Preparation of MgCr<Subscript>2</Subscript>O<Subscript>4</Subscript> from waste tannery solution and effect of sulfate,chloride, and calcium on leachability of chromium

This paper presents a study regarding the preparation of MgCr₂O₄ from waste tannery solution, and chromium leaching behavior is also investigated with varying amounts of sulfate, chloride and calcium. The phase transformation, crystallinity index and crystallite diameter were characterized using XRD, FT-IR and thermal analysis. A well-crystallized MgCr₂O₄ was successfully prepared at 1400 °C. The sintering temperature had a major impact on the formation of MgCr₂O₄ compared with sintering time. The MgCr₂O₄ phase was observed initially at 400 °C and its crystallite diameter increased with increasing temperature. The concentration of total chromium leached and Cr(VI) decreased gradually with increasing temperature. The considerable amount of Cr(VI) was found in the leachate at 300–500 °C caused by Cr(VI) intermediary products. Sulfate and chlorine could impact the transformation efficiency of chromium adversely, and chlorine has a more significant effect than sulfate. The presence of calcium disturbed the formation of MgCr₂O₄ and new chromium species (CaCrO₄) appeared, which resulted in a sharp increase in the concentration of leached Cr(VI). Incorporating Cr(III) into the MgCr₂O₄ spinel for reusable products reduced its mobility significantly. This was demonstrated to be a promising strategy for the disposal of chromium containing waste resource.     

The use of waste basic oxygen furnace slag and hydrogen peroxide to degrade 4-chlorophenol

A new treatment method is developed to degrade 4-chlorophenol (4-cp) and its oxidation intermediates. The experimental results of this research demonstrate that 4-cp and its oxidation intermediates can be decomposed completely by basic oxygen furnace slag (BOF slag) with hydrogen peroxide (H₂O₂) in an acid solution. The factors that effect the treatment efficiency were studied including initial concentration of 4-cp, pH of the solution, concentration of H₂O₂ and amount of BOF slag. The BOF slags are final waste materials in the steel making process. The major components of BOF slag are CaO, SiO₂, Fe₂O₃, FeO, MgO and MnO. As the BOF slag in an acid solution, FeO and Fe₂O₃ can be dissociated to produce ferrous ion and ferric ion. Ferrous ion reacts with hydrogen peroxide to form “Fenton's reagent” which can produce hydroxyl radicals (OH^.). Hydroxyl radical possession of high oxidation ability can oxidize organic chemicals effectively. Results show that 100 mg/l of 4-cp is decomposed completely within 30 min by 438.7 g/l BOF slag with 8.2 mM hydrogen peroxide in pH=2.8±0.2 solution. The COD value of the solution is reduced from 290 to 90 mg/l. The factors studied which affect the 4-cp decomposition efficiency were the hydrogen peroxide concentration, BOF slag concentration, pH of the solution and initial concentration of 4-cp. Because large amounts of Fe₂O₃ and FeO are present in the BOF slag, the BOF slag not only has a high treatment efficiency, but also can be used repeatedly.     

Effect of additives on dechlorination of PVC by mechanochemical treatment

Polyvinyl chloride (–CH₂–CHCl–) _n (PVC) was ground with a powdered inorganic material (CaO, CaCO₃, SiO₂, Al₂O₃, or slag) in a planetary ball mill under atmospheric conditions to investigate the effect of additions on its dechlorination. The grinding causes a dehydrochlorinating reaction, forming a mixture of partially dechlorinated PVC and inorganic chloride, depending on the grinding time. The dechlorination increases as the grinding progresses, and is improved with increasing amounts of additives. The most effective additive is a mixture of CaO, SiO₂, and Al₂O₃, which has the same constituent components as blast furnace slag. CaO, a mixture of CaO, SiO₂, and blast furnace slag, are also effective, but CaCO₃ is the least effective additive tired. Received: August 3, 2000 / Accepted: September 21, 2000     

