Successful unsaturated zone treatment of PCE with sodium permanganate

In situ chemical oxidation (ISCO) with permanganate has been widely used for soil and groundwater treatment in the saturated zone. Due to the challenges associated with achieving effective distribution and retention in the unsaturated zone, there is a great interest in developing alternative injection technologies that increase the success of vadose‐zone treatment. The subject site is an active dry cleaner located in Topeka, Kansas. A relatively small area of residual contamination adjacent to the active facility building has been identified as the source of a large sitewide groundwater contamination plume with off‐site receptors. The Kansas Department of Health and Environment (KDHE) currently manages site remedial efforts and chose to pilot‐test ISCO with permanganate for the reduction of perchloroethene (PCE) soil concentrations within the source area. KDHE subsequently contracted Burns & McDonnell to design and implement an ISCO pilot test. A treatability study was performed by Carus Corporation to determine permanganate‐soil‐oxidant‐demand (PSOD) and the required oxidant dosing for the site. The pilot‐test design included an ISCO injection approach that consisted of injecting aqueous sodium permanganate using direct‐push technology with a sealed borehole. During the pilot test, approximately 12,500 pounds of sodium permanganate were injected at a concentration of approximately 3 percent (by weight) using the methods described above. Confirmation soil sampling conducted after the injection event indicated PCE reductions ranging from approximately 79 to more than 99 percent. A follow‐up treatment, consisting of the injection of an additional 6,200 pounds of sodium permanganate, was implemented to address residual soil impacts remaining in the soil source zone. Confirmation soil sampling conducted after the treatment indicated a PCE reduction of greater than 90 percent at the most heavily impacted sample location and additional reductions in four of the six samples collected. © 2009 Wiley Periodicals, Inc.     

Bioventing of No. 2 Fuel Oil: Effects of Air Flowrate,Temperature, Nutrient Amendment,and Acclimation

A 14‐month pilot‐scale bioventing study, sponsored by the New Hampshire Department of Environmental Services, was conducted by the University of New Hampshire to determine the effects of the time between the contamination event and the onset of bioventing, as well as air flowrate, temperature, and nutrient amendments. Freshly contaminated soil was not readily amenable to bioventing. Bioventing was effective (82–92.5 percent removal) for acclimated soil amended with nutrients at 10 °C and 20 °C for the 275 cm³/min and 140 cm³/min air flowrates, respectively. First order degradation rates after nutrient addition were ?6.11 ± 0.83 (×10^?3)/day and ?6.57 ± 1.71 (×10^?3)/day, respectively. The results indicate that bioventing will be best applied when the contamination has occurred at least two years before the onset of treatment. © 2014 Wiley Periodicals, Inc.     

Low‐concentration hydrogen peroxide decontamination for Bacillus spore contamination in buildings

Remediation and recovery efforts after a release of Bacillus anthracis (anthrax) spores may be difficult and costly. In addition, response and recovery technologies may be focused on critical resources, leaving the small business or homeowner without remediation options. This study evaluates the efficacy of relatively low levels of hydrogen peroxide vapor (HPV) delivered from off‐the‐shelf equipment for the inactivation of Bacillus spores within an indoor environment. Decontamination evaluations were conducted in a house using both Bacillus atrophaeus var. globigii (Bg; as surrogates for B. anthracis) inoculated on the carpet and galvanized metal as coupons and Geobacillus stearothermophilus (Gs) as biological indicators on steel. The total decontamination time ranged from 4 to 7 days. Using the longer exposure times, low concentrations of HPV (average levels below 20 parts per million) effectively inactivated Bg and Gs spores on the materials tested. The HPV was generated with commercial humidifiers and household‐strength hydrogen peroxide solutions. The presence of home furnishings did not have a significant impact on HPV efficacy. This simple, inexpensive, and effective decontamination method could have significant utility for remediation following a B. anthracis spore release, such as following a terrorist attack.     

