Energy implications of mechanical and mechanical–biological treatment compared to direct waste-to-energy

Primary energy savings potential is used to compare five residual municipal solid waste treatment systems, including configurations with mechanical (MT) and mechanical–biological (MBT) pre-treatment, which produce waste-derived fuels (RDF and SRF), biogas and/or recover additional materials for recycling, alongside a system based on conventional mass burn waste-to-energy and ash treatment. To examine the magnitude of potential savings we consider two energy efficiency levels (state-of-the-art and best available technology), the inclusion/exclusion of heat recovery (CHP vs. PP) and three different background end-use energy production systems (coal condensing electricity and natural gas heat, Nordic electricity mix and natural gas heat, and coal CHP energy quality allocation).The systems achieved net primary energy savings in a range between 34 and 140 MJ_primary/100 MJ_{input waste}, in the different scenario settings. The energy footprint of transportation needs, pre-treatment and reprocessing of recyclable materials was 3–9.5%, 1–18% and 1–8% respectively, relative to total energy savings. Mass combustion WtE achieved the highest savings in scenarios with CHP production, nonetheless, MBT-based systems had similarly high performance if SRF streams were co-combusted with coal. When RDF and SRF was only used in dedicated WtE plants, MBT-based systems totalled lower savings due to inherent system losses and additional energy costs. In scenarios without heat recovery, the biodrying MBS-based system achieved the highest savings, on the condition of SRF co-combustion. As a sensitivity scenario, alternative utilisation of SRF in cement kilns was modelled. It supported similar or higher net savings for all pre-treatment systems compared to mass combustion WtE, except when WtE CHP was possible in the first two background energy scenarios. Recovery of plastics for recycling before energy recovery increased net energy savings in most scenario variations, over those of full stream combustion. Sensitivity to assumptions regarding virgin plastic substitution was tested and was found to mostly favour plastic recovery.     

Production,quality and quality assurance of Refuse Derived Fuels (RDFs)

This contribution describes characterization, classification, production, application and quality assurance of Refuse Derived Fuels (RDFs) that are increasingly used in a wide range of co-incineration plants. It is shown in this paper, that the fuel-parameter, i.e. net calorific value [MJ/kg_OS], particle size d₉₀ or d₉₅ [mm], impurities [w%], chlorine content [w%], sulfur content [w%], fluorine content [w%], ash content [w%], moisture [w%] and heavy metals content [mg/kg_DM], can be preferentially used for the classification of different types of RDF applied for co-incineration and substitution of fossil-fuel in different industial sectors. Describing the external production of RDF by processing and confectioning of wastes as well as internal processing of waste at the incineration plant, a case study is reported on the application of RDF made out of different household waste fractions in a 120,000 t/yr Waste to Energy (WtE) circulating fluidized bed (CFB) incinerator. For that purpose, delivered wastes, as well as incinerator feedstock material (i.e. after internal waste processing) are extensively investigated. Starting with elaboration of sampling plan in accordance with the relevant guidelines and standards, waste from different suppliers was sampled. Moreover, manual sorting analyses and chemical analyses were carried out. Finally, results of investigations are presented and discussed in the paper.     

Analysis of potential RDF resources from solid waste and their energy values in the largest industrial city of Korea

The production potential of refuse derived fuel (RDF) in the largest industrial city of Korea is discussed. The purpose of this study is to evaluate the energy potential of the RDF obtained from utilizing combustible solid waste as a fuel resource. The total amount of generated solid waste in the industrial city was more than 3.3 million tonnes, which is equivalent to 3.0 tonnes per capita in a single year. The highest amount of solid waste was generated in the city district with the largest population and the biggest petrochemical industrial complex (IC) in Korea. Industrial waste accounted for 89% of the total amount of the solid waste in the city. Potential RDF resources based on combustible solid wastes including wastepaper, wood, rubber, plastic, synthetic resins and industrial sludge were identified. The amount of combustible solid waste that can be used to produce RDF was 635,552 tonnes/yr, consisting of three types of RDF: 116,083 tonnes/yr of RDF-MS (RDF from municipal solid waste); 146,621 tonnes/yr of RDF-IMC (RDF from industrial, municipal and construction wastes); and 372,848 tonnes/yr of RDF-IS (RDF from industrial sludge). The total obtainable energy value from the RDF resources in the industrial city was more than 2,240,000 × 10⁶ kcal/yr, with the following proportions: RDF-MS of 25.6%, RDF-IMC of 43.5%, and RDF-IS of 30.9%. If 50% or 100% of the RDF resources are utilized as fuel resources, the industrial city can save approximately 17.6% and 35.2%, respectively, of the current total disposal costs.     

