Large-scale direct shear testing of municipal solid waste

Large direct shear testing (300 mm × 300 mm box) of municipal solid waste (MSW) collected from a landfill located in the San Francisco Bay area was performed to gain insight on the shear response of MSW. The study investigated the effects of waste composition, confining stress, unit weight, and loading rate on the stress–displacement response and shear strength of MSW. The amount and orientation of the fibrous waste materials in the MSW were found to play a critical role. The fibrous material had little effect on the MSW’s strength when it was oriented parallel to the shear surface, as is typically the case when waste material is compressed vertically and then tested in a direct shear apparatus. Tests in which the fibrous material was oriented perpendicular to the horizontal shear surface produced significantly stronger MSW specimens. The test results indicate that confining stress and loading rate are also important factors. Based on 109 large-scale direct shear tests, the shear strength of MSW at low moisture contents is best characterized by cohesion = 15 kPa, friction angle = 36° at a normal stress of 1 atmosphere, and a decrease in the friction angle of 5° for every log-cycle increase in normal stress.     

Municipal solid waste effective stress analysis

The mechanical behavior of municipal solid waste (MSW) has attracted the attention of many researchers in the field of geo-environmental engineering in recent years and several aspects of waste mechanical response under loading have been elucidated. However, the mechanical response of MSW materials under undrained conditions has not been described in detail to date. The knowledge of this aspect of the MSW mechanical response is very important in cases involving MSW with high water contents, seismic ground motion and in regions where landfills are built with poor operation conditions. This paper presents the results obtained from 26 large triaxial tests performed both in drained and undrained conditions. The results were analyzed taking into account the waste particles compressibility and the deformation anisotropy of the waste samples. The waste particles compressibility was used to modify the Terzaghi effective stress equation, using the Skempton (1961) proposition. It is shown that the use of the modified effective stress equation led to much more compatible shear strength values when comparing Consolidated-Drained (CD) and Consolidated-Undrained (CU), results, explaining the high shear strength values obtained in CU triaxial tests, even when the pore pressure is almost equal to the confining stress.     

Mechanical behavior of typical hazardous waste and its influence on landfill stability during operation

The stability of hazardous waste (HW) landfill is a major security risk to the landfill environmental safety. The mechanical behavior of waste controls many aspects of landfill design and operation, including stability and settlement issues and the integrity of geosynthetic and liner components. This study presents the results of a laboratory experiment to learn the mechanical properties of HW collected from the Hangzhou HW landfill. Measured mechanical behavior was compared with results for municipal solid waste (MSW) to assess their discrepancies. The particle size of HW was analyzed by the sieving and hydrometer methods. Because HW comes primarily from industrial plants in the form of sludge or slag, their particle sizes are generally smaller than those of MSW. This study indicates that the shear strength parameters of HW are more sensitive to the methods of testing and calculation than those of MSW. Numerical simulations demonstrate that the safety factor of a landfill is affected by the mechanical properties of HW, especially cohesion and friction angle. Because of the lower particle size and wider compression ratio, compared to MSW, an HW landfill should be taken more care in its operational procedures so as to increase its stability.     

A design chart for estimation of horizontal displacement in municipal landfills

This paper describes the development of a design chart for the estimation of maximum horizontal displacement within a municipal landfill using the height and the side slope of the landfill. The design chart is based on the results of a finite element parametric study in which the behaviour of the municipal solid waste (MSW) was modeled using a non-linear elastic hyperbolic model. The model input parameters, i.e. non-linear stiffness, shear strength and unit weight of MSW, were obtained from laboratory testing data and an extensive stochastic numerical modelling exercise. Non-linear variations of unit weight as well as Young’s modulus of MSW with depth were incorporated in the finite element analyses. The validity of the design chart was assessed using field monitoring results from a large landfill located in Ontario, Canada.     

