Finished leather waste chromium acid extraction and anaerobic biodegradation of the products

Due to the amounts of chromium in the leachate resulting from leather leaching tests, chromium sulfate tanned leather wastes are very often considered hazardous wastes. To overcome this problem, one option could be recovering the chromium and, consequently, lowering its content in the leather scrap. With this objective, chromium leather scrap was leached with sulfuric acid solutions at low temperature also aiming at maximizing chromium removal with minimum attack of the leather matrix. The effects of leather scrap dimension, sulfuric acid and sodium sulfate concentration in the solutions, as well as extraction time and temperature on chromium recovery were studied, and, additionally, organic matrix degradation was evaluated. The best conditions found for chromium recovery were leather scrap conditioning using 25 mL of concentrated H₂SO₄/L solution at 293 or 313 K during 3 or 6 days. Under such conditions, 30–60 ± 5% of chromium was recovered and as low as 3–6 ± 1% of the leather total organic carbon (TOC) was dissolved. Using such treatment, the leather scrap area and volume are reduced and the residue is a more brittle material showing enhanced anaerobic biodegradability. Although good recovery results were achieved, due to the fact that the amount of chromium in eluate exceeded the threshold value this waste was still hazardous. Thus, it needs to be methodically washed in order to remove all the chromium de-linked from collagen.     

Seasonal generation and composition of garden waste in Aarhus (Denmark)

Garden waste generation and composition were studied in Aarhus, Denmark. The amount of garden waste generated varied seasonally, from 2.5 kg person^?1 month^?1 in winter to 19.4 kg person^?1 month^?1 in summer. Seasonal fractional composition and chemical characterization of garden waste were determined by sorting and sampling garden waste eight times during 1 year. On a yearly basis, the major fraction of garden waste was “small stuff” (flowers, grass clippings, hedge cuttings and soil) making up more than 90% (wet waste distribution) during the summer. The woody fractions (branches, wood) are more significant during the winter. Seasonal trends in waste chemical composition were recorded and an average annual composition of garden waste was calculated, considering the varying monthly generation and material fraction composition: the wet garden waste contained 40% water, 30% organic matter (VS) and 30% ash. The ash content suggests that the garden waste contains a significant amount of soil. This is in particular the case during summer. Of nutrients, the garden waste contained in average on a dry matter basis 0.6% N, 0.1% P, and 1.0% K. However, the contents varied significantly among the fractions and during the year. The content of trace elements (Cd, Cr, Cu, Hg, Ni, Pb, and Zn) was low.     

Evaluating the biochemical methane potential (BMP) of low-organic waste at Danish landfills

The biochemical methane potential (BMP) is an essential parameter when using first order decay (FOD) landfill gas (LFG) generation models to estimate methane (CH₄) generation from landfills. Different categories of waste (mixed, shredder and sludge waste) with a low-organic content and temporarily stored combustible waste were sampled from four Danish landfills. The waste was characterized in terms of physical characteristics (TS, VS, TC and TOC) and the BMP was analyzed in batch tests. The experiment was set up in triplicate, including blank and control tests. Waste samples were incubated at 55 °C for more than 60 days, with continuous monitoring of the cumulative CH₄ generation. Results showed that samples of mixed waste and shredder waste had similar BMP results, which was in the range of 5.4–9.1 kg CH₄/ton waste (wet weight) on average. As a calculated consequence, their degradable organic carbon content (DOCC) was in the range of 0.44–0.70% of total weight (wet waste). Numeric values of both parameters were much lower than values of traditional municipal solid waste (MSW), as well as default numeric values in current FOD models. The sludge waste and temporarily stored combustible waste showed BMP values of 51.8–69.6 and 106.6–117.3 kg CH₄/ton waste on average, respectively, and DOCC values of 3.84–5.12% and 7.96–8.74% of total weight. The same category of waste from different Danish landfills did not show significant variation. This research studied the BMP of Danish low-organic waste for the first time, which is important and valuable for using current FOD LFG generation models to estimate realistic CH₄ emissions from modern landfills receiving low-organic waste.     