Results of a field study—Sampling with ISOCS and SAM 935 at the Savannah River Site

This article focuses on the results of a delineation of radioactive contaminants using expedited field characterization equipment at the Department of Energy's Savannah River Site in South Carolina. The objective of the study was to delineate a potential contamination area in the TNX Inner Swamp using cost‐effective field sampling equipment that would give results in a timely manner. The expedited field characterization equipment used was the In Situ Object Counting System (ISOCS) and the Model 935 Surveillance and Measurement System (SAM 935). The study involved an area of approximately 200 acres with 89 surveyed locations. Originally, the contaminant of concern was thorium‐232 because of the health risk to future on‐site workers. As the fieldwork progressed, there were no exceedances in thorium‐232 activities; however, there was one slight exceedance of uranium‐238. The delineation was established from using the ISOCS and SAM 935 sampling equipment in addition to soil sampling from the 0‐ to 1‐foot interval. There was a strong correlation in the analytical data from both the ISOCS and SAM 935 measurements. Thus, this type of sampling characterization is beneficial for determining the extent of contamination at hazardous waste sites. © 2006 Wiley Periodicals, Inc.     

An In Situ Bioreactor for the Treatment of Petroleum Hydrocarbons in Groundwater

Two pilot tests of an aerobic in situ bioreactor (ISBR) have been conducted at field sites contaminated with petroleum hydrocarbons. The two sites differed with respect to hydrocarbon concentrations. At one site, concentrations were low but persistent, and at the other site concentrations were high enough to be inhibitory to biodegradation. The ISBR unit is designed to enhance biodegradation of hydrocarbons by stimulating indigenous microorganisms. This approach builds on existing Bio‐Sep^® bead technology, which provides a matrix that can be rapidly colonized by the active members of the microbial community and serves to concentrate indigenous degraders. Oxygen and nutrients are delivered to the bioreactor to maintain conditions favorable for growth and reproduction, and contaminated groundwater is treated as it is circulated through the bed of Bio‐Sep^® beads. Groundwater moving through the system also transports degraders released from Bio‐Sep^® beads away from the bioreactor, potentially increasing biodegradation rates throughout the aquifer. Groundwater sampling, Bio‐Traps, and molecular biological tools were used to assess ISBR performance during the two pilot tests. Groundwater monitoring indicated that contaminant concentrations decreased at both sites, and the microbial data suggested that these decreases were due to degradation by indigenous microorganisms rather than dilution or dispersion mechanisms. Taken together, these lines of evidence showed that the ISBR system effectively increased the number and activity of indigenous microbial degraders and enhanced bioremediation at the test sites. © 2013 Wiley Periodicals, Inc.     

Regional Assessment of Nutrient and Pesticide Leaching in the Vegetable Production Area of Rattaphum Catchment, Thailand

Regional groundwater vulnerability maps to indicate the impact of leaching of chemicals under different management scenarios were prepared for the Rattaphum Catchment using several leaching models and GIS techniques. The Attenuation Factor (AF) model was used to simulate the leaching potential of several pesticides for selected soils in the catchment under different rates of recharge from irrigation. The LEACHN model was used to simulate the NO₃ ⁻ leaching potential and LEACHP was used to simulate leaching potential of metolachlor under different management scenarios. The results showed that only a small number of pesticides have the potential to contaminate the shallow groundwater. However, the risk of contamination with nutrients is much higher due to the mobility and conservative nature of the NO₃ ⁻. The LEACHP results indicated that the intensive use of agrochemicals in the vegetable growing area, especially during the rainy season when the groundwater is near the surface, increases the risk of pesticide contamination. The results of upscaling from the farm to the catchment scale using soil maps and GIS techniques under various management scenarios and chemical application rates showed that the most effective strategy to reduce chemical leaching is by reducing pesticide application rates and optimizing the application of irrigation water. The identification of potential high risk farms by ranking soils and agricultural practices could be used to formulate management practices that reduce pesticide contamination of the surface and ground water resources in the area.     