Separation of fine binary mixtures under vibration in a gas-solid fluidized bed with dense medium.

The coke-slag mixture discharged from water-air generators not only causes a serious environmental problem, but also is a potential resource. In order to obtain a high economic return, separation of fine binary mixtures in a vibrating fluidized bed with dense media was experimentally investigated. The effects of volume ratio (mono-component volume to dense medium volume or binary mixture volume to dense medium volume), the fluidization velocity and vibration parameters on separation efficiency are discussed. The experimental results show that vibration can prevent the coalescence and growth of bubbles and improve fluidization properties of particles and the stability of bed density. The major factors associated with separating efficiency are discussed. Based on the experiments, the ratio of the volume of particles to bed volume and the vibration conditions are also reported. It was found that the separation efficiency for a fine coke-slag mixture was greater than 70% and close to 80% under optimal conditions.     

Perspectives and limits for cement kilns as a destination for RDF

RDF, the high calorific value fraction of MSW obtained by conventional separation systems, can be employed in technological plants (mainly cement kilns) in order to obtain a useful energy recovery. It is interesting and important to evaluate this possibility within the general framework of waste-to-energy solutions. The solution must be assessed on the basis of different aspects, namely: technological features and clinker characteristics; local atmospheric pollution; the effects of RDF used in cement kilns on the generation of greenhouse gases; the economics of conventional solid fuels substitution and planning perspectives, from the point of view of the destination of RDF and optimal cement kiln policy. The different experiences of this issue throughout Europe are reviewed, and some applications within Italy are also been considered. The main findings of the study are that the use of RDF in cement kilns instead of coal or coke offers environmental benefits in terms of greenhouse gases, while the formation of conventional gaseous pollutants is not a critical aspect. Indeed, the generation of nitrogen oxides can probably be lower because of lower flame temperatures or lower air excess. The presence of chlorinated micro-pollutants is not influenced by the presence of RDF in fuel, whereas depending on the quality of the RDF, some problems could arise compared to the substituted fuel as far as heavy metals are concerned, chiefly the more volatile ones.     

Perspectives for pilot scale study of RDF in Istanbul,Turkey

Municipal solid waste (MSW) is one of the most important environmental problems arising from rapid urbanization and industrialization. The use of alternative fuels in rotary kilns of cement plants is very important for reducing cost, saving fossil fuels and also eliminating waste materials, accumulated during production or after using these materials. Cement industries has an important potential for supplying preferable solutions to the waste management. Energy recovery from waste is also important for the reduction of CO₂ emissions.This paper presents an investigation of the development of refuse derived fuel (RDF) materials from non-recycling wastes and the determination of its potential use as an alternative fuel in cement production in Istanbul, Turkey. RDF produced from MSW was analyzed and its effects on cement production process were examined. For this purpose, the produced RDF was mixed with the main fuel (LPG) in ratios of 0%, 5%, 10%, 15% and 20%. Then chemical and mineralogical analyses of the produced clinker were carried out. It is believed that successful results of this study will be a good example for municipalities and cement industries in order to achieve both economic and environmental benefits.     

