Chemical oxidative degradation of methyl tert-butyl ether in aqueous solution by Fenton's reagent

Degradation of methyl tert-butyl ether (MTBE) in aqueous solution by Fenton's reagent (Fe2+ and H2O2) was investigated. Effects of reaction conditions on the oxidation efficiency of MTBE by Fenton's reagent were examined in batch experiments. Under optimum conditions, 15 mM H2O2, 2 mM Fe2+, pH 2.8 and room temperature, the initial 1 mM MTBE solution was reduced by 99% within 120 min. Results showed that MTBE was decomposed in a two-stage reaction. MTBE was first decomposed swiftly based on a Fe2+/H2O2 reaction and then decomposed somewhat less rapidly based on a Fe3+/H2O2 reaction. The detection of Fe2+ also supported the theory of the two-stage reaction for the oxidation of MTBE by Fenton's reagent. The dissolved oxygen in the solution decreased rapidly in the first stage reaction, but it showed a slow increase in the second stage with a zero-order kinetics. A reaction mechanism involving two different pathways for the decomposition of MTBE by Fenton's reagent was also proposed. Chemicals including tert-butyl formate, tert-butyl alcohol, methyl acetate and acetone were identified to be the primary intermediates and by-products of the degradation processes.     

Experimental in situ chemical peroxidation of atrazine in contaminated soil

Lab-scale experiments of in situ chemical oxidation (ISCO), were performed on soil contaminated with 100 mg kg(-1) of atrazine (CIET). The oxidant used was hydrogen peroxide catalysed by naturally occurring minerals or by soluble Fe(II) sulphate, added in aqueous solution. The oxidation conditions were: CIET:H2O2=1:1100, 2 PV or 3 PV reaction volume, Fe(II):H2O2=0, 1:22, 1:11. Stabilized (with KH2PO4 at a concentration of 16 g l(-1)) or non-stabilized hydrogen peroxide was used. The pH of the reagents was adjusted to pH=1 with sulphuric acid, or was not altered. Results showed that the addition of soluble Fe(II) increased the temperature of the soil slurry and the use of stabilized hydrogen peroxide resulted in a lower heat generation. The treatment reduced the COD of the soil of about 40%, pH was lowered and natural organic matter became less hydrophobic. The highest atrazine conversion (89%) was obtained in the conditions: 3 PV, Fe(II):H2O2=1:11 with stabilized hydrogen peroxide added in two steps. The stabilizer only increased H2O2 life-time significantly when soluble Fe(II) was added. Results indicate as preferential degradation pathway of atrazine in soil dechlorination instead of dealkylation.     

Fe (III) supported on resin as effective catalyst for the heterogeneous oxidation of phenol in aqueous solution

FeIII supported on resin as an effective catalyst for oxidation was prepared and applied for the degradation of aqueous phenol. Phenol was selected as a model pollutant and the catalytic oxidation was carried out in a batch reactor using hydrogen peroxide as the oxidant. The influent factors on oxidation, such as catalyst dosage, H2O2 concentration, pH, and phenol concentration were examined by considering both phenol conversion and chemical oxygen demand (COD) removal. The FeIII-resin catalyst possesses a high oxidation activity for phenol degradation in aqueous solution. The experimental results of this study show that almost 100% phenol conversion and over 80% COD removal can be achieved with the FeIII-resin catalyst catalytic oxidation system. A series of prepared resin were investigated for improving the oxidation efficiency. It was found that the reaction temperature and initial pH in solution significantly affected both of phenol conversion and COD removal efficiency. The activity of the catalyst significantly decreased at high pH, which was similar to the Fenton-like reaction mechanism. Results in this study indicate that the FeIII-resin catalytic oxidation process is an efficient method for the treatment of phenolic wastewater.     

Activation of H2O2 by Amberlyst-15 resin supported with copper(II)-complexes towards oxidation of crystal violet

Copper(II) amine complexes supported on Amberlyst-15 cation resin were prepared and characterized by SEM, EDX and FTIR measurements. The kinetics of the heterogeneous oxidation of an organic dye, crystal violet, with H2O2 catalyzed by the supported catalysts was investigated in aqueous solution. The rate of reaction increases with increasing stability of the copper(II) amine complexes. The oxidation rate attained a first-order in the catalyst and the dye only at lower concentrations and second order in H2O2. A very fast formation of a peroxo-dye intermediate resulting from the interaction of H2O2 with the dye even in the presence of the catalyst was observed.     