Destruction of Aspergillus versicolor,Penicillium chrysogenum,Stachybotrys chartarum,and Cladosporium cladosporioides spores using chemical oxidation treatment process

The survival of aqueous suspensions of Penicillium chrysogenum, Stachybotrys chartarum, Aspergillus versicolor, and Cladosporium cladosporioides spores was evaluated using various combinations of hydrogen peroxide and Fe²⁺ as catalyst. Spore concentrations of 10⁶–10⁷ colony forming units per milliliter (CFU/mL) were suspended in water and treated with initial hydrogen peroxide and iron concentrations ranging from 0.05 to 10 percent and 100 to 200 ppm, respectively. After four hours of reaction time, samples were plated on agar plates, and the viable fraction of spores was determined by the number of colonies formed. Hydrogen peroxide concentrations above 50,000 ppm resulted in greater than 6‐log₁₀ reduction of viable spores for both catalyzed and noncatalyzed reactions. Iron had a strong catalytic effect when added to solutions with hydrogen peroxide concentration above 5,000 ppm and resulted in two to three orders of magnitude greater reduction compared to hydrogen peroxide alone. Additional samples taken after 24 hours of reaction time showed that the effect of the addition of 100 and 200 ppm of Fe²⁺ catalyst was mostly kinetic, and noncatalyzed hydrogen peroxide had sporicidal effects similar to catalyzed hydrogen peroxide. This study identified initial reagent concentrations of hydrogen peroxide and Fe²⁺ that accomplish a 6‐log₁₀ reduction of viable mold spores within reaction times of 4 and 24 hours. © 2007 Wiley Periodicals, Inc.     

The Hidden Potential of Mass‐based Treatment: A Method for Preventing Rebound

A major challenge for in situ treatment is rebound. Rebound is the return of contaminant concentrations to near original levels following treatment, and frequently occurs because much of the residual nonaqueous phase liquid (NAPL) trapped within the soil capillaries or rock fractures remains unreachable by conventional in situ treatment. Fine‐textured strata have an especially strong capacity to absorb and retain contaminants. Through matrix diffusion, the contaminants dissolve back into groundwater and return with concentrations that can approach pretreatment levels. The residual NAPL then serves as a continuing source of contamination that may persist for decades or longer. A 0.73‐acre (0.3‐hectare) site in New York City housed a manufacturer of roofing materials for approximately 60 years. Coal tar served as waterproofing material in the manufacturing process and releases left behind residual NAPL in soils. An estimated 47,000 pounds (21,360 kg) of residual coal tar NAPL contaminated soils and groundwater. The soils contained strata composed of sands, silty sands, and silty clay. A single treatment using the RemMetrik^® process and Pressure Pulse Technology^® (PPT) targeted the contaminant mass and delivered alkaline‐activated sodium persulfate to the NAPL at the pore‐scale level via in situ treatment. Posttreatment soil sampling demonstrated contaminant mass reductions over 90 percent. Reductions in posttreatment median groundwater concentrations ranged from 49 percent for toluene to 92 percent for xylenes. Benzene decreased by 87 percent, ethylbenzene by 90 percent, naphthalene by 80 percent, and total BTEX by 91 percent. Mass flux analysis three years following treatment shows sustained reductions in BTEX and naphthalene, and no rebound. ©2015 Wiley Periodicals, Inc.     

Conceptual Site Model Development and Phased Remedy Implementation to Achieve Vapor Screening Goals at a Former Dry Cleaner

Tetrachloroethene (PCE) releases at a former dry cleaner resulted in impacts to soil and shallow groundwater beneath and adjacent to the building. Subsurface impacts led to vapor intrusion with PCE concentrations between 900 and 1,200 micrograms per cubic meter (μg/m³) in indoor air. The migration pathways of impacted soil vapor were evaluated through implementation of a helium tracer test and vapor sampling of an exterior concrete block wall. Results confirmed that the concrete block wall acted as a conduit for vapor intrusion into the building. A combination of remediation efforts focused on mass reduction in the source area as well as mitigation efforts to inhibit vapor migration into the building. Excavation of soils beneath the floor slab and installation of a spray‐applied vapor barrier resulted in PCE concentrations in indoor air decreasing by over 97.9 percent. Operation of an active ventilation system installed under the floor slab and groundwater remediation via injections of nano‐scale zero valent iron (nZVI) further reduced PCE concentrations in indoor air by over 99.8 percent compared to baseline conditions. While significant reductions of PCE concentrations in groundwater were observed within two months after injection, maximum reductions to PCE concentrations in indoor air were not observed for an additional 12 months. © 2014 Wiley Periodicals, Inc.     

