What substances or objects should be recycled? The recycling legislative experience in Taiwan

The legislative framework of waste management in Taiwan has never been efficient, mainly due to unclear definitions and regulations. In 2002, this system was split into two parts by enacting a new law, the Resource Recycling and Re-use Act (RRRA). However, it then became more complicated and recycling effectiveness was impeded. The causes were mainly the unclear definitions, conflicts about the scope, and issues between the RRRA and the Waste Disposal Act (WDA). This article examines the recycling legislation experience in Taiwan, and proposes two modifications for resolving these problems. The first proposal is merging these two acts into one. The second proposed modification maintains a two-system structure but introduces a new subject, discards, into the law. The subject of discards is further categorized as recyclable resources or waste, which correspond to recycling operations and disposal operations, respectively. The new structures, interfaces, prerequisites, properties, and comparisons are also explained.     

The Effect of UV-B Irradiation on the Biodegradability of Poly-β-Hydroxybutyrate (PHB) and Poly-ɛ-Caprolactone (PCL)

The biodegradability of poly--hydroxybutyrate and poly--caprolactone in soil compostage before and after irradiation of the polymers for 192, 425, and 600 h in a Weather-Ometer was examined. The biodegradability tests were done in soil compostage at pH 7.0, 9.0, and 11.0 to assess the influence of this parameter on degradation. The rate of degradation was directly proportional to the soil alkalinity. Poly--hydroxybutyrate showed the greatest weight loss and aging in a Weather-Ometer did not significantly increase the biodegradation, except when the polymer was aged for 425 h and buried in soil compostage of pH 11.0.     

A carbon-13 method for evaluating degradation of starch-based polymers

A new method for evaluating biodegradability of starch-based and certain other polymer blends uses the pre- and postexposure stable carbon isotope composition of material coupled with weight loss data to determine which components have degraded. The naturally occurring stable isotope of carbon.¹³C, is enriched in corn starch (¹³C, approx. –11) compared to petroleum-derived synthetic polymers (¹³C, approx. –32). Results on starch-synthetic polymer blends indicate that the ¹³C signatures of these blends are near-linear mixtures of their component ¹³C. Values of a ¹³C for starch-synthetic polymer blends exposed to biologically active laboratory soil and artificial seawater conditions are depleted in¹³C compared to unexposed samples, suggesting loss of the starch component. Combined with weight loss data for the exposed samples, the ¹³C values are statistically consistent with models requiring loss of the soluble component glycerin, followed by loss of starch, then petrochemical polymer, or simultaneous loss of starch and petrochemical polymer. Replicate ¹³C analyses of starch-synthetic polymer blends increase the statistical power of this relatively inexpensive, accessible technique to discriminate between degrading components.     

Synthesis and environmental degradation of polyesters based on poly (ε-caprolactone)

Poly (-caprolactone) (PCL), poly (-valerolactone) (PVL), poly (-caprolactone-co--valerolactone) [P(CL-co-VL)], and poly (-caprolactone-co-ethylene oxide-co--caprolactone) (PCL-PEO-PCL) were synthesized by ring-opening and diol-initiated polymerization of -caprolactone and -valerolactone. The degradation of the samples by chemical hydrolysis and in a soil burial test was evaluated. It was found that PCL, PVL, and P(CL-co-VL) degrade mainly enzymatically. The rate of degradation depends on their molecular weight, chemical structure, composition, and morphology. PCL-PEO-PCL block copolymers exhibit a repelling effect to the microorganisms in the soil, which depends on the molecular weight and relative amount of PEO block in the copolymer.     

