Determination of solvents permeating through chemical protective clothing with a microsensor array

The performance of a novel prototype instrument in determining solvents and solvent mixtures permeating through samples of chemical protective clothing (CPC) materials was evaluated. The instrument contains a mini-preconcentrator and an array of three polymer-coated surface-acoustic-wave (SAW) microsensors whose collective response patterns are used to discriminate among multiple permeants. Permeation tests were performed with a 2.54 cm diameter test cell in an open-loop configuration on samples of common glove materials challenged with four individual solvents, three binary mixtures, and two ternary mixtures. Breakthrough times, defined as the times required for the permeation rate to reach a value of 1 microg cm(-2) min(-1), determined by the instrument were within 3 min of those determined in parallel by manual sampling and gas chromatographic analysis. Permeating solvents were recognized (identified) from their response patterns in 59 out of 64 measurements (92%) and their vapor concentrations were quantified to an accuracy of +/- 31% (typically +/- 10%). These results demonstrate the potential for such instrumentation to provide semi-automated field or bench-top screening of CPC permeation resistance.     

便携式GC-MS法快速测定固定污染源废气中的VOCs

采用便携式GC-MS法快速测定固定污染源废气中VOCs,32种VOCs在2×10~(-7)~1×10~(-6)范围内线性良好,方法检出限为2×10~(-9)~1×10~(-8),标准气体样品6次测定结果的RSD为1.9%~19.1%,环境空气样品的加标回收率为66.2%~116%。在实际现场监测固定污染源中VOCs时,使用速查(Survey)功能可初步判断样品浓度,确定稀释倍数。比对试验结果表明,气袋和玻璃注射器采样法对VOCs测定结果无显著性差异。     

Implementing infrared determination of quartz particulates on novel filters for a prototype dust monitor

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized filter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM). Standard fiberglass TEOM filters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel filter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon fiber candidate filters left minimal residual ash and produced no significant spectral interference. Avoiding titanium dioxide in all filter materials proved to be a key requirement. Fine quartz particulates were collected on prototype filters in a Marple chamber, either open-faced or through PDMs during test runs. The filters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to filter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in filter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM filters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7-10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM filters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.     

The determination of carbonyl compounds in air using a robotic sampling preparation system integrated to a gas chromatograph with a nitrogen-phosphorus detector

A totally automated solid phase extraction gas chromatography procedure was developed for the sampling and analysis of carbonyl compounds in air. In this system, two PrepStation modules were used, one for the preparation and elution of 2,4-dinitrophenylhydrazine silica cartridges, and the other for air sampling. The sample collected by the sampling module was eluted to an autosampler vial in the PrepStation module and then transferred to the gas chromatograph for analysis via a robotic arm. The sampling module was modified to enable air sampling via an external pump. A typical run by this technique required 142 min, 100 min for air sampling and 42 min for the other operations, including a GC analysis time of 25 min. Recoveries of at least 85% were obtained for all compounds studied. The detection limits for formaldehyde, acetaldehyde and acetone were 2.2, 2.7 and 2.2 ppbv, respectively. All operations, including the conditioning of the cartridges, were performed without any intervention from the analyst.     

连续流动分析快速测定环境水样中的硫化物

用新型的连续流动分析对环境水样中的硫化物进行分析测定。与传统的分析方法相比,该方法具有快速、灵敏度高、检出限低的特点。该方法的分析频率可达60次/小时,检测下限为0.006mg/L,大大提高了实验室自动化程度。     

光离子化检测器便携式气相色谱仪快速测定空气中苯系物

本文研究了使用光离子化检测器便携式气相色谱仪,直接测定空气中ｍｇ／ｍ３级苯系物（苯、甲苯、乙苯、邻、间、对位的二甲苯及异丙苯）的快速分析方法。方法的线性范围为０～１００ｍｇ／ｍ３,相关系数均在０．９９９以上,方法的变异系数分别为２．９～１２．５％（５ｍｇ／ｍ３）,３．４～７．９％（３０ｍｇ／ｍ３）,方法最低检测限达０．２～１．０ｍｇ／ｍ３。     

