Separability studies of construction and demolition waste recycled sand

The quality of recycled aggregates from construction and demolition waste (CDW) is strictly related to the content of porous and low strength phases, and specifically to the patches of cement that remain attached to the surface of natural aggregates. This phase increases water absorption and compromises the consistency and strength of concrete made from recycled aggregates. Mineral processing has been applied to CDW recycling to remove the patches of adhered cement paste on coarse recycled aggregates. The recycled fine fraction is usually disregarded due to its high content of porous phases despite representing around 50% of the total waste.This paper focus on laboratory mineral separability studies for removing particles with a high content of cement paste from natural fine aggregate particles (quartz/feldspars). The procedure achieved processing of CDW by tertiary impact crushing to produce sand, followed by sieving and density and magnetic separability studies. The attained results confirmed that both methods were effective in reducing cement paste content and producing significant mass recovery (80% for density concentration and 60% for magnetic separation). The production of recycled sand contributes to the sustainability of the construction environment by reducing both the consumption of raw materials and disposal of CDW, particularly in large Brazilian centers with a low quantity of sand and increasing costs of this material due to long transportation distances.     

Life cycle inventory of recycled aggregates derived from construction and demolition waste

Journal of Material Cycles and Waste Management - This study is performed to identify environmental aspects that can be improved during the derivation of recycled aggregates (RAs) from construction...     

Life cycle based risk assessment of recycled materials in roadway construction

This paper uses a life-cycle assessment (LCA) framework to characterize comparative environmental impacts from the use of virgin aggregate and recycled materials in roadway construction. To evaluate site-specific human toxicity potential (HTP) in a more robust manner, metals release data from a demonstration site were combined with an unsaturated contaminant transport model to predict long-term impacts to groundwater. The LCA determined that there were reduced energy and water consumption, air emissions, Pb, Hg and hazardous waste generation and non-cancer HTP when bottom ash was used in lieu of virgin crushed rock. Conversely, using bottom ash instead of virgin crushed rock increased the cancer HTP risk due to potential leachate generation by the bottom ash. At this scale of analysis, the trade-offs are clearly between the cancer HTP (higher for bottom ash) and all of the other impacts listed above (lower for bottom ash). The site-specific analysis predicted that the contaminants (Cd, Cr, Se and Ag for this study) transported from the bottom ash to the groundwater resulted in very low unsaturated zone contaminant concentrations over a 200 year period due to retardation in the vadose zone. The level of contaminants predicted to reach the groundwater after 200 years was significantly less than groundwater maximum contaminant levels (MCL) set by the US Environmental Protection Agency for drinking water. Results of the site-specific contaminant release estimates vary depending on numerous site and material specific factors. However, the combination of the LCA and the site specific analysis can provide an appropriate context for decision making. Trade-offs are inherent in making decisions about recycled versus virgin material use, and regulatory frameworks should recognize and explicitly acknowledge these trade-offs in decision processes.     

Sustainable management measures for healthcare waste in China

This paper discusses actions aimed at sustainable management of healthcare wastes (HCW) in China, taking into account the current national situation in this field, as well as the requirements deriving from the Stockholm Convention on Persistent Organic Pollutants and the WHO recommendations. By the end of 2005, there were 149 low-standard HCW disposal facilities in operation in China, distributed throughout different areas. According to the National Hazardous Waste and Healthcare Waste Disposal Facility Construction Plan, 331 modern, high-standard, centralized facilities will be built up in China in municipal level cities. Although incineration is still the main technical option for HCW disposal in China, it is expected that, especially for medium and small size facilities, non-incineration technologies will develop quickly and will soon become the main technical option. The basic management needs – both from the point of view of pollution control and final disposal – have been defined, and a system of technical and environmental standards has been formulated and implemented; however, there are still some shortages. This is particularly true when considering the best available techniques and best environmental practices developed under the Stockholm Convention, with which the present technological and managing situations are not completely compliant. In this framework, the lifecycle (from generation to final disposal of wastes) of HCW and holistic approaches (technology verification, facilities operation, environmental supervision, environmental monitoring, training system, financial mechanism, etc.) towards HCW management are the most important criteria for the sustainable and reliable management of HCW in China.     

