Ti-Ni/γ-Al_2O_3粒子电极的制备及其处理氯霉素废水的效果

以活性氧化铝(γ-Al_2O_3)为载体,Ti、Ni为负载金属,采用溶胶凝胶法制备复合型Ti-Ni/γ-Al_2O_3粒子电极,并用其电催化处理模拟氯霉素废水。考察了Ti和Ni负载组分比例、负载次数、电流强度、pH、电极板间距等因素对氯霉素降解效果的影响。结果表明,Ni∶Ti摩尔比为1∶10、负载2次制备的复合型Ti-Ni/γ-Al_2O_3粒子电极电催化效果最好,在电流强度为0.09A、pH为4、电极间距为40mm的优化电解条件下,氯霉素去除率可高达80.56%。     

模拟太阳光协同三维电极/电Fenton降解甲基橙

以TiO_2纳米管为阳极、石墨电极为阴极、泡沫镍颗粒为粒子电极组成新型的模拟太阳光协同三维电极/电Fenton(3D/SPEF)体系降解甲基橙。研究了该体系的协同处理效果,以及该体系降解甲基橙的影响因素和反应动力学。结果表明:模拟太阳光与3D/EF体系光电催化联合处理表现出良好的协同效应,其处理能耗仅为3D/EF的9/16;协同体系降解甲基橙过程的表观反应动力学总级数为0.97;通过单因素实验确定协同体系最优反应条件为:电压为15 V、初始p H为7、甲基橙初始浓度为50 mg/L、Fe~(2+)投加量为1 mmol/L,甲基橙的去除率达到93.77%,3D/SPEF体系在中性条件更有利于甲基橙的降解,克服了常规三维电极/电Fenton一般只能在酸性条件下进行的不足。     

平板炭气凝胶电极电吸附除氟

采用自制的炭气凝胶平板电极进行模拟水样中氟的电吸附去除研究,通过单因子实验优化了该电吸附技术的操作参数和适用的溶液条件,并研究了反接电极法的再生效果。研究结果表明,自制的炭气凝胶平板由纳米颗粒组成三维网络结构,比表面积为670.90 m2/g,具有良好的充放电可逆性和迅速形成表面双电层的特点。静态电吸附除氟效果最佳的条件为:水样氟离子浓度6 mg/L,pH 7.0,极板间距4 cm,电压1.6 V;共存物质硝酸根、腐殖酸、碳酸根和碳酸氢根等对氟离子的电吸附具有一定的促进作用。吸附氟离子后的炭气凝胶材料的比表面、孔体积、电容值有所减小。对于吸附氟离子后的炭气凝胶平板电极,采用反接电极法取得较好再生效果的条件为:流动状态、电压1.6 V、极板间距4 cm。再生后的炭气凝胶电极与原始炭气凝胶相比,依然具有良好的充放电可逆性。     

RuO_2-IrO_2/Ti阳极电催化降解偶氮染料甲基橙模拟废水

以自制Ti基Ru O2-Ir O2镀层形稳电极为阳极,采用电催化氧化处理偶氮染料甲基橙模拟废水。以硫酸钠为支持电解质,在自然p H条件下分别考察了电解时间、电极间距、电流密度和电解质浓度等因素对甲基橙去除率的影响,并分析其原因。实验结果表明,在自然p H、电极间距为1.0 cm、电流密度为30.0 m A/cm2、电解质硫酸钠浓度为20.0 g/L、电解1.0h,甲基橙去除率高达90.0%以上。因此,电催化氧化法作为一种高效、简便的染料废水处理技术,具有一定的应用潜力。     

