Removing perfluorooctane sulfonate and perfluorooctanoic acid from solid matrices, paper, fabrics, and sand by mineral acid suppression and supercritical carbon dioxide extraction

The removal of perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) from solid matrices has received considerable attention because of the environmental persistence, bioaccumulation, and potential toxicity of these compounds. This study presents a simple method using concentrated HNO₃ as a suppression agent, and methanol-modified supercritical carbon dioxide (Sc-CO₂) extraction for removing PFOS and PFOA from solid matrices. The optimal conditions were 16 M HNO₃ and 20% (v/v) methanol containing Sc-CO₂, under a pressure of 20.3 MPa and a temperature of 50 °C. Extraction time was set at 70 min (40 min for static and 30 min for dynamic extraction). PFOA and PFOS were identified and quantitated by liquid chromatography/mass spectrometry. The extraction efficiencies (with double extractions) were close to 100% for PFOA and 80% for PFOS for both paper and fabric matrices. The extraction efficiencies for sand were approximately 77% for PFOA and 59% for PFOS. The results show that this method is accurate, and effective, and that it provides a promising and convenient approach to remediate the environment of hazardous PFOA and PFOS contamination.     

Formation of organochlorine by-products in bleached laundry

Laundering fabrics with chlorine bleach plays a role in health and hygiene as well as aesthetics. However, laundry bleaching may create chlorinated by-products with potentially adverse human health effects. Studies have shown that toxic chlorinated gases are produced in the headspace of washing machines when hypochlorite-containing bleach is used. Laundry bleaching has also been implicated in contributing dissolved organochlorine to municipal wastewater. However, there have been no reports of organochlorines produced and retained in fabric as a result of laundry bleaching. We have used a chlorine-specific X-ray spectroscopic analysis to demonstrate the formation of organochlorine by-products in cotton fabrics laundered with chlorine bleach under typical household conditions. Organochlorine formation increases at higher wash temperature. At least two pools of organochlorine are produced in bleached fabric: a labile fraction that diminishes over several months of storage time as well as a more stable fraction that persists after more than 1 year. Our results also suggest that residual hypochlorite remains in fabric after laundering with bleach, presenting the possibility of direct and sustained dermal contact with reactive chlorine. This study provides a first step toward identifying a new risk factor for elevated organochlorine body burdens in humans.     

Perfluorooctane surfactants in waste waters, the major source of river pollution

Perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) are persistent and widely distributed in the environment. Recently, the discharge of municipal waste water has been shown to be an important route of such perfluoroalkyl surfactants into the aquatic environment. The aim of this study was to assess the mass flow of PFOA and PFOS from typical waste water treatment plants (WWTPs) into surface waters. Samples were collected at different stages of treatment of four WWTPs in Northern Bavaria, Germany, and from the rivers receiving the treated waste waters (WW). The outflow of PFOA from the WWTPs to the rivers was 20-fold higher than the inflow to the plants; about a tenth was removed with the sludge. For PFOS, the increase from inlet to outlet was about 3-fold; almost half of it was retained in the sludge. Both surfactants were released into river water from the WWTP of a medium-sized city with domestic, industrial and commercial waste waters; in domestic waste waters the surfactants were found at much lower levels.     

城市生活垃圾中纤维素含量测定方法优化

对传统硫酸法进行改进,建立适用于城市生活垃圾纤维素含量的测定方法。以脂肪抽提时间、硫酸浓度、水解反应温度、水解反应时间、稀释硫酸浓度、回流时间为考察因素进行6因素5水平正交实验。结果表明,测定纤维素含量的最佳条件为：脂肪抽提时间4h、硫酸浓度70％、水解反应温度30℃、水解反应时间5h、稀释硫酸浓度5％、回流时间3h。优化后纤维素测定条件RSD均小于1．69％,平均回收率98．76％,表明该方法的精度高,可靠行强。     

Enzyme hydrolysis of polyester knitted fabric: A method to control the microfiber shedding from synthetic textile