Chamber evaluation of a portable GC with tunable retention and microsensor-array detection for indoor air quality monitoring

The evaluation of a novel prototype instrument designed for on-site determinations of VOC mixtures found in indoor working environments is described. The instrument contains a miniature multi-stage preconcentrator, a dual-column separation module with pressure-tunable retention capabilities, and an integrated array of three polymer-coated surface acoustic wave sensors. It was challenged with dynamic test-atmospheres of a set of 15 common indoor air contaminants at parts-per-billion concentrations within a stainless-steel chamber under a range of conditions. Vapours were reliably identified at a known level of confidence by combining column retention times with sensor-array response patterns and applying a multivariate statistical test of pattern fidelity for the chromatographically resolved vapours. Estimates of vapour concentrations fell within 7% on average of those determined by EPA Method TO-17, and limits of detection ranged from 0.2 to 28 ppb at 25 degrees C for 1 L samples collected and analyzed in <12 min. No significant humidity effects were observed (0-90% RH). Increasing the chamber temperature from 25 to 30 degrees C reduced the retention times of the more volatile analytes which, in turn, demanded alterations in the scheduling of column-junction-point pressure (flow) modulations performed during the analysis. Reductions in sensor sensitivities with increasing temperature were predictable and similar among the sensors in the array such that most response patterns were not altered significantly. Short-term fluctuations in concentration were accurately tracked by the instrument. Results indicate that this type of instrument could provide routine, semi-autonomous, near-real-time, multi-vapour monitoring in support of efforts to assess air quality in office environments.     

Characterization of dissolved organic carbon at low levels in environmental waters by microfluidic-chip-based capillary gel electrophoresis with a laser-induced fluorescence detector

A microfluidic analytical system for characterization of dissolved organic carbon (DOC) in environmental waters, based on a capillary gel electrophoresis (CGE) device with a laser-induced fluorescence (LEF) detector, was developed. The applied voltage and the running buffer were investigated to control the simple floating injection and CGE separation for convenient cross-type microchips made from polymethylmethacylate. We obtained reproducible peaks for standard organic solutions and the determination time is less than 70 s. The values of the relative standard deviation (RSD) were 0.17–2.01% for repetitive injection (n?=?12). We demonstrated high-throughput characterization of DOC in environmental water from the Biwa Lake and the Hino River using microfluidic chip and determined that the content of DOC in the Biwa Lake changed with the seasons.     

The biological behaviour and bioavailability of aluminium in man, with special reference to studies employing aluminium-26 as a tracer: review and study update

Until 1990 biokinetic studies of aluminium metabolism and biokinetics in man and other animals had been substantially inhibited by analytical and practical difficulties. Of these, the most important are the difficulties in differentiating between administered aluminium and endogenous aluminium-especially in body fluids and excreta and the problems associated with the contamination of samples with environmental aluminium. As a consequence of these it was not possible to detect small, residual body burdens of the metal following experimental administrations. Consequently, many believed aluminium to be quantitatively excreted within a short time of uptake in all, but renal-failure patients. Nevertheless, residual aluminium deposits in a number of different organs and tissues had been detected in normal subjects using a variety of techniques, including histochemical staining methods. In order to understand the origins and kinetics of such residual aluminium deposits new approaches were required. One approach taken was to employ the radioisotope (67)Ga as a surrogate, but this approach has been shown to be flawed-a consequence of the different biological behaviours of aluminium and gallium. A second arose from the availability, in about 1990, of both (26)Al-a rare and expensive isotope of aluminium-and accelerator mass spectrometry for the ultra-trace detection of this isotope. Using these techniques the basic features of aluminium biokinetics and bioavailability have been unravelled. It is now clear that some aluminium is retained in the body-most probably within the skeleton, and that some deposits in the brain. However, most aluminium that enters the blood is excreted in urine within a few days or weeks and the gastrointestinal tract provides an effective barrier to aluminium uptake. Aspects of the biokinetics and bioavailability of aluminium are described below.     

