Remediation of PCB‐Contaminated Soil Using Extraction and Destruction: Bench‐Scale Test

Polychlorinated biphenyls (PCBs) are a persistent environmental issue worldwide. This study summarizes the results obtained from a bench‐scale test of remediating PCB‐impacted soil. The research aimed to evaluate the effectiveness of extracting the PCB Aroclor 1260 from soil, transferring it to a liquid matrix, and then treating the PCB‐containing liquid using an Activated Metal Treatment System, a technology developed by NASA based on zero valent magnesium (ZVMg). The soil was from a former electrical plant area impacted by PCBs. The initial concentration of untreated soil contained an average of 4.7 ± 0.15 mg/kg of Aroclor 1260. The results showed that the mass transfer phenomena is possible using ethanol as a liquid matrix, reaching transfer results up to 93 percent. The ZVMg enabled the destruction of the Aroclor 1260, which reached 20 percent without any buildup of undesirable by‐products, such as less chlorinated PCBs.  ©2016 Wiley Periodicals, Inc.     

The effect of solvent concentration on the use of palladized-iron for the step-wise dechlorination of polychlorinated biphenyls in soil extracts

This report describes the application of palladized iron (Pd/Fe) to the dechlorination of polychlorinted biphenyls (PCBs) at ambient temperature. Experiments supported by congener-specific analyses demonstrated that dechlorination occurs in a step-wise fashion with the meta-chlorines being more reactive than ortho-chlorines. Over the course of the laboratory experiments, complete conversion to biphenyl was observed. The process was also tested with PCBs dissolved in high (40-60%) concentrations of ethanol and isopropanol as a means of simulating solutions generated by commercial soil and solid waste extraction processes. The reaction rate was sensitive to the percentage of solvent but complete dechlorination was still indicated. Tests with soil extracts from a contaminated site demonstrated that there were no apparent interferences from asphalt and other miscellaneous debris. Short-duration tests with highly contaminated PCB solutions from a hazardous waste site demonstrated efficient dechlorination although there was a reduction in reaction rate with time.     

Bacteria Degrading PCBs and CBs Isolated from Long-Term PCB Contaminated Soil

Bacteria able to degrade polychlorinated biphenyls (PCBs) and chlorobenzoic acids (CBs) were isolated from soil that had been contaminated with PCBs for 15–30 years. Contaminated soil in which PCB content ranged between 10–470 mg/kg was naturally vegetated with different plants including ash (Fraxinus excelsior), birch (Betula pendula), black locust (Robinia pseudoacacia), Austrian pine (Pinus nigra) and goat willow (Salix caprea) trees as well as a variety of grasses and forbs. Bacteria able to use biphenyl as a sole source of carbon and energy were found in the root zone of all plants, but occurred in the largest numbers beneath pine and black locust. Bacteria able to degrade chlorobenzoic acids were isolated from the same location contaminated with PCBs. Strains that were taxonomically identified by 16S rDNA as Pandoraea were able to use 2-CB, 3-CB, 2,3-CB, 2,5-CB as sole carbon sources, and the strain Arthrobacter utilised 4-CB.     

Persistence of the De-Icing Additive Benzotriazole at an Abandoned Airport

The environmental fate of many of the additives in the deicing agents used at airports is poorly understood. One and two years after deicing activities ceased, soil and groundwater samples were taken at an abandoned airport. Benzotriazole (BT), a corrosion and flame inhibitor, was found in low concentrations in soils along runways (mean 0.33 mg/kg), at a snow disposal site (0.66 mg/kg), as well as in sediments of a drainage ditch (13 mg/kg). Locally, high BT concentrations were found in the groundwater below the deicing pad, the regeneration plant and the snow disposal site (1.2 to 1100 g/l). Methyl substituted triazoles or tolytriazoles (MeBT) were found in concentrations less than 10% of the BT concentration. Propylene glycol was not detected in soil samples and in only one of the groundwater samples. Microtox tests of the water samples revealed no acute toxic response, however a reduction in nitrification rate was observed (14–43%). The nitrification response could not be related directly to the BT concentration in the samples, although samples with a high BT concentration showed the largest reduction in nitrification rate. BT showed very little sorption in various soil matrices, only peat and compost with a high organic carbon content showed significant sorption. Sorption could be best described using a Freundlich isotherm. These results indicate a high mobility and possibly long persistence of BT in soil and groundwater, which may be attributed to the absence of microbial degradation of BT.     