Synthetic textile materials are noted as one of the major contributors to microfiber release from household laundry. The higher usage of synthetic textiles was noted as one of the major reasons for the leaching of microfibers into the aquatic system. Though few laundry aids are available to control the release of microfiber from laundry, no successful methods were developed to control it in the fabric itself. Hence, this research aimed to analyze the effectiveness of surface modification of polyester fabric using lipase enzyme and its impact on microfiber shedding. Taguchi’s L9 orthogonal array was adopted to optimize the enzyme treatment process parameters to reduce microfiber shedding. The results showed that enzyme concentration was the major influencing factor with a contribution of 35.56%, followed by treatment pH (35.247%), treatment time (17.46%), and treatment temperature (11.74%). The optimization with S/N ratio showed minimum microfiber shedding at an enzyme concentration of 0.5 gram per liter (gpl), treatment temperature of 55°C, 6.5 pH, and a treatment time of 45 minutes. Knitted polyester fabric treated with the optimized enzyme treatment condition showed a significant reduction (p<0.05) in microfiber shedding (count—79.11% and mass—85.68%). The surface changes and the interaction of the enzyme on the fabric were confirmed by hydrolytic activity and FTIR analysis. The optimized treatment on different knit structures and fabric with different grams per square meter (GSM) indicated the versatility of the treatment irrespective of fabric parameters. The repeated laundry process (20 washing cycles) showed that the enzyme-treated samples had a significant level (p<0.05) of reduction in shedding than the control sample. The difference in shedding after 20 washes supports the efficiency and longevity of the enzyme treatment process in reducing microfiber shedding.

     

Perfluorooctanesulfonate and perfluorooctanoate in raw and treated tap water from Osaka, Japan

Perfluorooctanesulfonate (PFOS) and perfluorooctanoate (PFOA) have been recognized as emerging environmental pollutants because of their ubiquitous occurrence in the environment, biota, and humans. PFOS and PFOA have been detected in water in Japan. Nevertheless, occurrence of PFOS and PFOA in potable water from municipal water treatment plants is not clearly known. We analyzed PFOS and PFOA in raw and tap water samples collected from 14 drinking water treatment plants in winter and summer seasons in Osaka to determine the concentrations of PFOS and PFOA in raw and potable tap water samples. PFOS and PFOA were detected in all raw water samples. Concentration ranges of PFOS and PFOA in raw water were 0.26-22 ng/l and 5.2-92 ng/l, respectively. Whereas the concentrations PFOS in raw water from Osaka were similar to those in other areas in Japan, the concentrations of PFOA were higher than in other areas. Concentration ranges of PFOS and PFOA in potable tap water were 0.16-22 ng/l and 2.3-84 ng/l, respectively. There were positive correlations between PFC concentrations in raw water and tap water samples. Therefore, the removal efficiency of PFCs by the present water treatment may be low. Based on the current action value reported by U.S. Environmental Protection Agency, PFOA concentrations found in tap water in Osaka is not expected to pose health risks.     

Survey of perfluorinated alkyl acids in Finnish effluents, storm water, landfill leachate and sludge

The objective of the Control of Hazardous Substances in the Baltic Sea (COHIBA) project is to support the implementation of the HELCOM Baltic Sea Action Plan regarding hazardous substances by developing joint actions to achieve the goal of “a Baltic Sea with life undisturbed by hazardous substances”. One aim in the project was to identify the most important sources of 11 hazardous substances of special concern in the Baltic Sea. Among them are perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA). In this study, four perfluorinated alkyl acids (PFAAs) were studied: PFOA, PFOS, perfluorohexanoic acid (PFHxA) and perfluorodecanoic acid (PFDA). The occurrence of PFAAs in municipal and industrial wastewater treatment plant effluents (MWWTP1-3, IWWTP1), target industry effluent, storm water, landfill leachate and sludge was studied. Effluents were analysed six times and storm water, leachate and sludge were analysed twice, once in the warm season and once in the cold, during a 1-year sampling campaign. PFOS prevailed in two municipal effluents (MWWTP1 and 3) and industrial effluent (IWWTP1; 7.8–14, 8.0–640 and 320–1,300 ng/l, respectively). However, in one municipal effluent (MWWTP2) PFOA was, in a majority of sampling occasions, the predominant PFAA (9–15 ng/l) followed by PFOS (3.8–20 ng/l). The highest PFAA loads of the municipal effluents were found in the MWWTP3 receiving the biggest portion of industrial wastewater. In storm water the highest concentration was found for PFHxA (17 ng/l). The highest concentration of PFOS and PFOA were 9.9 and 5.1 ng/l, respectively. PFOS, PFOA and PFHxA were detected in every effluent, storm water and landfill leachate sample, whereas PFDA was detected in most of the samples (77 %). In the target industry, PFOS concentrations varied between 1,400 and 18,000 μg/l. In addition, on one sampling occasion PFOA and PFHxA were found (0.027 and 0.009 μg/l, respectively). For effluents, PFAA mass flows into the Baltic Sea were calculated. For municipal wastewater treatment plants average mass flows per day varied for PFOS between 1,073 and 38,880 mg/day, for PFOA 960 and 2,700 mg/day, for PFHxA 408 and 1,269 mg/day and for PFDA 84 and 270 mg/day. In IWWTP mass flows for PFOS, PFOA, PFHxA and PFDA were 495 mg/d, 28 mg/d, 23 mg/d and 0.6 mg/g, respectively.     