An integrated appraisal of energy recovery options in the United Kingdom using solid recovered fuel derived from municipal solid waste

This paper reports an integrated appraisal of options for utilising solid recovered fuels (SRF) (derived from municipal solid waste, MSW) in energy intensive industries within the United Kingdom (UK). Four potential co-combustion scenarios have been identified following discussions with industry stakeholders. These scenarios have been evaluated using (a) an existing energy and mass flow framework model, (b) a semi-quantitative risk analysis, (c) an environmental assessment and (d) a financial assessment. A summary of results from these evaluations for the four different scenarios is presented. For the given ranges of assumptions; SRF co-combustion with coal in cement kilns was found to be the optimal scenario followed by co-combustion of SRF in coal-fired power plants. The biogenic fraction in SRF (ca. 70%) reduces greenhouse gas (GHG) emissions significantly (～2500 g CO₂ eqvt./kg DS SRF in co-fired cement kilns and ～1500 g CO₂ eqvt./kg DS SRF in co-fired power plants). Potential reductions in electricity or heat production occurred through using a lower calorific value (CV) fuel. This could be compensated for by savings in fuel costs (from SRF having a gate fee) and grants aimed at reducing GHG emission to encourage the use of fuels with high biomass fractions. Total revenues generated from coal-fired power plants appear to be the highest (£95/t SRF) from the four scenarios. However overall, cement kilns appear to be the best option due to the low technological risks, environmental emissions and fuel cost. Additionally, cement kiln operators have good experience of handling waste derived fuels. The scenarios involving co-combustion of SRF with MSW and biomass were less favourable due to higher environmental risks and technical issues.     

Study of hydrodynamic characteristics in a circulating fluidized bed gasifier for plastic waste by computational fluid dynamics modeling and simulation

For designing an efficient circulating fluidized bed reactor, understanding the complex hydrodynamic characteristics in the reactor is required. Hence, in the present study, the modeling and simulation of the circulating fluidized bed gasifier using plastic waste were carried out with Eulerian-Granular approach. Several cases were investigated as changing superficial gas velocities or sizes of plastic waste particle. Firstly, cases were examined with four different velocities when the particle diameter is 1 mm. At the gas velocity of 6 or 8 m/s, gas volume fraction is more than 95 % throughout the reactor and particle velocity has positive value overall. Therefore, a circulating fluidized bed seems to be formed in both cases. Comparing those two cases, better solid mixing can be expected considering the mass fraction and solid velocity at the superficial gas velocity of 6 m/s. Thus this case was further studied for the effect of particle size. As the diameters of plastic waste particle are 1 or 3 mm, it is considered that a circulating fluidized bed is formed. And plastic waste and sand particles are well mixed throughout the reactor. However, the particle diameter increases over 3 mm then, it is very hard to maintain circulating fluidization condition.     

Evaluating the biogas potential of the dry fraction from pretreatment of food waste from households

At the waste handling company NSR, Helsingborg, Sweden, the food waste fraction of source separated municipal solid waste is pretreated to obtain a liquid fraction, which is used for biogas production, and a dry fraction, which is at present incinerated. This pretreatment and separation is performed to remove impurities, however also some of the organic material is removed. The possibility of realising the methane potential of the dry fraction through batch-wise dry anaerobic digestion was investigated. The anaerobic digestion technique used was a two-stage process consisting of a static leach bed reactor and a methane reactor. Treatment of the dry fraction alone and in a mixture with structural material was tested to investigate the effect on the porosity of the leach bed. A tracer experiment was carried out to investigate the liquid flow through the leach beds, and this method proved useful in demonstrating a more homogenous flow through the leach bed when structural material was added. Addition of structural material to the dry fraction was needed to achieve a functional digestion process. A methane yield of 98 m³/ton was obtained from the dry fraction mixed with structural material after 76 days of digestion. This was in the same range as obtained in the laboratory scale biochemical methane potential test, showing that it was possible to extract the organic content in the dry fraction in this type of dry digestion system for the production of methane.     