A comparison of mesophilic composting and unamended land treatment for the bioremediation of aged tar residues in soil

A field study was conducted to compare the effectiveness of land treatment and mesophilic composting in removing aged polycyclic aromatic hydrocarbons (PAH) from soil. The soil composting treatment, which had 20 percent (w/w) fresh organic matter incorporated into the soil, reached mesophilic temperatures of 45 to 50°C at week 3–4 and was effective in reducing PAH from 2240 mg/kg to 120 mg/kg after 224 days of treatment. Conventional land treatment with and without added cow manure (5 percent w/w) was less effective in removing the PAH from the soil than was the mesophilic soil composting treatment. In a parallel laboratory trial, PAH concentrations were reduced below 500 mg/kg (the target cleanup concentration for the site) when the contaminated soil was amended with 20 to 30 percent (w/w) fresh organic matter after 186 days of treatment. PAH degradation was lower in the laboratory trial compared with the field trial and no self-heating of soil was demonstrated in the laboratory. Based on the relatively high total heterotrophic and naphthalene-degrading microbial populations in the nonsterile treatments, it was apparent that the absence of microorganisms was unlikely to have limited the biodegradation of PAH in the current study. Fresh organic matter amendments of green tree waste and cow manure, regular mixing of the compost, and maintenance of moisture by regular watering were critical factors in achieving the target PAH concentrations.     

Photodegradation of tetraphenyltin contained in polychlorinated biphenyl-based transformer oil simulants in alkaline 2-propanol solution

The photodegradation of tetraphenyltin (TePT) contained in polychlorinated biphenyl (PCB)-based transformer oil simulants by ultraviolet (UV) irradiation in alkaline 2-propanol solutions was examined. In the absence of PCBs, the TePT level fell to below 1% of the initial concentration within 30 min. In the absence of both PCBs and an alkali, the concentrations of tri-, di-, and monophenyltins initially increased to a few milligrams per liter, and then reduced to below the detection limits within 90 min. The addition of an alkali to the reaction solution slightly accelerated the photodecomposition of TePT. The decomposition of other phenyltins (PTs) was also accelerated. When PCBs with concentrations of approximately 80 times the initial TePT concentration were added, only a small fraction of the TePT decomposed within 100 min. Moreover, the levels of PTs did not change during irradiation. TePT and other PTs did decompose when the level of PCBs was reduced to the same concentration as that of TePT; however, the decomposition rates were slower than those in the absence of PCBs. In the actual treatment process, TePT and other PTs in PCB-based transformer oil are decomposed by catalytic reduction, which is used after UV irradiation. Therefore, in the actual treatment of PCB-based transformer oil wastes, pollution due to PTs can be prevented.     

Composition and management of rechargeable electric torch wastes in Ibadan,Nigeria