Drained response of municipal solid waste in large-scale triaxial shear testing

A comprehensive laboratory investigation was performed on municipal solid waste (MSW) from a landfill located in northern California using a large-scale triaxial (TX) apparatus. An improved, standardized waste specimen preparation method was developed and used to prepare 27 large-scale TX specimens (d=300mm, h=600-630mm). The effects of waste composition, confining stress, unit weight, loading rate, and stress path on the drained stress-strain response of MSW were investigated. Waste composition has a significant effect on its stress-strain response. The commonly observed upward curvature of the stress-strain response of specimens composed of larger-sized waste materials results from the fibrous constituents (primarily paper, plastic and wood) reinforcing the waste matrix. This effect is greatest when the MSW specimen is sheared across the long axis of the fibrous particles. Due to this significant strain hardening effect and waste's in situ stress state, a limiting strain failure criterion of 5% axial strain from the K(o) field consolidation state is judged to be most appropriate. Results from this test program and data from the literature indicate that the TX compression secant friction angle of MSW varies from 34° to 44°, with 39° as a best estimate, at a confining stress of one atmosphere (assuming c=0). The friction angle decreases as confining stress increases. The friction angles measured in this testing program are representative of failure surfaces that are oriented at an angle to the predominant orientation of the long axis of the fibrous waste particles. These friction angles are higher than those obtained in direct shear tests where shearing typically occurs parallel to the orientation of the fibrous waste particles.     

The effects of daily cover soils on shear strength of municipal solid waste in bioreactor landfills

Bioreactor landfills are operated to enhance refuse decomposition, gas production, and waste stabilization. The major aspect of bioreactor landfill operation is the recirculation of collected leachate back through the refuse mass. Due to the accelerated decomposition and settlement of solid waste, bioreactor landfills are gaining popularity as an alternative to the conventional landfill. The addition or recirculation of leachate to accelerate the waste decomposition changes the geotechnical characteristics of waste mass. The daily cover soils, usually up to 20–30% of total MSW volumes in the landfill, may also influence the decomposition and shear strength behavior of MSW. The objective of this paper is to study the effects of daily covers soils on the shear strength properties of municipal solid waste (MSW) in bioreactor landfills with time and decomposition. Two sets of laboratory-scale bioreactor landfills were simulated in a laboratory, and samples were prepared to represent different phases of decomposition. The state of decomposition was quantified by methane yield, pH, and volatile organic content (VOC). Due to decomposition, the matrix structure of the degradable solid waste component was broken down and contributed to a significant decrease in the reinforcing effect of MSW. However, the daily cover soil, a non-degradable constituent of MSW, remains constant. Therefore, the interaction between daily cover soil particles and MSW particles will affect shear strength behavior. A number of triaxial tests were performed to evaluate the shear strength of MSW. The test results indicated that the shear strength of MSW was affected by the presence of cover soils. The friction angle of MSW with the presence of cover soil is higher than the friction angle of MSW without any cover soils. The friction angle of MSW increased from 27° to 30° due to the presence of cover soils for Phase 1 samples. The increased strength was attributed to the friction nature of sandy soil that was used as daily covers soils. Therefore, the effects of cover soils on the shear strength properties of MSW should be evaluated and taken into consideration during stability analyses and design.     

Aging and compressibility of municipal solid wastes

The expansion of a municipal solid waste (MSW) landfill requires the ability to predict settlement behavior of the existing landfill. The practice of using a single compressibility value when performing a settlement analysis may lead to inaccurate predictions. This paper gives consideration to changes in the mechanical compressibility of MSW as a function of the fill age of MSW as well as the embedding depth of MSW. Borehole samples representative of various fill ages were obtained from five boreholes drilled to the bottom of the Qizhishan landfill in Suzhou, China. Thirty-one borehole samples were used to perform confined compression tests. Waste composition and volume-mass properties (i.e., unit weight, void ratio, and water content) were measured on all the samples. The test results showed that the compressible components of the MSW (i.e., organics, plastics, paper, wood and textiles) decreased with an increase in the fill age. The in situ void ratio of the MSW was shown to decrease with depth into the landfill. The compression index, Cc, was observed to decrease from 1.0 to 0.3 with depth into the landfill. Settlement analyses were performed on the existing landfill, demonstrating that the variation of MSW compressibility with fill age or depth should be taken into account in the settlement prediction.     

Constitutive model for municipal solid waste incorporating mechanical creep and biodegradation-induced compression

A constitutive model is proposed to describe the stress–strain behavior of municipal solid waste (MSW) under loading using the critical state soil mechanics framework. The modified cam clay model is extended to incorporate the effects of mechanical creep and time dependent biodegradation to calculate total compression under loading. Model parameters are evaluated based on one-dimensional compression and triaxial consolidated undrained test series conducted on three types of MSW: (a) fresh MSW obtained from working phase of a landfill, (b) landfilled waste retrieved from a landfill after 1.5 years of degradation, and (c) synthetic MSW with controlled composition. The model captures the stress–strain and pore water pressure response of these three types of MSW adequately. The model is useful for assessing the deformation and stability of landfills and any post-closure development structures located on landfills.     