Dynamic studies on lead volatilization from CaO–SiO2–Al2O3 molten slag under N2–CO–CO2, N2–HCl and N2–H2S gas atmospheres

Dynamic studies on the volatilization of lead from CaO–SiO₂–Al₂O₃ molten slags were conducted in a lab-scale melting furnace from 1623 to 1773 K under different mixed gas atmospheres of CO 0.05–0.3 atm to CO₂ 0–0.3 atm to N₂ (balance), HCl 1.7 × 10^?3–6.7 × 10^?3 atm to N₂ (balance), and H₂S 3.0 × 10^?4 to 1.7 × 10^?3 atm to N₂ (balance). The slag samples consisted of the mixed powders of 20–50 wt% CaO, 30–60 wt% SiO₂, and 10–40 wt% Al₂O₃, containing 2000 ppm PbO.Results showed that the rates of volatilization of lead from the CaO–SiO₂–Al₂O₃ molten slags under the N₂–CO–CO₂, N₂–HCl, and N₂–H₂S gas atmospheres were higher than those under the simulated air (N₂–O₂), which increased with CO, HCl, and H₂S partial pressures. At \(p_{{HCl}}\)  =  \(p_{H_{2}S}\)  = 1.7 × 10^?3 atm, the apparent rate constants for the volatilization of lead under the N₂–H₂S and N₂–HCl gas atmospheres were nearly equal, which increased with a rise in temperature. Results also showed that the rate of volatilization of lead from the molten slag decreased drastically with the increasing viscosity of the molten slag, in the viscosity range lower than 3 Pa s. Consequently, the volatilization of lead from the CaO–SiO₂–Al₂O₃ molten slag was significantly influenced by CO, HCl, and H₂S partial pressures and by the viscosity of the molten slag.     

Resurrection of the iron and phosphorus resource in steel-making slag

 This research focused on the treatment of steel-making slags to recycle and recover iron and phosphorus. The carbothermal reduction behavior of both synthesized and factory steel-making slag in microwave irradiation was investigated. The slags were mixed with graphite powder and heated to a temperature higher than 1873 K to precipitate a lump of Fe–C alloy with a diameter of 2–8 mm. The larger the carbon equivalent (C_eq, defined in the text), the higher the fractional reduction of iron and phosphorus. An increase in the SiO₂ content of slag led to a considerable improvement in the reduction for both iron and phosphorus because of the improvement in the fluidity of the slags and an increase in the activity coefficient of P₂O₅ in the slags. The extraction behavior of phosphorus from Fe–P–C_satd alloy was also investigated at 1473 K by carbonate flux treatment. For all the experiments with a processing time longer than 10 min, the phosphorus in the fluxes could be concentrated to more than 9% (w/w) showing that it could be used as a phosphorus resource. Compared with K₂CO₃ flux treatment, that using Na₂CO₃ was more effective for the extraction of phosphorus, and this was attributed to the lower evaporation of Na₂CO₃. Finally, a recycling scheme for steel-making slag is proposed. Received: March 16, 2001 / Accepted: November 12, 2001     

Stabilization and utilization of hospital waste as road and asphalt aggregate

This article reports the operational results of the effective utilization of hospital waste molten slag produced using a high-temperature melting system, and being operated at a hospital in Selangor, Malaysia. The hospital waste is incinerated and subsequently melted at 1200°C. Scanning election microscope (SEM)/EDX results showed that the slag produced after melting contained amounts of SiO₂, CaO, and Al₂O₃ in excess of 53%, 9%, and 16%, respectively. The results from a leaching analysis on the slag produced proved that the melting process had successfully stabilized the heavy metals. The use of this slag as an alternative material to replace conventional aggregates for road construction was studied. The results from aggregate and asphalt mix tests showed that the slag produced fulfills all the requirements of an alternative aggregate. The average asphalt content, or the optimum asphalt content to be mixed with hospital waste molten slag, was found to be about 5.53%.     