The degradation of gel-spun poly(β-hydroxybutyrate) “wool”

The apparent biodegradability and biocompatibility of the microbially produced polyester, poly(-hydroxybutyrate) (PHB), has been the focus of much research by a number of authors with regard to its potential for use in packaging and medical implantation devices. PHB has recently been produced by gel-spinning into a novel form, with one possible application being as a wound scaffolding device, designed to support and protect a wound against further damage while promoting healing by encouraging cellular growth on and within the device from the wound surface. This new nonwoven form combines a large volume with a low mass, has an appearance similar to that of cotton wool, and has been called wool because of this similarity. The hydrolytic degradation of this wool was investigated in an accelerated model of pH 10.6 and temperature 70°C. It was determined that the PHB wool gradually collapsed during degradation. The surface area-to-volume ratio was concluded to be a primary influencing factor. Degradation was characterized by a reduction in the glass transition temperatures and melting points and a fusion enthalpy peak of maximum crystallinity, (88%), which coincided with the point of matrix collapse.     

Landfill mining and waste characterization: a strategy for remediation of contaminated areas

This article describes landfill-mining tests, including excavation, screening, and fraction characterization, carried out in the Msalycke and Gladsax landfills for municipal solid waste (MSW) in Sweden. The excavated waste in these two sites was 17–22 and 23–25 years old, respectively. The main part of Msalycke was unaffected by degradation, and during excavations no substantial amount of biogas was detected. After screening, three size fractions were obtained: <18mm, 18–50mm, and >50mm. Soil amendment and anaerobic digestion with energy extraction are suggested for the first and second fraction, respectively. Incineration with energy recovery is possible with the third fraction after any coarse (inert) material is removed, and construction/demolition waste can easily be recycled provided that it is not contaminated by hazardous material. Excavated waste taken from different depths was also analysed and compared in relation to composition, calorific value, and leachate constituents.     

Investigation of the Aerobic Biodegradability of Several Types of Cyclodextrins in a Laboratory-Controlled Composting Test

The biodegradation of several types of cyclodextrins (CDs) under laboratory-controlled composting conditions was investigated. CDs are used in a broad range of applications in food, pharmaceutical, medical, chemical, and textile industries because of their specific chemical characteristics related to their hydrophobic interior and hydrophilic exterior. The three naturally occurring cyclodextrins -CD, -CD, and -CD proved to be completely and readily biodegradable. Chemical modification of these basic compounds can have a major impact on the biodegradation rate and final biodegradation percentage. Fully acetylated -CD and -CD were found to be nonbiodegradable during 45 days of composting. Reducing the degree of acetylation had a positive effect on the biodegradation. Complete biodegradation was obtained for partially acetylated -CD with a degree of substitution (DS) of 7. The methylation (DS = 13) of -CD resulted in an undegradable compound during the 47 days composting, while (2-hydroxy)propyl--CD reached a plateau in biodegradation at a percentage of 20%. The incorporation of the antimicrobial agents imazalil and allyl-isothiocyanate into -CD had no negative impact on biodegradation, which makes these antimicrobial agents/CD complexes suitable for incorporation into biodegradable active packaging.     

Preparation conditions and swelling equilibria of biodegradable hydrogels prepared from microbial poly(γ-glutamic acid) and poly(ε-lysine)

Biodegradable hydrogels prepared by -irradiation from microbial poly(amino acid)s are reviewed. pH-sensitive hydrogels were prepared by means of -irradiation of poly(-glutamic acid) (PGA) produced byBacillus subtilis IFO3335 and poly(-lysine) (PL) produced byStreptomyces albulus in aqueous solutions. The preparation conditions, swelling equilibria, hydrolytic degradation, and enzymatic degradation of these hydrogels were studied. A hydrogel with a wide variety of swelling behaviors has been produced by -irradiation from a mixture solution of PGA and PL.Paper presented at the 4th International Workshop on Biodegradable Plastics and Polymers, October 11–14, 1995, Durham, New Hampshire, USA.     

Liquid crystallinity of levan/water/starch solutions

Transmitted light measurements performed with a UV-visible spectrophotometer were used to characterize how starch affects the position of boundaries on the phase diagram for dilute aqueous solutions of levan (a branched polymer of fructose). Data were collected in the range 15 to 70°C; the minimum concentrations required for separation of a nematic phase and the minimum concentration required for a fully nematic solution were identified within this range. While hard interactions (repulsion between rod-like molecular segments) dictate the formation of a liquid crystalline phase at and above ambient temperature in the absence of starch, soft interactions become more significant as solutions are cooled toward ambient when starch is present. Small amounts of starch might be used as a filler to modify the mechanical properties (while retaining the process-related benefits) of levan films cast from liquid crystalline solution.     