The consumption, disposal, material and chemical compositions of rechargeable electric torch wastes (RETWs) were investigated in Ibadan, Nigeria. Twenty-five RETWs of ten models were collected and disassembled. Their battery electrodes (BEs) and printed circuit boards (PCBs) were acid digested and leached using United States Environmental Protection Agency (USEPA) method 3050B and USEPA Method 1311, respectively. The digests and extracts were analysed for total and extractable Pb, Cd, Cr and Ni using atomic absorption spectrophotometer. The US Test method (CPSC-CH-E 1002-08) was used for digestion of the plastic components. Two hundred questionnaires were distributed to users in Ibadan to determine their usage of RETs and their management when spent. The results indicated that BEs contributed the highest percentage (44 %) component, followed by plastic (38 %). Other components include metal, PCBs, glass and wire. Of the respondents, 61.9 % dispose their spent torches in dumpsites. The mean ± SD concentrations of Pb, Cd, Cr and Ni in the BEs were 500 ± 109 g/kg, 3.94 ± 6.84 mg/kg, 0.33 ± 0.88 mg/kg, 1.68 ± 0.74 mg/kg respectively; in the PCBs, they were 684 ± 42 g/kg, 13.7 ± 17.8 mg/kg, 13.5 ± 10.2 mg/kg and 193 ± 437 mg/kg; and in the plastics, they were 14.1 g/kg, 5.33 mg/kg, 17 mg/kg, and 4.67 mg/kg respectively. The extractable Pb in BE (2670 mg/L) and PCBs (235 mg/L) exceeded the Toxicity Characteristics Leaching Procedure (TCLP) limit of 5 mg/L. RETWs present potential environmental problems in the absence of effective recycling.     

硫酸盐还原菌原位修复六价铬污染土壤

以FeSO₄化学还原法为对照,开展硫酸盐还原菌原位修复铬污染土壤的田间试验研究。试验结果表明:微生物法处理后,土壤中Cr(Ⅵ)含量从6.48 mg/kg降至0.95 mg/kg,下降率为85.33%,修复后的土地质量符合国家一类建设用地的标准;土壤浸出液中Cr(Ⅵ)质量浓度从0.162 mg/L降至0.004 mg/L,下降率为97.53%;土壤中硫酸根浓度略有降低,硫酸盐还原菌的丰度显著增加。微生物原位修复铬污染土壤的效果好于化学还原法。     

Safety management by use of laser mass spectrometry of polychlorinated biphenyls (PCBs) in the processed gas and work environment of a PCB disposal plant

This study demonstrates the applicability of laser mass spectrometry for safety management of the processed gas and the work environment in a polychlorinated biphenyl (PCB) disposal plant. By utilization of laser ionization/ion trapping storage/time-of-flight mass spectrometry (LI-IT-TOFMS), we analyzed gaseous PCBs from scrap capacitors with on-line detection. It was confirmed that few contaminants were detected in the spectrum. By the effect of laser-induced selective ionization, it was considered that there was little interference with the mass range of PCBs. The accuracy of LI-IT-TOFMS when analyzing environmental gas was almost the same as that for the PCB standard gas. It was possible to perform on-line analysis of the work environment for over 2000 h (120 000 data points). LI-IT-TOFMS was thus shown to be a very useful method for ensuring the safety of the work environment in disposal plants for PCBs.     

Novel pilot-scale washing process and equipment for removing Cr(VI) from contaminated soil

In this study, a novel horizontal rotating soil washing process and equipment were developed and tested for pilot-scale remediation of soils from a site polluted by chromium ore process residue. Operating parameters, including cylinder rotational velocity, cylinder tilt angle, heating temperature and liquid/soil ratio, were investigated. The Taguchi method was used for the experiment design, and the standard L16 orthogonal array with four parameters and four levels was selected for optimising the operating parameters. Optimal removal efficiency was achieved at cylinder rotational velocity of 2.5 rpm, cylinder tilt angle of 2.6°, heating temperature of 200 °C and liquid/soil ratio of 8. The efficiency of citric acid as an extractant in the novel process was compared with that of water. The analysis of the residual Cr(VI) concentration of the soil shows that citric acid could efficiently remove 22.89 % more Cr(VI) than water in one-stage washing. The residual Cr(VI) concentration in the soil after the three-stage washing is as low as 26.16 mg/kg, which meets the screening levels for soil environmental risk assessment of sites in Beijing City (30 mg/kg). Further study is currently underway to optimise the novel process and equipment for commercial-scale use.     