Effect of the temperature and the exclusion of UVB radiation on the phenolics and iridoids in Menyanthes trifoliata L. leaves in the subarctic

The long-term effects of UVB exclusion and temperature on the methanol extractable (ME) phenolics (flavonoids, phenolic acids) and iridoids of Menyanthes trifoliata L. (Mt) leaves were studied in northern Finland (68°N) using wooden frames covered with filters for UVB exclusion (polyester filter), control (cellulose acetate filter) and ambient (no filter) conditions. Analysis of ambient plots showed no effect of the daily mean temperature (2σ = 1.58 °C) on the leaf ME compound content and composition, but minimum temperatures decreased the flavonol content. UVB exclusion did not affect the total ME compound content but significantly decreased the proportion of flavonols concomitantly with an increase in iridoids. Due to its high iridoid content, Mt appears as an interesting model plant for studying the iridoid biosynthesis and its regulation under stress conditions.     

Perfluorooctanoic acid and perfluorooctane sulfonate released from a waste water treatment plant in Bavaria, Germany

Purpose

Perfluorooctanoate (PFOA), perfluorooctane sulfonate (PFOS), and precursors and derivatives thereof have been employed as surfactants and anti-adhesives. PFOA and PFOS are environmentally persistent and the discharge of municipal waste waters is one of the principal routes of these compounds into the aquatic environment. In a previous study, the concentrations of PFOA and PFOS in grab samples collected from the waste water treatment plant (WWTP) of Bayreuth, a city of 72,000 inhabitants in Bavaria, Germany, during two periods showed considerable variability. For a better estimate of average mass flows, the surfactants were monitored (five samplings) from 16 March to 18 May 2007. In a second campaign, river water receiving the WWTP effluent was sampled twice a day for five consecutive days.

Methods

Quantitative analysis was done by stable-isotope dilution, pre-cleaning, and pre-concentration by solid-phase extraction, and liquid chromatography followed by electrospray ionization/tandem mass spectrometry.

Results

The mass flows of PFOA and PFOS through the WWTP were determined. PFOA is fully discharged into the river, while about half of PFOS is retained in the sewage sludge. The average daily mass load of the river Roter Main by the WWTP of Bayreuth is about 1.2?±?0.5 g PFOA and 5?±?2 g PFOS, with variations of up to 140% within one day.

Conclusion

Overall, the total annual release to the rivers of Germany may be in the range of several hundred kilograms of PFOA and several tons of PFOS.     

Perfluoroalkyl compounds in municipal WWTPs in Tianjin, China—concentrations, distribution and mass flow

BACKGROUNDS: Perfluorinated compounds (PFCs) have drawn much attention due to their environmental persistence, ubiquitous existence, and bioaccumulation potential. Wastewater treatment plants (WWTPs) are fundamental utilities in cities, playing an important role in preventing water pollution by lowering pollution load in waste waters. However, some of the emerging organic pollutants, like PFCs cannot be efficiently removed by traditional biological technologies in WWTPs, and some even increase in effluents compared to influents due to the incomplete degradation of precursors. Hence, WWTPs are considered to be a main point source in cities for PFCs that enter the aquatic environment. However, the mass flow of PFCs from WWTPs has seldom been analyzed for a whole city. Hence, in the present study, 11 PFCs including series of perfluoroalkyl carboxylic acids (PFCAs, C4-C12) and two perfluoroalkyl sulfonates (PFASs, C6 and C8) were measured in WWTP influents and effluents and sludge samples from six municipal WWTPs in Tianjin, China. Generation and dissipation of the target PFCs during wastewater treatment process and their mass flow in effluents were discussed. RESULTS: All the target PFCs were detected in the six WWTPs, and the total PFC concentration in different WWTPs was highly influenced by the population density and commercial activities of the corresponding catchments. Perfluorooctanoic acid (PFOA) was the predominant PFC in water phase, with concentrations ranging from 20 to 170 ng/L in influents and from 30 to 145 ng/L in effluents. Concentrations of perfluoroalkyl sulfonates decreased substantially in the effluent compared to the influent, which could be attributed to the sorption onto sludge, whereas concentrations of PFOA and some other PFCAs increased in the effluent in some WWTPs due to their weaker sorption onto solids and the incomplete degradation of precursors. Perfluorooctane sulfonic acid (PFOS) was the predominant PFC in sludge samples followed by PFOA, and their concentrations ranged from 42 to 169 g/kg and from 12 to 68 g/kg, respectively. Sludge-wastewater distribution coefficients (log K(d)) ranged from 0.62 to 3.87 L/kg, increasing with carbon chain length of the homologues. The mass flow of some PFCs in the effluent was calculated, and the total mass flow from all the six municipal WWTPs in Tianjin was 26, 47, and 3.5 kg/year for perfluorohexanoic acid, PFOA, and PFOS, respectively.     