Test of the Multi Increment Sampling® Method on 14 Playgrounds

The Capital Region of Denmark tested the Multi Increment Sampling^® (MIS) technology at 14 children's playgrounds in the region to assess whether the method provides representative test results and an improved foundation for risk assessment. The purpose of the investigation was to determine whether the previous uses of the playground areas have led to soil contamination that poses a health risk to its current users (children). The unpaved areas of the playgrounds were divided into decision units based on historical data along with the expected patterns of movement from its users. The samples from each unit consisted of 45 to 100 increments were collected from three depths within the upper one‐half meter. Furthermore, triplicate samples were taken from the upper sampling depth in at least one unit for quality control purposes. The investigation results showed excellent consistency between the pollution parameters and contamination levels in different decision units for each playground. The decision units where high levels of soil contamination exist coincide well with the previous site history. The MIS method has proven to be expensive and time consuming. However, in the future it will be easier to implement as we gain more experience with use of this method.  ©2016 Wiley Periodicals, Inc.     

Chlorinated Hydrocarbon–Contaminated Site Investigation With Optimized 3D‐CSIA Approach

An optimized “Three‐Dimensional Compound Specific Isotope Analysis (3D‐CSIA)'' investigation was conducted at a chlorinated hydrocarbon–contaminated site in order to (1) determine if multiple onsite sources of groundwater contamination existed and (2) demonstrate the cost‐effectiveness of applying isotope fingerprinting at such a complex contaminated site. Previous groundwater investigations identified chlorinated hydrocarbons at levels that significantly exceed drinking‐water standards but failed to determine the source(s) of contamination due to the lack of vadose‐zone contamination and the absence of groundwater contaminants in shallow portions of the surficial aquifer. To better understand the contaminant source(s), groundwater samples were taken and tested for both the presence of chlorinated hydrocarbons and their isotopic signatures of ¹³C/¹²C, ³⁷Cl/³⁵Cl, and ²H/¹H. A site investigation with an optimized 3D‐CSIA approach revealed multiple chlorinated hydrocarbon releases from different sources, which was also cost‐effective considering the new lines of evidence of target contaminants obtained with the 3D‐CSIA approach instead of any traditional fingerprinting approaches. In addition, the 3D‐CSIA results inferred in situ bioremediation of chlorinated hydrocarbons would be feasible at the site. © 2013 Wiley Periodicals, Inc.     

Evaluation of PFAS treatment technology: Alkaline ozonation

A bench‐scale treatability study was performed to evaluate the effectiveness of alkaline ozonation on removing per‐ and polyfluoroalkyl substances (PFAS) present in groundwater at a former industrial site in Michigan. The study involved testing the PFAS‐impacted groundwater under alkaline ozonating conditions under a range of experimental conditions, including modifying pH, hydrogen peroxide‐to‐ozone molar ratio doses, length of ozonation pretreatment times, and sampling techniques. PFAS‐spiked samples were used to determine if inorganic ions such as fluoride (F^?), sulfate (SO₄^2?), formate (HCOO^?), acetate (CH₃COO^?), and trifluoroacetate (CF₃COO^?) were generated or if there were decreases in total organic fluorine resulting from PFAS treatment. The results from all tests indicate that decreases in PFAS concentrations were due to a combination of removal and destructive mechanisms with enhanced removal under acidic pH ozonation pretreatment conditions. Short‐chain PFAS concentrations increased during the experiments followed by an overall decrease in concentration under continuous alkaline ozonation conditions. Reductions in concentrations in perfluorooctane sulfonic acid of 75–97% were observed. Reductions in concentrations were also observed in other PFAS such as 6:2 FTS, PFHxS, PFOA, and PFNA. To our best knowledge, this is the first time that alkaline ozonation has been performed on PFAS‐impacted water while monitoring a larger suite of PFAS analytes in addition to destruction byproducts. Treatment of PFAS under the conditions discussed in this paper suggests that alkaline ozonation may be a viable remediation option for PFAS‐impacted waters.     