Thermal valorization of post-consumer film waste in a bubbling bed gasifier

The use of plastic bags and film packaging is very frequent in manifold sectors and film waste is usually present in different sources of municipal and industrial wastes. A significant part of it is not suitable for mechanical recycling but could be safely transformed into a valuable gas by means of thermal valorization. In this research, the gasification of film wastes has been experimentally investigated through experiments in a fluidized bed reactor of two reference polymers, polyethylene and polypropylene, and actual post-consumer film waste. After a complete experimental characterization of the three materials, several gasification experiments have been performed to analyze the influence of the fuel and of equivalence ratio on gas production and composition, on tar generation and on efficiency. The experiments prove that film waste and analogue polymer derived wastes can be successfully gasified in a fluidized bed reactor, yielding a gas with a higher heating value in a range from 3.6 to 5.6 MJ/m³ and cold gas efficiencies up to 60%.     

Innovative process routes for a high-quality concrete recycling

This study presents alternative methods for the processing of concrete waste. The mechanical stresses needed for the embrittlement of the mortar matrix and further selective crushing of concrete were generated by either electric impulses or microwaves heating. Tests were carried out on lab-made concrete samples representative of concrete waste from concrete mixer trucks and on concrete waste collected on a French demolition site. The results obtained so far show that both techniques can be used to weaken concrete samples and to enhance aggregate selective liberation (that is the production of cement paste-free aggregates) during crushing and grinding. Electric pulses treatment seems to appear more efficient, more robust and less energy consuming (1–3 kW h t^?1) than microwave treatment (10–40 kW h t^?1) but it can only be applied on samples in water leading to a major drawback for recycling aggregates or cement paste in the cement production process.     

Energy recovery from waste incineration: Assessing the importance of district heating networks

Municipal solid waste incineration contributes with 20% of the heat supplied to the more than 400 district heating networks in Denmark. In evaluation of the environmental consequences of this heat production, the typical approach has been to assume that other (fossil) fuels could be saved on a 1:1 basis (e.g. 1 GJ of waste heat delivered substitutes for 1 GJ of coal-based heat). This paper investigates consequences of waste-based heat substitution in two specific Danish district heating networks and the energy-associated interactions between the plants connected to these networks. Despite almost equal electricity and heat efficiencies at the waste incinerators connected to the two district heating networks, the energy and CO₂ accounts showed significantly different results: waste incineration in one network caused a CO₂ saving of 48 kg CO₂/GJ energy input while in the other network a load of 43 kg CO₂/GJ. This was caused mainly by differences in operation mode and fuel types of the other heat producing plants attached to the networks. The paper clearly indicates that simple evaluations of waste-to-energy efficiencies at the incinerator are insufficient for assessing the consequences of heat substitution in district heating network systems. The paper also shows that using national averages for heat substitution will not provide a correct answer: local conditions need to be addressed thoroughly otherwise we may fail to assess correctly the heat recovery from waste incineration.     

Life cycle impact assessment of various waste conversion technologies

Advanced thermal treatment technologies utilizing pyrolysis or gasification, as well as a combined approach, are introduced as sustainable methods to treat wastes in Singapore. Eight different technologies are evaluated: pyrolysis–gasification of MSW; pyrolysis of MSW; thermal cracking gasification of granulated MSW; combined pyrolysis, gasification and oxidation of MSW; steam gasification of wood; circulating fluidized bed (CFB) gasification of organic wastes; gasification of RDF; and the gasification of tyres.Life cycle assessment is carried out to determine the environmental impacts of the various waste conversion systems including global warming potential, acidification potential, terrestrial eutrophication and ozone photochemical formation. The normalization and weighting results, calculated according to Singapore national emission inventories, showed that the two highest impacts are from thermal cracking gasification of granulated MSW and the gasification of RDF; and the least are from the steam gasification of wood and the pyrolysis–gasification of MSW.A simplified life cycle cost comparison showed that the two most costs-effective waste conversion systems are the CFB gasification of organic waste and the combined pyrolysis, gasification and oxidation of MSW. The least favorable – highest environmental impact as well as highest costs – are the thermal cracking gasification of granulated MSW and the gasification of tyres.     