Kinetics of oxidation of chlorobenzenes and phenyl-ureas by Fe(II)/H2O2 and Fe(III)/H2O2. Evidence of reduction and oxidation reactions of intermediates by Fe(II) or Fe(III)

The rates of degradation of 1,2,4-trichlorobenzene (TCB), 2,5-dichloronitrobenzene (DCNB), diuron and isoproturon by Fe(II)/H2O2 and Fe(III)/H2O2 have been investigated in dilute aqueous solution ([Organic compound]0 approximately 1 microM, at 25.0 +/- 0.2 degrees C and pH < or = 3). Using the relative rate method with atrazine as the reference compound, and the Fe(II)/H2O2 (with an excess of Fe(II)) and Fe(III)/H2O2 systems as sources of OH radicals, the rate constants for the reaction of OH* with TCB and DCNB were determined as (6.0 +/- 0.3)10(9) and (1.1 +/- 0.2)10(9) M(-1) s(-1). Relative rates of degradation of diuron and isoproturon by Fe(II)/H2O2 were about two times smaller in the absence of dissolved oxygen than in the presence of oxygen. These data indicate that radical intermediates are reduced back to the parent compound by Fe(II) in the absence of oxygen. Oxidation experiments with Fe(III)/H2O2 showed that the rate of decomposition of atrazine markedly increased in the presence of TCB and this increase has been attributed to a regeneration of Fe(II) by oxidation reactions of intermediates (radical species and dihydroxybenzenes) by Fe(III).     

Oxidation of chlorophenols in soil at natural pH by catalyzed hydrogen peroxide: the effect of soil organic matter.

This investigation reports on the effects of soil organic matter (SOM) during the oxidation of chlorophenols with Fe2+-catalyzed H2O2 (Fenton oxidation) system. The soil pH was 7.1 and was not altered. Sorption experiments of soil pre-treated under various oxidation conditions were performed. Concentrations of organic matter in the liquid phase and soil before and after oxidation were analyzed. The results were correlated to the observation in batch Fenton oxidation tests. They showed that the oxidation of chlorophenols at natural soil pH depended on the dose of H2O2 and Fe2+. The soil organic content did not vary significantly after various Fenton treatments, while the sorption of chlorophenols was 10-25% less by the oxidation. The concentration of chlorophenols in the liquid phase exhibited a "decrease and rebound" phenomenon in the batch Fenton oxidation tests. It appeared that the oxidation of SOM resulted in the release of sorbed chlorophenols which were then oxidized by the excess H2O2. An "oxidation-desorption-oxidation" scheme was proposed to describe one of the interaction mechanisms among the oxidant, SOM, and chlorophenols during oxidation.     

A kinetic study on oxidation of pentachlorophenol by ozone

The kinetics of pentachlorophenol (PCP) ozonation in terms of the gaseous O3 and dissolved PCP concentrations has been investigated. When the O3 concentration in the gas phase was in the range of 10 to 40 g O3/m3, the O3 dissolved for a short time period was proportional to the gaseous O3 concentration. In this range, the ozonation reaction was first order for each reactant and the overall reaction was second order. At 25 degrees C, in an aqueous solution, the reaction rate constant was estimated to be 10.048 L/mol.sec. The reaction rate was much greater than the mass-transfer rate, indicating that the reaction of O3 and PCP was an interface reaction on the surface of gaseous O3 bubbles. The final product of the PCP ozonation was oxalic acid, with the carbon yield of the reaction being 59.4%. The ozonation of PCP in the aqueous solution was not a radical reaction but a direct reaction between O3 and PCP molecules under the conditions investigated in this study, since O3 has a high selectivity toward PCP. The reaction rate increased with the reaction temperature up to 35 degrees C but decreased at temperatures greater than 35 degrees C due to the decreased solubility of O3. The addition of H2O2 did not increase the reaction rate significantly.     