Evolution of unsaturated hydraulic properties of municipal solid waste with landfill depth and age

Successful modeling of liquid and air flow and hence designing of liquid and air addition systems in the landfills are constrained by the lack of key parameters of unsaturated hydraulic properties of municipal solid waste (MSW), which are strongly dependent on the depth of burial and the degree of decomposition. In this study, water retention curves (WRC) of MSW are measured using pressure plate method on samples repacked according to the in situ unit weight measured during borehole sampling, representing the MSW in shallow, middle, and deep layers. The measured WRC of MSW is well-reproduced by the van Genuchten-Mualem model, and is used to predict the unsaturated hydraulic properties of MSW, including water retention characteristics and unsaturated hydraulic conductivity. The estimated model parameters are consistent with other studies, suggesting that the pressure plate method yields reproducible results. As the landfill depth and age increase, the overburden pressure, the highly decomposed organic matter and finer pore space increase, hence the capillary pressure increases, causing increases in air-entry values, field capacity and residual water content, and decreases in steepness of WRC and saturated water content. The unsaturated hydraulic properties of MSW undergo changes with landfill depth and age, showing more silt loam-like properties as the landfill age increases.     

Approach for the use of MSW settlement predictions in the assessment of landfill capacity based on reliability analysis

In the analysis and design of municipal solid waste (MSW) landfills, there are many uncertainties associated with the properties of MSW during and after MSW placement. Several studies are performed involving different laboratory and field tests to understand the complex behavior and properties of MSW, and based on these studies, different models are proposed for the analysis of time dependent settlement response of MSW. For the analysis of MSW settlement, it is very important to account for the variability of model parameters that reflect different processes such as primary compression under loading, mechanical creep and biodegradation. In this paper, regression equations based on response surface method (RSM) are used to represent the complex behavior of MSW using a newly developed constitutive model. An approach to assess landfill capacities and develop landfill closure plans based on prediction of landfill settlements is proposed. The variability associated with model parameters relating to primary compression, mechanical creep and biodegradation are used to examine their influence on MSW settlement using reliability analysis framework and influence of various parameters on the settlement of MSW are estimated through sensitivity analysis.     

Compositional effects on the dynamic properties of municipal solid waste

Large-scale cyclic simple shear tests were conducted on reconstituted specimens of municipal solid waste (MSW) collected from the Tri-Cities landfill in Fremont, California, USA. The influence of waste composition and compacted unit weight on the shear wave velocity, small-strain shear modulus, and strain-dependent shear modulus reduction and damping ratio curves of MSW was investigated in these tests. Modulus reduction and damping ratio curves were evaluated over a strain range of 0.01-3%. Specimens were reconstituted using 100%, 65%, and 35%, by weight, of the material that passed through a 20mm screen and four different levels of compaction effort. All specimens were consolidated under a normal stress of 75 kPa prior to testing. The test results show a very strong dependence of shear wave velocity and small strain shear modulus on unit weight. Unit weight also had an influence on modulus reduction and damping ratio. Waste composition had a very strong influence on damping and also influenced shear wave velocity, small strain shear modulus, and modulus reduction. The interrelationship between unit weight and waste composition made it difficult to separate out the effects of these parameters.     

Evaluation of the geotechnical properties of MSW in two Brazilian landfills

The characteristics of municipal solid waste (MSW) play a key role in many aspects of waste disposal facilities and landfills. Because most of a landfill is made up of MSW, the overall stability of the landfill slopes are governed by the strength parameters and physical properties of the MSW. These parameters are also important in interactions involving the waste body and the landfill structures: cover liner, leachate and gas collection systems. On the other hand, the composition of the waste, which affects the geotechnical behavior of the MSW, is dependent on a variety of factors such as climate, disposal technology, the culture and habits of the local community. It is therefore essential that the design and stability evaluations of landfills in each region be performed based on the local conditions and the geotechnical characteristic of the MSW. The Bandeirantes Landfill, BL, in São Paulo and the Metropolitan Center Landfill, MCL, in Salvador, are among the biggest landfills in Brazil. These two disposal facilities have been used for the development of research involving waste mechanics in recent years. Considerable work has been made in the laboratory and in the field to evaluate parameters such as water and organic contents, composition, permeability, and shear strength. This paper shows and analyzes the results of tests performed on these two landfills. The authors believe that these results could be a good reference for certain aspects and geotechnical properties of MSW materials in countries with similar conditions.     