Decomposition reactions of epoxy resin and polyetheretherketone resin in sub- and supercritical water

Epoxy resin and polyetheretherketone (PEEK) resin were decomposed into their monomers such as phenol, cresols, and their analogues by thermal treatment in sub- and supercritical water in a 10-ml tubing bomb reactor. The addition of basic compounds such as Na₂CO₃ was effective in promoting the decomposition reaction of the resins. In the reaction of epoxy resin, the yield of identified products reached 10% for the reaction at 703K over 1h. In the reaction of PEEK resin, the total yield of phenol and dibenzofuran reached 88% for the reaction at 703K over 3h. Chemical participation of water in the decomposition reaction was confirmed by the reaction of dinaphthylether.     

Development of a catalytic cracking process for converting waste plastics to petrochemicals

The catalytic degradation of polyolefin using H-gallosilicates was examined using a bench-scale reactor (0.8kg/h) with semicontinuous feeding and the following plastics: (1) low-density polyethylene (LDPE) pellets; (2) linear low-density polyethylene (L-LDPE) pellets; (3) high-density polyethylene (HDPE) pellets; (4) polypropylene (PP) pellets; (5) polyolefin obtained from pulverized industrial waste plastics. The yields of liquid compounds from these materials, which were aromatics in most cases, ranged from 55wt% to 68wt%. With an increase in the ratio of total reactant to catalyst, the liquid yield remained the same. Yields of benzene, toluene, and xylenes (BTXs) decreased rapidly to below 50wt% at a ratio of more than 30. Differences in this ratio for BTXs were always small and were independent of the material. Only about half of the gas product was propane with a fresh catalyst. When the experiments were repeated, propylene, isobutane, and isobutene were found to increase.     

Enzymatic degradation of poly([R,S] β-hydroxybutyrate)

The synthetic analogue of a bacterially produced polyester, poly(-hydroxybutyrate) (PHB) was synthesized from racemic -butyrolactone using anin situ trimethyl aluminum-water catalyst. The polymer was fractionated into samples differing in molecular weight and isotactic diad content. The latter was closely related to degree of crystallinity. The biodegradation of these fractions were examined by monitoring mass loss over time in the presence of anAlcaligenes faecalis T1 extracellular bacterial poly(-hydroxybutyrate) depolymerase. The fraction with high isotactic diad tacticity content showed little or no degradation over a 50 hour incubation period, whereas the fraction of intermediate isotactic diad content degraded in a continuous steady fashion at a rate that was less than that for bacterial PHB. The low isotactic diad fraction underwent a rapid initial degradation, followed by no further mass loss. The presence of stereoblocks in the polymer structure of the various fractions was an influence on the degree of susceptibility towards degradation and is related to sample crystallinity.     

Study of Trace and Heavy Metals in Rural and Urban Aerosols of Uludağ and Bursa (Turkey)

The concentrations of heavy, trace elements and major ions measuredin the Uluda and Bursa aerosols were investigated to assess size distributions, spatial and temporal variability, sources and source regions affecting the composition of aerosols in Uluda and Bursa. A total of 81 samples were collected in two sites, one in Bursa city and another in the Uluda Mountain during two sampling campaigns. Daily samples were collected using a high volume sampler on Whatman 41 cellulose filters in Uluda, while three days interval samples were collected in Bursa using an automatic dichotomous sampler on PTFE Teflon filters. Samples were analysed for 15 trace and heavy metals (Al, Fe, Ba, Na, Mg, K, Mn, Ca, Cu), (V, Pb, Cd, Cr, Ni, Zn), and 4 major ions (SO₄ ^2-, NO₃ ^-, Cl^-), (NH₄ ⁺) using ICP-AES, GFAAS, HPLC and UV/VIS Spectrophotometer,respectively. In general, concentrations of the metals measured inUluda aerosols were lower than those in Bursa. The concentrations of crustal elements were higher in summer than winter, while anthropogenic elements had higher concentrations in winter than summer. Most of the mass of crustal elements was concentrated in the coarse mode while the mass of the heavy metals was concentrated in the fine mode. Factor analysis revealed four factors with sources including crustal, industrial and combustion. Back trajectory calculations were used to determine long range contributions. These calculations showed that contributions were mostly from European countries, former Soviet Union countries, Black Sea and North Africa.     

