Detrimental effects of olive mill wastewater on the composting process of agricultural wastes

In order to study the suitability of composting olive mill wastewater (OMW-L) by repeated applications, OMW-L was added to one mixture of lawn trimmings and olive husks as bulking agents. The composting process of this mixture was compared with another pile having 35% of olive mill wastewater sludge (OMW-S) obtained from evaporation ponds and a third, as a control, without olive mill wastewater. The repeated applications of OMW-L resulted in a sharp decrease in respiration measurements after the first 20 days of composting and showed a re-increase after 40 days following the substituting of OMW-L by water. The OMW-L addition increased the rate of water-soluble phenols in the compost and caused the appearance of a phenol fraction of high molecular-mass (510 kDa) at the end of composting. OMW-L addition also caused a clear decrease in both thermophilic bacteria and thermophilic eumycete counts. A longer persistence of phytotoxicity was observed in comparison with the other piles. However, the OMW-S produced a compost with a high degree of maturity.     

In-vessel composting of household wastes

The process of composting has been studied using five different types of reactors, each simulating a different condition for the formation of compost; one of which was designed as a dynamic complete-mix type household compost reactor. A lab-scale study was conducted first using the compost accelerators culture (Trichoderma viridae, Trichoderma harzianum, Trichorus spirallis, Aspergillus sp., Paecilomyces fusisporus, Chaetomium globosum) grown on jowar (Sorghum vulgare) grains as the inoculum mixed with cow-dung slurry, and then by using the mulch/compost formed in the respective reactors as the inoculum. The reactors were loaded with raw as well as cooked vegetable waste for a period of 4 weeks and then the mulch formed was allowed to maturate. The mulch was analysed at various stages for the compost and other environmental parameters. The compost from the designed aerobic reactor provides good humus to build up a poor physical soil and some basic plant nutrients. This proves to be an efficient, eco-friendly, cost-effective, and nuisance-free solution for the management of household solid wastes.     

LCA comparison of windrow composting of yard wastes with use as alternative daily cover (ADC)

This study compared the environmental impacts of composting yard wastes in windrows with using them in place of soil as alternative daily cover (ADC) in landfills. The Life Cycle Assessment was made using the SimaPro LCA software and showed that the ADC scenario is more beneficial for the environment than windrow composting. ADC use is also a less costly means of disposal of yard wastes. This finding applies only in cases where there are sanitary landfills in the area that are equipped with gas collection systems and can use yard wastes as alternative daily cover. Otherwise, the environmentally preferable method for disposal of source-separated yard wastes is composting rather than landfilling.     

Microbial inoculants for small scale composting of putrescible kitchen wastes

This research looked at the need for ligno-cellulolytic inoculants (EM bacteria and Trichoderma sp.) in small to medium scale composting of household wastes. A mixture of household organic waste comprised of kitchen waste, paper, grass clippings and composted material was subjected to various durations of thermo composting followed by vermicomposting with and without microbial inoculants for a total of 28 days. The results revealed that ligno-celluloytic inoculants are not essential to speed up the process of composting for onsite small scale household organic waste treatment as no significant difference was observed between the control and those inoculated with Trichoderma and EM in terms of C:N ratio of the final product. However, it was observed that EM inoculation enhanced reproductive rate of earthworms, and so probably created the best environment for vermicomposting, in all treatment groups.     

Indicator organisms for assessing sanitization during composting of plant wastes

The potential for using plant pathogens and seeds as indicator organisms for assessing sanitization of plant wastes during composting was tested in bench-scale flask and large-scale systems. Plasmodiophora brassicae was unsuitable due to high temperature tolerance in dry to moist composts, and detection of viable inoculum post-composting using bioassay plants not corresponding with that using TaqMan® PCR, possibly due to preservation of nucleic acids at elevated temperatures. Several other plant pathogens (Sclerotinia sclerotiorum, Microdochium nivale, Phytophthora cinnamomi and Phytophthora nicotianae) were unsuitable due their low temperature tolerance. Fusarium oxysporum f.sp. cepae and f.sp. radicis-lycopersici chlamydospores and tomato seeds were suitable indicators due to their moderate temperature tolerance and ease of viability testing post-composting. Abutilon seeds were more tolerant than tomato seeds of compost temperatures ?52 °C but more prone to degradation at lower temperatures and therefore less suitable as indicators. Relationships between compost temperature during exposures of 2-10 days and subsequent viability of the above chlamydospores or seeds enabled the sanitizing effect of composting processes to be predicted within 2-6 days. Plant waste type (woody or vegetable) had a small but significant effect on the relationship for tomato seeds but not for F. oxysporum chlamydospores.     