Synthesis of hydrogarnet from molten slag and its hydrogen chloride fixation performance at high temperature

Hydrogarnet was synthesized hydrothermally below 200°C using molten slag obtained from municipal solid waste. For comparison, it was also synthesized using pure-phase CaO–Al₂O₃–SiO₂–H₂O, as reported previously. The structural and textural properties of this material were investigated using various analytical and spectroscopic techniques such as X-ray diffraction, X-ray fluorescence spectrometry, atomic absorption spectrometry (AAS), thermogravimetry/differential thermal analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy. The Cl⁻ fixation ability of hydrogarnet was investigated in the temperature range 500–800°C in a fixed-bed flow reactor using a HCl concentration (1000 p.p.m.v.) similar to that of incinerator exhaust gas. Under these experimental conditions, the hydrogarnet was capable of reducing the HCl gas level to less than 1 p.p.m.v. Analysis of the spent catalyst revealed that the hydrogarnet was being transformed into wadalite and CaCl₂ at high temperatures. The elution test for chromium ions in hydrogarnet obtained from slag was also used, and it was found that chromium ions were not eluted from hydrogarnet. Received: January 27, 2001 / Accepted: October 11, 2001     

Synthesis of chromium-containing pigments from chromium recovered from leather waste

Cobalt-chromite green and chrome-tin pink pigments have been prepared from chromium extracted from leather shavings produced as a waste product of the leather-tanning industry. The alkaline agent (NaOH, CaO, MgO, NH4OH) used in the extraction process influences the nature of the final product. The effect of the NH4OH:CaO ratio on the final product in the case of cobalt-chromite green was examined. The pigments obtained were characterized by FT-IR and X-ray diffraction (XRD). Colour measurements were compared with those recorded from materials prepared from pure Cr2O3. The leaching of Cr(VI) from the materials was examined by UV spectroscopy.     

Volatilization behavior of lead from molten slag under conditions simulating municipal solid waste melting

To reutilize molten slag derived from an ash melting process, the lead volatilization mechanism under reducing conditions was investigated. Reducing conditions were established by introducing a CO-CO₂-N₂ gas mixture to the reactor or by adding graphite to the molten slag prior to the experiments. As samples, two types of simulated molten slag composed of CaO-SiO₂-Al₂O₃ mixed with PbO were used and the lead volatilization behavior was studied at 1773 K. It was found that the lead volatilization rate increased on increasing the amount of reducing agent for both graphite and the CO-CO₂ gas mixture. For the CO-CO₂ reducing gas mixture, this increase was mainly attributed to PbO conversion to Pb. For the addition of graphite, the increase in lead volatilization ratio was considered to partially result from PbO conversion to Pb and partially from a reaction of graphite with SiO₂ yielding volatile SiO. The volatile SiO gas was then emitted from the furnace, which brought about a reduction in the SiO₂ content of the slag. As a result, the slag viscosity decreased, which led to an enhancement of the lead volatilization ratio.     

Utilization of alum sludge waste for production of eco-friendly blended cement

This work was focused on evaluating the suitability of replacing Portland cement (PC) by 5, 10 and 15 mass % of activated alum sludge waste (AAS) as a pozzolanic material. Exploitation of low-cost nanocomposite for bolstering the physical, mechanical, and stability against firing of PC–AAS-hardened composites was inspected. CuFe₂O₄ spinel nanoparticle with average particle size (~ 50 nm) was prepared. Inclusion of CuFe₂O₄ spinel in different PC–AAS-hardened composites bolsters their physicomechanical features at almost normal curing ages as well as their stability against firing. The positive impact of synthesized CuFe₂O₄ spinel was affirmed via TGA/DTG and XRD techniques, which indicated the presence of diverse hydration yields such as CSHs, CASHs, CFSH, and CuSH that enhance the overall physicomechanical characteristics and thermal stability of various PC–AAS-hardened composites. The composite containing (90 PC–10 AAS waste–2 CuFe₂O₄) offers many benefits from the economic and environmental view.