软锰矿粒子电极的制备及其对SMP的催化降解

针对二氧化锰对废水中氯离子电解生成活性氯具有较好催化活性的特点,以软锰矿为原料制备一种新型粒子电极,将其用于三维电极系统处理油气田高含氯废水,利用活性氯的强氧化性进一步强化废水中难降解有机物SMP的处理;并考察软锰矿粒子电极制备条件对电极性能和电解效果的影响。结果表明:软锰矿与石墨质量比6∶4、PTFE分散液加入量10%、330°C下灼烧2 h为软锰矿粒子电极最优制备条件;与常规活性炭粒子电极相比,软锰矿粒子电极电解活性氯的产生量、COD去除率均显著优于活性炭粒子电极;且软锰矿粒子电极在重复使用多次后,活性组分流失量较小,对SMP的降解效率仍较高,保持了稳定的电催化性能。     

微波—Cu/Fe双金属催化剂—过氧化氢工艺催化降解甲基橙废水的研究

采用超声浸渍法制备了具有较高催化活性的Cu/Fe双金属催化剂。采用微波—Cu/Fe双金属催化剂—过氧化氢工艺处理甲基橙废水,并研究了相关影响因素。结果表明,Cu/Fe双金属催化剂的Cu和Fe具有协同催化效应,可大大提高甲基橙废水的降解率。在Cu/Fe双金属催化剂投加量10g/L、过氧化氢(质量分数为30%)投加体积1.0mL、微波功率500 W、辐照时间5min的最优化条件下,50mL质量浓度为100mg/L的甲基橙废水降解率可达98.94%。     

活性炭三维电极流化床处理洗车废水的研究

以经吸附处理的活性炭为填充粒子,对三维电极流化床反应器处理洗车废水进行了静态条件实验研究。结果表明：三维电极流化床处理洗车废水的效果明显好于三维电极固定床和单纯的活性炭吸附。在槽电压为30 V,通气量为3 L/min, 通电时间为30 min,活性炭用量为50 g时,COD去除率最高。     

三维电催化氧化技术处理草铵膦农药废水

选用石墨板作为三维电催化装置的阳极、不锈钢板作为阴极,以活性炭颗粒作为粒子电极进行反应,研究了三维电催化氧化技术处理草铵膦农药废水的效果;并考察了电流密度、极板间距、电解时间、初始浓度、pH值和粒子电极用量等因素对其处理效果的影响。实验结果表明,在废水初始浓度为300 mg·L~(-1),反应时间为90 min,极板间距为4 cm,pH值为5,电流密度为31.5 m A·cm-2,粒子电极的用量为3.08 g·L~(-1)的条件下,废水的COD去除率为83.48%。三维电催化氧化技术通过减小粒子间距改善电荷传质效果;电流效率的提高也促使废水的处理效果显著提升。     

陶瓷负载Ag、Ce共掺杂TiO_2光催化剂降解甲基橙的研究

以陶瓷为载体,采用溶胶-凝胶法制备了银离子和铈离子共掺杂TiO2的负载型光催化剂——T-AC/陶瓷,研究了pH值、双氧水用量、催化剂用量、紫外灯强度、废水的初始浓度等因素对T-AC/陶瓷光催化剂降解甲基橙染料废水的影响。结果表明,当pH为2、双氧水用量为0.5 mL/100 mL、催化剂用量为3 g/L、紫外灯功率为20 W、废水初始浓度为10mg/L时,甲基橙的降解率可达85.9%,并且甲基橙的光催化降解属于一级动力学方程,T-AC/陶瓷催化剂有较高的活性和稳定性,在废水处理中具有较好的应用前景。     

陶瓷负载Ag、Ce共掺杂TiO2光催化剂降解甲基橙的研究

以陶瓷为载体,采用溶胶-凝胶法制备了银离子和铈离子共掺杂TiO2的负载型光催化剂——T-AC/陶瓷,研究了pH值、双氧水用量、催化剂用量、紫外灯强度、废水的初始浓度等因素对T-AC/陶瓷光催化剂降解甲基橙染料废水的影响。结果表明,当pH为2、双氧水用量为0.5 mL/100 mL、催化剂用量为3 g/L、紫外灯功率为20 W、废水初始浓度为10mg/L时,甲基橙的降解率可达85.9%,并且甲基橙的光催化降解属于一级动力学方程,T-AC/陶瓷催化剂有较高的活性和稳定性,在废水处理中具有较好的应用前景。     

