Revisiting the elemental composition and the calorific value of the organic fraction of municipal solid wastes

In this work, the elemental content (C, N, H, S, O), the organic matter content and the calorific value of various organic components that are commonly found in the municipal solid waste stream were measured. The objective of this work was to develop an empirical equation to describe the calorific value of the organic fraction of municipal solid waste as a function of its elemental composition. The MSW components were grouped into paper wastes, food wastes, yard wastes and plastics. Sample sizes ranged from 0.2 to 0.5 kg. In addition to the above individual components, commingled municipal solid wastes were sampled from a bio-drying facility located in Crete (sample sizes ranged from 8 to 15 kg) and were analyzed for the same parameters. Based on the results of this work, an improved empirical model was developed that revealed that carbon, hydrogen and oxygen were the only statistically significant predictors of calorific value. Total organic carbon was statistically similar to total carbon for most materials in this work. The carbon to organic matter ratio of 26 municipal solid waste substrates and of 18 organic composts varied from 0.40 to 0.99. An approximate chemical empirical formula calculated for the organic fraction of commingled municipal solid wastes was C₃₂NH₅₅O₁₆.     

Characterization of char derived from various types of solid wastes from the standpoint of fuel recovery and pretreatment before landfilling

Carbonization is a kind of pyrolysis process to produce char from organic materials under an inert atmosphere. In this work, chars derived from various solid wastes were characterized from the standpoint of fuel recovery and pretreatment of waste before landfilling. Sixteen kinds of municipal and industrial solid wastes such as residential combustible wastes, non-combustible wastes, bulky wastes, construction and demolition wastes, auto shredder residue, and sludges were carbonized at 500 degrees C for 1h under nitrogen atmosphere. In order to evaluate the quality of char as fuel, proximate analysis and heating value were examined. The composition of raw waste had a significant influence on the quality of produced char. The higher the ratio of woody biomass in waste, the higher heating value of char produced. Moreover, an equation to estimate heating value of char was developed by using the weight fraction of fixed carbon and volatile matter in char. De-ashing and chlorine removal were performed to improve the quality of char. The pulverization and sieving method seems to be effective for separation of incombustibles such as metal rather than ash. Most char met a 0.5 wt% chlorine criterion for utilization as fuel in a shaft blast furnace after it was subjected to repeated water-washing. Carbonization could remove a considerable amount of organic matter from raw waste. In addition, the leaching of heavy metals such as chrome, cadmium, and lead appears to be significantly suppressed by carbonization regardless of the type of raw waste. From these results, carbonization could be considered as a pretreatment method for waste before landfilling, as well as for fuel recovery.     

Municipal solid waste in Mostaganem city (Western Algeria)

The management of municipal solid waste (MSW) and valorisation is based on the understanding of MSW composition by its categories and physicochemical characteristics. In this study, we characterize and determine physicochemical parameters (density, fire loss, electric conductivity, average pH, moisture level, lower calorific value (LCV), total and organic carbon, and nitrogen) in order to establish MSW valorisation models for Mostaganem city (located in Western Algeria). The results show that organic matter represents 64.6% of waste, followed by paper-cardboard 15.9%, plastic 10.5%, glass 2.8%, textile 2.3%, metals 1.9%, and diverse materials 2%. These statistics are similar to results from developing countries, especially if organic matter, paper and plastic are taken into account, but differ from developed countries. This reflects the difference in lifestyle and consumption behaviour between the two communities. The parameters used to determine the possible valorisation model had the following average values: fire loss (63%); ash (37%); pH (6.1); electric conductivity (2.39 ms cm(-1)); total carbon (29.5%); nitrogen (1.5%); LCV (1028.6 kcal/kg), density (0.36), C/N (19.7) and moisture level (58.9%). The study shows that 31.1% of paper-cardboard, plastic, glass and metal wastes are recyclable. Incinerating MSW, with energy recovery, was a poor option because of the weak LCV (1028.6 kcal/kg). However, MSW produced a good methane yield of up to 1852.4 equivalent tons of oil per year. The agricultural benefits, C/N ratio values, levels of moisture and pH and the Tanner diagram all supported compost production.     