On-site simultaneous determination of anions and cations in drainage water using a flow injection-capillary electrophoresis system with contactless conductivity detection

Drainage water diverted from a farm pasture, which was heavily loaded with manure, was monitored during a rain event. Concurrent anion and cation determinations at intervals of 10 min could be achieved with a new capillary electrophoresis system employing dual injection at opposite ends of the separation capillary. The flow injection approach enabled automation of the sampling process. Interruption of the separation voltage was not necessary. Contactless conductivity detection with an electrolyte solution optimized for the purpose allowed the facile simultaneous detection of the inorganic ions Cl(-), NO(3)(-), SO(4)(2-), HPO(4)(2-), NO(2)(-), NH(4)(+), K(+), Ca(2+), Na(+) and Mg(2+) and the acquisition of temporal concentration profiles of these species. The detection limits achieved were between 20 and 200 [micro sign]g l(-1) for all ions and the repeatability of peak areas and peak heights was better than 1%. The quantitative results were verified by analysing individual samples later in the laboratory with photometry and ion chromatography and the average deviations were found to be between 4 and 12%. This contribution presents a further step in the development of capillary electrophoresis towards a fully automated, low maintenance field method.     

Development of a personal monitoring method for nitrogen dioxide and sulfur dioxide with Sep-Pak C18 cartridge sampling and ion chromatographic determination

Personal monitoring methods for the determination of hourly integrated concentrations of NO2 and SO2 in ambient air have been developed. Triethanolamine (TEA)-impregnated C18 Sep-Pak cartridges were used to collect NO2 and SO2 simultaneously. After sampling, NO2 and SO2 as their nitrite, nitrate, sulfite and sulfate analogues were stripped from the cartridges with a solution of 5% methanol in distilled, deionized water (DDW) and then determined by ion chromatography. Laboratory tests were conducted to evaluate the sampling rate, collection and recovery efficiencies, breakthrough volumes, absorption capacity, interference and sample stability on the cartridge during storage. NO2 and SO2 detection limits of 0.3 and 0.4 ppb respectively for 1 h samples were obtained. Recoveries for both NO2 and SO2 exceeded 85%.     

2-Nitroso-1-naphthol as a selective reagent for preconcentration of cobalt by vortex assisted combined with solidification of organic droplet and its determination by flame atomic absorption spectrometry

Highly rapid and selective vortex-assisted liquid–liquid microextraction based on solidification of organic drop has been used for determination of cobalt ion. 2-Nitroso-1-naphthol (2N1N) was used as a selective complexing agent to form stable cobalt–2N1N complex which can be extracted with 1-undecanol at a short time by the assistance of vortex agitator system followed by its determination using flame atomic absorption spectrometry. In vortex assisted, vigorous vortex stream as well as the vibrant effect of vortex system cause very fine droplets of extraction solvent to be produced and extraction occurred at a short time. Some parameters influencing the extraction process such as pH of samples, concentration of 2-nitroso-1-naphthol, extraction solvent volume, extraction time, ionic strength and surfactant addition, as well as interferences were evaluated in detail and optimum conditions were selected. At the optimum conditions, the calibration curve was linear in the range of 15 to 400 μg L^?1 of cobalt ions. The relative standard deviation based on ten replicate analysis of sample solution containing 50 μg L^?1 of cobalt was 3.4 %. The detection limit (calculated as the concentration equivalent to three times of the standard deviation of the blank divided by the slope of the calibration curve after preconcentration) was 5.4 μg L^?1. The accuracy of the proposed method was successfully evaluated by the analysis of certified reference materials. This selective and highly rapid method was used for determination of cobalt ions in different water samples.