Soil Respiration in Relation to Small-Scale Patterns of Lead and Mercury in Mor Layers of Southern Swedish Forest Sites

Pollution-related lead (Pb) andmercury (Hg) in mor layers of Southern Swedenmight have effects on soil biology, although inthe literature effect concentrations have beenidentified at much higher levels. Considerablesmall-scale spatial variability in heavy metalcontents and microbial respiration in mor layersof forest sites was used to calculatecorrelations that could reveal toxic effects.Negative correlations were always strongest atsites with high loads of Pb or Hg, which was considered to indicate metal toxicity. The highload sites were found in Southwestern Sweden,locally at a motorway and at a chlorine-alkalifactory. Other factors of possible influence,such as other pollutants, age of organic materialor climatic differences, would affect high andlow load sites alike. Negative correlations withrespiration were found for Pb at sites with 74 g g^-1 of mean Pb content in O_f-layer and for Hg at 0.25 g g^-1.     

Pore structure and adsorption properties of activated carbon prepared from granular molded waste paper

We have previously manufactured activated carbon using waste paper board, which was prepared by adding 8% phenol resin adhesive to torn waste newspaper and hot-pressing. In this study, the pretreatment process of the raw material was simplified; the waste paper was extruded to form granules. The activated carbon was manufactured by the carbon dioxide activation method using the granules as the raw material. The properties of the activated carbon were evaluated based on the pore structure, the iodine adsorption number, and the adsorption of toluene vapor in a sealed chamber. The activated carbon, which was manufactured at an activation temperature of 1100°C and a treatment time of 60min, exhibited a specific surface area of 1241m²/g and an iodine adsorption number of 1120mg/g. These results were similar to those obtained for two commercially available activated carbons. The extent of toluene vapor adsorption by this activated carbon was similar to that observed for the two commercial activated carbons over a period of 130min.     

Catalytic decomposition of hydrocarbon into hydrogen and carbon in a spouted-bed reactor as the second-stage reactor of a plastic recycling process

A two-stage process for the chemical recycling of plastics is proposed. In this process, which consists of two reactors, plastics are converted into hydrogen and carbon. In the first reactor, plastic chips are thermally decomposed into hydrocarbons. In the second reactor, the hydrocarbons formed in the first reactor are catalytically decomposed into carbon and hydrogen. In this study, in order to obtain basic data for the second reactor, propene was catalytically decomposed in a laboratory-scale spouted-bed reactor (600mm high, 21.6mm internal diameter, made of SUS304). The effect of the type of spouting medium used on the decomposition behavior of propene was investigated using four types of spouting medium (nickel-plated -alumina, palladium-plated -alumina, nickel-impregnated -alumina, and -alumina). The nickel-impregnated -alumina gave the best propene conversion and hydrogen yield.     

Effect of Starch Granule Size on Viscosity of Starch-Filled Poly(hydroxy ester ether) Composites

The effect of starch granule size on the viscosity of starch-filled poly(hydroxy ester ether) (PHEE) composites was characterized using size-fractionated potato starch, as well as unfractionated starches (rice, corn, wheat, and potato). Potato starch was separated using an air classifier into four particle size fractions: <18 m, 18-24 m, 24-30 m, and >30 m. The starch was dried to a moisture content of 0.5% to minimize moisture effects on composite rheology. PHEE and potato starch were extruded with starch volume fractions of 0.46 and 0.66. Stress relaxation, frequency and strain sweep, and temperature-dependence measurements were carried out. Although small variations in viscosity were seen with the different potato starch fractions, differences were not significant at a volume fraction of 0.46. Viscosity differences between the different particle size fractions were more pronounced at a volume fraction of 0.66. The temperature dependence could be described by an Arrhenius relation, with an apparent activation energy of 84 kJ/mole. At a volume fraction of 0.46, the starch/PHEE viscosities increased in the order potato starch < wheat starch corn starch < rice starch.     