The effect of storage and mechanical pretreatment on the biological stability of municipal solid wastes

Modern mechanical–biological waste treatment plants for the stabilization of both the source-separated organic fraction of municipal solid wastes (OFMSW) and the mixed stream of municipal solid wastes (MSW) include a mechanical pretreatment step to separate recyclable materials such as plastics, glass or metals, before biological treatment of the resulting organic material. In this work, the role of storage and mechanical pretreatment steps in the stabilization of organic matter has been studied by means of respiration techniques. Results have shown that a progressive stabilization of organic matter occurs during the pretreatment of the source-separated OFMSW, which is approximately 30% measured by the dynamic respiration index. In the case of mixed MSW, the stabilization occurring during the reception and storage of MSW is compensated by the effect of concentration of organic matter that the pretreatment step provokes on this material. Both results are crucial for the operation of the succeeding biological process. Finally, respiration indices have been shown to be suitable for the monitoring of the pretreatment steps in mechanical–biological waste treatment plants, with a strong positive correlation between the dynamic respiration index and the cumulative respiration index across all samples tested.     

CHARACTERIZATION OF URBAN WASTES ACCORDING TO FERTILITY AND PHYTOTOXICITY PARAMETERS

Several urban wastes of different nature and level of organic matter stability (municipal solid wastes, sewage sludges and composts) have been characterized analysing fertility and phytotoxicity parameters. Sewage sludges showed the highest N and P values of all the wastes. The total K content of the wastes was low but almost all was available to plants. Mature composts had the lowest organic carbon and humic substances values as a consequence of organic matter mineralization during the composting process. The soluble C at pH 2/precipitated C ratio decreased as the stability of the organic matter increased. In spite of the heterogeneity of the wastes analysed, the organic matter/total organic C ratio was largely constant with a mean value of 2.05. In no case did the heavy metal levels exceed the maximum allowed by the EU disposition for sewage sludges use in agriculture. The highest levels of phytotoxic substances occurred in the fresh wastes. The germination rates and root length were highest with mature composts. Germination index and root length were negatively correlated with water soluble carbon (WSC) and WSC/N ratio. The principal component analysis showed that extractable C, soluble C at pH 2 and water soluble C were the C fractions which most contributed to the total variability.     

Use of thermal analysis techniques (TG-DSC) for the characterization of diverse organic municipal waste streams to predict biological stability prior to land application

The use of organic municipal wastes as soil amendments is an increasing practice that can divert significant amounts of waste from landfill, and provides a potential source of nutrients and organic matter to ameliorate degraded soils. Due to the high heterogeneity of organic municipal waste streams, it is difficult to rapidly and cost-effectively establish their suitability as soil amendments using a single method. Thermal analysis has been proposed as an evolving technique to assess the stability and composition of the organic matter present in these wastes. In this study, three different organic municipal waste streams (i.e., a municipal waste compost (MC), a composted sewage sludge (CS) and a thermally dried sewage sludge (TS)) were characterized using conventional and thermal methods. The conventional methods used to test organic matter stability included laboratory incubation with measurement of respired C, and spectroscopic methods to characterize chemical composition. Carbon mineralization was measured during a 90-day incubation, and samples before and after incubation were analyzed by chemical (elemental analysis) and spectroscopic (infrared and nuclear magnetic resonance) methods. Results were compared with those obtained by thermogravimetry (TG) and differential scanning calorimetry (DSC) techniques. Total amounts of CO₂ respired indicated that the organic matter in the TS was the least stable, while that in the CS was the most stable. This was confirmed by changes detected with the spectroscopic methods in the composition of the organic wastes due to C mineralization. Differences were especially pronounced for TS, which showed a remarkable loss of aliphatic and proteinaceous compounds during the incubation process. TG, and especially DSC analysis, clearly reflected these differences between the three organic wastes before and after the incubation. Furthermore, the calculated energy density, which represents the energy available per unit of organic matter, showed a strong correlation with cumulative respiration. Results obtained support the hypothesis of a potential link between the thermal and biological stability of the studied organic materials, and consequently the ability of thermal analysis to characterize the maturity of municipal organic wastes and composts.     