Dynamic of functional microbial groups during mesophilic composting of agro-industrial wastes and free-living (N2)-fixing bacteria application

Although several reports are available concerning the composition and dynamics of the microflora during the composting of municipal solid wastes, little is known about the microbial diversity during the composting of agro-industrial refuse. For this reason, the first parts of this study included the quantification of microbial generic groups and of the main functional groups of C and N cycle during composting of agro-industrial refuse. After a generalized decrease observed during the initial phases, a new bacterial growth was observed in the final phase of the process. Ammonifiers and (N₂)-fixing aerobic groups predominated outside of the piles whereas, nitrate-reducing group increased inside the piles during the first 23 days of composting. Ammonia-oxidizing bacteria (AOB) and nitrite-oxidizing bacteria (NOB), showed an opposite trend of growth since ammonia oxidation decreased with the increase of the nitrite oxidation activity. Pectinolytics, amylolytics and aerobic cellulolytic were present in greater quantities and showed an upward trend in both the internal and external part of the heaps.Several free-living (N₂)-fixing bacteria were molecularly identify as belonging especially to uncommon genera of nitrogen-fixing bacteria as Stenotrophomonas, Xanthomonas, Pseudomonas, Klebsiella, Alcaligenes, Achromobacter and Caulobacter. They were investigated for their ability to fix atmospheric nitrogen to employ as improvers of quality of compost. Some strains of Azotobacter chrococcum and Azotobacter salinestris were also tested. When different diazotrophic bacterial species were added in compost, the increase of total N ranged from 16% to 27% depending on the selected microbial strain being used. Such microorganisms may be used alone or in mixtures to provide an allocation of plant growth promoting rhizobacteria in soil.     

Effects of basaltic mineral fines on composting

A by-product of the construction aggregate industry is fines or dust that contain trace elements such as zinc and copper and significant amounts of iron, aluminum, silica and potassium. Beneficial uses for these materials have been proposed such as replenishing depleted soils and amendment in mixtures of organic byproducts prior to composting. To evaluate the beneficial uses in composting, outdoor bin studies were conducted using a beef cattle manure, straw and wood chip mixture amended with and without basaltic mineral fines. Temperature differences in composting mixtures of equal volumes, equal moisture and relatively equal material content are considered an indication of differing biological activities [Haug, Compost Engineering Principles and Practice. Ann Arbor Science, Ann Arbor, MI. (1980)]. Temperatures were lower in the mineral fine-treated manure mixture initially. After turning the piles at six weeks, temperatures tended to be higher in the mineral fine amended mixture. Overall, temperatures were not significantly different suggesting that mineral fines amendment does not significantly increase temperature and activity in composting mixtures.     

Development of composting process of oil palm industrial wastes by multi-enzymatic fungal system

There is an increased interest in composting as an effective means of handling large amounts of organic wastes generated by oil palm industries in Malaysia. However, very few studies have been conducted to develop an effective composting process using the multi-enzymatic system. This study demonstrates an effective composting process of EFB (empty fruit bunch) with POME (palm oil mill effluent), using the optimized process parameters and compatible multi-enzymatic fungal system. A higher decrease (3 %) of organic matter was achieved in the fungal treated system, almost double that of the control (without inoculum). The lowest C/N ratio and soluble protein content recorded were about 17 and 128.82 g/kg, respectively. The maximum germination index obtained was 116 % at day 50 of treatment, which is considered high compared to the control (uninoculated). Furthermore, the maximum activity of ligninase enzyme was found to be 25.95 U/g and the highest cellulase activity was recorded at 0.975 U/g.     