Comparative evaluation of demonstration testing of two PCB detoxification technologies

This paper presents a summary of the comparative analysis of two polychlorinated biphenyl (PCB) detoxification technologies that were evaluated in pilot scale equipment. Two treatment technologies, base catalyzed decomposition (BCD) and gas phase chemical reduction, treated materials removed from the PCB landfill in Warren County, North Carolina. There has been a remarkable amount of public opposition to this landfill. Very stringent performance criteria for soil cleanup of PCBs and dioxins and for air emissions from the treatment equipment were used, along with a number of other factors to evaluate the two technologies. The BCD technology was selected as the best performing one for this project.     

铬污染土壤处理中的铬含量及形态变化

采用FeSO_4和Na_2S作为还原剂处理铬污染紫色土壤,研究了还原过程中铬的含量及形态的变化。实验结果表明:当FeSO_4加入量为1.5%(w,下同)时,浸出Cr(Ⅵ)含量由(1 745.13±27.93)mg/kg降至(17.65±2.28)mg/kg,浸出总铬含量由(1 768.83±57.24)mg/kg降至(69.79±8.61)mg/kg,铬形态由水溶+碳酸盐结合态转变到较稳定的铁锰结合态;当Na_2S加入量为0.4%时,浸出Cr(Ⅵ)含量由(1 745.13±27.93)mg/kg降至(25.50±0.12)mg/kg,浸出总铬含量由(1 768.83±57.24)mg/kg降至(410.87±12.83)mg/kg,铬形态由水溶+碳酸盐结合态转变到铁锰结合态和有机结合态。     

Occurrence of organic pollutants in recovered soil fines from construction and demolition waste

The objective of this study was to characterize recovered soil fines from construction and demolition (C&D) waste recycling facilities for trace organic pollutants. Over a period of 18 months, five sampling trips were made to 14 C&D waste recycling facilities in Florida. Screened soil fines were collected from older stockpiles and newly generated piles at the sites. The samples were analyzed for the total concentration (mg/kg) of a series of volatile organic compound (VOCs) and semi-volatile organic compounds (semi-VOCs). The synthetic precipitation leaching procedure (SPLP) test was also performed to evaluate the leachability of the trace organic chemicals. During the total analysis only a few volatile organic compounds were commonly found in the samples (trichlorofluoromethane, toluene, 4-isopropyltoluene, trimethylbenzene, xylenes, and methylene chloride). A total of nine VOCs were detected in the leaching test. Toluene showed the highest leachability among the compounds (61.3-92.0%), while trichlorofluoromethane, the most commonly detected compound from both the total and leaching tests, resulted in the lowest leachability (1.4-39.9%). For the semi-VOC analysis, three base-neutral semi-VOC compounds (bis(2-ethylhexyl)phthalate, butyl benzyl phthalate, and di-n-butyl phthalate) and several PAHs (acenaphthene, pyrene, fluoranthene, and phenanthrene) were commonly detected in C&D fines samples. These compounds also leached during the SPLP leaching test (0.1-25%). No acid extractable compounds, pesticides, or PCBs were detected. The results of this study were further investigated to assess risk from land applied recovered soil fines by comparing total and leaching concentrations of recovered soil fines samples to risk-based standards. The results of this indicate that the organic chemicals in recovered soil fines from C&D debris recycling facilities were not of a major concern in terms of human risk and leaching risk to groundwater under reuse and contact scenarios.     