Municipal solid waste characteristics and management in Gümüşhane, Turkey

This paper presents a general overview of the current municipal solid waste (MSW) management in Gümüşhane Province, Turkey. In order to characterize the solid waste stream in the Municipality of Gümüşhane, a long-term study was conducted over a 52-week period between the spring of 2004 and the winter of 2005. In this study, percentage of components and specific weight of the MSW, the composting parameters (moisture content, total organic carbon, total nitrogen and pH), organic matter content, calorific value and the heavy metal concentrations (Cd, Cr, Cu, Ni, Pb, Zn, Fe, Mn, Co) of the compostable wastes sorted from the mixed MSW were determined and evaluated. In Gümüşhane, a mean of 70 tons of MSW are generated each day or 1 kg/day/capita. Approximately 4500 kg of the MSW were collected and sorted in a year, and the mean specific weight of these is 308 kg/m³. Approximately 30% of the MSW generated is compostable wastes and the yearly mean moisture content, organic matter content, C/N ratio and pH of these are 78%, 92.1%, 21.6/1 and 4.73, respectively, and approximately 24% of the MSW consists of recyclable materials. The recommended system deals with maximizing recycling and minimizing landfilling of the MSW, and consists of separation at source, collection, sorting, recycling, composting and sanitary landfilling. Heavy metal concentrations of the compostable wastes from the open dump were determined to decrease in the following order: Fe > Mn > Zn > Cr > Cu > Pb > Ni > Cd > Co.     

Agrochemical characterisation of the solid by-products and residues from the winery and distillery industry

The winery and distillery industry produces a great quantity of residues, whose management and disposal are environmental problems due to their seasonal character and some polluting characteristics. The main solid by-products and residues generated are grape stalk, grape pomace or marc, wine lee, exhausted grape marc and winery sludge. In this study, 87 samples of winery and distillery residues were collected from different Spanish wineries and distilleries. Electrical conductivity, pH, total organic matter, organic carbon, polyphenols and contents of plant nutrients and heavy metals were determined. The purpose of this research was to study the composition of these wastes and to find relationships in order to use easily analysable parameters to estimate their composition. In general, the winery and distillery residues showed low pH (mean values ranged from 3.8 to 6.8) and electrical conductivity values (1.62-6.15 dS m(-1)) and high organic matter (669-920 g kg(-1)) and macronutrient contents, especially in K (11.9-72.8 g kg(-1)). However, a notable polyphenol concentration (1.2-19.0 g kg(-1)) and low micronutrient and heavy metal contents were also observed, some of these properties being incompatible with agricultural requirements. Therefore, conditioning treatments are necessary prior to possible use of these wastes. In all wastes, significant correlations were found between easily determined parameters, such as pH, electrical conductivity and total organic matter, and most of the parameters studied. The regression models obtained are also discussed.     

On the effect of MSW moisture content on meeting target recycling rates

A mathematical model to calculate the recycle rates for packaging materials from the municipal solid wastes (MSW) built from the dry mass values that are obtained from the corresponding wet masses and their respective moisture contents is presented in this work. A possible universal methodology is also described to be used with the previous model so that reliable comparisons between indicators for different regions are feasible. Furthermore, this mathematical model demonstrates the effect of the moisture content of packaging materials on their recycling rates and constitutes a fundamental tool for operators and persons responsible for MSW management to define new policies and technical measures viewing the improvement of recycling rates. A theoretical study and the application of the model to the MEMSW of the Lisbon region shows that the moisture content of the mixed wastes plays a dominant role in the recycling rates of packaging materials such as paper, plastics and glass. Moreover, accounting for all relevant masses in the dry basis yields higher recycling rate values: increases of 32.8% for paper, 50% for plastics and 44.6% glass are observed.     

The use of commercial and industrial waste in energy recovery systems - A UK preliminary study

