.5% between 2009 and 2017. More than 85% of those additional pedestrian fatalities occurred at night. Method: We examine Fatality Analysis Reporting System (FARS) data for fatal pedestrian crashes that occurred in the dark between 2002 and 2017. Within-variable and before/after examinations of crashes in terms of infrastructure, user, vehicle, and situational characteristics are performed with one-way analysis of variance (ANOVA) and two-sample t-tests. We model changes in crash characteristic proportions between 2002–2009 and 2010–2017 using linear regressions and test for autocorrelation with Breusch-Godfrey tests. Results: The increase in fatal nighttime pedestrian crashes is most strongly correlated with infrastructure factors: non-intersection unmarked locations (saw 80.8% of additional fatalities); 40–45 mph roads (54.6%); five-lane roads (40.7%); urban (99.7%); and arterials (81.1%). In addition, SUVs were involved in 39.7% of additional fatalities, overrepresenting their share of the fleet. Increased pedestrian alcohol and drug involvement warrant further investigation. The age of pedestrians killed increased more (18.1%) than the national average (3.2%). Conclusions: By identifying factors related to the increase in nighttime pedestrian fatalities, this work constitutes a vital first step in making our streets safer for pedestrians. Practical Applications: More research is needed to understand the efficacy of different solutions, but this paper provides guidance for such future research. Engineering solutions such as road diets or traffic calming may be used to improve identified infrastructure issues by reducing vehicle speeds and road widths. Rethinking vehicle design, especially high front profiles, may improve vehicle issues. However, the problems giving rise to these pedestrian fatalities are likely a result of not only engineering issues but also interrelated social and political factors. Solutions may be correspondingly comprehensive, employing non-linear, systems-based approaches such as Safe Systems.     

Footedness and Mounting—Short Review and Two Case Studies

Footedness is a personal quality like handedness. Footedness may be associated with moving ability during mounting, dismounting, and jumping movements. Occupational accidents have occurred during movement at different working levels, during the use of access and exit systems, and during the mounting of vehicles. Aging can also affect accident risk and body laterality. For example, falling accidents on stairs are common among the elderly. One reason for accidents may be that the structure of the access system or stair system is unsuitable for individual moving patterns depending partly on body laterality. Footedness and the way the feet are used may be contradictory to the demands of the moving situation, especially during uncommon or rapid situations. This contradiction may trigger disturbance during moving. The aims of this pilot study were (a) to review the literature briefly and (b) to describe the use of the dominant and nondominant foot by farmers and the elderly when mounting a tractor and stairs, respectively. The study also gives ideas for future studies based on both (a) and (b).     

AHP与GA-SVM耦合模型在滑坡预警中的应用*

为了减少滑坡造成的损失,提高滑坡预测的准确性,通过搭建灾害模拟平台获得滑坡的实验数据,在获得多组模拟实验数据后,分析各变量的特性。首先,通过层次分析(Analytic Hierarchy Process,AHP)算法,对滑坡进行危险度划分;然后,通过支持向量机(Support Vector Machine,SVM)建立模型,遗传算法(Genetic Algorithm,GA)再优化SVM参数,提出1种层次分析法与GA-SVM相耦合的模型。研究结果表明:AHP方法划分后的数据,通过GA与SVM结合建立的模型精度较好,实验预测结果与实际结果较为吻合,与单一SVM相比,精度更高,结果更好,更加适用于多变量的复杂非线性滑坡预警。     

Debunking the false dichotomy of leadership idealism and pragmatism: Critical evaluation and support of newer genre leadership theories

Leadership theories have shifted over the last few decades from a focus on managerial functions and economic leader–follower exchanges toward greater focus on the interpersonal dynamics occurring within the leadership process. Theories such as transformational, ethical, authentic, and other “newer genre” theories were created to address neglected topics such as leader vision and inspirational messages, transparency, emotional effects, morality, individualized attention, and intellectual stimulation. Critiques of these theories, however, have been raised. In this paper, we address five of those critiques and argue for the validity and practical effectiveness of the new genre theories. Further, we describe how newer genre leadership research should be viewed as a performative epistemology, entailing a process of co‐creation involving scholars and practitioners. Finally, from this view, we provide general ideas for leader development. Copyright © 2014 John Wiley & Sons, Ltd.     

Occupational Safety and Health in Finland

In Finland, occupational safety is the responsibility of the employer, while the occupational safety and health laws are enforced by the Labour Inspection Service, an organization of the state. The Labour Inspection is divided in 11 administrative districts, and it employs 360 professionals. They are mandated to carry out site visits without prearranged appointments to inspect safe work situations, working hours, construction safety, or any aspect of accident risks. The inspectors are also mandated to verify the existence of sufficient occupational health services as prescribed by the Occupational Health Services Act for all employees. The occupational health services are typically provided by enterprise-owned medical departments, by mutually owned health care centers, by private practitioners, or by municipal health care centers. The latter are required by law to provide all services as prescribed by the legislation to anyone who comes to the facility. This situation is prevalent in the countryside, where there are very few private caregiving centers. Declaring occupational accidents and disease cases is mandatory, and the Inspection districts examine all accidents to establish causes and consequences, and to initiate prosecution in case of criminal negligence. Labour Inspection Districts are also notified of the new occupational disease cases as they are declared to insurance companies. Insurance for occupational disease, accidents, and death is an obligation of the employer, although they can choose the insurance company. The medical confidentiality between the workers and their occupational health care providers is very strict. Official statistics are maintained by the state Statistics Finland organization, and they may be used, for example, for research purposes by scientific institutes like the Finnish Institute of Occupational Health. Construction industry accounts for 25% of all fatal accidents (120 cases per 1 million working hours), followed by mechanical, wood, metal, machinery, and pulp and paper industry (10% each of fatal accidents) with rates ranging from 100–160 cases per 1 million working hours. There are some 5,000 occupational disease cases per year (rate 22/10,000 employed). The major disease categories include repetitive strain injuries (1,300 cases), respiratory allergies (600 cases), occupational skin diseases (1,000 cases), and 900 cases of noise-caused hearing loss. In 1998, 589 cases of asbestos-related diseases were reported.     

森林地表火蔓延模拟方法及其计算机实现

进行了森林火蔓延的研究,对传统的经验公式和模型进行改进,明显发现改进的模型有更好的结果,用计算机巧妙准确地实现了模拟模型,在风力不是特别大,地形变化不是特别剧烈时,该模型有较高精度;并结合火蔓延的主要因素（气象因子、气候、地形等）,进行系统分析,写出算地,编制实现地表火蔓延的预测预报计算机系统软件。这对于有效的组织扑救、减少火灾损失、计算森林火灾的损失评估有重要意义。     

公路隧道火灾逃生疏散研究

以苍岭隧道为背景,首先采用经验计算理论和计算软件building EXODUS相结合的方式,从被困人员的安全疏散时间、高温烟气的影响、隧道横通道的利用率以及人员的疏散行为特性进行了研究。结果表明:中小规模火灾情况下的安全疏散时间控制在8 min之内,高温烟气影响不大,但横通道的利用率不平均,且人员疏散路线相对集中。然后对存在的逃生疏散问题提出针对性建议以及其他相关建议,旨在为更大程度降低事故的严重性和经济财产损失。