PCDDs, PCDFs emission control by dry scrubbing system

Presently, in Japan there are no limitations on the emission of PCDDs or PCDFs, but in order to study the feasibility of dry type air pollution control, a pilot plant was constructed in 1988 and the removal efficiencies for PCDDs, acid gas and heavy metals were measured.At the same time PCDDs concentration was compared with that of a previously installed electrostatic precipitator (ESP) plus wet scrubber line.In this paper, the following two items are reported.

1. (1) The difference in the amounts of PCDDs and PCDFs produced due to differences in gas temperature and retention time in ESP and fabric filter (FF).

2. (2) Removal efficiencies of PCDDs and PCDFs of fabric filter.

PCDDs concentration, generally 100–200 ng/Nm³ at the boiler outlet (ESP inlet and/or Quench Reactor (QR) inlet), increased several times at the ESP outlet, but it showed almost no increase at the QR outlet due to a sudden temperature drop. The temperature was 280–310°C, and the gas retention time was 12 sec. during passage through ESP so that it is thought that PCDD was formed under these conditions.On the other hand, a removal efficiency of approx. 90% was obtained with the fabric filter, and the PCDD at the bag outlet was at a sufficiently low level.     

PTFE-coated non-stick cookware and toxicity concerns: a perspective

PTFE is used as an inner coating material in non-stick cookware. This unique polymer coating prevents food from sticking in the pans during the cooking process. Such cookware is also easy to wash. At normal cooking temperatures, PTFE-coated cookware releases various gases and chemicals that present mild to severe toxicity. Only few studies describe the toxicity of PTFE but without solid conclusions. The toxicity and fate of ingested PTFE coatings are also not understood. Moreover, the emerging, persistent, and well-known toxic environmental pollutant PFOA is also used in the synthesis of PTFA. There are some reports where PFOA was detected in the gas phase released from the cooking utensils under normal cooking temperatures. Due to toxicity concerns, PFOA has been replaced with other chemicals such as GenX, but these new alternatives are also suspected to have similar toxicity. Therefore, more extensive and systematic research efforts are required to respond the prevailing dogma about human exposure and toxic effects to PTFE, PFOA, and GenX and other alternatives.     

PAFC对水体中持久性有机污染物PFOA的混凝效果

针对含全氟辛酸(PFOA)的工业废水及应对PFOA的污染突发事件,采用PAFC及其复配粘土矿物凹凸棒和沸石进行混凝实验,并对几个影响因素进行了考察。结果表明,在PAFC的最佳投加量10 mg/L时,PFOA和浊度的去除率分别达到70.25%和99.42%,PAFC混凝处理PFOA的效果优于PAC;pH值对PAFC去除PFOA有一定的影响,当pH大于6时有利于PFOA的去除;PFOA和浊度的去除率随原始浊度的增加而增加;活性炭、盐酸改性凹凸棒、盐酸改性沸石、CT-MAB改性的沸石复配PAFC均可提高PFOA的去除率;改性处理后的沸石应用于PFOA的处理中,有望降低处理成本。     