GHG emission factors developed for the collection,transport and landfilling of municipal waste in South African municipalities

Greenhouse gas (GHG) emission factors are used with increased frequency for the accounting and reporting of GHG from waste management. However, these factors have been calculated for developed countries of the Northern Hemisphere and are lacking for developing countries. This paper shows how such factors have been developed for the collection, transport and landfilling of municipal waste in South Africa. As such it presents a model on how international results and methodology can be adapted and used to calculate country-specific GHG emission factors from waste. For the collection and transport of municipal waste in South Africa, the average diesel consumption is around 5 dm³ (litres) per tonne of wet waste and the associated GHG emissions are about 15 kg CO₂ equivalents (CO₂ e). Depending on the type of landfill, the GHG emissions from the landfilling of waste have been calculated to range from ?145 to 1016 kg CO₂ e per tonne of wet waste, when taking into account carbon storage, and from 441 to 2532 kg CO₂ e per tonne of wet waste, when carbon storage is left out. The highest emission factor per unit of wet waste is for landfill sites without landfill gas collection and these are the dominant waste disposal facilities in South Africa. However, cash strapped municipalities in Africa and the developing world will not be able to significantly upgrade these sites and reduce their GHG burdens if there is no equivalent replacement of the Clean Development Mechanism (CDM) resulting from the Kyoto agreement. Other low cost avenues need to be investigated to suit local conditions, in particular landfill covers which enhance methane oxidation.     

Odorous gaseous emissions as influence by process condition for the forced aeration composting of pig slaughterhouse sludge

Compost sustainability requires a better control of its gaseous emissions responsible for several impacts including odours. Indeed, composting odours have stopped the operation of many platforms and prevented the installation of others. Accordingly, present technologies collecting and treating gases emitted from composting are not satisfactory and alternative solutions must be found. Thus, the aim of this paper was to study the influence of composting process conditions on gaseous emissions. Pig slaughterhouse sludge mixed with wood chips was composted under forced aeration in 300 L laboratory reactors. The process conditions studied were: aeration rate of 1.68, 4.03, 6.22, 9.80 and 13.44 L/h/kg of wet sludge; incorporation ratio of 0.55, 0.83 and 1.1 (kg of wet wood chips/kg of wet sludge), and; bulking agent particles size of <10, 10 < 20 and 20 < 30 mm. Out-going gases were sampled every 2 days and their composition was analysed using gas chromatography coupled with mass spectrometry (GC–MS). Fifty-nine compounds were identified and quantified. Dividing the cumulated mass production over 30 days of composting, by odour threshold, 9 compounds were identified as main potential odour contributors: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone, 1-propanol-2-methyl, dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide and acetophenone. Five gaseous compounds were correlated with both aeration rate and bulking agent to waste ratio: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone and 1-propanol-2-methyl. However, dropping the aeration rate and increasing the bulking agent to waste ratio reduced gaseous odour emissions by a factor of 5–10, when the required threshold dilution factor ranged from 10⁵ to 10⁶, to avoid nuisance at peak emission rates. Process influence on emissions of dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide were poorly correlated with both aeration rate and bulking agent to waste ratio as a reaction with hydrogen sulphide was suspected. Acetophenone emissions originated from the wood chips. Olfactory measurements need to be correlated to gaseous emissions for a more accurate odour emission evaluation.     