Persulfate oxidation for in situ remediation of TCE. II. Activated by chelated ferrous ion

In situ chemical oxidation (ISCO) is a technique used to remediate contaminated soil and groundwater systems. It has been postulated that sodium persulfate (Na2S2O8) can be activated by transition metal ions such as ferrous ion (Fe2+) to produce a powerful oxidant known as the sulfate free radical (SO4-*) with a redox potential of 2.6 V, which can potentially destroy organic contaminants. In this laboratory study persulfate oxidation of dissolved trichloroethylene (TCE) was investigated in aqueous and soil slurry systems under a variety of experimental conditions. A chelating agent (i.e., citric acid) was used in attempt to manipulate the quantity of ferrous ion in solution by providing an appropriate chelate/Fe2+ molar ratio. In an aqueous system a chelate/Fe2+ molar ratio of 1/5 (e.g., S2O8(2)-/chelate/Fe2+/TCE ratio of 20/2/10/1) was found to be the lowest acceptable ratio to maintain sufficient quantities of Fe2+ activator in solution resulting in nearly complete TCE destruction after only 20 min. The availability of Fe2+ appeared to be controlled by adjusting the molar ratio of chelate/Fe2+. In general, high levels of chelated ferrous ion concentrations resulted in faster TCE degradation and more persulfate decomposition. However, if initial ferrous ion contents are relatively low, sufficient quantities of chelate must be provided to ensure the chelation of a greater percentage of the limited ferrous ion present. Citric acid chelated ferrous ion appeared effective for TCE degradation within soil slurries but required longer reaction times. Additionally, the use of citric acid without the addition of supplemental Fe2+ in soil slurries, where the citric acid apparently extracted native metals from the soil, appeared to be somewhat effective at enhancing persulfate oxidation of TCE over extended reaction times. A comparison of different chelating agents revealed that citric acid was the most effective.     

活性炭负载Fe^3＋催化H2O2氧化邻苯二甲酸二甲酯

将Fe3＋负载在活性炭上制得载铁催化剂Fe/AC,并研究了该催化剂对邻苯二甲酸二甲酯（DMP）的催化降解性能。通过正交实验和单因素实验,探讨了催化剂投加量、H2O2投加量、溶液pH值和反应温度对水中DMP降解率的影响,同时对DMP矿化度进行了分析。实验结果表明,制得的载铁催化剂具有较高的催化活性;降解效果的影响顺序是反应温度〉催化剂投加量〉H2O2投加量〉溶液pH值;在反应温度为80℃、催化剂投加量为4 g/L、H2O2投加量为20 mL/L和溶液pH值为3的条件下反应120 min后,质量浓度为10 mg/L的DMP降解率最高可达97.73%;在优化的实验条件下反应150 min,DMP矿化度可达62.73%;催化剂反复使用5次仍具有较好的催化活性,DMP降解率仍可达到77%以上;反应过程中溶液Fe3＋浓度的变化维持在1.07 mg/L左右,且可推测催化降解DMP主要是由非均相和均相催化氧化反应共同作用的。     

Comparison of the degradation of p-hydroxybenzoic acid in aqueous solution by several oxidation processes

A comparative study is made of 12 methods of chemical oxidation applied to degrading p-hydroxybenzoic acid in aqueous solution. The oxidation processes tested were: UV, O3, UV/TiO2, O3/Fe2+, O3/H2O2, O3/UV, UV/H2O2, H2O2/Fe2+, H2O2/Fe2+/O3, UV/H2O2/O3, H2O2/Fe2+/UV and O3/UV/H2O2/Fe2+. The 12 processes were ranked by reactivity. In a kinetic study, the overall kinetic rate constant was split up into three components: direct oxidation by UV irradiation (photolysis), direct oxidation by ozone (ozonation), and oxidation by free radicals (mainly OH*).     

低频超声协同Fe-Ni-Mn/Al_2O_3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn/Al2O3催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H2O2等因素对酸性绿B降解效果的影响,结果表明:催化剂Fe-Ni-Mn/Al2O3与低频超声存在协同效应,催化剂的最佳投加量为6 g/L;酸性条件有利于染料的超声降解,当pH=3.8时,可取得最佳的降解效果;酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100 mg/L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体(air+Ar)>氧气>氩气;在反应过程中投加H2O2有利于染料降解率的提高.在优化实验条件下降解150 min,酸性绿B色度去除率达到91.4%.     

Aniline degradation by Electro-Fenton and peroxi-coagulation processes using a flow reactor for wastewater treatment