Formation of PFOA from 8:2 FTOH in closed-bottle experiments with brackish water

The formation of perfluorooctanoate (PFOA) from 1H,1H,2H,2H-perfluorodecanol (8:2 FTOH) was studied for the first time in laboratory experiments with brackish water. The water samples were collected from the Baltic Sea, which is one of the largest brackish water areas in the world and is polluted with PFOA and other perfluorinated compounds. The formation of PFOA was studied in closed-bottle experiments at different water temperatures. As a reference experiment, a modified OECD 310 test was conducted with sludge from a wastewater treatment plant and with brackish water. The PFOA and 8:2 FTOH were concentrated from water samples by solid-phase extraction (SPE) and were analysed using liquid chromatography–mass spectrometry. The effect of oxygen concentration on the formation of PFOA was studied using surface water samples with high and low oxygen contents. Other experiments were performed with oxygen-rich surface water and oxygen-deficient bottom water. The formation of PFOA was observed in all experiments; it was higher in the trial performed with brackish water than in the reference test carried out with sludge. Clear temperature dependence was observed in the formation of PFOA in brackish water tests; after a 30-day test period, a sixfold increase was observed in the amount of PFOA in surface water between the temperatures of 15 and 20 °C. Microbes were suggested as the major cause of the formation of PFOA, but other environmental characteristics, such as oxygen, could also affect the formation potential of PFOA.     

基于生态安全的DAT-IAT城市污水处理工艺改进研究

通过正交试验,得到了DAT-IAT工艺和A/DAT-IAT工艺处理城市污水的常规指标去除和生态毒理指标削减的最优运行条件。结果表明,在正交试验的同一工艺中,COD去除最优运行条件的出水COD值优于生态毒性削减最优运行条件的出水COD值,但前者出水的生态毒性较大。由于厌氧池的水解酸化作用,A/DAT-IAT工艺对COD和生态毒性的处理效果均优于DAT-IAT工艺,并且回流总能耗低于DAT-IAT工艺,但是出水COD仍不达标。为了降低进入工艺的COD的总量,以絮凝沉淀做为预处理工艺,并采用Al残留量最小的絮凝剂投药量以降低出水中残留Al带来的生态风险。结果表明,在COD去除最优运行条件下,具有絮凝预处理的工艺对COD的去除效果优于没有絮凝预处理的工艺。絮凝-A/DAT-IAT工艺在COD去除最优运行条件下出水COD为104.46 mg/L,满足排放标准。在毒性削减最优运行条件下,具有絮凝预处理的工艺的出水生态毒性有所上升,但是污染物的总量得到了大幅削减。絮凝-A/DAT-IAT工艺与DAT-IAT工艺相比,在污染物去除效率得到大幅增加的同时,生态毒性得到有效控制,生态安全得到了有效的保障。     

无机陶瓷纳滤膜分离高钠盐废水中的锶

本实验研究表明,仅用截留分子量为1000的无机陶瓷纳滤膜分离高钠盐模拟溶液中的锶,分离效果并不理想.为提高陶瓷纳滤膜对锶的选择分离效果,选择了分子量为3000的聚丙烯酸作为陶瓷纳滤膜分离的强化剂,重点探讨了溶液pH值、聚丙烯酸浓度、温度及离子强度对模拟溶液盐分离效果和膜通量的影响,并得到了适宜的锶钠分离条件.实验结果表明,在适宜条件下,通过聚丙烯酸强化和两级分离,陶瓷纳滤膜可大大提高模拟溶液中锶离子的选择分离效果,锶/钠的分离因子高达205.     

Laboratory evaluation of thermophilic-anaerobic digestion to produce Class A biosolids. 1. Stabilization performance of a continuous-flow reactor at low residence time.

There is increasing interest in the United States in producing biosolids from municipal wastewater treatment that meet the criteria for Class A designation established by the U.S. Environmental Protection Agency. Class A biosolids are intended to be free of pathogens and also must meet requirements for reduction of the vector-attraction potential associated with untreated sludge. High-temperature processes are considered to produce Class A biosolids if the combination of operating temperature and treatment time exceeds minimum criteria, but this option is not applicable to mixed, continuous-flow reactors. Such reactors, or any combination of reactors that does not meet the holding time requirement at a specific temperature, must be demonstrated to inactivate pathogens to levels consistent with the Class A criteria. This study was designed to evaluate pathogen inactivation by thermophilic anaerobic digestion in a mixed, continuous-flow reactor followed by batch or plug-flow treatment. In this first of a two-part series, we describe the performance of a continuous-flow laboratory reactor with respect to physical and chemical operating parameters; microbial inactivation in the combined continuous-flow and batch treatment system is described in the second part. Sludges from three different sources were treated at 53 degrees C, while sludge from one of the sources was also treated at 55 and 51 degrees C. Relatively short hydraulic retention times (four to six days) were used to represent a conservative operating condition with respect to pathogen inactivation. Treatment of a fermented primary sludge led to an average volatile-solids (VS) destruction efficiency of 45%, while VS destruction for the other two sources was near or below 38%, the Class A criterion for vector attraction reduction. Consistent with other studies on thermophilic anaerobic digestion of sludges at short residence times, effluent concentrations of volatile fatty acids (VFAs) were relatively high. Also consistent with other studies, the most abundant VFA in the effluent was propionate. Gas production ranged from 0.3 to 0.5 m3/kg VS fed and from 0.8 to 1.3 m3/kg VS destroyed.     