Graphical abstract

     

Characteristics of steel slag under different cooling conditions

Four types of steel slags, a ladle slag, a BOF (basic oxygen furnace) slag and two different EAF (electric arc furnace) slags, were characterized and modified by semi-rapid cooling in crucibles and rapid cooling by water granulation. The aim of this work was to investigate the effect of different cooling conditions on the properties of glassy slags with respect to their leaching and volume stability. Optical microscopy, X-ray diffraction, scanning electron microscope and a standard test leaching (prEN 12457-2/3) have been used for the investigation. The results show that the disintegrated ladle slag was made volume stable by water granulation, which consisted of 98% glass. However EAF slag 1, EAF slag 2 and the BOF slag formed 17%, 1% and 1% glass, respectively. The leaching test showed that the glass-containing matrix did not prevent leaching of minor elements from the modified slags. The solubility of chromium, molybdenum and vanadium varied in the different modifications, probably due to their presence in different minerals and their different distributions.     

Mineralogy and pore water chemistry of a boiler ash from a MSW fluidized-bed incinerator

This paper presents an investigation of the mineralogy and pore water chemistry of a boiler ash sampled from a municipal solid waste fluidized-bed incinerator, subject to 18 months of dynamic leaching in a large percolation column experiment. A particular focus is on the redox behaviour of Cr(VI) in relation to metal aluminium Al⁰, as chromium may represent an environmental or health hazard. The leaching behaviour and interaction between Cr(VI) and Al⁰ are interpreted on the basis of mineralogical evolutions observed over the 18-month period and of saturation indices calculated with the geochemical code PhreeqC and reviewed thermodynamic data. Results of mineralogical analyses show in particular the alteration of mineral phases during leaching (e.g. quartz and metal aluminium grains), while geochemical calculations suggest equilibria of percolating fluids with respect to specific mineral phases (e.g. monohydrocalcite and aluminium hydroxide). The combination of leaching data on a large scale and mineralogical analyses document the coupled leaching behaviour of aluminium and chromium, with chromium appearing in the pore fluids in its hexavalent and mobile state once metal aluminium is no longer available for chromium reduction.     

Copper stabilization in beneficial use of waterworks sludge and copper-laden electroplating sludge for ceramic materials

A promising strategy for effectively incorporating metal-containing waste materials into a variety of ceramic products was devised in this study. Elemental analysis confirmed that copper was the predominant metal component in the collected electroplating sludge, and aluminum was the predominant constituent of waterworks sludge collected in Hong Kong. The use of waterworks sludge as an aluminum-rich precursor material to facilitate copper stabilization under thermal conditions provides a promising waste-to-resource strategy. When sintering the mixture of copper sludge and the 900 °C calcined waterworks sludge, the CuAl₂O₄ spinel phase was first detected at 650 °C and became the predominant product phase at temperatures higher than 850 °C. Quantification of the XRD pattern using the Rietveld refinement method revealed that the weight of the CuAl₂O₄ spinel phase reached over 50% at 850 °C. The strong signals of the CuAl₂O₄ phase continued until the temperature reached 1150 °C, and further sintering initiated the generation of the other copper-hosting phases (CuAlO₂, Cu₂O, and CuO). The copper stabilization effect was evaluated by the copper leachability of the CuAl₂O₄ and CuO via the prolonged leaching experiments at a pH value of 4.9. The leaching results showed that the CuAl₂O₄ phase was superior to the CuAlO₂ and CuO phases for immobilizing hazardous copper over longer leaching periods. The findings clearly indicate that spinel formation is the most crucial metal stabilization mechanism when sintering multiphase copper sludge with aluminum-rich waterworks sludge, and suggest a promising and reliable technique for reusing both types of sludge waste for ceramic materials.     