Biosorption of copper from aqueous solutions utilizing agricultural wastes

The purpose of this study was to determine the copper (Cu) biosorption capacities of several agricultural wastes from aqueous solutions. Samples of agricultural wastes were tested unaltered and after hydrochloric acid (HCl) treatment. Additional parameters tested include sample dose, contact time, particle size, mixing temperature, and the concentrations and pH of the Cu solutions. Desorption studies were performed to determine if the removed Cu could be recovered. In addition, tests were conducted to determine if the agricultural waste samples (AWS) could be reused for additional Cu biosorption cycles. The results of this study demonstrate a wide range of Cu biosorption proficiencies ranging from 0% to 100% removal. The parameters that resulted in higher Cu removal include higher pH and lower Cu solution concentration. Desorption results showed a 58% to 86% Cu recovery rate. Three of the five reused AWS were effective at removing Cu during subsequent trials. Therefore, these AWS types can be reused for additional Cu biosorption cycles. Hence, it is possible that using those AWS for metal treatment could reduce hazardous waste disposal inefficiencies and costs by avoiding disposing of spent AWS following each Cu biosorption cycle.     

Open windrow composting of polymers: an investigation into the operational issues of composting polyethylene (PE)

This paper investigates the operational issues surrounding the open windrow composting of degradable polyethylene sacks. Areas for consideration were the impact of degradable polyethylene sacks on the composting process, the quality of the finished compost product, and how the use of sacks influenced the on-site processing. These factors were investigated through determining the amount of polymer residue and chemical contaminants in the finished compost product and the daily monitoring of windrow temperature profiles. Site and practical handling considerations of accepting an organic waste contained within PE sacks are also discussed. Statistical analysis of the windrow temperature profiles has led to the development of a model that can help to predict the expected trends in the temperature profiles of open compost windrows where the organic waste is kerbside collected using a degradable PE sack.     

Comparison of five organic wastes regarding their behaviour during composting: Part 2, nitrogen dynamic

This paper aimed to compare household waste, separated pig solids, food waste, pig slaughterhouse sludge and green algae regarding processes ruling nitrogen dynamic during composting. For each waste, three composting simulations were performed in parallel in three similar reactors (300 L), each one under a constant aeration rate. The aeration flows applied were comprised between 100 and 1100 L/h. The initial waste and the compost were characterized through the measurements of their contents in dry matter, total carbon, Kjeldahl and total ammoniacal nitrogen, nitrite and nitrate. Kjeldahl and total ammoniacal nitrogen and nitrite and nitrate were measured in leachates and in condensates too. Ammonia and nitrous oxide emissions were monitored in continue. The cumulated emissions in ammonia and in nitrous oxide were given for each waste and at each aeration rate. The paper focused on process of ammonification and on transformations and transfer of total ammoniacal nitrogen. The parameters of nitrous oxide emissions were not investigated. The removal rate of total Kjeldahl nitrogen was shown being closely tied to the ammonification rate. Ammonification was modelled thanks to the calculation of the ratio of biodegradable carbon to organic nitrogen content of the biodegradable fraction. The wastes were shown to differ significantly regarding their ammonification ability. Nitrogen balances were calculated by subtracting nitrogen losses from nitrogen removed from material. Defaults in nitrogen balances were assumed to correspond to conversion of nitrate even nitrite into molecular nitrogen and then to the previous conversion by nitrification of total ammoniacal nitrogen. The pool of total ammoniacal nitrogen, i.e. total ammoniacal nitrogen initially contained in waste plus total ammoniacal nitrogen released by ammonification, was calculated for each experiment. Then, this pool was used as the referring amount in the calculation of the rates of accumulation, stripping and nitrification of total ammoniacal nitrogen. Separated pig solids were characterised by a high ability to accumulate total ammoniacal nitrogen. Whatever the waste, the striping rate depended mostly on the aeration rate and on the pool concentration in biofilm. The nitrification rate was observed as all the higher as the concentration in total ammoniacal nitrogen in the initial waste was low. Thus, household waste and green algae exhibited the highest nitrification rates. This result could mean that in case of low concentrations in total ammoniacal nitrogen, a nitrifying biomass was already developed and that this biomass consumed it. In contrast, in case of high concentrations, this could traduce some difficulties for nitrifying microorganisms to develop.     

Effects of air flow directions on composting process temperature profile

In this study, chicken manure mixed with carnation wastes was composted by using three different air flow directions: R1-sucking (downward), R2-blowing (upward) and R3-mixed. The aim was to find out the most appropriate air flow direction type for composting to provide more homogenous temperature distribution in the reactors. The efficiency of each aeration method was evaluated by monitoring the evolution of parameters such as temperature, moisture content, CO(2) and O(2) ratio in the material and dry material losses. Aeration of the reactors was managed by radial fans. The results showed that R3 resulted in a more homogenous temperature distribution and high dry material loss throughout the composting process. The most heterogeneous temperature distribution and the lowest dry material loss were obtained in R2.     