Sustainable waste management in Africa through CDM projects

Only few Clean Development Mechanism (CDM) projects (traditionally focussed on landfill gas combustion) have been registered in Africa if compared to similar developing countries. The waste hierarchy adopted by many African countries clearly shows that waste recycling and composting projects are generally the most sustainable. This paper undertakes a sustainability assessment for practical waste treatment and disposal scenarios for Africa and makes recommendations for consideration. The appraisal in this paper demonstrates that mechanical biological treatment of waste becomes more financially attractive if established through the CDM process. Waste will continue to be dumped in Africa with increasing greenhouse gas emissions produced, unless industrialised countries (Annex 1) fund carbon emission reduction schemes through a replacement to the Kyoto Protocol. Such a replacement should calculate all of the direct and indirect carbon emission savings and seek to promote public–private partnerships through a concerted support of the informal sector.     

Estimation of construction waste generation and management in Thailand

This study examines construction waste generation and management in Thailand. It is estimated that between 2002 and 2005, an average of 1.1 million tons of construction waste was generated per year in Thailand. This constitutes about 7.7% of the total amount of waste disposed in both landfills and open dumpsites annually during the same period. Although construction waste constitutes a major source of waste in terms of volume and weight, its management and recycling are yet to be effectively practiced in Thailand. Recently, the management of construction waste is being given attention due to its rapidly increasing unregulated dumping in undesignated areas, and recycling is being promoted as a method of managing this waste. If effectively implemented, its potential economic and social benefits are immense. It was estimated that between 70 and 4,000 jobs would have been created between 2002 and 2005, if all construction wastes in Thailand had been recycled. Additionally it would have contributed an average savings of about 3.0 x 10(5) GJ per year in the final energy consumed by the construction sector of the nation within the same period based on the recycling scenario analyzed. The current national integrated waste management plan could enhance the effective recycling of construction and demolition waste in Thailand when enforced. It is recommended that an inventory of all construction waste generated in the country be carried out in order to assess the feasibility of large scale recycling of construction and demolition waste.     

Environmental management of construction and demolition waste in Kuwait

There is an increasing pressure on the construction industry to reduce costs and improve the quality of our environment. The fact is that both of these goals can be achieved at the same time. Although construction and demolition (C&D) constitutes a major source of waste in terms of volume and weight, its management and recycling efforts have not yet seen the light in Kuwait. This study focuses on recycling efforts leading to the minimization of the total C&D waste that is currently landfilled in Kuwait. This paper presents the current status of C&D waste disposal system in Kuwait and identifies the potential problems to the environment, people and economy. Then, it investigates alternative solutions to manage and control this major type of waste in an economically efficient and environmentally safe manner. Next, the paper describes the feasibility of establishing a C&D waste recycling facility in Kuwait. It concludes by highlighting the major benefits and bottleneck problems with such a recycling facility.     

Sustainable waste management in the Indian mining industry.

One of the important sectors that contribute to the national economy is the mining sector. During the mining of minerals and ores, waste materials in the form of overburden are generated. As these are not useful to the mine owners, they may be inappropriately disposed of into the environment, posing serious threat to the environment in the form of land degradation, water and air pollution. The present paper discusses the existing status of waste generation, its characteristics and the disposal methods being adopted in India. Impacts associated with waste disposal practices together with preventive measures for waste disposal are also discussed. Finally, strategies for improvements in existing waste management and for incorporating the same in the overall development plan for the mines are suggested.     

A sustainable production model for waste management with uncertain scrap and recycled material

Journal of Material Cycles and Waste Management - The studies highlightthat only one billion tons were obtained out of four billion tons of solid waste in the world and small value recovered out of...     

Sustainable solutions for solid waste management in Southeast Asian countries

Human activities generate waste and the amounts tend to increase as the demand for quality of life increases. Today’s rate in the Southeast Asian Nations (ASEANs) is alarming, posing a challenge to governments regarding environmental pollution in the recent years. The expectation is that eventually waste treatment and waste prevention approaches will develop towards sustainable waste management solutions. This expectation is for instance reflected in the term ‘zero emission systems’. The concept of zero emissions can be applied successfully with today’s technical possibilities in the agro-based processing industry. First, the state-of-the-art of waste management in Southeast Asian countries will be outlined in this paper, followed by waste generation rates, sources, and composition, as well as future trends of waste. Further on, solutions for solid waste management will be reviewed in the discussions of sustainable waste management. The paper emphasizes the concept of waste prevention through utilization of all wastes as process inputs, leading to the possibility of creating an ecosystem in a loop of materials. Also, a case study, focusing on the citrus processing industry, is displayed to illustrate the application of the aggregated material input–output model in a widespread processing industry in ASEAN. The model can be shown as a closed cluster, which permits an identification of opportunities for reducing environmental impacts at the process level in the food processing industry. Throughout the discussion in this paper, the utilization of renewable energy and economic aspects are considered to adapt to environmental and economic issues and the aim of eco-efficiency. Additionally, the opportunities and constraints of waste management will be discussed.     