PCDD/PCDF Isomer patterns in waste incinerator flyash and desorbed into the gas phase in relation to temperature

The influence of temperature on the PCDD and PCDF isomer profiles of a municipal waste incinerator flyash and the PCDD/PCDF desorbed from the ash under an inert atmosphere was investigated using a bench-scale reactor. Exposure to temperatures of 250 degrees C and above resulted in significant changes in the distribution of isomers within most dioxin and furan congener groups. The PCDD content tended to become more evenly distributed across the range of isomers than was the case for the raw flyash, while the PCDF content became concentrated across a relatively lower number of isomers. In most cases the desorbed PCDD/PCDF were mainly mono- to tri-chlorinated, and hence had a relatively low I-TEQ value. The isomer profiles of the desorbed species were also influenced by temperature. There were some significant differences between the PCDF isomer profiles of the desorbed species and those of the treated flyashes under the same conditions, but no clear differences between the PCDD isomer profiles.     

Characterizing perfluorooctanoate in ambient air near the fence line of a manufacturing facility: comparing modeled and monitored values

In order to improve our understanding of the nature, measurement and prediction of salts of perfluorooctanoic acid (PFOA) in air, two studies were performed along the fence line of a fluoropolymer manufacturing facility. First, a six-event, 24-hr monitoring series was performed around the fence line using the OSHA versatile sampler (OVS) system. Perfluorooctanoate concentrations were determined as perfluorooctanoic acid (PFOA) via liquid chromatography and mass spectrometry. Those data indicated that the majority of the PFOA was present as a particulate. No vapor-phase PFOA was detected above a detection limit of approximately 0.07 microg/m3. A follow-up study using a high-volume cascade impactor verified the range of concentrations observed in the OVS data. Both studies aligned with the major transport direction and range of concentrations predicted by an air dispersion model, demonstrating that model predictions agreed with monitoring results. Results from both monitoring methods and predictions from air dispersion modeling showed the primary direction of transport for PFOA was in the prevailing wind direction. The PFOA concentration measured at the site fence over the 10-week sampling period ranged from 0.12 to 0.9 microg/m3. Modeled predictions for the same time period ranged from 0.12 to 3.84 microg/m3. Less than 6% of the particles were larger than 4 microm in size, while almost 60% of the particles were below 0.3 microm. These studies are believed to be the first published ambient air data for PFOA in the environment surrounding a manufacturing facility.     

Low-heat alkaline pretreatment of biomass for dairy anaerobic codigestion

In this research, low-heat alkaline pretreatment was evaluated to determine the extent to which urban landscape waste (yard waste), corn stover, and switchgrass could be codigested under conditions typical of US farm-based anaerobic digestion (AD). Waste heat from combined heat and power (CHP) units associated with AD could make such pretreatment economical. Short-term batch digestion studies and 8-week continuous-feed studies were used to screen and evaluate various pretreatment conditions. Results indicate that maple and oak leaves did not digest well, even with pretreatment. Pretreatment did improve digestion of corn leaves and stalks as well as switchgrass. However, these materials also digested reasonably well even without pretreatment. No digester operational problems were observed during continuous-feed studies of intermittently stirred bench top digesters, but optimal levels of alkali, temperature, and pretreatment time may be specific to the feedstock, particle size, and digester loading rate. Results suggest that some common lignocellulosic biomass materials, such as corn stover and switchgrass, could be successfully codigested in many existing farm-based digesters. Interestingly, without pretreatment, switchgrass digestion improved over 20-fold when digested with seed culture from a dairy digester compared to seed culture from a municipal digester, suggesting that culture acclimation could be as important as pretreatment in improving digestion of specific lignocellulosic feedstocks.