Quality assessment of composts prepared with olive mill wastewater and agricultural wastes

The co-composting of solid residue from olive oil production process, exhausted olive cake (EOC), with poultry manure (PM) watered with olive mill wastewater (OMW) was considered as an efficient method for the treatment of olive oil extraction effluent having high organic content including phenolic polluting compounds. The process was carried out by using three aerated windrows of variable compositions. OMW was used continuously during the bio-oxidative period, which lasted three months, to replace water for windrow moistening. The main process parameters (temperature, pH, humidity and C/N) were monitored over four months to ascertain the maturity of the compost. The composting process lasted four months during which 26 moistenings of the mixtures were performed with OMW or water to keep moisture within the ideal range of 45-60% (w/w). At the maturity stage, the C/N ratios were less than 16, pH of the resulting products were slightly alkaline (pH=8) and electrical conductivity was relatively high in the OMW mixtures (5.46-5.48 Sm(-1)) when compared with water application. Nitrates increased (0.16-0.42%) and phenol contents were reduced by more than 49%. Mature composts were then used as an amendment for potato production in a field where no inhibitory effect was observed. Potato productivity increased 10-23% as a result of compost application. No noticeable negative impact of OMW on the soil system was observed. Phenolic compound concentrations in the stabilised composts were comparable in the three studied mixtures (different sites) and averaged 0.24%. Considering previous results and this three year study, it has been observed that the benefit of these composts demonstrated the potential sustainable agronomic production of potato while using locally available recycled organic materials.     

Fuzzy control for the process of heat removal during the composting of agricultural waste

This paper shows the concept and preliminary test of the composting process control with fuzzy logic. The temperature in the compost heap during the process is greater than 80 °C. Because wastes of agricultural origin do not require hygienization, part of the heat can by retrieved, which lowers the temperature in the heap to 55 °C (this is also the optimum temperature for the composting process). The heat retrieved from a compost heap can be used in another place. Therefore, a composting system was developed in which the aeration rate and heat removal rate can be adjusted. There are two goals of this system: maximising the amount of the heat retrieved from the heap and minimising the duration of the composting process. In the preliminary experiments freshly mown grass with 50 % cabbage was used as the compost material. The results show that the fuzzy logic control system functions correctly with respect to calculations. During the study, a median 90 MJ of heat was produced by the bioreactor; the thermophilic phase was shortened to 12 days. There was also a reduction in the emission of ammonia.     

Evolution of organic matter during composting of different organic wastes assessed by CPMAS 13C NMR spectroscopy

In this paper, the evolution of organic matter (OM) during composting of different mixtures of various organic wastes was assessed by means of chemical analyses and CPMAS ¹³C NMR spectroscopy measured during composting. The trends of temperatures and C/N ratios supported the correct evolution of the processes. The CPMAS ¹³C NMR spectra of all composting substrates indicated a reduction in carbohydrates and an increase in aromatic, phenolic, carboxylic and carbonylic C which suggested a preference by microorganisms for easily degradable C molecules. The presence of hardly degradable pine needles in one of the substrates accounted for the lowest increase in alkyl C and the lowest reduction in carbohydrates and carboxyl C as opposite to another substrate characterized by the presence of a highly degradable material such as spent yeast from beer production, which showed the highest increase of the alkyl C/O-alkyl C ratio. The highest increase of COOH deriving by the oxidative degradation of cellulose was shown by a substrate composed by about 50% of plant residues. The smallest increases in alkyl C/O-alkyl C ratio and in polysaccharides were associated to the degradation of proteins and lipids which are major components of sewage sludge. Results obtained were related to the different composition of fresh organic substrates and provided evidence of different OM evolution patterns as a function of the initial substrate composition.     