Medical waste generation in selected clinical facilities in Taiwan

This study investigated the type and amount of medical waste generated from small clinical facilities in Taiwan. We sampled 200 small medical establishments, with few or no patient beds, to survey the wastes generated and disposed. The surveyed medical facilities consisted of four groups including private clinics, medical laboratories, blood centers and public clinics. Private clinics providing surgical, dental, obstetrical, and dialysis services were included in this survey because they may generate higher amounts of infectious waste than other specialties. The overall mean general waste production rate was 3.97 kg/bed/day (or 0.075 kg/patient/day) at all the surveyed facilities, higher than that obtained from larger hospitals in Taiwan, which ranged from 2.41 to 3.26 kg/bed/day. The highest amount of infectious wastes generated among the four groups of facilities were from blood centers (3.14 kg/bed/day), followed by private clinics, medical laboratories and public clinics (1.91, 1.07, and 0.053 kg/bed/day, respectively). The overall average was 2.08 kg/bed/day. This study suggests that the waste generated at small medical facilities ranged widely.     

Batch separation of shredded bulky waste by gas-solid fluidized bed at laboratory scale

A gas-solid fluidized bed separator using various bed materials was used to separate shredded municipal bulky waste (SBW). Using 290 microm glass beads as the bed material, the apparent density of the fluidized bed was 1.5 g/cm(3) and the SBW could be separated into combustibles such as wood, paper and plastics and incombustibles such as metals and glass. The overall efficiency (Newton's efficiency) of the separation was calculated to be 0.93. In order to obtain high efficiency, the superficial velocity must be adjusted so that the fluidized bed is agitated moderately and at the same time there is no weak fluidized region. Using a mixture of particles of nylon shot and 68 microm glass beads, the apparent density of the fluidized mixture bed could be varied between 0.63 and 0.99 g/cm(3) by changing the mixing ratio of the two materials. In the case of a mixing ratio of 20% for glass beads, an apparent density of 0.65 g/cm(3) was produced, in which wood and paper components were recovered while plastics remained in the bed to give a final overall efficiency of 0.88.     

An innovative example of herb residues recycling by gasification in a fluidized bed

A utilization way of herb residues is designed to convert herb residues to gas fuel in industrial-scale by a circulating fluidized bed gasifier in this paper. The product gas is used in the production of Chinese medicine, and the heat of the flue gas from the boiler can be used in herb residues drying to realize the energy recycling and no herb residues discharge. The gasification characteristics of herb residues in the circulating fluidized bed of 300 kg/h were investigated for about 200 h. The results indicated that the gas composition and tar yield were affected by biomass flow rate, equivalence ratio (ER), moisture content and char circulating. The lower heating value of product gas was 4–5 MJ/m³ using herb residues as feedstock. When mean biomass flow rate was at 5.5 kg m^?2 s^?1 and ER at 0.35, the product gas reached a good condition with lower heating value of 4.89 MJ/m³ and cold gas efficiency of 62.36%. When the moisture content changed from 12.5% to 18.7%, the concentrations of H₂, CO and CO₂ changed from 4.66% to 6.92%, 11.23% to 10.15%, and 16.55% to 17.82% respectively, and the tar content in gas decreased from 15.1 g/m³ to 14.4 g/m³ when the moisture content increased from 12.5% to 15.4%. There are metal oxides in the ash of herb residues, especially CaO, MgO, K₂O, Al₂O₃, and Fe₂O₃ which have obvious function on tar catalytic decomposition. The ash that attaches to the char particles can decrease the tar yield and improve the quality of gas after returning to the gasifier.     