The degradation of 10-30 l of a 1000 ppm aniline solution in 0.050 M Na2SO4 + H2SO4 at pH 3.0 and 40 degrees C by Electro-Fenton and peroxi-coagulation processes at constant current until 20 A has been studied using a pilot flow reactor in recirculation mode with a filter-press cell containing an anode and an oxygen diffusion cathode, both of 100 cm2 area. H2O2 is produced by the two-electron reduction of O2 at the cathode, being accumulated with a current efficiency between 60% and 80% at the first stages of electrolyses performed with a Ti/Pt anode. In the presence of 1 mM Fe2+, less H2O2 is accumulated, but it is not detected using an Fe anode. The Electro-Fenton process with 1 mM Fe2+ and a Ti/Pt or DSA anode yields an insoluble violet polymer, while the soluble total organic carbon (TOC) is gradually removed, reaching 61% degradation after 2 h at 20 A. In this treatment, pollutants are preferentially oxidized by hydroxyl radicals formed in solution from reaction of Fe2+ with H2O2. The peroxi-coagulation process with an Fe anode has higher degradation power, allowing to remove more than 95% of pollutants at 20 A, since some intermediates coagulate with the Fe(OH)3 precipitate formed. Both advanced electrochemical oxidation processes (AEOPs) show moderate energy costs, which increase with increasing electrolysis time and applied current.     

Enhanced chemical oxidation of aromatic hydrocarbons in soil systems

Fenton's destruction of benzene, toluene, ethylbenzene, and xylene (BTEX) was investigated in soil slurry batch reactors. The purpose of the investigation was to quantify the enhancement of oxidation rates and efficiency by varying process conditions such as iron catalyst (Fe(II) or Fe(III); 2, 5, and 10mM), hydrogen peroxide (H2O2; 30, 150, 300 mM), and metal chelating agents (l-ascorbic acid, gallic acid, or N-(2-hydroxyethyl)iminodiacetic acid). Rapid contaminant mass destruction (97% after 3h) occurred in the presence of 300 mM H2O2 and 10 mM Fe(III). An enhanced removal rate (>90% removal after 15 min and 95% removal after 3h) was also observed by combining Fe(III), N-(2-hydroxyethyl)iminodiacetic acid and 300 mM H2O2. The observed BTEX mass removal rate constants (3.6-7.8 x 10(-4)s(-1)) were compared to the estimated rate constants (4.1-10.1 x 10(-3)s(-1)). The influence of non-specific oxidants loss (by reaction with iron hydroxides and soil organic matter) was also explored.     

Factors influencing the preparation of supported iron oxide in fluidized-bed crystallization

Our previous work applied a novel supported iron oxyhydroxide (FeOOH) catalyst to effectively treat benzoic acid by hydrogen peroxide. The FeOOH catalyst was prepared via the oxidation of Fe2+ by H2O2 in the acidic condition using a fluidized-bed crystallization reactor. The major components coated on the surface were identified as amorphous FeOOH and gamma-FeOOH. In terms of the crystallization conditions of FeOOH, some parameters including the operational pH, superficial velocity, specific iron loading, and influent H2O2 concentration were investigated to quantify their effects on the crystallization efficiency. All these parameters were found to significantly influence the crystallization efficiency. Two types of FeOOH catalysts were synthesized: FeOOH I was prepared at pH 3.5, and FeOOH II was formed by aging FeOOH I at pH 13. The percentages of surface amorphous FeOOH reduced from 70% to 30% after aging. The FeOOH II catalyst presented a higher reactivity toward H2O2 but lower stoichiometric efficiency in oxidizing benzoic acid than FeOOH I, similar to the result of the commercial goethite. Therefore, it is concluded that the crystalline property significantly affects the performance of catalytic oxidation.     

低频超声协同Fe-Ni-Mn／Al2O3催化降解酸性绿B的研究

采用低频超声与Fe-Ni-Mn／Al2O3催化剂协同降解偶氮染料酸性绿B模拟废水,考察染料初始浓度和pH值、催化剂、饱和气体及H2O2等因素对酸性绿B降解效果的影响,结果表明：催化剂Fe-Ni-Mn／Al2O3与低频超声存在协同效应,催化剂的最佳投加量为6g／L;酸性条件有利于染料的超声降解,当pH=3．8时,可取得最佳的降解效果;酸性绿B降解率随初始浓度的增大而降低,其优化初始浓度为100mg／L,此外,在反应体系中鼓入饱和气体也可促进酸性B的降解,且影响顺序为混合气体（air＋Ar）〉氧气〉氩气;在反应过程中投加H2O2有利于染料降解率的提高。在优化实验条件下降解150min,酸性绿B色度去除率达到91．4％。     