Chloroaromatic pollutants in mussels incubated in two finnish watercourses polluted by industry

Concentrations of different chlorinated compounds were measured in mussels incubated in two polluted watercourses, a river (the River Kymijoki) and a lake (Lake Vanaja) for four weeks in summer 1995. The sum concentrations of polychlorinated phenols (PCP) and biphenyls (PCB) were both about 1 μg/g lipid weight (lw) in Lake Vanaja mussels, while in the River Kymijoki mussels PCPs were non-detectable and PCBs were measured 120 ng/g lIw. The concentrations of toxic polychlorinated dibenzo-p-dioxin (PCDD) and dibenzofuran (PCDF) congeners ranged between <17 and 370 pg/g Iw in Lake Vanaja mussels and between <38 and 11,000 pg/g lw in the River Kymijoki mussels. Polychlorinated diphenyl ethers (PCDE) were detected in the mussels incubated in the River Kymijoki (0.4–1.1 ng/g Iw), but not in those incubated in Lake Vanaja. Polychlorinated phenoxyanisoles (PCPA) were measured 33 ng/g lw and polychlorinated phenoxyphenols (PCPP) 300 ng/g lw in the mussels incubated in the River Kymijoki. PCPAs were also detected in reference samples, which were sediment and pike from the River Kymijoki and Baltic salmon, seal and white-tailed sea eagle.     

Evaluation of trichloroethene recovery processes in heterogeneous aquifer cells flushed with biodegradable surfactants

The ability of two biodegradable surfactants, polyoxyethylene (20) sorbitan monooleate (Tween 80) and sodium dihexyl sulfosuccinate (Aerosol MA), to recover a representative dense non-aqueous-phase liquid (DNAPL), trichloroethene (TCE), from heterogeneous porous media was evaluated through a combination of batch and aquifer cell experiments. An aqueous solution containing 3.3% Aerosol MA, 8% 2-propanol and 6 g/l CaCl(2) yielded a weight solubilization ratio (WSR) of 1.21 g TCE/g surfactant, with a corresponding liquid-liquid interfacial tension (IFT) of 0.19 dyn/cm. Flushing of aquifer cells containing a TCE-DNAPL source zone with approximately two pore volumes of the AMA formulation resulted in substantial (>30%) mobilization of TCE-DNAPL. However, a TCE mass recovery of 81% was achieved when the aqueous-phase flow rate was sufficient to displace the mobile TCE-DNAPL toward the effluent well. Aqueous solutions of Tween 80 exhibited a greater capacity to solubilize TCE (WSR=1.74 g TCE/g surfactant) and exerted markedly less reduction in IFT (10.4 dyn/cm). These data contradict an accepted empirical correlation used to estimate IFT values from solubilization capacity, and indicate a unique capacity of T80 to form concentrated TCE emulsions. Flushing of aquifer cells with less than 2.5 pore volumes of a 4% T80 solution achieved TCE mass recoveries ranging from 66 to 85%, with only slight TCE-DNAPL mobilization (<5%) occurring when the total trapping number exceeded 2 x 10(-5). These findings demonstrate the ability of Tween 80 and Aerosol MA solutions to efficiently recover TCE from a heterogeneous DNAPL source zone, and the utility of the total trapping number as a design parameter for a priori prediction of DNAPL mobilization and bank angle formation when flushing with low-IFT solutions. Given their potential to stimulate microbial reductive dechlorination at low concentrations, these surfactants are well-suited for remedial action plans that couple aggressive mass removal followed by enhanced bioremediation to treat chlorinated solvent source zones.     