Managing bioremediation of a creosote‐contaminated superfund site by optimizing moisture and temperature in a biopile

Soil moisture content and temperature in a contaminated soil biopile equipped with immobilized microbe bioreactors (IMBRs) were optimized during ex situ bioremediation at a creosote‐contaminated Superfund site. Efficiency of remediation during warm summer months without soil‐temperature and moisture optimization was compared with that of cold winter months when corrective measures were applied. Significant reduction (35 percent) in total polycyclic aromatic hydrocarbons (PAHs) was observed, compared to 3.97 percent without corrective measures (p < 0.05). Kinetic rates (KRs) for total PAH removal were significantly enhanced from 3.93 to 50.95 mg/kg/day. KRs for removal of high molecular mass four‐to‐six‐ring PAHs were also significantly enhanced from 70.29 mg/kg/day to 97.45 mg/kg/day ( p < 0.05). Bioremediation of two‐ and three‐ring PAHs increased significantly from 15 percent to 40 percent. Benzo[a]pyrene toxicity equivalent mass (BaP_equiv) was significantly reduced by 48 percent with KR of 0.47 mg/kg/day as compared to 22 percent with KR of 0.14 mg/kg/day (p < 0.05). Soil moisture content was enhanced from 15.7 percent to 41.4 percent. © 2007 Wiley Periodicals, Inc.     

Thermal desorption of PCB-contaminated waste at the waukegan harbor superfund site

In June 1992, SoilTech ATP Systems, Inc., completed the soil treatment phase of the Waukegan Harbor Superfund Project in Waukegan, Illinois, after approximately five months of operation. SoilTech successfully treated 12,700 tons of sediment contaminated with polychlorinated hiphenyls (PCBs) using a transportable SoilTech anaerobic thermal processor (ATP) system nominally rated at ten tons per hour throughput capacity. The SoilTech ATP technology anaerobically desorbs contaminants such as PCBs from solids and sludges at temperatures over 1,000° F. Principal products of the process are clean, treated solids and an oil condensate containing the hydrocarbon contaminants. At the Waukegan Harbor Superfund site, PCB concentrations in the sediments excavated and dredged from a ditch, lagoon, and harbor slip averaged 10,400 parts per million (ppm) (1.04 percent) and were as high as 23,000 ppm (2.3 percent). Treated soil was backfilled in an on-site containment cell. The removal efficiency of PCBs from the soil averaged 99.98 percent, relative to the project performance specification of 97 percent, and treated soil PCB concentrations were measured below 2 ppm. Approximately 30,000 gallons of PCB oil, desorbed from the feed material, were returned to the owner for subsequent off-site disposal. After modifications to the emissions control equipment, compliance with the 99.9999 percent destruction and removal efficiency (DRE) for PCBs in stack emissions required by the U.S. Environmental Protection Agency was achieved.     

Impact of iron concentration and ph on zero‐valent iron dechlorination of DDT for brownfields

Soil contamination with persistent pesticides such as dichloro‐diphenyl‐trichloroethane (DDT) is a major issue at many brownfield sites. A technology that can be used to treat DDT‐contaminated soil using surfactants is to enhance the migration of the contaminants from the soil phase to the liquid phase, followed by the dechlorinating of the mobilized DDT in the liquid phase using zero‐valent iron (ZVI). The DDT degradation using ZVI occurs under anaerobic conditions via reductive reactions. The effect of the iron concentration on the dechlorination rate is assessed in the range of 1 to 40 percent (weight to volume) for remediation of a DDT‐contaminated site in Ontario, Canada. The optimum percentage of iron is found to be 20 percent at which the dechlorination rates of DDT and 1,1‐dichloro‐2,2‐bis(p‐chlorophenyl)ethane (DDD) were 4.5 and 0.6 mg/L/day, respectively. While mixing of the reaction solution is shown to be important in providing the iron surface available for the dechlorination reaction throughout the reaction solution, there is no significant difference between batch and fed‐batch mode of adding iron to the dechlorination process. Low pH values (pH = 3) increased the dechlorination rates of DDT and DDD to 6.03 and 0.75 mg/L/day, respectively at a 20 percent iron concentration, indicating increased dechlorination rates in acidic conditions. © 2010 Wiley Periodicals, Inc.     