Residential vapor‐intrusion evaluation: Long‐duration passive sampling vs. short‐duration active sampling

Sampling indoor air for potential vapor‐intrusion impacts using current standard 24‐hour sample collection methods may not adequately account for temporal variability and detect contamination best represented by long‐term sampling periods. Henry Schuver of the U.S. Environmental Protection Agency Office of Solid Waste stated at the September 2007 Air & Waste Management Association vapor‐intrusion conference that the US EPA may consider recommending longer‐term vapor sampling to achieve more accurate time‐weighted‐average detections. In November 2007, indoor air at four residences was sampled to measure trichloroethene (TCE) concentrations over short‐ and long‐duration intervals. A carefully designed investigation was conducted consisting of triplicate samplers for three different investigatory methods: dedicated 6‐liter Summa canisters (US EPA Method TO‐15), pump/sorbent tubes (US EPA Method TO‐17), and passive diffusion samplers (MDHS 80). The first two methods collected samples simultaneously for a 24‐hour period, and the third method collected samples for two weeks. Data collected using Methods TO‐15 (canisters) and TO‐17 (tubes) provided reliable short‐duration TCE concentrations that agree with prior 24‐hour sampling events in each of the residences; however, the passive diffusion samplers may provide a more representative time‐weighted measurement. The ratio of measured TCE concentrations between the canisters and tubes are consistent with previous results and as much as 28.0 μg/m³ were measured. A comparison of the sampling procedures, and findings of the three methods used in this study will be presented. © 2008 Wiley Periodicals, Inc.     

Remediation of a Diffuse Trichloroethene Plume in an Urban Setting

During an environmental assessment of a former fleet vehicle maintenance facility located in Jacksonville, Florida, dissolved trichloroethene (TCE) concentrations exceeding the Florida groundwater standard (3 micrograms per liter) were detected at a depth of 40 feet (12 meters) below land surface (bls). A plume was delineated that measured approximately 600 feet (183 meters) by 150 feet (46 meters), extending across a major road and onto adjacent properties. Shaw Environmental, Inc., which was acquired by CB&I in February 2012, performed pilot tests with in situ oxygen curtain (iSOC), and the injection of Anaerobic Biochem Plus (ABC+), a mixture of lactates, a phosphate buffer, fatty acids, and zero‐valent iron. Based on the pilot‐test results, ABC+ appeared the more effective of the two methods and was selected for full‐scale implementation. In February 2011, Shaw Environmental, Inc. and a subcontractor used direct‐push technology to inject ABC+ in 120 borings. By September 2011, the treatment succeeded in lowering the concentrations of TCE to below the Florida standard in all impacted wells. Subsequent sampling events indicate that TCE concentrations have remained below the standard, but sampling continues for iron, which is decreasing but remains slightly elevated. © 2013 Wiley Periodicals, Inc.     

Field Evidence of Dissolution and Degradation Rates Enhancement During ISCR and ENA Treatments of Chlorinated Solvents

This article presents field tests comparing two methods of treatment of chlorinated solvents undertaken at the same site. The site is an automobile factory where two chlorinated solvents (CS) plumes were identified. At the first source, in situ chemical reduction (ISCR) was applied, while at the second one, enhanced natural attenuation (ENA) was used. A set of specific multilevel sampling wells were installed approximately 20 m downgradient of the sources to estimate the efficiency of the treatments. The presence of a low‐permeability layer (source 1) or a thick oil lens (source 2) in the top part of the aquifer prevented the CS from reaching the bottom of the aquifer. These layers led to difficulties treating the contamination. At the ISCR and ENA treatment zones, the concentrations of tetrachloroethene (PCE) and trichloroethene (TCE) did not change significantly, while the concentration of metabolites (cis‐1,2‐DCE, vinyl chloride, and ethene) significantly increased 50 to 150 days after treatment. Due to high concentration of CS in the source zone, a mass balance calculation, including chlorine, was possible. It showed that around 1 to 2 percent of the injected products were used to reduce the CS. A detailed analysis and 1D analytical modeling of CS concentrations showed that the treatment led to a large (two to three times) increase in dissolution of the organic phase. This explains why, despite an efficient treatment, the PCE and TCE concentrations remained virtually unchanged. Degradation rates also increased due to the treatment. Due to some differences in the source‐zone chemistry, it was not possible to differentiate between the ISCR and ENA efficiencies. © 2013 Wiley Periodicals, Inc.     