A hybrid method for quasi-three-dimensional slope stability analysis in a municipal solid waste landfill

Limited space for accommodating the ever increasing mounds of municipal solid waste (MSW) demands the capacity of MSW landfill be maximized by building landfills to greater heights with steeper slopes. This situation has raised concerns regarding the stability of high MSW landfills. A hybrid method for quasi-three-dimensional slope stability analysis based on the finite element stress analysis was applied in a case study at a MSW landfill in north-east Spain. Potential slides can be assumed to be located within the waste mass due to the lack of weak foundation soils and geosynthetic membranes at the landfill base. The only triggering factor of deep-seated slope failure is the higher leachate level and the relatively high and steep slope in the front. The valley-shaped geometry and layered construction procedure at the site make three-dimensional slope stability analyses necessary for this landfill. In the finite element stress analysis, variations of leachate level during construction and continuous settlement of the landfill were taken into account. The "equivalent" three-dimensional factor of safety (FoS) was computed from the individual result of the two-dimensional analysis for a series of evenly spaced cross sections within the potential sliding body. Results indicate that the hybrid method for quasi-three-dimensional slope stability analysis adopted in this paper is capable of locating roughly the spatial position of the potential sliding mass. This easy to manipulate method can serve as an engineering tool in the preliminary estimate of the FoS as well as the approximate position and extent of the potential sliding mass. The result that FoS obtained from three-dimensional analysis increases as much as 50% compared to that from two-dimensional analysis implies the significance of the three-dimensional effect for this study-case. Influences of shear parameters, time elapse after landfill closure, leachate level as well as unit weight of waste on FoS were also investigated in this paper. These sensitivity analyses serve as the guidelines of construction practices and operating procedures for the MSW landfill under study.     

Interpretations of surface movements of a landfill built on steeply sloping ground. A cautionary case history

The surface of a municipal solid waste (MSW) landfill cell, built on steeply sloping ground, was discovered to be moving downhill. The movements were measured and considered by the owners to be alarming. In an attempt to stop the movement, the compacted soil stability berm at the toe of the cell was raised by 5 m in two stages. The rate of movement declined, but the waste surface continued to move. Eventually, the cell was not filled to its designed full level. The paper describes the design of the landfill cell and its underliner, as well as three independent investigations into the causes of the surface movement. The first two investigators assumed that the surface movements represented shear displacements at the interface of the geomembrane and its protective geo-fabric, and therefore that the cell was failing in shear. The third investigation, undertaken in preparation of evidence in a civil court case, 7 years later, concluded that the movements resulted from down-slope shear straining of the land-filled MSW. The later investigation concluded that the MSW cell had been, and is still shear-stable, and it points to differences in behaviour between MSW landfill slopes and comparable slopes in mine waste or natural soils.     

Parametric study of MSW landfill settlement model

A newly developed and validated constitutive model that accounts for primary compression and time-dependent mechanical creep and biodegradation is used for parametric study to investigate the effects of model parameters on the predicted settlement of municipal solid waste (MSW) with time. The model enables the prediction of stress strain response and yield surfaces for three components of settlement: primary compression, mechanical creep, and biodegradation. The MSW parameters investigated include compression index, coefficient of earth pressure at-rest, overconsolidation ratio, and biodegradation parameters of MSW. A comparison of the predicted settlements for typical MSW landfill conditions showed significant differences in time-settlement response depending on the selected model input parameters. The effect of lift thickness of MSW on predicted settlement is also investigated. Overall, the study shows that the variation in the model parameters can lead to significantly different results; therefore, the model parameter values should be carefully selected to predict landfill settlements accurately. It is shown that the proposed model captures the time settlement response which is in general agreement with the results obtained from the other two reported models having similar features.     

Geotechnical properties of municipal solid waste at different phases of biodegradation