Physico-chemical analysis and calorific values of poultry manure

Spain is one of the major producers of broilers and laying hens in the European Union, with an overall market share of around 12%. The poultry manure that is produced is usually employed as fertilizer on cropland, either directly or after a composting process. In some cases, however, this waste is transported over 120 km to be used as fertilizer, with the resulting high transport costs. In other countries, poultry manure is used as an alternative natural fuel source for power generation. In this study, poultry manure from all the laying hen farms in Asturias was characterized with a view to its possible use as an energy source. The Higher Heating Values on a dry basis (experimental) varies between 12,052 and 13,882 kJ/kg. Lower Heating Values (LHVs) on a wet basis range are much lower (mean values of 2664 kJ/kg) due to the high moisture content of poultry manure. Accordingly, the co-combustion of this waste with other types of waste such as forest and wood waste (LHV on a wet basis of 8044 and 15,830 kJ/kg, respectively) or municipal solid waste (LHV on a wet basis of 10,725 kJ/kg) should be considered as an alternative energy source. Chlorine and sulphur contents in dry matter vary around mean values of 0.64% and 0.11%, respectively. The waste also presents high amounts of Ca (4.84%) and K (2.38%).     

Management of agricultural biomass wastes: Preliminary study on characterization and valorisation in clay matrix bricks

In this work the feasibility of using woody agricultural biomass wastes as grapes and cherries seeds, sawdust, as pore forming agent, and sugar cane ash, as silica precursor, in bricks, were reported.Sawdust and grapes and cherries seeds, thanks to their organic substances content, during their combustion, bring an energetic support in the bricks firing phase and act as pore forming agent. Usually the addition of this kind of waste is limited to 10 wt.% in order to reach an equilibrium between positive (weight and shrinkage decrease and porosity increase) and negative (increase of water absorption and mechanical resistance decrease) effects. The results show that grapes and cherries seeds, added in a percentage of 5 wt.% to a brick formulation, have better influence with respect to the sawdust, maintaining the mechanical properties of the fired brick (950 °C), showing modulus of rupture around 21–23 MPa with a weight reduction of 3–10% (respect to the standard one). Regarding the sugar cane ash, the addition of 5 wt.% improves the mechanical properties (modulus of rupture around 27 MPa) and no weight decrease is observed. These results confirmed the role played by this kind of agricultural waste, which thanks to its high silica content (61 wt.%) is capable to demonstrate a filler and plasticity reducing effect on the brick bodies. Tests carried out highlighted that the addition of these by-products (5 wt.%) do not change negatively the main technological properties measured (water absorption, linear shrinkage, flexural resistance, etc.) and permit to hypothesize their use to obtain bricks with both insulating and higher mechanical properties using a pore agent forming or silica carrier alternative raw materials, respectively.     

Behavior of TiO2 nanoparticles during incineration of solid paint waste: A lab-scale test

In order to assess the potential impacts posed by products containing engineered nanoparticles, it is essential to generate more data about the release of these particles from products’ life cycle. Although first studies were performed to investigate the release of nanoparticles from use phase, very few data are available on the potential release from recycling or disposal of nano-enhanced products.In this work, we investigated the behavior of TiO₂ nanoparticles from incineration of solid paint waste containing these particles. Solid paint debris with and without TiO₂ nanoparticles were treated in a lab scale incineration plant at 950 °C (combustion temperature) and in oxidizing atmosphere. The obtained ashes were also vitrified with additives and the release of Ti was finally evaluated by leaching test. From our incineration lab-scale experiment, we did not observe a release of TiO₂ nanoparticles into the atmosphere, and Ti was attached to the surface of obtained solid residues (i.e. ashes). The characterization of ashes showed that TiO₂ nanoparticles reacted during the incineration to give calcium titanate. Finally, a very low release of Ti was measured, less 1 mg/kg, during the leaching test of ashes vitrified with glass cullet and feldspathic inert. Our work suggests that TiO₂ nanoparticles added in paints may undergo to physicochemical transformation during the incineration, and that Ti found in ashes may be strongly immobilized in glass matrix. Since this conclusion is based on lab-scale experiment, further research is required to identify which nanoparticles will be emitted to the environment from a real-word-incineration system of household hazardous waste.     