超声波/紫外线-Fenton反应联用去除克拉玛依土壤中石油类污染物

研究了超声波(ultrasonic)和紫外线(ultraviolet)-Fenton反应联用处理干旱区老化石油污染土壤。土壤TPH含量为30 470 mg/kg,pH值为3,H2O2与Fe比例为50∶1时,H2O2浓度为0.37%、0.74%、1.11%和1.85%在超声波处理6 h土壤TPH去除量分别为4 495、11 983、15 470和19 800 mg/kg;TPH去除量随H2O2/Fe2+增大而增大,H2O2/Fe2+为100∶1时,TPH去除量为12 699 mg/kg。溶液pH值接近中性,H2O2浓度为0.74%,H2O2/Fe2+为50∶1,超声波与UV共同作用2 h和4 h,TPH去除量分别达到14 824和21 821 mg/kg;UV单独作用2 h、4 h对土壤TPH去除量为9 253和12 845 mg/kg。超声波-Fenton反应对1,2-二甲苯降解效果最好,其次为C17-C28的直链及支链烷烃,最低为烃类衍生物。     

Decolorization and degradation of H-acid and other dyes using ferrous-hydrogen peroxide system

In this study, advanced oxidation process utilizing Fenton's reaction was investigated for the decolorization and degradation of two commercial dyes viz., Red M5B, Blue MR and H-acid, a dye intermediate used in chemical industries for the synthesis of direct, reactive and azo dyes. Effect of Fe2 +, H2O2, pH, and contact time on the degradation of the dyes was studied. Maximum color and COD removal was obtained for Red MSB, H-acid and Blue MR at 10-25 mg/l of Fe2+ dose and 400-500 mg/l of H2O2 dose at pH 3.0. The initial oxidation reaction was found to fit into first order rate kinetics and the rate of oxidation of H-acid was higher than the other dyes. Release of chloride and sulfate from the Fenton's treated Red M5B dye and sulfate from H-acid and Blue MR indicates that the dye degradation proceeds through cleavage of the substituent group.     

Cu-SBA-15催化湿式过氧化氢氧化水溶液中罗丹明B

采用水热晶化法合成了不同含铜量的Cu—SBA-15介孔分子筛,并且用XRD、N2吸附、TEM以及uV—vis对所合成的样品进行表征。以Cu—SBA-15为催化剂,H2O2为氧化剂,催化湿式过氧化水溶液中的罗丹明B,主要考察H2O2浓度、催化剂用量、处理温度、初始pH等因素对罗丹明B氧化效果的影响。结果表明,在同样的处理条件下罗丹明的脱色率明显高于TOC去除率,处理温度、初始pH对罗丹明B的脱色与氧化有重要影响。在罗丹明B初始浓度100mg／L,H2O2初始浓度1．8g／L,催化剂量0．3g／L,温度60℃,pH为7．0,处理时间100min时,罗丹明B的脱色率为98．6％,TOC去除率为62．8％。     

Citric acid-modified Fenton's reaction for the oxidation of chlorinated ethylenes in soil solution systems

Fenton's reagent, a solution of hydrogen peroxide and ferrous iron catalyst, is used for an in situ chemical oxidation of organic contaminants. Sulfuric acid is commonly used to create an acidic condition needed for catalytic oxidation. Fenton's reaction often involves pressure buildup and precipitation of reaction products, which can cause safety hazards and diminish efficiency. We selected citric acid, a food-grade substance, as an acidifying agent to evaluate its efficiencies for organic contaminant removal in Fenton's reaction, and examined the impacts of using citric acid on the unwanted reaction products. A series of batch and column experiments were performed with varying H2O2 concentrations to decompose selected chlorinated ethylenes. Either dissolved iron from soil or iron sulfate salt was added to provide the iron catalyst in the batch tests. Batch experiments revealed that both citric and sulfuric acid systems achieved over 90% contaminant removal rates, and the presence of iron catalyst was essential for effective decontamination. Batch tests with citric acid showed no signs of pressure accumulation and solid precipitations, however the results suggested that an excessive usage of H2O2 relative to iron catalysts (Fe2+/H2O2<1/330) would result in lowering the efficiency of contaminant removal by iron chelation in the citric acid system. Column tests confirmed that citric acid could provide suitable acidic conditions to achieve higher than 55% contaminant removal rates.     

双氧水催化氧化中Cu/γ-Al_2O_3催化剂的稳定性研究

针对废水湿式双氧水催化氧化,采用浸渍法制备Cu催化剂,研究非均相Cu催化剂在常温常压湿式双氧水催化氧化中的稳定性与失活问题。研究表明,催化剂制备条件及催化氧化反应条件对催化剂中Cu2＋溶出均有影响。研究同时表明,催化剂失活与活性组分流失和活性组分被有机中间产物覆盖有关,高温焙烧可对催化剂再生。