An investigation on pollutant emissions from co-firing of RDF and coal

Pollutant emissions from co-firing of refuse derived fuel (RDF) and coal were investigated in a vortexing fluidized bed combustor (VFBC). RDF-5 was made of common municipal solid waste (MSW). CaCO₃ was injected in the combustor to absorb HCl at 850 °C. The results show that NO_x and HCl emissions increase with RDF-5 co-firing ratio. The NO_x concentration in flue gas at the bottom of the combustor is higher than that at the top. However, the trend of HCl released is reverse compared with NO_x emissions. It was found that the HCl concentration decreases with increasing the molar ratio of Ca/Cl. However, the effect of CaCO₃ addition on HCl retention is not significant when the molar ratio of Ca/Cl is higher than 5. The chlorine content in fly ash increases obviously with the molar ratio of Ca/Cl. PCDD/Fs emissions decrease slightly with an addition of CaCO₃. In this study incomplete combustion is regarded as the main cause for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) formation.     

Investigation of the self-heating and spontaneous ignition of refuse-derived fuel (RDF) during storage

Refuse-derived fuel (RDF)—RDF-5 according to ASTM guidelines—derived from municipal solid waste and other waste materials, has been prepared as a fuel source for power plants in Japan. RDF has been known as a stable and safe solid-fuel. However, some spontaneous ignition incidents occurred during storage of RDF in certain facilities. In the present study, the storage conditions, which might induce the spontaneous ignition in RDF samples, was investigated to understand and prevent this phenomenon. When the initial temperature of RDF sample was consistent, higher water content and shorter induction times was observed (e.g., the induction times of select RDF samples with 5.8% and 16.7% water content, was 446 and 270 min, respectively). Also, the induction time was affected by the size of a RDF sample. No relationship between bacterial fermentation and spontaneous ignition was observed. The linear relationship between the induction time and the inverse of the initial temperature of the RDF sample was obtained in the Arrhenius equation.     

Recycling PC and TV waste glass in clay bricks and roof tiles

Disposal of PC monitors and TV sets is a growing problem, with over 40% of the weight of these systems comprised of waste glasses with high Pb (funnel) or Ba–Sr concentrations (panel), making them unsuitable for recycling and manufacturing new glass. A possible way to re-use these glasses is in the manufacturing of clay bricks and roof tiles. This possibility was appraised by laboratory simulation of the brickmaking process and technological characterization of unfired and fired products. The recycling of both funnel and panel glasses into clay bodies is technologically feasible, resulting in a substantially reduced plasticity behaviour during shaping–drying (implying a reduction of mechanical strength), and a promotion of sintering during firing. No significant release of Pb, Ba, and Sr was observed during the firing and leaching test for the carbonate-poor body; in contrast, some Pb volatilization during firing and Sr leaching were observed for the carbonate-rich body. Additions of 2 wt.% appear to be practicable, while 5 wt.% glass induces unacceptable modifications of technological properties. The recommended amount is within 2 and 4 wt.%, depending on the characteristics of the clay bodies. The main constraint is that the glass must have a particle size below the limit of the pan mills used in brickmaking (<1 mm).     

The applicability of different waste materials for the production of lightweight aggregates

The applicability of different waste materials for the production of lightweight aggregates has been studied. The following waste materials were investigated: silica sludge, superfluous clay in the quarry, waste glass, and residue from the polishing process of different types of stone. SiC and MnO₂ were selected as foaming agents. Feldspar containing minerals and scrap glass were added in order to lower the softening point of the waste materials. The granules were prepared by mixing together finely ground waste with one or both of the selected foaming agents. The granules were then fired at different temperatures above the softening point of the glassy phase within the temperature range from 1150 to 1220 °C, where the foaming agent degasses, and the resulting gasses remain trapped in the glassy structure. The foaming process was observed by hot-stage microscopy. The properties of the so-obtained granules, such as their apparent density and compressive strength, were determined, and their microstructures were evaluating using SEM and polarizing microscopy.With the addition to clay of polishing residue from granite-like rocks, after firing at 1220 °C homogeneously porous granules with a density down to 0.42 g/cm³ were obtained, whereas with the addition to waste silica sludge of polishing residue from granite-like rocks and waste glass with a foaming agent, after firing at 1220 °C densities from 0.57 to 0.82 g/cm³ were obtained.