Composites Produced from Natural Rubber and Chrome-Tanned Leather Wastes: Evaluation of their In Vitro Toxicological Effects for Application in Footwear and Textile Industries

A new composite has been developed from natural rubber and chrome-tanned leather waste for use in footwear and textile industries. The contribution of this material to environmental quality and sustained development should be highligh because chrome tanned leather wastes, a major environmental problem, can be recycled. However, the safety of this new material for human use is questionable, as it is already well reported in the literature that chromium, particularly in its hexavalent oxidation state, can be genotoxic and carcinogenic to living beings. Thus, the aim of this study was to evaluate in vitro biocompatibility of this composite material for possible use in the footwear and textile industries, through cytotoxicity, cell adhesion, and genotoxicity tests. Inductively coupled plasma optical emission spectrometry (ICP-OES) was used to measure both concentrations of total and hexavalent chromium. Based on the findings, it was concluded that the composite exhibits low levels of cytotoxicity and genotoxicity, and possesses favorable properties for initial cell adhesion. Furthermore, it was verified that the composites released low concentrations of chromium and that the predominant species released would be trivalent chromium. The results of the present study open the possibility of the incorporation of solid residues of tanned leather into chromium without necessarily the chromium contained in these residues influences the toxicity and genotoxicity of this new material.     

Impact of different particle size distributions on anaerobic digestion of the organic fraction of municipal solid waste

Particle size may significantly affect the speed and stability of anaerobic digestion, and matching the choice of particle size reduction equipment to digester type can thus determine the success or failure of the process. In the current research the organic fraction of municipal solid waste was processed using a combination of a shear shredder, rotary cutter and wet macerator to produce streams with different particle size distributions. The pre-processed waste was used in trials in semi-continuous ‘wet’ and ‘dry’ digesters at organic loading rate (OLR) up to 6 kg volatile solids (VS) m^?3 day^?1. The results indicated that while difference in the particle size distribution did not change the specific biogas yield, the digester performance was affected. In the ‘dry’ digesters the finer particle size led to acidification and ultimately to process failure at the highest OLR. In ‘wet’ digestion a fine particle size led to severe foaming and the process could not be operated above 5 kg VS m^?3 day^?1. Although the trial was not designed as a direct comparison between ‘wet’ and ‘dry’ digestion, the specific biogas yield of the ‘dry’ digesters was 90% of that produced by ‘wet’ digesters fed on the same waste at the same OLR.     

Thermal valorization of footwear leather wastes in bubbling fluidized bed combustion

Transformation of hide (animal skins) into leather is a complicated process during which significant amounts of wastes are generated. Footwear is the sector that consumes the major part of leather (60%). Logically, this industry is producing the largest quantity of leather wastes. The objective of this work was to demonstrate the technical feasibility of fluidized bed technology to recover the energy from burning footwear leather wastes. Considering the characteristics of leather waste, especially the heating value (12.5-21 MJ/kg), it can be considered a fairly good fuel. Moreover, leather waste has suitable characteristics for combustion, e.g., high volatile matter (76.5%) and low ash content (5.2%). Two factors deserve special attention: N3O and NOx emissions as a consequence of its unusual high nitrogen content (14.1%) and the chromium speciation because chromium is the main element of ash (3.2%) due to its use in leather tanning. A series of experiments has been carried out in a 0.1 MWt bubbling fluidized bed pilot plant. The combustion efficiency, flue gas composition and chromium speciation were investigated. Despite having high nitrogen content, a low conversion rate of fuel-N to NOx and N2O was attained. Chromium was concentrated in the solid streams and it was consistently found as Cr(III+); no presence of Cr(VI+) was detected.     