In situ bioremediation of a hydrocarbon polluted site with cyclodextrin as a coadjuvant to increase bioavailability

Bioavailability is one main factor that influences the extent of biodegradation of hydrocarbons. They are very poorly soluble in water and easily adsorbed to clay or humus fractions, so they pass very slowly to the aqueous phase where they are metabolised by microorganisms. Cyclodextrins are natural compounds that form soluble inclusion complexes with hydrophobic molecules and increase degradation rate of hydrocarbons in vitro. In the perspective of an in situ application, we previously checked that -cyclodextrin does not increase eluviation of hydrocarbons through the soil and consequently does not increase the risk of groundwater pollution. The results of an in situ application of -cyclodextrin for bioremediation of a hydrocarbon polluted site are presented. We stated that the combination of bioaugmentation and enhanced bioavailability due to -cyclodextrin was effective for a full degradation.     

Modelling Easily Biodegradability of Materials in Liquid Medium-Relationship Between Structure and Biodegradability

In the present project, twenty materials (e.g., polyhydroxybutyrate-hydroxyvalerate, polycaprolactone, cellulose acetate, polyacticacid, polyethylene), representing varied biodegradability levels were studied. An aerobic respirometric test, based on the CEN Draft, was setup. The biodegradability of each plastic film was evaluated by measuring the percentage of carbon converted into CO₂ during 35 days. The values of the CO₂ production were plotted versus days as a cumulative function. In order to reduce its number of points, the cumulative curve was modeled using a sigmoïd function (Hill sigmoïd). This model was compared to one found in the literature. A _i ² test showed that the biodegradation curve was more accurately fitted with the model than the previous one. Three kinetic parameters were determined by this Hill model: one represents the maximal percentage of carbon converted into CO₂, the second the half-life time in days of the degrading part of the material and the third one the curve radius.In addition, the following analyses were carried out on each sample: elemental analysis, thickness, hydrophobicity and surface free energy measurements. In order to compress the information and to keep only relevant pieces, these parameters were submitted to a Principal Component Analysis. PCA found linear combinations of variables that describe major trends in the data. The two principal components which separate groups of materials were closely related to a chemical and a physical axis respectively. Materials showing a high biodegradability were related to high oxygen (and nitrogen) contents and low hydrophobicity: Material thickness did not influence the likeliness to biodegradability described by the maximum biodegradation rate. Finally, this study established the correlation between the biodegradation and the structure of biopolymers.     

Thermal cracking of oils from waste plastics

Thermal cracking of decomposed waste plastic oil produces a good yield of olefins. The solvent extraction of such waste plastic oil seems to be efficient for increasing gas yields and recycling monomers. To assess the potential of monomer recovery from municipal waste plastics, the oils were cracked using a laboratory-scale quartz-tube reactor. The waste plastic oils were provided by two commercial plants of the Sapporo Plastic Recycle Co. and the Dohoh Recycle Center Co. in Japan. A model waste plastic oil made in a laboratory was also examined. Yields of ethene, propene, and other products were measured at different temperatures. Two-step pyrolysis reduces coking compared with the direct thermal degradation of plastics. The raffinates from waste plastic oils extracted by sulfolane were also cracked. The primary products were almost the same as those from nontreated oils. The maximum total gas yield was 78wt%–85wt% at 750°C, an increase of about 20wt% compared with that of nonextracted oil. Solvent extraction removes stable aromatic hydrocarbons such as styrene, which is more coked than cracked.