Reductive decomposition of waste gypsum with SiO<Subscript>2</Subscript>, Al<Subscript>2</Subscript>O<Subscript>3</Subscript>, and Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> additives

From the point of view of a sustainable and environment-friendly society based on the recycling of material resources, it is preferable to utilize waste gypsum as a substitute for lime, which is currently produced by the calcination of limestone. In the present work, the reductive decomposition of CaSO₄ was investigated under an atmosphere of CO: 2 vol%, CO₂: 30 vol%, with N₂ as a carrier gas without and with the addition of SiO₂, Al₂O₃, or Fe₂O₃. It was found that the decomposition temperature of CaSO₄ was significantly reduced from 1673 K to 1223 K when only 5 wt% Fe₂O₃ was added to CaSO₄. In the case of the addition of SiO₂ or Al₂O₃ to CaSO₄, the decomposition temperature was reduced from 1673 K to 1623 K. This was due to the formation of composite oxides (calcium ferrite, calcium silicate, or calcium aluminate) during the reaction of CaSO₄ with the additives at a lower temperature. In addition, the formation of unfavorable product CaS was inhibited in the presence of 5 wt% Fe₂O₃, and this inhibition effect further increased as the addition of Fe₂O₃ was increased. In contrast, no significant effect on the inhibition of CaS formation was observed on the addition of SiO₂ or Al₂O₃.     

Effect of crystal size on zinc stabilization in aluminum-rich ceramic matrix

With aluminum as the predominant element, incineration residues from municipal solid waste and sewage sludge may be reused as precursors for zinc stabilization. As solid-state reactions are influenced by the crystal sizes of the reactants, the aluminum-containing components with different crystal sizes in the incineration residues may affect zinc transformation and immobilization. In this study, Al₂O₃ was prepared with a variety of crystal sizes to simulate the aluminum-rich incineration residue matrix, and ZnO was mixed with Al₂O₃ to study the zinc incorporation mechanisms. The crystal sizes of Al₂O₃ were determined using Rietveld refinement. Quantification results showed that ~?30% of zinc was incorporated into the ZnAl₂O₄ spinel when Al₂O₃ with the largest crystal size was used. However, the zinc transformation was enhanced twofold when the Al₂O₃ precursor had the smallest crystal size. This study confirmed the potential enhancement of zinc immobilization by nanoscale crystals in simulated aluminum-rich incineration residues. By improving zinc stabilization efficiencies using poorly crystallized aluminum-containing compounds instead of increasing the energy consumption by increasing the sintering temperatures, we can achieve an economic and environmental win–win scenario for the beneficial utilization of incineration residues of municipal solid waste and sewage sludge.     

Metallic-phase lead in slag of municipal solid waste incineration ash and leaching characteristics

Metallic phases in slags and their influence on the leaching characteristics were investigated. The proportions of metallic phase in four slags were 0.028%, 0.24%, 1.87%, and 3.05% by weight. The lead content was 10–248 mg/kg in bulk slag after metal removal, while in the metallic phase it was 579–7390 mg/kg. Lead concentrations in the metallic phase were more than ten times higher than in slags after metal removal. Lead was distributed in the metallic phase at 2.0%, 8.3%, 10.3%, and 47.4%. The concentrations of all metallic elements in metallic phases were much higher than in bulk slag. Iron, copper, and nickel had accumulated in magnetic metals, while aluminum and zinc were found in nonmagnetic metals. As regards chromium, manganese, lead, and tin, the proportion of metallic phases depended on the slag samples. By removing metallic phases, both water and pH 4 leachable lead decreased. The basic principles of melting residues containing lead are the separation of lead as a metal in reductive melting, and the containment of lead ions into uniform glassy particles in oxidization melting. Melting slag can be seen to contribute to environmental preservation by facilitating the recycling of materials through the separation of metals from melting slag. Received: February 21, 2000 / Accepted: July 27, 2000     