Field‐scale evaluation of a biobarrier for the treatment of a trichloroethene plume

In the 1960s, trichloroethene (TCE) was used at what is now designated as Installation Restoration Program Site 32 Cluster at Vandenberg Air Force Base to flush missile engines prior to launch and perhaps for other degreasing activities, resulting in releases of TCE to groundwater. The TCE plume extends approximately 1 kilometer from the previous launch facilities beyond the southwestern end of the site. To limit further migration of TCE and chlorinated degradation by‐products, an in situ, permeable, reactive bioremediation barrier (biobarrier) was designed as a cost‐effective treatment technology to address the TCE plume emanating from the source area. The biobarrier treatment would involve injecting carbon‐based substrate and microbes to achieve reductive dechlorination of volatile organic compounds, such as TCE. Under reducing conditions and in the presence of certain dechlorinating microorganisms, TCE degrades to nontoxic ethene in groundwater. To support the design of the full‐scale biobarrier, a pilot test was conducted to evaluate site conditions and collect pertinent design data. The pilot test results indicated possible substrate delivery difficulties and a smaller radius of influence than had been estimated, which would be used to determine the final biobarrier well spacing. Based on these results, the full‐scale biobarrier design was modified. In January 2010, the biobarrier was implemented at the toe of the source area by adding a fermentable substrate and a dechlorinating microbial culture to the subsurface via an injection well array that spanned the width of the TCE plume. After the injections, the groundwater pH in the injection wells continued to decrease to a level that could be detrimental to the population of Dehalococcoides in the SDC‐9^TM culture. In addition, 7 months postinjection, the injection wells could not be sampled due to fouling. Cleaning was required to restore their functions. Bioassay and polymerase chain reaction analyses were conducted, as well as titration tests, to assess the need for biobarrier amendments in response to the fouling issues and low pH. Additionally, slug tests were performed on three wells to evaluate possible localized differences in hydraulic conductivity within the biobarrier. Based on the test results, the biobarrier was amended with sodium carbonate and inoculated a second time with SDC‐9^TM. The aquifer pH was restored, and reductive dechlorination resumed in the treatment zone, evidenced by the reduction in TCE and the increase in degradation products, including ethene. © 2011 Wiley Periodicals, Inc.     

Stable Isotope Probing to Confirm Field‐Scale Co‐Metabolic Biodegradation of 1,4‐Dioxane

1,4‐Dioxane, a common co‐contaminant with chlorinated solvents, is present in groundwater at Site 24 at Vandenberg Air Force Base in California. Historical use of chlorinated solvents resulted in concentrations of 1,4‐dioxane in groundwater up to approximately 2,000 μg/L. Starting in 2013, an in situ propane biosparge system operation demonstrated reductions in 1,4‐dioxane concentrations in groundwater. The work detailed herein extends the efforts of the first field demonstration to a second phase and confirms the biodegradation mechanism via use of stable isotope probing (SIP). After two months of operation, 1,4‐dioxane concentrations decreased approximately 45 to 83 percent at monitoring locations in the test area. The results of the SIP confirmed ¹³C‐enriched 1,4‐dioxane was transformed into dissolved inorganic carbon (suggesting mineralization to carbon dioxide) and incorporated into microbial biomass (likely attributed to metabolic uptake of biotransformation intermediates or of carbon dioxide).  ©2016 Wiley Periodicals, Inc.     

Optimizing remediation strategies for a former dry‐cleaner site

Residual tetrachloroethene (PCE) contamination at the former Springvilla Dry Cleaners site in Springfield, Oregon, posed a potential risk through the vapor intrusion, direct contact, and off‐site beneficial groundwater uses. The Oregon Department of Environmental Quality utilized the State Dry Cleaner Program funds to help mitigate the risks posed by residual contamination. After delineation activities were complete, the source‐area soils were excavated and treated on‐site with ex situ vapor extraction to reduce disposal costs. Residual source‐area contamination was then chemically oxidized using sodium permanganate. Dissolved‐phase contamination was subsequently addressed with in situ enhanced reductive dechlorination (ERD). ERD achieved treatment goals across more than 4 million gallons of aquifer impacted with PCE concentrations up to 7,800 micrograms per liter prior to remedial activities. The ERD remedy introduced electron donors and nutrient amendments through groundwater recirculation and slug injection across two aquifers over the course of 24 months. Adaptive and mass‐targeted strategies reduced total remedy costs to approximately $18 per ton within the treatment areas. © 2010 Wiley Periodicals, Inc.     