Thermal and hydrometallurgical recovery methods of heavy metals from municipal solid waste fly ash

Heavy metals in fly ash from municipal solid waste incinerators are present in high concentrations. Therefore fly ash must be treated as a hazardous material. On the other hand, it may be a potential source of heavy metals. Zinc, lead, cadmium, and copper can be relatively easily removed during the thermal treatment of fly ash, e.g. in the form of chlorides. In return, wet extraction methods could provide promising results for these elements including chromium and nickel. The aim of this study was to investigate and compare thermal and hydrometallurgical treatment of municipal solid waste fly ash. Thermal treatment of fly ash was performed in a rotary reactor at temperatures between 950 and 1050 °C and in a muffle oven at temperatures from 500 to 1200 °C. The removal more than 90% was reached by easy volatile heavy metals such as cadmium and lead and also by copper, however at higher temperature in the muffle oven. The alkaline (sodium hydroxide) and acid (sulphuric acid) leaching of the fly ash was carried out while the influence of temperature, time, concentration, and liquid/solid ratio were investigated. The combination of alkaline-acidic leaching enhanced the removal of, namely, zinc, chromium and nickel.     

Emission of volatile sulfur compounds during composting of municipal solid waste (MSW)

Volatile sulfur compounds (VSCs) are the main source for malodor from composting plants. In this study, the VSCs generated from composting of 15–80 mm municipal solid waste (T0), kitchen waste (T1) and kitchen waste mixed dry cornstalks (T2) were measured in 60 L reactors with forced aeration for a period of 30 days. The VSCs detected in all treatments were hydrogen sulfide (H₂S), methyl mercaptan (MM), dimethyl sulfide (DMS), carbon bisulfide (CS₂) and dimethyl disulfide (DMDS). Over 90% of the VSCs emissions occurred during the first 15 days, and reached their peak values at days 4–7. The emission profiles of five VSCs species were significantly correlated with internal materials temperature and outlet O₂ concentration (p < 0.05). Total emissions of the VSCs were 216.1, 379.3 and 126.0 mg kg^?1 (dry matter) for T0, T1 and T2, respectively. Among the five VSCs, H₂S was the most abundant compound with 39.0–43.0% of total VSCs released. Composting of kitchen waste from separate collection posed a negative influence on the VSC and leachate production because of its high moisture content. An addition of dry cornstalks at a mixing ratio of 4:1 (wet weight) could significantly reduce the VSCs emissions and avoid leachate. Compared to pure kitchen waste, VSCs were reduced 66.8%.     

Potential use of densified polymer-pastefill mixture as waste containment barrier materials

Mining activities generate a large amount of solid waste, such as waste rock and tailings. The surface disposal of such waste can create several environmental and geotechnical problems. Public perception and strict government regulations with regards to the disposal of such waste compel the mining industry to develop new strategies which are environmentally sound and cost effective. In this scenario, recycling of such waste into mining or civil engineering construction materials have become a great challenge for the mining and civil engineering community. Hence, in this study, taking advantage of the inherent low hydraulic conductivity of paste tailings (pastefill), small amounts (0.05, 0.1, 0.2, 0.5%) of a super absorbent polymer (SAP) are added to the latter after moisturizing the tailings. The resulting densified polymer-pastefill (PP) materials are compacted and submitted to permeability tests at room temperature and performance tests under cyclic freeze–thaw and wet–dry conditions to evaluate their suitability as a barrier for waste containment facilities. Valuable results are obtained. It is found that the hydraulic conductivity of the proposed barrier material (PP) decreases as the amount of SAP increases. Hydraulic conductivity values as low as 1 × 10^?7 and 6 × 10^?9 cm/s are obtained for PPs which contain 0.1–0.5% SAP, respectively. The PP material also shows relatively good resistance to cyclic freeze–thaw and wet–dry stresses. The results show that negligible to acceptable changes in hydraulic conductivity occur after five freeze–thaw and six wet–dry cycles. None of the changes reach one order of magnitude. As a final step, a cost analysis is undertaken to evaluate the economical benefits that could be drawn from such a proposed barrier material. When compared to a conventional compacted sand–bentonite barrier with 12% bentonite concentration, it is found that the benefit realized could be estimated to 98, 96 and 90% when using PP material that contains 0.10, 0.20 and 0.5% of SAP. From this study, it can be concluded that PP materials show encouraging performance properties for barrier design.     