With 2020 energy targets set out by the EU fast approaching, the UK is trying to source a higher proportion of its energy from renewable resources. Coupled with this, a growing population and increasing trends in consumer demand have resulted in national waste loads increasing. A possible solution to both issues is energy-from-waste (EfW) technologies. Many studies have focused on municipal solid waste (MSW) as a potential feedstock, but appear to overlook the potential benefits of commercial and industrial waste (C&IW). In this study, samples of C&IW were collected from three North West waste management companies and Lancaster University campus. The samples were tested for their gross and net calorific value, moisture content, ash content, volatile matter, and also elemental composition to determine their suitability in EfW systems. Intra-sample analysis showed there to be little variation between samples with the exception two samples, from waste management site 3, which showed extensive variation with regards to net calorific value, ash content, and elemental analysis. Comparisons with known fuel types revealed similarities between the sampled C&IW, MSW, and refuse derived fuel (RDF) thereby justifying its potential for use in EfW systems. Mean net calorific value (NCV) was calculated as 9.47 MJ/kg and concentrations of sulphur, nitrogen, and chlorine were found to be below 2%. Potential electrical output was calculated using the NCV of the sampled C&IW coupled with four differing energy generation technologies. Using a conventional incinerator with steam cycle, total electrical output was calculated as 24.9 GWh, based on a plant operating at 100,000 tpa. This value rose to 27.0 GWh when using an integrated gasification combined cycle. A final aspect of this study was to deduce the potential total national electrical output if all suitable C&IW were to be used in EfW systems. Using incineration coupled with a steam turbine, this was determined to be 6 TWh, 1.9% of the national demand thereby contributing 6.5% towards the UK’s 2020 renewable electricity target.     

Low energy comsumption management of agricultural residues

In this paper, a mechanical filtering system to treat pig slurry is proposed. The filter was made from the aerobic decomposition product of the organic fraction of municipal wastes and wheat straw was used as the support.Using a pilot plant to treat 2100 liters of swine slurry, an adequate reduction in BOD₅; COD, and other parameters was obtained. The organic matter content of the material trapped in the filter was similar to that of compost and farmyard manure, but the nitrogen and phosphorous levels and the C/N ratio were more similar to farmyard manure. After passing through a filtering system, the treated liquid can be used for fertirrigation and as a feed for algae ponds. After a period of stabilization, the solid material can be mixed to produce manure. Although wheat straw was used as the support in this experiment, other agricultural wastes such as rice straw, corn stalks, millet stems, banana, cotton, and coconut trash can be used. Rather than municipal solid waste compost, other kinds of compost obtained from agricultural wastes such as leaves, bark, husks, etc., can be used as the filter.     

Potential emissions from two mechanically-biologically pretreated (MBT) wastes

The interaction of parameters determining the potential emissions of two different mechanically-biologically pretreated municipal solid wastes (MBT wastes) is elucidated in this work. The origins of the wastes are Germany and Sweden. By means of lab-scale experiments, increased stabilisation through composting is preferably determined by a decrease in respiration activity. Concurrently, the stabilisation is verified for the leachates by a decrease in COD, DOC, and BOD(5). Total organic carbon content reflects stabilisation less accurately. FT-IR and thermal analytical methods add valuable information about the state of degradation, especially when several distinct thermal parameters are taken into account. Mobility of Cr, Ni, Pb, and Zn produced by a batch leaching test with deionized water is reduced by the pretreatment of both materials. Mobility of copper unambiguously increased. A principle component analysis (PCA) of membrane fractionated leachates indicates an affinity of Cu to mobile humic acids or dissolved organic carbon. High Cr, Zn, and Ni contents in the solid co-occur with high contents of solid humic acids. To a lesser extent, this is also true for solid Cd, Cu, and Pb contents. Due to differences in required landfilling conditions, actual emissions and after-care phase length will depend on whether each waste is landfilled in Germany or Sweden.     

Selective organic compounds degradation under controlling composting conditions

Organic matter stabilization resulted from the decrease of cellulose, xylan, arabinan, acetyl groups, glucuronic acids, galacturonic acids (easily biodegradable fractions) and the increase of lignin (resistant compound) and humic substances coming from the initial wastes have been studied. A central composite experimental design was used to investigate the influence of environmental composting parameters (moisture, aeration and particle size) on organic matter evolution. The organic matter evolution was clearly influenced by the studied composting parameters. All results were concordant, with an increase of humic substances and lignin and a decrease of the rest of the cellulose and hemicellulose compounds. Lower cellulose, xylan, acetyl groups and glucuronic acids contents (higher degradation) have been observed under low particle size (1 cm) and higher moisture content (70%). However lower lignin and higher humic substances under medium (3 cm) to low particle size and low moisture content (40%) have been found.     