Treatment of tar pond sludge in a circulating fluidized bed combustor

A series of tests to burn mixtures of tar pond sludge and coal was carried out using a mini‐circulating fluidized bed combustor (mini‐CFBC). During the tests, carbon dioxide, oxygen, carbon monoxide, sulfur dioxide, and nitrogen oxides in the flue gas were monitored continuously. Stack gas sampling was carried out for hydrochloric acid, metals, particulate matter, volatile organic compounds (VOCs), total hydrocarbons, semivolatile organic compounds (SVOCs), dioxins and furans (PCDD/Fs), and polychlorinated biphenyls (PCBs). Results showed that hydrochloric acid, mercury, particulate matter, PCDD/F, and metal concentrations were all below both the current limits and the gas‐release limits to be implemented in 2008 in Canada. The new 2008 emissions limits will reduce the maximum allowable concentrations of most pollutants by half. Thus, the maximum concentration for particulate matter will be 5 mg/m³ (from the current maximum concentration of 10 mg/m³);the maximum concentration for hydrochloric acid will be 5 mg/m³ (from 10 mg/m³); and the‐maximum concentration for dioxins and furans will be 0.032 ng/m toxic equivalent (from 0.08 ng/mcurrently). Sulfur capture efficiency was 89–91 percent. The percentage of fuel nitrogen converted to nitrogen oxides was of the order of 4.7 to 6.1, which is significantly lower than that of conventional pulverized coal‐fired boilers and well within the normal range for fluidized bed combustors (FBCs). PCB and polycyclic aromatic hydrocarbon (PAH) emissions levels were comparable or lower than levels reported in the literature for industrial‐scale FBCs. VOC concentrations were low except for benzene, for which the concentration was higher than that reported for pulverized coal‐fired utility boilers. In addition, carbon monoxide concentration was high at 1,200 to 2,200 parts per million. However, these carbon monoxide concentrations are typical of the mini‐CFBC firing coal. The trials showed that for 10 percent by weight tar pond sludge mixed with 90 percent by weight coal, the combustion was both stable and efficient. The tests demonstrated that CFBC technology is an environmentally sound option for eliminating tar pond waste sludge. © 2005 Wiley Periodicals, Inc.     

The use of zero‐valent iron injection to remediate groundwater: Results of a pilot test at the Marshall Space Flight Center

In situ treatability studies are being conducted to evaluate various in situ technologies to manage groundwater contamination at the NASA Marshall Space Flight Center in Huntsville, Alabama. The focus of these studies is to evaluate remediation options for contaminated (mostly aerobic) groundwater occurring within the basal portion of a clayey residuum called the rubble zone. The tension‐saturated media and unsaturated media lying above the rubble zone are also being treated where they make up a significant component of the contaminant mass. An in situ chemical reduction field pilot test was implemented (following bench‐scale tests) during July and August 2000. The test involved the injection of zero‐valent iron powder in slurry form, using the Ferox^SM process patented by ARS Technologies, Inc. The pilot test focused on trichloroethene (TCE)‐contaminated groundwater within the rubble zone. Maximum pre‐injection concentrations of about 72,800 micrograms per liter (μg/l) were observed and no secondary sources are believed to exist beneath the area. The potential presence of unexploded ordnance forced an implementation strategy where source area injections were completed, as feasible, followed by overlapping injections in a down gradient alignment to create a permeable reactive zone for groundwater migration. Eight post‐injection rounds of groundwater performance monitoring were completed. The results are encouraging, in terms of predicted responses and decreasing trends in contaminant levels. © 2003 Wiley Periodicals, Inc.