Evaluation of the potential of applying composting/bioremediation techniques to wastes generated within the construction industry

The objective of the present study was to evaluate the viability of reducing landfill requirements to satisfy EC Landfill Directive requirements by applying composting/bioremediation techniques to the construction and demolition (C&D) industry waste stream at laboratory scale. The experimental study was carried out in nine test rigs to examine different wood mixtures; untreated timber, creosote treated timber and chromated copper arsenate (CCA) treated timber. Several experimental variables affecting the process were characterised and optimised. These include the best nitrogen additive and optimum moisture content required for composting. Poultry manure was found to be the best nitrogen additive. The optimum moisture content was decreased after the addition of poultry manure. The composting/bioremediation process was evaluated through monitoring the microbial activity, carbon dioxide emissions and toxicity examination of the composted product. A typical temperature profile suggested that untreated and CCA treated mix could be classified as hot composting whereas creosote treated mix could be classified as cold composting. The paper reports on the results obtained during this investigation.     

Management of agricultural biomass wastes: Preliminary study on characterization and valorisation in clay matrix bricks

In this work the feasibility of using woody agricultural biomass wastes as grapes and cherries seeds, sawdust, as pore forming agent, and sugar cane ash, as silica precursor, in bricks, were reported.Sawdust and grapes and cherries seeds, thanks to their organic substances content, during their combustion, bring an energetic support in the bricks firing phase and act as pore forming agent. Usually the addition of this kind of waste is limited to 10 wt.% in order to reach an equilibrium between positive (weight and shrinkage decrease and porosity increase) and negative (increase of water absorption and mechanical resistance decrease) effects. The results show that grapes and cherries seeds, added in a percentage of 5 wt.% to a brick formulation, have better influence with respect to the sawdust, maintaining the mechanical properties of the fired brick (950 °C), showing modulus of rupture around 21–23 MPa with a weight reduction of 3–10% (respect to the standard one). Regarding the sugar cane ash, the addition of 5 wt.% improves the mechanical properties (modulus of rupture around 27 MPa) and no weight decrease is observed. These results confirmed the role played by this kind of agricultural waste, which thanks to its high silica content (61 wt.%) is capable to demonstrate a filler and plasticity reducing effect on the brick bodies. Tests carried out highlighted that the addition of these by-products (5 wt.%) do not change negatively the main technological properties measured (water absorption, linear shrinkage, flexural resistance, etc.) and permit to hypothesize their use to obtain bricks with both insulating and higher mechanical properties using a pore agent forming or silica carrier alternative raw materials, respectively.     

Home composting versus industrial composting: Influence of composting system on compost quality with focus on compost stability

Stability is one of the most important properties of compost obtained from the organic fraction of municipal solid wastes. This property is essential for the application of compost to land to avoid further field degradation and emissions of odors, among others. In this study, a massive characterization of compost samples from both home producers and industrial facilities is presented. Results are analyzed in terms of chemical and respiration characterizations, the latter representing the stability of the compost. Results are also analyzed in terms of statistical validation. The main conclusion from this work is that home composting, when properly conducted, can achieve excellent levels of stability, whereas industrial compost produced in the studied facilities can also present a high stability, although an important dispersion is found in these composts. The study also highlights the importance of respiration techniques to have a reliable characterization of compost quality, while the chemical characterization does not provide enough information to have a complete picture of a compost sample.     

Mathematical model for carbon dioxide evolution from the thermophilic composting of synthetic food wastes made of dog food

The impacts of the aeration and the agitation on the composting process of synthetic food wastes made of dog food were studied in a laboratory-scale reactor. Two major peaks of CO(2) evolution rate were observed. Each peak represented an independent stage of composting associated with the activities of thermophilic bacteria. CO(2) evolutions known to correlate well with microbial activities and reactor temperatures were fitted successfully to a modified Gompertz equation, which incorporated three biokinetic parameters, namely, CO(2) evolution potential, specific CO(2) evolution rate, and lag phase time. No parameters that describe the impact of operating variables are involved. The model is only valid for the specified experimental conditions and may look different with others. The effects of operating parameters such as aeration and agitation were studied statistically with multivariate regression technique. Contour plots were constructed using regression equations for the examination of the dependence of CO(2) evolution potentials on aeration and agitation. In the first stage, a maximum CO(2) evolution potential was found when the aeration rate and the agitation parameter were set at 1.75 l/kg solids-min and 0.35, respectively. In the second stage, a maximum existed when the aeration rate and the agitation parameter were set at 1.8 l/kg solids-min and 0.5, respectively. The methods presented here can also be applied for the optimization of large-scale composting facilities that are operated differently and take longer time.