This paper presents the results of laboratory investigation conducted to determine the variation of geotechnical properties of synthetic municipal solid waste (MSW) at different phases of degradation. Synthetic MSW samples were prepared based on the composition of MSW generated in the United States and were degraded in bioreactors with leachate recirculation. Degradation of the synthetic MSW was quantified based on the gas composition and organic content, and the samples exhumed from the bioreactor cells at different phases of degradation were tested for the geotechnical properties. Hydraulic conductivity, compressibility and shear strength of initial and degraded synthetic MSW were all determined at constant initial moisture content of 50% on wet weight basis. Hydraulic conductivity of synthetic MSW was reduced by two orders of magnitude due to degradation. Compression ratio was reduced from 0.34 for initial fresh waste to 0.15 for the mostly degraded waste. Direct shear tests showed that the fresh and degraded synthetic MSW exhibited continuous strength gain with increase in horizontal deformation, with the cohesion increased from 1 kPa for fresh MSW to 16–40 kPa for degraded MSW and the friction angle decreased from 35° for fresh MSW to 28° for degraded MSW. During the triaxial tests under CU condition, the total strength parameters, cohesion and friction angle, were found to vary from 21 to 57 kPa and 1° to 9°, respectively, while the effective strength parameters, cohesion and friction angle varied from 18 to 56 kPa and from 1° to 11°, respectively. Similar to direct shear test results, as the waste degrades an increase in cohesion and slight decrease in friction angle was observed. Decreased friction angle and increased cohesion with increased degradation is believed to be due to the highly cohesive nature of the synthetic MSW. Variation of synthetic MSW properties from this study also suggests that significant changes in geotechnical properties of MSW can occur due to enhanced degradation induced by leachate recirculation.     

Prediction of syngas quality for two-stage gasification of selected waste feedstocks

This paper compares the syngas produced from methane with the syngas obtained from the gasification, in a two-stage reactor, of various waste feedstocks. The syngas composition and the gasification conditions were simulated using a simple thermodynamic model. The waste feedstocks considered are: landfill gas, waste oil, municipal solid waste (MSW) typical of a low-income country, the same MSW blended with landfill gas, refuse derived fuel (RDF) made from the same MSW, the same RDF blended with waste oil and a MSW typical of a high-income country. Energy content, the sum of H2 and CO gas percentages, and the ratio of H2 to CO are considered as measures of syngas quality. The simulation shows that landfill gas gives the best results in terms of both H2+CO and H2/CO, and that the MSW of low-income countries can be expected to provide inferior syngas on all three quality measures. Co-gasification of the MSW from low-income countries with landfill gas, and the mixture of waste oil with RDF from low-income MSW are considered as options to improve gas quality.     

Soil reinforcement with recycled carpet wastes.

A root or fibre-reinforced soil behaves as a composite material in which fibres of relatively high tensile strength are embedded in a matrix of relatively plastic soil. Shear stresses in the soil mobilize tensile resistance in the fibres, which in turn impart greater strength to the soil. A research project has been undertaken to study the influence of synthetic fibrous materials for improving the strength characteristics of a fine sandy soil. One of the main objectives of the project is to explore the conversion of fibrous carpet waste into a value-added product for soil reinforcement. Drained triaxial tests were conducted on specimens, which were prepared in a cylindrical mould and compacted at their optimum water contents. The main test variables included the aspect ratio and the weight percentage of the fibrous strips. The results clearly show that fibrous inclusions derived from carpet wastes improve the shear strength of silty sands. A model developed to simulate the effect of the fibrous inclusions accurately predicts the influence of strip content, aspect ratio and confining pressure on the shear strength of reinforced sand.     

Geotechnical properties of fresh municipal solid waste at Orchard Hills Landfill, USA

This paper presents the results of a laboratory investigation to determine the geotechnical properties of fresh municipal solid waste (MSW) collected from the working phase of Orchard Hills Landfill located in Davis Junction (Illinois, USA). Laboratory testing was conducted on shredded MSW to determine the compaction, hydraulic conductivity, compressibility, and shear strength properties at in-situ gravimetric moisture content of 44%. In addition, the effect of increased moisture content during leachate recirculation on compressibility and shear strength of MSW was also investigated by testing samples with variable gravimetric moisture contents ranging from 44% to 100%. Based on Standard Proctor tests, a maximum dry density of 420 kg/m(3) was observed at 70% optimum moisture content. The hydraulic conductivity varied in a wide range of 10(-8)-10(-4)m/s and decreased with increase in dry density. Compression ratio values varied in a close range of 0.24-0.33 with no specific trend with the increase in moisture content. Based on direct shear tests, drained cohesion varied from 31 to 64 kPa and the drained friction angle ranged from 26 to 30 degrees. Neither cohesion nor friction angle demonstrated any correlation with the moisture content, within the range of moisture contents tested. The consolidated undrained triaxial shear tests on saturated MSW showed the total strength parameters (c and phi) to be 32 kPa and 12 degrees, and the effective strength parameters (c' and phi') to be 38 kPa and 16 degrees. The angle of friction (phi) decreased and cohesion (c) value increased with the increase in strain. The effective cohesion (c') increased with increase in strain; however, the effective angle of friction (phi') decreased first and then increased with the increase in strain. Such strain-dependent shear strength properties should be properly accounted in the stability analysis of bioreactor landfills.