Phytoremediation of lead-contaminated soil at a New Jersey Brownfield site

Phytoremediation is a new technology that uses specially selected metal-accumulating plants as an attractive and economical method to clean up soils contaminated with heavy metals and radionuclides. The integration of specially selected metal-accumulating crop plants (Brassica juncea (L) Czern.) with innovative soil amendments allows plants to achieve high biomass and metal accumulation rates. In a recent study conducted at a lead-contaminated site in Trenton, New Jersey, the soil was treated with phytoremediation using successive crops of B. juncea combined with soil amendments. Through phytoremediation, the average surface soil lead concentration was reduced by 13 percent. In addition, the target soil concentration of 400 mg/kg was achieved in approximately 72 percent of the treated area in one cropping season.     

Thiourea leaching gold and silver from the printed circuit boards of waste mobile phones

The present communication deals with the leaching of gold and silver from the printed circuit boards (PCBs) of waste mobile phones using an effective and less hazardous system, i.e., a thiourea leaching process as an alternative to the conventional and toxic cyanide leaching of gold. The influence of particle size, thiourea and Fe(3+) concentrations and temperature on the leaching of gold and silver from waste mobile phones was investigated. Gold extraction was found to be enhanced in a PCBs particle size of 100 mesh with the solutions containing 24 g/L thiourea and Fe(3+) concentration of 0.6% under the room temperature. In this case, about 90% of gold and 50% of silver were leached by the reaction of 2h. The obtained data will be useful for the development of processes for the recycling of gold and silver from the PCBs of waste mobile phones.     

Characterization of metal concentration,heavy metal elution,and desalination behavior of municipal solid waste incineration bottom and grate sifting deposition ash based on particle size

Resource and environmental safety protocols of incineration residues were evaluated by analyzing the metal concentration, heavy metal elution, desalination behavior, and chlorine removal ratio owing to particle size differences between bottom ash (BA) and grate sifting deposition ash (GA). In the total content test, Cl, Zn, and Cr in the incinerator BA exceeded the cement acceptance standard (Cl: 1000 mg/kg; Zn: 1700 mg/kg, and Cr: 170 mg/kg) at almost all of the particle sizes, while Au, Ag, Pd, and Zn had high contents in the GA. When using BA as a construction material, heavy metal elution values and contents are restricted as per the product quality standards based on the Japanese soil pollution control law. Lead within the BA and GA exceeded the standard values for most particle sizes. We predicted that there would be a limit on the elution of K by only washing with water. The removal ratio of total chlorine by particle size was approximately 20–70%, where the effect of the particle size on the removal ratio was small, suggesting that the elution of chlorine was complete in approximately 6 hours. These results contribute to information on the recycling of BA and GA.

     

Remediation of persistent organic pollutants (POPs) in two different soils

Persistent organic pollutants (POPs) are a set of chemicals that are toxic, persist in the environment for long periods of time, and biomagnify as they move up through the food chain. The most widely used method of POP destruction is incineration, which is expensive and could result in undesirable by‐products. An alternative bioremediation technology, which is cheaper and environ‐mentally friendly, was tested during this experiment. Two different soil types containing high and low organic matter (OM) were spiked with 100 mg/kg each of pyrene and Aroclor 1248 and planted with three different species of grasses. The objective of the study was to determine residue recovery levels (availability) and potential effectiveness of these plant species for the remediation of POPs. The results showed that recovery levels were highly dependent on the soil organic matter content—very low in all treatments with the high OM content soil compared to recoveries in the low OM soil. This indicates that availability, and, hence, biodegradability of the contaminants is dependent on the organic matter content of the soil. Moreover, the degree of availability was also significantly different for the two classes of chemicals. The polyaromatic hydrocarbon (PAH) recovery (availability) was extremely low in the high organic matter content soil compared to that of the polychlorinated biphenyls (PCBs). In both soil types, all of the plant species treatments showed significantly greater PCB biodegradation compared to the unplanted controls. Planting did not have any significant effect on the transformation of the PAHs in both soil types; however, planting with switchgrass was the best remedial option for both soil types contaminated with PCB. © 2005 Wiley Periodicals, Inc.