Recycling of construction and demolition waste materials: a chemical-mineralogical appraisal

Building activity is currently demanding remarkable amounts of inert materials (such as gravel and sand) that are usually provided by alluvial sediments. The EU directives and Italian Legislation are encouraging the re-use of construction and demolition waste provided by continuous urban redevelopment. The re-utilisation of building waste is a relatively new issue for Italy: unfortunately the employment of recycled inert materials is still limited to general bulk and drainage fills, while a more complete re-evaluation is generally hampered by the lack of suitable recycling plants. In this paper, chemical-mineralogical characterization of recycled inert materials was carried out after preliminary crushing and grain-size sorting. XRF and XRD analysis of the different grain-size classes allowed us to recognise particular granulometric classes that can be re-utilised as first-order material in the building activity. Specifically, the presented chemical-mineralogical appraisal indicates that the recycled grain-size fraction 0.6-0.125 mm could be directly re-employed in the preparation of new mortar and concrete, while finer fractions could be considered as components for industrial processing in the preparation of cements and bricks/tiles.     

Utilization of CO2 into recycled construction materials: A systematic literature review

Journal of Material Cycles and Waste Management - In recent years, as the concepts of “zero waste” and “low carbon” gradually become hot topics, the unparalleled generation...     

A framework for understanding waste management studies in construction

During the past decades, construction and demolition (C&D) waste issues have received increasing attention from both practitioners and researchers around the world. A plethora of research relating to C&D waste management (WM) has been published in scholarly journals. However, a comprehensive understanding of the C&D WM research is somehow absent in spite of its proliferation. The aim of this paper is to develop a framework that helps readers understand the C&D WM research as archived in selected journals. Papers under the topic of C&D WM are retrieved based on a set of rigorous procedures. The information of these papers is then analyzed with the assistance of the Qualitative Social Research (QSR) software package NVivo. A framework for understanding C&D WM research is created based on the analytic results. By following the framework, a bibliometric analysis of research in C&D WM is presented, followed by an in-depth literature analysis. It is found that C&D generation, reduction, and recycling are the three major topics in the discipline of C&D WM. Future research is recommended to (a) investigate C&D waste issues in wider scopes including design, maintenance and demolition, (b) develop a unified measurement for waste generation so that WM performance can be compared across various economies, and (c) enhance effectiveness of WM approaches (e.g. waste charging scheme) based on new WM concepts (e.g. Extended Producer Responsibility). In addition to the above research findings, the approach for producing the research framework can be useful references for other studies which attempt to understand the research of a given discipline.     

Removal of mixed contaminants by Fe0-based biobarrier in flow-through columns using recycled waste materials

The present study investigated the reactivity and ability of permeable reactive barriers [zero-valent iron (ZVI)-barrier plus biobarrier) to remove various contaminants (Cd, As, Zn, Cu, Mn, Cr, NO₃ ⁻, NH₄ ⁺, and COD_cr) from synthetic leachate. Two different reactive materials were used in this study, namely ZVI and autoclaved lightweight concrete (ALC). After 90 days of column operation, the contaminant profiles were determined along the length of the columns. The heavy metals were extensively removed in the bio-ALC and sequential barriers (ZVI plus bio-ALC), however the removal efficiencies for the heavy metals Zn and Cr in the ALC and bio-ALC barriers were comparatively low. Nitrate was completely removed (>99.9%) in the ALC, bio-ALC, and sequential barriers. More than 50% of the produced ammonium and organic materials were removed in the biologically reactive zone of the sequential barriers. The results of the present study suggest that sequential barriers are one of the best solutions for in situ remediation and that they can be applied to clean up the leachate released from landfills.     

Preliminary study for the management of construction and demolition waste

This paper refers to the management of the construction and demolition (C&D) waste since, according to the EU Waste Strategy, C&D waste is considered to be one of the priority waste streams and appropriate actions need to be taken with respect to its effective management. Initially, the paper presents the state-of-the-art of the problem of C&D waste, including the amount and composition of C&D waste in EU countries, differences in the characteristics of this waste stream depending on its origin, as well as collection and management practices that are applied. A methodology is described for the estimation of the quantities of the waste stream under examination, since in most cases quantitative primary data is not available. Next, the fundamentals for the development of an integrated scheme for the management of C&D waste are presented and discussed, such as appropriate demolition procedures and location of waste management (off-site waste management, on-site waste management, direct on-site recovery, centralized on-site recovery). Finally, taking into consideration all relevant parameters, alternative systems that could be applied for the management of the C&D waste are suggested.     