Numerical simulation of municipal solid waste combustion in a novel two-stage reciprocating incinerator

A mathematical model was presented in this paper for the combustion of municipal solid waste in a novel two-stage reciprocating grate furnace. Numerical simulations were performed to predict the temperature, the flow and the species distributions in the furnace, with practical operational conditions taken into account. The calculated results agree well with the test data, and the burning behavior of municipal solid waste in the novel two-stage reciprocating incinerator can be demonstrated well. The thickness of waste bed, the initial moisture content, the excessive air coefficient and the secondary air are the major factors that influence the combustion process. If the initial moisture content of waste is high, both the heat value of waste and the temperature inside incinerator are low, and less oxygen is necessary for combustion. The air supply rate and the primary air distribution along the grate should be adjusted according to the initial moisture content of the waste. A reasonable bed thickness and an adequate excessive air coefficient can keep a higher temperature, promote the burnout of combustibles, and consequently reduce the emission of dioxin pollutants. When the total air supply is constant, reducing primary air and introducing secondary air properly can enhance turbulence and mixing, prolong the residence time of flue gas, and promote the complete combustion of combustibles. This study provides an important reference for optimizing the design and operation of municipal solid wastes furnace.     

Thermal valorization of post-consumer film waste in a bubbling bed gasifier

The use of plastic bags and film packaging is very frequent in manifold sectors and film waste is usually present in different sources of municipal and industrial wastes. A significant part of it is not suitable for mechanical recycling but could be safely transformed into a valuable gas by means of thermal valorization. In this research, the gasification of film wastes has been experimentally investigated through experiments in a fluidized bed reactor of two reference polymers, polyethylene and polypropylene, and actual post-consumer film waste. After a complete experimental characterization of the three materials, several gasification experiments have been performed to analyze the influence of the fuel and of equivalence ratio on gas production and composition, on tar generation and on efficiency. The experiments prove that film waste and analogue polymer derived wastes can be successfully gasified in a fluidized bed reactor, yielding a gas with a higher heating value in a range from 3.6 to 5.6 MJ/m³ and cold gas efficiencies up to 60%.     

An assessment of municipal solid waste compost quality produced in different cities of India in the perspective of developing quality control indices

A study was conducted to investigate physico-chemical properties, fertilizing potential and heavy metal polluting potentials of municipal solid waste composts produced in 29 cities of the country. Results indicated that except a very few samples, all other samples have normal pH and EC. Organic matter as well as major nutrients N and P contents in MSW composts are generally low as compared to the composts prepared from rural wastes. Heavy metal contents in composts from bigger cities (>1 million population) were higher by about 86% for Zn, 155% for Cu, 194% for Cd, 105% for Pb, 43% for Ni and 132% for Cr as compared to those from smaller cities (<1 million population). Composts prepared from source separated biogenos wastes contained, on average, higher organic matter (by 57%), total N (by 77%) and total P (by 78%), but lower concentrations of heavy metals Zn (by 63%), Cu (by 78%), Cd (by 64%), Pb (by 84%), Ni (by 50%), and Cr (by 63%) as compared to those prepared from mixed wastes. Partial segregation at the site of composting did not improve quality of compost significantly in terms of fertilizing parameters and heavy metal contents. Majority of MSW composts did not conform to the quality control guideline of ‘The Fertilizer (Control) Order 1985’ in respect of total organic C, total P, total K as well as heavy metals Cu, Pb and Cr. In order to enable the relevant stakeholders to judge overall quality, a scheme has been proposed for the categorization of composts into different marketable classes (A, B, C, and D) and restricted use classes (RU-1, RU-2, and RU-3) on the basis their fertilizing potential and as well as potential for contaminating soil and food chain. Under the scheme, ‘Fertilizing index’ was calculated from the values of total organic C, N, P, K, C/N ratio and stability parameter, and ‘Clean index’ was calculated from the contents of heavy metals, taking the relative importance of each of the parameters into consideration. As per the scheme, majority of the compost samples did not belong to any classes and hence, have been found unsuitable for any kind of use. As per the regulatory limits of different countries, very few compost samples (prepared from source separated biogenos wastes) were found in marketable classes (A, B, C and D) and some samples (11–14) were found suitable only for some restricted use.     