Characterization, Fluxes and Toxicity of Leather Tanning Bath Chemicals in a Large Tanning District Area (IT)

The leather tanning industry is perceived as responsible of a significant consume of natural resources and output of wastes such as high concentration of organics, salts and heavy metals such as chromium, both in solid and liquid form as a result. Now as ever the future of tanneries strongly depends on the increase of their awareness that a sustainable industry for the future means embracing a forward-looking philosophy of the leather making process through optimal resource management within the tannery. This study reports the characterization of some chemicals used in a large tanning district area in terms of COD, BOD, aromaticity (UV₂₈₀) and double bond (UV₂₅₄) absorbance measurements, toxicity on fresh and saline water as well as terrestrial species, GC-MS scanning. The study provides a consistent set of information on tannin-associated concentration-related trends and suggests novel criteria in defining control quality for evaluating environmental impact of leather tanning industry.     

Microwave inactivation of Bacillus atrophaeus spores in healthcare waste

Public healthcare wastes from the region of Ribeirão Preto, Brazil, pre-sterilized in an autoclave, were inoculated with spores of Bacillus atrophaeus for microwave processing on a laboratory scale. The influence of waste moisture (40%, 50% and 60% wet basis), presence of surfactant, power per unit mass of waste (100, 150 and 200 W/kg) and radiation exposure time (from 5 to 40 min) on the heating curves was investigated. The most favorable conditions for waste heating with respect to moisture and use of surfactant were then applied in an experimental analysis of the degree of inactivation of B. atrophaeus spores as a function of time and power per unit mass of waste. Based on Chick’s and Arrhenius laws, the experimental results were adjusted by the least squares method to determine the activation energies (9203–5782 J/mol) and the Arrhenius pre-exponential factor (0.23 min^?1). The kinetic parameters thus obtained enabled us to predict the degree of inactivation achieved for B. atrophaeus spores in typical healthcare waste. The activation energy was found to decrease as the power per waste mass increased, leading to the conclusion that, in addition to the thermal effect on the inactivation of B. atrophaeus spores, there was an effect inherent to radiation.     

Microbial oxygen uptake in sludge as influenced by compost physical parameters

The wide range of optimal values reported for the physical parameters of compost mixtures suggest that their interactive relationships should be investigated. The objective of this study was to examine the microbial O₂ uptake rate (OUR) in 16 sludge waste recipes, offering a range of moisture content (MC), waste/bulking agent (W/BA) ratio and BA particle size levels determined using a central composite experimental design. The 3 kg samples were maintained at a constant temperature and aeration rate for 28 days, during which a respirometer recorded O₂ uptake to provide a measure of microbial activity and biodegradability. The cumulative O₂ consumption after 14 and 28 days was found to be significantly influenced by MC, W/BA ratio, BA particle size and the interaction between MC and W/BA ratio (p < 0.05). Using multivariate regression analysis, the experimental data was used to generate a model with good predictive ability for cumulative O₂ consumption after 28 days as a function of the significant physical variables (R² = 0.84). The prediction of O₂ uptake by the model depended highly on the interaction between MC and W/BA ratio. A MC outside of the traditional 50–60% (wet basis) range still resulted in a high level of microbial O₂ uptake as long as the W/BA ratio was adjusted to maintain a suitable O₂ exchange in the sample. The evolution of OUR in the samples was also investigated, uncovering strong associations between short and long-term respirometric indices, such as peak OUR and cumulative O₂ consumption (p < 0.005). Combining peak OUR data with cumulative O₂ consumption after 14 days allowed for accurate predictions of cumulative O₂ after 28 days of aeration (R² = 0.96), implying that future studies need only run trials up to 14 days to evaluate the overall O₂ consumption or biodegradability of similar sludge mixtures.     