Book review

The Pesticide Manual ‐ A World Compendium, 8th Edition, C.R. Worthing, Editor and S.B. Walker, Assistant Editor, British Crop Protection Council, BCPC Publications Sales, Bear Farm, Binfield, Bracknell, Berkshire RG12 5QE, England. 1987, 1100 pp., UK £50; Overseas £56. ISBN 0–948404–01–9.     

The variation of street air levels of PAH and other mutagenic PAC in relation to regulations of traffic emissions and the impact of atmospheric processes

The occurrence of particle associated PAH and other mutagenic PAC was determined in 1996 in the street air of Copenhagen. In addition, particle extracts were tested for mutagenicity. The measurements were compared with previous measurements in 1992/1993. The levels had decreased in this period. The decrease was caused by an implementation of light diesel fuels for buses and the exchange of older petrol-driven passenger cars with catalystequipped new ones. About 65% of the reduction was caused by the application of the light diesel fuels. Under special conditions, chemical processes in the atmosphere produced many more mutagens than the direct emissions. The concentrations of S-PAC and N-PAC were 10 times lower than those of PAH, while the levels of oxy-PAH were in the same order of magnitude as those of PAH. Benzanthrone, an oxy-PAH, is proposed to be formed in the atmosphere in addition to direct emissions. Benzo(a)pyrene, often applied as an air quality criteria indicator, was photochemically degraded in the atmosphere. A strong increase in the mutagenic activities was observed to coincide with a depletion of benzo(a)pyrene.     

Organochlorine compounds in a three-step terrestrial food chain

The concentrations of 15 organochlorine chemicals (PCBs and pesticides) were studied in a Central European oak wood food chain system: Great tit (Parus major), caterpillars (Tortrix viridana, Operophtera brumata, Erannis defoliaria), and oak-leaves (Quercus robur). Juvenile tits receive organochlorines from the mother via egg transfer and, eventually to a greater extent, from the caterpillar food source during nestling period. The concentrations of PCB 153 (2,2′,4,4′,5,5′-hexachlorobiphenyl, the most abundant in this study) was found in leaf material at ca. 1 ng/g, in caterpillars 10 ng/g, and in bird eggs 170 ng/g on an average and on a dry mass basis.     

The chemical stability of formulations of some hydrolyzable insecticides in aqueous mixtures with hydrolysis catalysts

Abstract

The active ingredients in commercial formulations of malathion, oxamyl, carbaryl, diazinon, and chlorpyrifos diluted to “spray tank”; concentrations with buffered distilled or natural water of pH 4–9 were stable for at least 24 hr. Formulations of trichlorfon were not stable at pH 7 or above but disappearance rates were slower than for the pure chemical in homogeneous solution. Cupric ion was observed to be an effective catalyst for the hydrolysis of a variety of pure organophosphorus insecticides but did not catalyze hydrolysis of the active ingredients of the formulations examined. Increasing the dilution of the formulation increased the susceptibility of malathion, oxamyl, and carbaryl to hydrolysis.     

Observations on the influence of water and soil pH on the persistence of insecticides

Abstract

The pH‐disappearance rate profiles were determined at ca. 25°C for 24 insecticides at 4 or 5 pH values over the range 4.5 to 8.0 in sterile phosphate buffers prepared in water‐ethanol (99: 1 v/v). Half‐lives measured at pH 8 were generally smaller than at lower pH values. Changes in half lives between pH 8.0 and 4.5 were largest (>1000x) for the aryl carbamates, carbofuran and carbaryl, the oxime carbamate, oxamyl, and the organophosphorus insecticide, trichlorfon. In contrast, half lives of phorate, terbufos, heptachlor, fensulfothion and aldicarb were affected only slightly by pH changes. Under the experimental conditions described half lives at pH8 varied from 1–2 days for trichlorfon and oxamyl to >1 year for fensulfothion and cyper‐methrin. Insecticide persistence on alumina (acid, neutral and basic), mineral soils amended with aluminum sulfate or calcium hydroxide to different pH values and four natural soils of different pH was examined. No correlation was observed between the measured pH of these solids and the rate of disappearance of selected insecticides applied to them. These observations demonstrate the difficulty of extrapolating the pH dependent disappearance behaviour observed in homogeneous solution to partially solid heterogeneous systems such as soil.     