Biochemical Parameters In Soils Regenerated By The Addition Of Organic Wastes

The effect of the addition of the organic fraction from a fresh municipal solid waste on the regeneration of a degraded soil from the Mediterranean area of Spain was studied. Sufficient waste to increase the organic matter of the soils by 0.5%, 1%, 1.5% and 2% was applied to a field in plots with a 10% incline. Forty months after treatment, increases were observed in organic matter, available nitrogen, water soluble carbohydrates and compounds determined by the Folin method (polyphenols and proteins) in all the treated plots as compared to the control. Changes were the greatest in the plot whose organic matter had been increased to 1.5%. An increase in enzymatic activity was also noticed (urease, BAA hydrolysed by protease, casein hydrolysed by protease, phosphatase, β-glucosidase and dehydrogenase) in the treated soils, particularly those which received higher rates of waste. The extracellular enzymatic activity of the plots treated with higher doses also increased, indicating a regeneration of the soils from a biochemical viewpoint. A positive correlation was observed between the parameters referring to microbial biomass and the enzymatic activities determined in the soils.     

Biodegradable municipal solid waste: characterization and potential use as animal feedstuffs

Five different fractions of the biodegradable municipal solid waste (BMSW) were evaluated as potential animal feedstuffs. For each source of waste (meat waste (MW), fish waste (FW), fruit and vegetables waste (FVW), restaurant waste (RW), household waste (HW)), samples were obtained from small shops (butchers, fishmongers, fruit and vegetable shops), restaurants and a MSW treatment plant (household waste). The chemical composition, microbiological characterization, dioxins, furans, PCB's and mineral content were determined for every type of waste fraction. The analysed biodegradable waste presented high moisture content (from 60% to 90%). Some fractions were dense in one nutrient: meat waste in ether extract, fish waste in crude protein, fruit and vegetable waste in nitrogen free extract. The other studied fractions (restaurant fraction and household fraction) presented a more balanced composition, but the presence of toxic concentrations of contaminants such as metals was higher than European legislation permitted values in animal feeding. From a microbiological standpoint, a heat treatment at 65 degrees C for 20 min was sufficient to ensure microbiological quality of the samples. This treatment was also advisable to reduce the moisture content: a lower moisture content facilitates the waste handling and processing and, therefore, the inclusion of these waste fractions in commercial animal diets. This paper presents a potential alternative for the recovery of organic matter content in municipal solid waste. The results obtained in this research and the feedstuffs legislation in force related to animal feed, indicated that some of the studied biodegradable waste fractions (meat waste, fruit and vegetable waste and fish waste) could be considered as alternatives to typical raw materials used in animal feeds.     

Modeling the energy content of combustible ship-scrapping waste at Alang-Sosiya, India, using multiple regression analysis

Alang-Sosiya is the largest ship-scrapping yard in the world, established in 1982. Every year an average of 171 ships having a mean weight of 2.10 x 10(6)(+/-7.82 x 10(5)) of light dead weight tonnage (LDT) being scrapped. Apart from scrapped metals, this yard generates a massive amount of combustible solid waste in the form of waste wood, plastic, insulation material, paper, glass wool, thermocol pieces (polyurethane foam material), sponge, oiled rope, cotton waste, rubber, etc. In this study multiple regression analysis was used to develop predictive models for energy content of combustible ship-scrapping solid wastes. The scope of work comprised qualitative and quantitative estimation of solid waste samples and performing a sequential selection procedure for isolating variables. Three regression models were developed to correlate the energy content (net calorific values (LHV)) with variables derived from material composition, proximate and ultimate analyses. The performance of these models for this particular waste complies well with the equations developed by other researchers (Dulong, Steuer, Scheurer-Kestner and Bento's) for estimating energy content of municipal solid waste.     

Study of drying systems for the utilization of biodegradable municipal solid wastes as animal feed

The effectiveness of different drying systems used for the dehydration of certain fractions of biodegradable municipal solid wastes with a high moisture content (fruit and vegetable remains) was analyzed. Some tests using small amounts of the material were carried out in natural and forced convection ovens. For larger quantities of wastes, a discontinuous cabinet dryer and a continuous rotary dryer were used. With these dryers, the moisture content was reduced from 800 to 100 g kg(-1). It was verified that the continuous rotary dryer was the most efficient type of equipment studied, since it allowed a dried waste to be obtained with better nutritional and microbiological qualities and in accordance to the specifications of the products for animal feeding.