Precious metals and rare earth elements in municipal solid waste – Sources and fate in a Swiss incineration plant

In Switzerland many kinds of waste, e.g. paper, metals, electrical and electronic equipment are separately collected and recycled to a large extent. The residual amount of municipal solid waste (MSW) has to be thermally treated before final disposal. Efforts to recover valuable metals from incineration residues have recently increased. However, the resource potential of critical elements in the waste input (sources) and their partitioning into recyclable fractions and residues (fate) is unknown. Therefore, a substance flow analysis (SFA) for 31 elements including precious metals (Au, Ag), platinum metal group elements (Pt, Rh) and rare earth elements (La, Ce, etc.) has been conducted in a solid waste incinerator (SWI) with a state-of-the-art bottom ash treatment according to the Thermo-Re® concept. The SFA allowed the determination of the element partitioning in the SWI, as well as the elemental composition of the MSW by indirect analysis. The results show that the waste-input contains substantial quantities of precious metals, such as 0.4 ± 0.2 mg/kg Au and 5.3 ± 0.7 mg/kg Ag. Many of the valuable substances, such as Au and Ag are enriched in specific outputs (e.g. non-ferrous metal fractions) and are therefore recoverable. As the precious metal content in MSW is expected to rise due to its increasing application in complex consumer products, the results of this study are essential for the improvement of resource recovery in the Thermo-Re® process.     

Effect of nine years of animal waste deposition on profile distribution of heavy metals in Abeokuta,south-western Nigeria and its implication for environmental quality

Uncontrolled deposition of waste from animal farms is a common practice in south-western Nigeria, and the presence of heavy metals in soil constitutes environmental and health hazards by polluting the soil, ground water, adjoining streams and rivers. The study investigated the profile distribution of Mn, Pb, Cd, Zn, Fe, Cu, Ni and Cr in some tropical Alfisols in south-western Nigeria after nine years disposal of animal wastes. The amount of these metals in the soil horizons was high enough to cause health and phytotoxic risks. All the metals except Zn and Cr increased down the profile, while Mn, Pb, Cd, Fe, Cu and Ni accumulated at 80–120 cm depth. The increment of these metals at this depth over the top soil were 26%, 143%, 72%, 47%, 328% for Mn, Pb, Cd, Cu and Ni, respectively. It thus, shows their mobility and the possibility of polluting ground water. The Mn content at the poultry and cattle waste sites increased by 127% and 25%, respectively over the control, while that of cattle and swine dump site for Cd content were 9.82 and 15.63 mg kg^?1, respectively. Lead content also increased by 8.52 and 5.25 mg kg^?1, respectively.There was the accumulation of Zn and Cu at the swine dump site while the cattle dump site had the highest amounts of nickel and chromium. The least amount of Fe was recorded at the swine waste dump site. The reduction in organic matter with depths together with the reduced pH might have favored the mobility of the metals. The ranking of pollution among the sites was poultry > swine > cattle > sheep and could be due to the type of ration fed, the vaccination programmes, sanitation programmes and other management practices.     

Evaluation of a classification method for biodegradable solid wastes using anaerobic degradation parameters

We studied the biochemical and anaerobic degradation characteristics of 29 types of materials to evaluate the effects of a physical composition classification method for degradable solid waste on the computation of anaerobic degradation parameters, including the methane yield potential (L₀), anaerobic decay rate (k), and carbon sequestration factor (CSF). Biochemical methane potential tests were conducted to determine the anaerobic degradation parameters of each material. The results indicated that the anaerobic degradation parameters of nut waste were quite different from those of other food waste and nut waste was classified separately. Paper was subdivided into two categories according to its lignin content: degradable paper with lignin content of <0.05 g g VS^?1, and refractory paper with lignin content >0.15 g g VS^?1. The L₀, k, and CSF parameters of leaves, a type of garden waste, were similar to those of grass. This classification method for degradable solid waste may provide a theoretical basis that facilitates the more accurate calculation of anaerobic degradation parameters.