Teratological effects of pesticides in vertebrates: a review

Abstract

In the last decades, the use and misuse of pesticides in the agriculture have increased, having a severe impact on ecosystems and their fauna. Although the various effects of pesticides on biodiversity have been already documented in several studies, to our knowledge no consistent overview of the impact of pesticides in vertebrates, both terrestrial and aquatic, is available. In this review, we try to present a concise compilation of the teratogenic effects of pesticides on the different classes of vertebrates – mammals, birds, reptiles, amphibians and fish.     

Radionuclides in pinon pine (Pinus edulis) nuts from los alamos national laboratory lands and the dose from consumption

Abstract

One of the dominant tree species growing within and around the eastern portion of Los Alamos National Laboratory (LANL), Los Alamos, NM, lands is the pinon pine (Pinus edulis). Pinon pine is used for firewood, fence posts, and building materials and is a source of nuts for food—the seeds are consumed by a wide variety of animals and are also gathered by people in the area and eaten raw or roasted. This study investigated the (1) concentration of ³H, ¹³⁷Cs, ⁹⁰Sr, ^totU, ²³⁸Pu, ^{239, 240}Pu, and²⁴¹ Am in soils (0‐ to 12‐in. [31 cm] depth underneath the tree), pinon pine shoots (PPS), and pinon pine nuts (PPN) collected from LANL lands and regional background (BG) locations, (2) committed effective dose equivalent (CEDE) from the ingestion of nuts, and (3) soil to PPS to PPN concentration ratios (CRs). Most radionuclides, with the exception of ³H in soils, were not significantly higher (p < 0.10) in soils, PPS, and PPN collected from LANL as compared to BG locations, and concentrations of most radionuclides in PPN from LANL have decreased over time. The maximum net CEDE (the CEDE plus two sigma minus BG) at the most conservative ingestion rate (10 lb [4.5 kg]) was 0.0018 mrem (0.018 μSv); this is far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem (1000 μSv). Soil‐to‐nut CRs for most radionuclides were within the range of default values in the literature for common fruits and vegetables.     

Degradation and sorption of imidacloprid in dissimilar surface and subsurface soils

Degradation and sorption/desorption are important processes affecting the leaching of pesticides through soil. This research characterized the degradation and sorption of imidacloprid (1-[(6-chloro-3-pyridinyl)-methyl]-N-nitro-2-imidazolidinimine) in Drummer (silty clay loam) and Exeter (sandy loam) surface soils and their corresponding subsurface soils using sequential extraction methods over 400 days. By the end of the incubation, approximately 55% of imidacloprid applied at a rate of 1.0 mg kg^?1 degraded in the Exeter sandy loam surface and subsurface soils, compared to 40% of applied imidacloprid within 300 days in Drummer surface and subsurface soils. At the 0.1 mg kg^?1 application rate, dissipation was slower for all four soils. Water-extractable imidacloprid in Exeter surface soil decreased from 98% of applied at day 1 to > 70% of the imidacloprid remaining after 400 d, as compared to 55% in the Drummer surface soil at day 1 and 12% at day 400. These data suggest that imidacloprid was bioavailable to degrading soil microorganisms and sorption/desorption was not the limiting factor for biodegradation. In subsurface soils > 40% of ¹⁴C-benzoic acid was mineralized over 21 days, demonstrating an active microbial community. In contrast, cumulative ¹⁴CO₂ was less than 1.5% of applied ¹⁴C-imidacloprid in all soils over 400 d. Qualitative differences in the microbial communities appear to limit the degradation of imidacloprid in the subsurface soils.