干式还原法处理铬渣的机理及应用

采用干式还原法处理铬渣。在多级还原焙烧炉中于高温条件下,将过量的煤粉和铬渣混合后与O₂反应,经冷却、擦磨、磁分离后可得到铁精砂和处理后铬渣。介绍了干式还原法处理铬渣的机理和工艺参数。以3种铬渣试样进行应用试验,经多级还原焙烧—磁分离后,铬渣中的Cr（Ⅵ）质量浓度为0.05~0.18 mg/L,低于HJ/T301—2007标准中的要求（0.50 mg/L）,可作为建材原料加以利用。磁分离得到的铁精砂产品中铁的质量分数大于50%,铁回收率大于70%。目前设计的多级还原焙烧炉单炉处理铬渣能力为150 kt/a,标煤消耗为35 kg/t,处理成本约为60元/t。     

Kinetics of steel slag leaching: Batch tests and modeling

Reusing steel slag as an aggregate for road construction requires to characterize the leaching kinetics and metal releases. In this study, basic oxygen furnace (BOF) steel slag were subjected to batch leaching tests at liquid to solid ratios (L/S) of 10 and 100 over 30 days; the leachate chemistry being regularly sampled in time. A geochemical model of the steel slag is developed and validated from experimental data, particularly the evolution with leaching of mineralogical composition of the slag and trace element speciation. Kinetics is necessary for modeling the primary phase leaching, whereas a simple thermodynamic equilibrium approach can be used for secondary phase precipitation. The proposed model simulates the kinetically-controlled dissolution (hydrolysis) of primary phases, the precipitation of secondary phases (C-S-H, hydroxide and spinel), the pH and redox conditions, and the progressive release of major elements as well as the metals Cr and V. Modeling indicates that the dilution effect of the L/S ratio is often coupled to solubility-controlled processes, which are sensitive to both the pH and the redox potential. A sensitivity analysis of kinetic uncertainties on the modeling of element releases is performed.     

The behaviors of H2, CH4, C2H4 and C3H6 from the decomposition of polypropylene by NiO/Si–Al catalyst

The purpose of this study was to investigate the possibility of light gases produced from polypropylene, specifically hydrogen. In particular, we examined the effect of operating conditions on gaseous product and compositions in the catalytic cracking of polypropylene. We also characterized the gaseous product generated from polypropylene cracking. The feedstock (2.0 g) mixed with NiO/SiO₂–Al₂O₃ (Si–Al) was used, under non-isothermal conditions at low temperature range between 380 and 500 °C. Argon gas was used to carry the pyrolyzed gas, and the gas collected in a tedlar bag was analyzed for its behavior. We observed the behavior of major gases (H₂, CH₄, C₂H₄ and C₃H₆, etc.) according to reaction time and temperature. Finally, the effect of reaction conditions on evolved gases from catalytic cracking of polypropylene was analyzed.     

Techniques to separate metal from waste printed circuit boards from discarded personal computers

Waste printed circuit boards contain valuable metals such as Au, Pd, Ag, and Cu that can be reutilized and harmful elements such as Pb, Br, and Cr that must be removed from the viewpoint of environmental conservation. In this research, we examined a method that separates the materials from printed circuit boards contained in discarded personal computers. After cutting the printed circuit boards to a size of 20 × 20 mm, they were heated at 873 K under an Ar atmosphere to remove organic resins containing elements such as C, H, and N. After heat treatment, the printed circuit boards were crushed using a planetary ball mill and the pulverized powders were filtered. The fraction with a granularity of greater than 250 μm was separated into magnetic and nonmagnetic materials by a magnetic field. Because the fraction with a granularity of less than 250 μm contained 39 mass% of C, it was heated at 1273 K in an atmosphere of 95% Ar and 5% O₂ to allow carbon combustion to take place, followed by metal reduction processing at the same temperature in an atmosphere of 97% Ar and 3% H₂. The basicity of the resulting powder was adjusted and the powder was heated at 1773 K under an Ar atmosphere. The proposed method separated the slag and metal, and 80% of the valuable metals contained in printed circuit boards could be collected.