A Spanish model for quantification and management of construction waste

Currently, construction and demolition waste (C&D waste) is a worldwide issue that concerns not only governments but also the building actors involved in construction activity. In Spain, a new national decree has been regulating the production and management of C&D waste since February 2008. The present work describes the waste management model that has inspired this decree: the Alcores model implemented with good results in Los Alcores Community (Seville, Spain). A detailed model is also provided to estimate the volume of waste that is expected to be generated on the building site. The quantification of C&D waste volume, from the project stage, is essential for the building actors to properly plan and control its disposal. This quantification model has been developed by studying 100 dwelling projects, especially their bill of quantities, and defining three coefficients to estimate the demolished volume (CT), the wreckage volume (CR) and the packaging volume (CE). Finally, two case studies are included to illustrate the usefulness of the model to estimate C&D waste volume in both new construction and demolition projects.     

Sustainable waste management through eco-entrepreneurship: an empirical study of waste upcycling eco-enterprises in Sri Lanka

Journal of Material Cycles and Waste Management - The key aim of a transition to a Green Economy is to enable economic growth and investment while increasing environmental quality and social...     

Sustainable solid waste management: An integrated approach for Asian countries

Solid waste management (SWM) has been an integral part of every human society. The approaches for SWM should be compatible with the nature of a given society, and, in this regard, Asian countries are no exception. In keeping with global trends, the systems are being oriented to concentrate on sustainability issues; mainly through the incorporation of 3R (reduce, reuse and recycle) technologies. However, degree and nature of improvements toward sustainability are varying and depend on the economic status of a country. High-income countries like Japan and South Korea can afford to spend more to incorporate 3R technologies. Most of the latest efforts focus on “Zero Waste” and/or “Zero Landfilling” which is certainly expensive for weaker economies such as those of India or Indonesia. There is a need to pragmatically assess the expectations of SWM systems in Asian countries. Hence, in this paper, we analyze the situation in different Asian countries, and explore future trends. We conceptually evaluate issues surrounding the sustainability of SWM. We propose a multi-pronged integrated approach for improvement that achieves sustainable SWM in the context of national policy and legal frameworks, institutional arrangement, appropriate technology, operational and financial management, and public awareness and participation. In keeping with this approach, a generic action plan has been proposed that could be tailored to suit a situation in a particular country. Our proposed concept and action plan framework would be useful across a variety of country-specific scenarios.     

Application of the US decision support tool for materials and waste management

The US Environmental Protection Agency (US EPA) launched the Resource Conservation Challenge (RCC) in 2002 to help reduce waste and move towards more sustainable resource consumption. The objective of the RCC is to help communities, industries, and the public think in terms of materials management rather than waste disposal. Reducing cost, finding more efficient and effective strategies to manage municipal waste, and thinking in terms of materials management requires a holistic approach that considers life-cycle environmental tradeoffs. The US EPA's National Risk Management Research Laboratory has led the development of a municipal solid waste decision support tool (MSW-DST). The computer software can be used to calculate life-cycle environmental tradeoffs and full costs of different waste management or materials recovery programs. The environmental methodology is based on the use of life-cycle assessment and the cost methodology is based on the use of full-cost accounting. Life-cycle inventory (LCI) environmental impacts and costs are calculated from the point of collection, handling, transport, treatment, and disposal. For any materials that are recovered for recycling, offsets are calculated to reflect potential emissions savings from use of virgin materials. The use of the MSW-DST provides a standardized format and consistent basis to compare alternatives. This paper provides an illustration of how the MSW-DST can be used by evaluating ten management strategies for a hypothetical medium-sized community to compare the life-cycle environmental and cost tradeoffs. The LCI results from the MSW-DST are then used as inputs into another US EPA tool, the Tool for the reduction and assessment of chemical and other environmental impacts, to convert the LCI results into impact indicators. The goal of this paper is to demonstrate how the MSW-DST can be used to identify and balance multiple criteria (costs and environmental impacts) when evaluating options for materials and waste management. This type of approach is needed in identifying strategies that lead to reduced waste and more sustainable resource consumption. This helps to meet the goals established in the US EPA's Resource Conservation Challenge.